Search Documents

By Philip Lindstrom

T he Radon mine is in the north end of the Big Indian mining district in San Juan County, Utah. Hecla Mining Co. operated the mine from early 1955 to early 1964 through an operating agreement with Federal Resources, Inc. Development consisted of a 3-compartment, 690-ft shaft, 4 main levels driven on the ore horizon and a haulage level below the ore. Evaluation of physical and economic factors showed that this flat-dipping ore occurrence could be mined by a low-cost coal mining method. The value of the deposit was high and unusual pre¬miums were possible by clean mining. Complete extraction without loss of ore pillars, minimum ore dilution and high production per man were obtained by longwall mining.

Jan 12, 1964

By C. F. Frey, P. J. Ahern, J. F. Wallace

THE high affinity of molten titanium for oxygen and nitrogen has resulted in considerable difficulty in developing a satisfactory melting procedure. It has been found necessary to perform melting operations either in a vacuum or inert atmos-phere, and failure to obtain a satisfactory crucible material has necessitated the use of special melting techniques. These techniques have included cold-mold arc-melting utilizing both consumable and nonconsumable electrodes, skull-melting, drip-melting, and levitation melting.' It has been recognized generally that the melting of both titanium sponge and titanium scrap would be expedited by the use of induction-melting procedures but the lack of a crucible capable of containing molten titanium without objectionable contamination thus far has prevented the use of induction-melting procedures. An extensive investigation: which included the common refractory materials was not successful in developing a satisfactory crucible for induction-melting. Some success in induction-melting has been attained with the use of a graphite crucible material, but in all instances sufficient carbon contamination was encountered to cause an appreciable reduction in the optimum mechanical properties of the titanium or titanium alloys. These investigations"" report an increase in the carbon content from approximately 0.3 to 1.0 pct. A serious reduction in the tensile and forming properties has been observed as a result of this carbon contamination. The development of a satisfactory induction-melting procedure for titanium without undue contamination undoubtedly would have considerable economic significance. Such a process would be particularly useful in melting the large quantities of low-cost scrap now available that can only be reprocessed at considerable expense and difficulty by the more elaborate techniques referred to previously. In addition, the process could provide a satisfactory method of melting and alloying of bri-quetted sponge for forging ingots.

Jan 1, 1959

By AIME AIME

FRANK T. SISCO is a native of Lawrence, Kansas. He received his earlier education in Clinton, Iowa and his university training at the University of Illinois. His experience in the steel industry has included service in the chemical, testing, and metallurgical departments of the Illinois Steel Co., of South Chicago; the Hess Steel Corp., of Baltimore; the IJ. S. Naval Ordnance Plant at Charleston, W. Va.; and the American Steel and Wire Co., Waukegan, Ill. He severed for seven years as chief of the metallurgical laboratories of the U. S. Army Air Corps at Wright Field, Dayton, before coming to New York in 1930 to become metallurgist and editor of the Alloys of Iron Research, the position he now holds.

Jan 1, 1940

By AIME AIME

T HOUGH Ira B. Joraletnon has not had an eastern address since 1907, he is a New Yorker by birth, having been born at Antwerp, in the northern part of the state, on July 27, 1884. He got his scholastic training at Harvard, which gave him his A.B. degree in 1905 and an A.M. two years later. For the next fifteen years except for the war period, he was with the Calumet & Arizona Mining Co., with headquarters at Warren, Ariz., being assistant man- ager when he left that company in 1922. During the first World War he spent a year and a half in France, where he achieved the rank of major in the signal corps, air division.

Jan 1, 1941

By Phil Hulse

The Atlanta mine is located in east-central Nevada, approximately 360 km (225 miles) from Las Vegas. It lies in Lincoln County, 116 km (72 miles) south of Ely and 80 km (50 miles) northeast of Pioche. The property is currently operated by the Standard Slag Co. under a joint venture agreement with Bobcat Properties Inc, of Fort Lauderdale, Fla. Operations began in May 1975, and the mill is currently processing 109 000 to 122 500 t/y (120,000 to 135,000 stpy) of gold- and silver-bearing ore. Open-pit mining takes place in a breccia zone that occurs between Ordovician limestones and dolomites on the footwall and Tertiary rhyolites on the hanging wall. The quartz breccia ore is among the most abrasive in the world-shovel teeth must be replaced every week, 19-mm-thick (3/4-in.) steel chutes last about a month.

Jan 9, 1978

By Frederick Jr. Prime

THE first catalogue of Geological Reports of the United States was prepared by Prof. O. C. Marsh, and published in the American Journal of Science and Arts for 1867, vol. xliii, second series. Since then the list has more than doubled, and it was thought that the publication of a new catalogue, brought down to date, would be useful to many of the members of the Institute of Mining Engineers. The compiler will be most thankful to have any omissions or inaccuracies in the list sent to him, to be published as a supplement in the next volume of the Transactions. Especially to have the correct title, number of pages, plates, and maps of any volume on the list to which an * is prefixed, as he has been unable to personally consult such works. A preliminary list was issued last February, which has been almost doubled by the kindness of many friends. The writer desires more especially to express the obligations he is under to the following gentlemen The Chief of Engineers, U. S. A.; Principal Dawson, Mr. G. M. Dawson, Drs. B. J. Harrington and T. Sterry Hunt, of Montreal; Mr. H. Engelmann, of La Salle, Ill.; Dr. F. V. Hayden and Prof. J. W. Powell, U. S. Department of the Interior ; Prof. E. W. Hilgard, University of California; Prof. Henry Y. Hind, Windsor, N. S.; Prof. C. H. Hitchcock, of Dartmouth College; Mr. Henry A. Holmes, State Librarian, Albany; Maj. Jed. Hotchkiss, Staunton, Va. ; Prof. W. C. Kerr, Raleigh, N. C.; Dr. J. S. Newberry, of Columbia College ; Prof. W. H. Pettee, of the University of Michigan ; Dr. Samuel H. Scudder, Prof. N. S. Shaler, and Prof. J. D. Whitney, of Harvard College ; Mr. Sanderson Smith and Prof. J. J. Stevenson, of New York ; Mr. Addison Van Name, of Yale College, and Lieut. Geo. M. Wheeler, U. S. Engineers. PHILADELPHIA, 907 Walnut Street, October 1st, 1879.

Jan 1, 1879

By George A. Koenig

This new departure in assaying is the outcome of a long-felt desire to shorten the time required in muffle-assaying, as well as to do both crucible- and scarifi cation-work in one furnace. The first object in view was the gold-assay, which must always be a combination of the crucible- and muffle-work. The large lead buttons consume much time in their reduction by scorifying and cupelling. The Hoskins gasoline furnaces have been a great convenience, for years past, in that class of practice, where only one assay was required at a time. But even with them I found myself hampered, since the crucible-furnace only takes one crucible at a time, and my practice implies always duplicate assays. Another difficulty was to get the muffle up to the necessary heat and to maintain it at that heat. Whecever I had pumped myself into perspiration and out of breath, the question presented itself, " Is the muffle necessary to do this work properly ?" Hartmann and Plattner and all their blow-piping disciples have shown that very good results are obtainable by playing a direct flame upon the work-lead. Could this be done on the regular muffle-assay scale ? I placed a cupel upon a fire-brick, surrounded it with charcoal, and then played upon it with a Bunsen gas blow-pipe. The result was encouraging. With some care a 2.75-inch scorifier charged with 0.1 A. T. of a 100-ounce ore could be melted down and scorified without any apparent loss. I thought then of constructing a furnace with four blow-pipes in a row; but the combination of gas and charcoal seemed unpractical. Instead, I placed an F crucible, bottom up, in a Hoskins crucible-furnace. Upon this support I placed a charged scorifier. The rapidity with which a very refractory charge melted and scorified was simply amazing to me. Then a cupel was put in the place of the scorifier, the lid was moved sideways, and a blow-pipe was

Jan 1, 1899

Although the mining industry faced ever-increasing risks and uncertainties in 1974, it nevertheless pushed ahead with considerable rapidity in exploring and developing new orebodies-while expanding and improving the technologies of mining and exploration. Prepared by the SME Mining and Exploration Division, this section of the annual review covers the pertinent worldwide developments in the fields of geochemistry, geology, geological engineering, open pit mining, underground mining, rock mechanics, operations research, and solution mining.

Jan 2, 1975

Jan 1, 1904

In opening the meeting I wish to express my greatest pleasure at being able to greet this joint session of the Mining and Electrical Engineers. As engineering develops, we find that the border lines between the different branches of engineering become more and more indistinct; the several fields overlap so much that they are three or four layers deep in places. It is only an accident that we couldn't have had the Mechanical Engineers also as a formal part of this gathering, because they are quite as much interested in this subject as the Electrical or Mining Engineers. A little history may enlighten some of those who have not been close to this work. A year ago last summer, there was brought to the attention

Jan 4, 1919

By M. S. Seltzer

In a previous paper1 it was shown that activation energies for steady-state creep in lead sulfide single crystals varied with the concentration of electronic defects. For n-type lead-excess crystals, values for the creep activation energy, Qc, decreased from 2.9 to 2.2 ev as the carrier concentration increased from 1017 to 1017 electrons per cu cm, while Q, increased from 1.6 to 2.3 ev for p-type sulfur-excess crystals as the concentration of holes increased from 6 X 1017 to 1018 per cu cm. It was also shown in Ref. 1 that the Q, values could best be correlated with the sum of the self-diffusion activation energies in PbS, i.e., for a given concentration of electrons or holes Q, = QPb + Qs, where Qpb and QS are the activation energies for diffusion of pb210 and s35 in PbS. This result suggests that creep rates are controlled by at least two atomic defects, one for lead migration and one controlling sulfur transport. It would be most desirable to interpret these creep energies in terms of an atomic defect disorder model for lead sulfide. Studies of creep rates as a function of sulfur pressure2 indicate that the defects controlling creep rates are singly ionized lead and sulfur vacancies, VPb and Vs. This hypothesis can be more firmly established by determination of Q, under conditions of constant atomic defect concentration rather than constant electronic defect concentration as has been previously done. Therefore, several measurements have been made of Q, on crystals whose con- centration of lead vacancies or sulfur vacancies has been fixed by equilibration under appropriate sulfur pressure and temperature. It was indicated in Ref. 2 that high-temperature isotherms are available which show how the concentrations of various atomic point defects in PbS vary with composition over the entire homogeneity range for the compound. Two such isotherms are shown in Fig. 1 for 900" and 1000°K. Utilizing these isotherms the concentration of a given defect, say Vbb, may be held constant over a particular temperature range by adjusting the sulfur pressure as the temperature is changed. Thus the concentration of one defect suspected of controlling creep rates may be held constant while other defect concentrations vary. The apparent activation energy for formation of these defects can be obtained from the isotherms giving their concentration as a function of sulfur pressure. Activation energies for creep obtained under conditions of constant defect concentration can then be compared with defect formation energies and certain possible atomic defects can be eliminated as creep-controlling species. We have performed creep experiments as a function of temperature at a stress of 244 g per sq mm under conditions which fixed the lead vacancy concentration, V', at 1016, 3.2 x 1016, and 3.2 x 1017 cm-3, and one were the sulfur vacancy concentration, Vs, was held at lo17 cm-3. The results are presented in Fig. 2 as creep rate, k, vs reciprocal of absolute temperature, 1/T. Specimens 34, 35, and 36 were deformed under constant lead vacancy concentration while specimen

Jan 1, 1969

By George S. Rice

Ten years ago: October, 1914, the author had the privilege of giving an illustrated address on investigations of coal-dust explosions1 to this Institute at one session of its fall meeting in Pittsburgh, Pa,. On the following day, the members had the opportunity of seeing a large-scale explosion test at the Experimental Mine near Bruceton, in which the explosion was made to follow a predetermined path by means of rock-dust barriers of various types, which had prevented the explosive waves from reaching the outlets of the mine by the shortest paths.2 There was also shown a ((home-made" rock-dusting machine discharging the dust from a flexible nozzle, and a cement gun operated for the quick erection of a fire or ventilation stopping, such as might be put up after an explosion. Following that paper, there was presented a paper by J. Taffanel, Director of the Lìévin testing station in the Pas de Calais, which reviewed the French coal-dust investigations.3 A paper4 by Howard N. Eavenson contains lists of explosions that occurred in North America and Great Britain, from early in the 19th century to 1912; in France to 1903, and Belgium to 1909. Although explosions still occur, we are hopeful that we have entered a happier freedom from these visitations, as the result of increased knowledge of the causes and means of prevention. Looking back over coal-dust investigations, there appear to have been periods of advance and of stagnation. Coal-dust Investigations From the earliest times of coal mining, which chiefly affected Great Britain as the first nation to take up coal mining on a large scale, to the beginning of the 19th century, no one thought of coal dust as an explosive agency; firedamp was the cause dreaded. It was believed, when Sir Humphrey Davy invented his safety lamp in 1815, that a solution had been found for the prevention of mine explo-

Jan 1, 1925

By J. D. Prater, H. R. Spedden, E. E. Malouf

With the expansion of copper leaching of the various mine wastes at the Kennecott properties, additional copper recovery facilities have been required. A research and development program has been pursued to determine a suitable economic approach to the processing of the additional leach solutions contemplated. lnvestigations on laboratory and pilot plant scales covered electrowinning, solvent extraction, launder and vat type cells, activated launders, precipitation drums, and precipitation cones. This paper contains information on the development and use of a new precipitation-cone-type copper recovery plant, which provides many advantages over older systems. The application of research findings to the old art of leaching copper from copper-bearing mine waste has resulted in a significant contribution of copper to over-all copper production. For example, at the completion of the current expansion program at the Kennecott properties in the United States, copper produced from waste dump leaching will amount to about 25% of the total production. Formerly only 2% was derived from this source. This planned expansion of copper leaching focused attention on the problem of developing more efficient methods for the recovery of copper from greatly increased volumes of copper-bearing solutions.1 The detailed investigations which have been made in laboratory pilot plant and plant tests for the recovery of copper from copper-bearing solutions have included electrowinning, solvent extraction, ion exchange and cementation with iron in launders, precipitation drums, activated launders, and precipitation cones. The results of these investigations have led to the development of a new precipitation cone-type copper recovery system providing many advantages over older methods. ELECTROWINNING OF COPPER FROM COPPER-BEARING SOLUTIONS The direct electrowinning of copper from relatively dilute solutions of copper-bearing mine water, namely solutions containing 10 to 20 lbs of copper per 1000 gal, has always been an attractive possibility.2,3 By this method, high-purity copper powder can be recovered with a power consumption of 3.5 kwh per Ib of copper. However, once the solution strength de-

Jan 1, 1967

NORTH AMERICA ALASKA Anchorage.-Ames, M. B. Culver, H. W. Fiedler, H. L. Geehan, R. V. Langneas, O. O. Layfield, R. A. Parent, A. Saarela, L. H. Strandberg, H. Candle.-Robbins, J. S. Chichagof.-Russell, J. C. College.-Fox, E. F. Joesting, H. R. Lyman, R. F. Smith, M. C. -Wilcox, H. G. Douglas.-Cahill, W. E. Fairbanks.-Adams, J. M. CANADA Canadian Army Overseas.¬Ball, H. D. Bridges, O. Butterill, H. J. M. Lane, H. C. Millar, W. A.

Jan 1, 1942

By William B. Phillips

This paper was prepared at the request of Capt. A. F. Lucas, Chair man of the Institute's Committee on Petroleum and Gas; as a pre1iminary.discussion of the fuel oils which are used in the Southwest, giving their composition, uses, prices, etc. Should it afterward be found desirable, these observations may be extended over a larger area. In this connection, I suggest that samples of all kinds of fuel oils, including various tars, from all over the country, be collected and sent to some testing laboratory for examination. We would be glad to extend the facilities of the laboratory of the Bureau of Economic Geology and Technology, at the University of Texas, for this purpose, and to do the work free of all expenses. After such examinations are made and the results classified and studied, it would be possible to suggest specifications under which fuel oils should be purchased, and to arrive at some conclusions respecting the uniformity of such specifications, with due allowance for climatic and other more or less local conditions. While such specifications do not now depart from a common standard anything like as much as specifications for illuminating oils do, yet there are discrepancies which should not exist. Some of these discrepancies are of lessening importance, due to the pronounced tendency to distill every crude oil that can be distilled with profit, and to send residues into the market for fuel oil. Residues from the refineries are of a more uniform chemical composition and physical nature than many of the crude oils that go direct into the fuel market. The lower flash-point oils are disappearing from the fuel trade and in place of them we are getting oils that do not flash below 220" F., nor burn under 320" F. In the Southwest, it has not been long since we had fuel oils that flashed as low as 110" F., and the average flash point over a considerable period was 151" F. Now we are using oil that flashes at about 30" lower than the former burning point, which was 258" F. In other words, the flash point has risen, on the average, 100"; and the burning point about 75".

Jan 1, 1915

By Gerald G. Griswold, James O. Greenslade, Cherie Tilley, Richard Reseigh

INTRODUCTION The Harrison Western Corporation, a leading Denver based mine contracting and engineering concern, is presently engaged in sinking two 1,006 m (3,300 ft) shafts for the Phillips Uranium Corporation at their Nose Rock Project, approximately 13 miles northeast of the small community of Crownpoint in McKinley County, New Mexico. The Nose Rock Project is the first attempt by the Phillips Uranium Corporation to tap the deep uranium reserves in what has become known as the Grants Mineral Belt. (See Figure 1) Project Description Phillips Uranium Corporation's plan for the large 2700 metric ton per day (2950 tons/day) mining facility calls for a series of deep access and ventilation shafts ranging from 4.27 m (14 ft) to 5.49 m (18 ft) in diameter to approximate depths of 1,006 m (3,300 ft). The initial pair of shafts consists of one production shaft and one ventilation shaft separated by a distance of 91 m (300 ft). The interbedded layers of sedimentary sandstones and shales to be penetrated by the shafts contain several major water producing aquifers, the deepest being the mineralized zone called the Westwater Canyon Member of the Morrison Formation. A series of temporary and permanent water pumping stations is planned. Generally, the temporary stations are located above major aquifers to facilitate water removal while sinking through the aquifer and the permanent stations constitute what, in the final mode, will be the mine dewatering system. In addition, Phillips Uranium Corporation has In- stalled and is maintaining a system of depressurization wells that temporarily pump the major aquifers and considerably reduce the water inflows during shaft construction. The major aquifers are also chemically grouted prior to sinking. Site work for the project was initiated in the fall of 1976. Full scale shaft sinking commenced in November of 1977 on the 4.88 m (16 ft) diameter ventilation shaft and on the 5.49 m (18 ft) production shaft by another contractor. Harrison Western Corporation began work on the project on November 4, 1979 wlth the production shaft at a depth of 633 m (2,076 ft) and the ventilation shaft at a depth of 474 m (1,554 ft). This paper will address only the portion of shaft sinking completed by Harrison Western. Geology and Hydrology The Nose Rock Project is located on the Chaco Slope in the southern extreme of the San Juan Basin in northwest New Mexico. The southern San Juan Basin is generally bound by the Defiance Uplift to the west, the Zuni Uplift to the south and the Nacimiento Uplift to the east. The Grants Mineral Belt occupies most of the southern portion of the San Juan Basin and this project is located on the northern extreme of the Grants Mineral Belt. The San Juan Basin is comprised of sedimentary rock of continental, marginal-marine and marine origin, that dip northward from the Zuni Uplift and Chaco Slope into the interior of the San Juan Basin. (See Figure 2) Major Formations The major geologic formations to be penetrated range from mudstone and shales to siltstones and sandstones. The sandstones are highly productive aquifers which, under static conditions, would flow artesian. Water temperatures in the aquifers are high and therefore are a force to be dealt with. Temperatures range from 18ºC (65OF) in the upper aquifers to 48ºC (118º'F) in the lower. The mudstones are generally bentonitlc. (See Figure 2) GALLUP SANDSTONE: The Gallup Sandstone is the first major regressive wedge in the San Juan Basin of the Cretaceous era and at this project is about 35 m (115 ft) thick. It is medium grained and prior to depressurization carried a hydrostatic water pressure of over 72.5 kg per cm2 (1,031 psi) which 1s artesian. Compressive strength ranges from 334.7 kg per cm2 (4,760 psi) to 421.8 kg per cm2 (6,000 psi). Water temperature is approximately 30°C (86°F).

Jan 1, 1982

By E. T. Turkdogan, W. L. Worrell

The rate of reaction of hydrogen sulfide with ferrous sulfide was studied by measuring the initial rates of sulfidation of iron strips in hydrogen sulfide-hydrogen-argon mixtures at 670°, 800°, and 900" C. The time-dependent surface sulfur activity is derived from the instantaneous rate of sulfidation with the assumption that diffusion in the sulfide layer is in a pseudo-steady state with the gas-sulfide chemical reaction. The rate of sulfur transfer from hydrogen sulfide to the surface of iron sulfide is proportional to the partial pressure of hydrogen sulfide and inversely proportional to the activity of sulfur at the surface of the sulfide layer. The derived rate equation is based on the assumption that most of the surface sites on the chemisorbed layer of iron sulfide are occupied by sulfur atoms and that the slow rate-controlling reaction is the dissociation of hydrogen sulfide on the chemisorbed layer. The experimental results are in reasonable accord with this reaction model. 1 HE slow approach to parabolic growth rate in the sulfidation of iron in hydrogen sulfide-hydrogen mixtures is a manifestation of slow approach to surface equilibrium between the gas and the surface of the sulfide layer. For example, at 800°C and Fig. 7 in Part I, the parabolic growth rate begins after approximately 1 day of sulfidation time. With decreasing temperature and decreasing partial pressure of hydrogen sulfide, the time necessary to reach gas-sulfide surface equilibrium is much longer. These observations are similar to those reported previously by Turkdogan et al.' on the oxidation of iron to wustite in hydrogen-water vapor mixtures. The slow approach to gas-sulfide equilibrium is well-demonstrated by the results in Fig. 1 where the square of the weight gain per unit area, ( g S per sq cmI2, is plotted against time for gas mixtures having PH g//>H = 1.0 with 0, 25, 50, and 67 pct Ar at 800°C. The value of 1.5 X lo-' (g S per sq cm)' corresponds to almost complete sulfidation of the iron strip (- 0.05 cm thick) to iron sulfide. The points fall on S-shaped curves. If the inflection parts of the curves are considered to be linear, thus indicating parabolic growth rate and the establishment of gas-sulfide equilibrium, their slopes would have to be the same for a fixed ratio in the gas mixture. Such is not the case, and the slopes for the "linear" parts of the S-shaped curves are lower than the value when gas-sulfide surface equilibrium is established. The subject matter of this paper is the kinetics of the surface reaction of hydrogen sulfide with iron sulfide during the early stages of sulfidation of an iron strip. EXPERIMENTAL RESULTS The apparatus and materials used were the same as those discussed in Part I. In the present experiments of relatively short duration, a purified iron strip, 5 by 2 by 0.05 cm, which was suspended in the uniform hot zone of a vertical zircon tube, reacted with a flowing gas mixture of hydrogen sulfide-hydrogen-argon. The sample was suspended from a gold chain attached to a calibrated silica spring. The amount of sulfur picked up by the iron, which formed a layer of iron sulfide, was determined by measuring the displacement of a reference point on the silica spring, using a cathetom-eter. In all cases, the degreased sample was first annealed in a stream of oxygen-free dry hydrogen for several hours to remove any impurities such as oxygen, nitrogen, or carbon which might have been present on the surface of the sample.' The rate measurements were carried out at 670°, 800°, and 900° C in hydrogen sulfide-hydrogen-argon mixtures with pH2 s/Ph2 ratios from 4 to 0.1. In a few experiments of short duration no sulfur deposition was observed in gas mixtures with (comments concerning sulfur deposition at high pH s/ph ratios were made in Part I.) Typical examples of the results obtained are shown in Fig. 2 for two temperatures and two gas compositions. With the present experimental technique, reproducible rate data could be obtained only after a uniform

Jan 1, 1969

By C. W. Burrows

The burden a man can endure depends on its magnitude and the number of times it is applied, as well as on many other factors. The resisting power of steel likewise is dependent on many factors. The maximum load it can support indefinitely is much less than its possible momentary burden. A light load straining the metal far within its elastic limit, if repeated indefinitely, ruptures the metal. The magnitude of the stresses that may be alternately applied and removed without rupturing the material depends on the number of repetitions of the cycle; the intervening periods of rest; the thermal, electric, and magnetic conditions, as well as the presence of secondary streessses. While we are unable to formulate the law between the magnitude of repeated stresses necessary to produce rupture and the length of time during which these alternating stresses may be applied before rupture, my experience is that the time increases as the magnitude of the force decreases, according to a law which! to a first approximation, is exponential. In other words, F = Ce-t where F= magnitude of alternating stresses; t= time for which stresses are continued; C = constant, which depends on the conditions under which the operations are carried out. It is quite probable that the same type of law holds for the magnitude of a continuous force and its duration. When a rod of steel is subjected to the blows of a drilling hammer several things happen. First, one end is struck by the hammer and the other end is driven into the rock, thus causing a bodily displacement of the entire material of the steel drill. The greatest stresses involved in this bodily displacement are located at the two ends of the steel and manifest themselves by the distortion of these parts. Second, after the blow has been delivered, the steel drill, due partly to its own resiliency and partly to the resiliency of the rock, experiences a vibratory motion as a whole, this motion is quite similar to the bouncing of a rubber ball thrown violently upon a smooth pavement. Third, the free vibration of the drill is determined only by its own natural period of vibration. This motion involves all the characteristics of any vibrating body emitting sound. Certain elements of the rod will experience alternations of condensation and rarefaction and, in these regions, the individual steel

Jan 1, 1922

By Robert F. Mehl, Edward L. McCandless

Oriented overgrowths and intergrowths among both metallic and nonmetallic substances have been recognized and studied for well over a century. The work of Widmanstätten in 1808 on the geometrical structure in meteorites, a structure known by his name, demonstrated that oriented intergrowths can occur in purely metallic systems. This fact led to much of the early microscopic study of alloys, contributing greatly to the advance of physical metallurgy. The problem has been attacked again in recent years in a comprehensive fashion, with the object of discovering what atomic movements may occur during phase changes in alloy systems. Much of this work has appeared in the A.I.M.E. Transactions in a series of papers published by Mehl and coworkers beginning in 19311. Although many aspects of this general problem remain unsolved, it may be said that the orientation of a new phase forming by precipitation from solid solution or by transformation invariably bears a unique relationship to the orientation of the phase from which it formed, and that similarity in atomic patterns on atomic planes in the two phases play an important part in determining the orientation relationship. Analogous orientation relationships exist in oriented intergrowths in nonmetallic systems—mineral or inorganic. In 1827 Haidinger2 discovered natural intergrowths of hematite and magnetite, and demonstrated that the rough form of the magnetite octahedrons was delineated by small crystals of hematite, of which the basal (00.1) planes lay parallel to the octahedral cleavage planes of the magnetite. The description of this orientation relationship was later completed by von Rath3, who showed that the edge (00.1): (10.1) in hematite lies normal to the [Ill]

Jan 1, 1937

By Donald L. Everhart

SOONER or later intelligent exploration for uranium leads to these questions: Where did the metallic ions that formed the orebodies come from? What processes and geologic factors were involved in ore replacement? These matters, of course, make a big difference in how best to look for orebodies. Before these questions are discussed it might be well to point out other factors bearing on the subject. The whole business of uranium exploration is only a little over ten years old, participation by the public is only about six years old, and real interest and activity by more than a few large mining companies has arisen only in the past two or three years. Throughout this short period, uranium exploration has been affected by the unique influences of necessary security measures and by division of the over- all job into individual projects by a large number of specialists in diverse fields. This has meant that a normal interchange of information on the nature of uranium deposits has really only just begun. Com- pared to the vast amount of published studies on iron, copper, lead, zinc, and gold deposits over the past 50 to 75 years, current knowledge of uranium deposits is in its infancy and much of the pertinent information is still scattered about in a number of unpublished sources. The volume of reports on all phases of uranium exploration is now beginning to mount at a remarkable rate, and geologists with widely varying specialized backgrounds in uranium geology are engaging in spirited debates over the origin of uranium and the relative importance of geologic controls of various deposits.

Jan 9, 1954