Search Documents

By M. B. Kasen

eralized strain equation appear quite different they are really identical. This identity can be shown in a simple mathematical rearrangement. Referring to Eq. [I], the substitution of ln(1 +?E) for ? (where ?E is the engineering strain) yields: a =s8- (s8?so)e?1/?c) ln(1 +s8??E) [4] or s =s8?(s8?so)(l +?E)-1 [5] Replacing (1 + cE) with its equivalent, (l/lo): s=s8?(s8?so)l/€c [6] Adding and subtracting the quantity (s8 - so) yields: s=s8?(s8?so)+ (s8-so) l-(^)l/£c [7] = s0+(s8?so)ri-(^0)1/^l [8] Letting n = 1/?c it follows that: This equation will be seen to be identical to the generalized strain expression in Eq. [3], the coefficients a and b being equal to so and (s8?so)/?c or n(s8?so), respectively. Confirmation of the relationship noted above was provided by fitting experimental stress-strain data5 for 304 stainless steel (total strain from 0.072 to 1.15) at room temperature at a true total strain rate of 4 x 10-3 sec-1 to Eqs. [I] and [3]. In this study nonlinear regression analyses were used to evaluate the equation constants. The results of this evaluation are presented in Table I. When these constants are used in Eqs. [I] and [3] the curves obtained are coincident. It will also be noted that the value of n is equal to YE,, the value of a is equal to so, and the value of b is equal to (s8 - so)/Ec. These equalities are illustrated in Table I where the Voce constants in parentheses were calculated from a, b, and n values. Excellent agreement is seen to exist. It is concluded, therefore, that the Voce equation is, indeed, identical to the linear expression involving generalized strain. In applying the generalized strain concept to stress-strain data, it has been noted3 that data within what was termed the transition region (first few points in the plastic flow region) must be excluded from the analysis in order to obtain the linearity in Eq. [3]. A similar exclusion applies in the use of the Voce equation since an expression which would describe the strain-hardening region would usually be found to be not too effective in the elastic-plastic fillet2 which connects the elastic line to the strain-hardening region. These considerations further substantiate that Eqs. [I] and [3] do indeed describe identical behavior. Note added in proof. Since this manuscript was submitted for publication, correspondence with Professor S. R. Davies, University of Edinburgh, (of Ref. 3) indicated that his associates have also confirmed the identity between the Voce equation and the generalized strain concept. It is sometimes desirable to obtain a small grain size in super-purity metals. Unfortunately, the absence of impurities, the low recrystallization temperatures, and the low activation energies for boundary motion result in rapid growth of relatively few grains when conventional recrystallization practices are used. For example, Arajs et al.1 were unable to obtain a mean grain diameter less than about 0.4 mm in iron containing 38 at. ppm of impurity. The <1 at. ppm purity range in many modern superpurity metals results in yet larger limiting grain sizes. It is the purpose of this communication to describe a technique by which mean grain diameters as small as 30 µ have been produced in aluminum having an impurity content < 0.5 at. ppm. The technique should be applicable to superpurity metals other than aluminum and has potential applications to grain refinement of commercial alloys. The necessary and sufficient requirements for production of a small grain size are as follows: a) a large number of potential nucleating sites must be created randomly within the cold worked material, b) sufficient thermal energy must be provided at a rate that will simultaneously activate a large fraction of the potential nuclei, and c) the grain growth must be stopped shortly after grain impingement.&apos; A high density of potential grain nuclei may be cre-

Jan 1, 1970

By Francois Clerf

IRON ORE fields are situated in both the East and West of France (see maps). The eastern deposit is by far the most important from a tonnage point of view, not only in France, but in all Europe. The ores of this region are known as minette, and are situated in the Lorraine ore fields and the Briey plateau. The iron ores of the West are those of Normandy, Anjou and Brittany. Before the war, a large number of important German companies had acquired considerable interests in these western fields and a heavy trade with Westphalia had begun. Recently, however, conditions have changed and some of the mines of Brittany and Anjou are now idle. From a geological point of view, in Anjou and Brittany, a series of synclines extends from the northwest to the southeast, containing a number of seams of varying thickness and generally intercalated in Silurian and sometimes in Devonian formations. The ore is generally a hematite or a magnetite. The composition varies from 48 to 52 per cent of iron and from 8 to 12 per cent of silica. Con¬servative estimates indicate a con¬siderable tonnage of workable ores (150,000,000 metric tons).

Jan 1, 1936

By W. J. Taylor, H. J. Mutz, A. F. Brock

THE International Kickel Co. of Canada Ltd. operates five underground mines and an open pit. Four of the mines, the Frood-Stobie, Creighton, Murray, and Garson, are on the south range of the Sudbury Basin, map above, within a radius of 10 miles of the city of Sudbury, Ontario. The fifth mine, the Levack, is on the north range of the Sudbury Basin, 30 miles to the northwest of the city. The open pit is operating on surface ores of the Frood-Stobie orebody. Two pits were opened at the Frood-Stobie mine; the Frood section was started in 1938 and the Stobie section in 1942. To meet the heavy demand for nickel during World War 11, open-pit production was accelerated until it constituted over 40 pct of Inco&apos;s total tonnage. As a consequence open-pit ore was depleted considerably alhead of schedule; the Stobie pit was completed in the summer of 1951, and it is expected that mining at the Frood pit will be completed in 1953. The major program launched 10 years ago to develop additional underground production as a replacement of open-pit tonnage thus had to be greatly speeded up. This conversion to all-underground mining will be completed within the next two years, and the underground mines will then have an annual hoisting capacity of 13,000,000 tons. One of the new mines in the underground expansion program, the Murray, was brought into production in 1950. Ore production from the new Stobie section of the Frood-Stobie mine was commenced on a limited scale in 1951 and will be increased as the program progresses. Delivery of ore to the new Creighton mill was started in the summer of 1951 from the caving project launched at Creighton mine. When mining was started in the Sudbury district 65 years ago the ore deposits were opened on a small scale and mining methods conformed to a general pattern of small open cast pits, followed by open stopes as mining was extended below the pits. The open stoping methods used were heading-and-bench and shrinkage. In certain cases a type of cut-and-fill mining was used with drywall tramways and dry-wall chutes in the fill. As the mines were deepened,

Jan 1, 1954

By William Colby

INCREASING governmental control of human activities seems inevitable. Within the present generation railroad rates and the public sale of water, gas and electricity have been subjected to rigid regulation. The field of control is slowly but surely being enlarged, and it is the object of this paper to outline in brief space this tendency toward increased governmental regulation, as far as mineral resources are concerned. Our, dual form of government complicates the problem. We must deal not only with the powers of the Federal Government, but also with those of the individual States. In order to approach this question intelligently we must have some conception of the powers and jurisdiction of the States and the United States, respectively, over mineral lands and mineral production. Starting with the Federal Government we find it never owned any public domain within the States that formed a part of the thirteen original colonies and, for historical reasons, the same is true of Tennessee and Texas. The Mid-Western States were erected out of the public domain which was acquired by the United States through cession from the original States or by purchase from foreign nations. Congress early in the last century adopted a policy of leasing public lands containing lead deposits in a portion of this Mid-Western territory, but later abandoned that policy and disposed of such public, lands, mineral and non-mineral, outright so that they long since have practically all passed into private ownership and become subject to the general jurisdiction of the respective State governments. In the great public domain lying west of the Mississippi River, and in portions of some of the Southern States, the Federal Government adopted a new mineral land policy following the discovery of gold in California. (Acts of Congress of 1866, 1870, and 1872.) The mineral lands within these States, instead of being disposed of on the game basis as agricultural lands, as occurred in the Mid-Western States, were segregated from agricultural lands and sold under special laws intended to encourage mining, giving the miner the free right to locate and work these mineral lands without paying any royalty to the Federal Government. A miner could also obtain at slight expense a complete

Jan 1, 1930

By Lyle L. Marsh, David L. Douglas

CORRELATION was made between the heat treatment and hardness of three U-Ti alloys ranging in composition from 8.5 to 50 atomic pct Ti. The following important observations were made: 1) A direct quench of y U-Ti solid solution resulted in the formation of a hard martensitic phase in low-titanium alloys. 2) Subsequent tempering initially increased the hardness by the precipitation of a fine dispersion of U2Ti; further precipitation of U2Ti with tempering time eventually resulted in softening. 3) High-hardness levels were obtained also by isothermal transformation of an 8.5 atomic pct Ti alloy at 400º and 500°C. 4) The crystal structure of the phases present at the solution-treating temperature (one region in the phase diagram excepted) and the temperature within a given phase region affected the hardness of both quenched and isothermally transformed alloys. Introduction It has been known since 1887 that the mechanical properties of metals were dependent upon their microstructure. Sorby pointed out in that year that annealed gray iron castings were softer than chilled iron castings by virtue of the graphite which had replaced hard cementite in the microstructure. Over the years, interest has increased in the effect of microstructure on the mechanical properties of metals, and now high-strength levels may be achieved by bringing about the dispersion of a second phase or by other microstructural adjustments. The nature of a second phase in an alloy strongly influences the properties. For example, the size, shape, amount, and distribution of a second phase plays a very important role in the ultimate properties of an alloy. Microstructural control is achieved by heat treatments. Hence, any alloy system of potential use should be understood in terms of its response to heat treatment and the resultant effects upon the properties.

Jan 1, 1958

C. N. FEnner, New York City (communication to the Secretary) : A possible explanation of some of the&apos; phenomena of amalgamation cited by Mr. Bayliss and others has occurred to me. We know that if, to a quantity of mercury, gold and silver are added until a putty-like paste is formed, and if this mass is spread on a flat surface and pressure is applied, a more fluid portion of the mercury will be squeezed out from the rest, carrying gold and silver with it. The proportion of gold to silver will depend, I think, upon various causes and conditions—the relative chemical affinity which gold and silver have for mercury; the amount of pressure used; the presence of other metals:

Jan 1, 1898

By Frederick T. Williams

THE purpose of this paper is to discuss the relative merits of the large 31/8 in. machine and the small 21/4-in. tappett machine in driving development-headings ; and although the . data here presented were obtained from cross-cut headings alone, experience has shown that the results are equally true in drifting, raising and winning. Recently we drove two parallel cross-cuts through the same formation, using a 3k-in. machine at the breast of one cross-cut., and a 2k-in. machine of the same make at the breast of the other. The results of this work afforded an ideal comparison, since in both cases the headings were advanced through rock practically of the same hardness and breaking-properties ; the amount of sludging was equal, and there was no difference in the condition of the steel or the machines, in the air-pressure or in the experience of the operating-crews. Some operators in the Cripple Creek district contend that there is ground which cannot be handled with the small machine, the holes being too small to contain enough powder to pull the ground, etc. The results obtained in working the property of the Portland Gold Mining Co., however, show that the ground worked by them does not fall in this class. During a period of two years there have been driven, with the small machine, 4 miles and 308 ft. of development-headings, through a diversity of ground, including Pike&apos;s Peak granite (a coarsely porphyritic type of granite), highly indurated, andesitic or phonolytic breccia, true massive andesite, trachytic phonolyte, tuffas, and along dikes of decomposed basalt and hard phonolyte; in every instance a satisfactory record was made. The headings here described were driven through highly indurated, andesitic breccia, having a hardness of from 5.2 to 7.2

Mar 1, 1906

By D. Hanson

Fox most of their practical applications metals are required to with-stand stresses of appreciable magnitude: indeed, it is because they possess the quality of resisting stress without becoming permanently deformed that they find such extensive use in the service of man. Metals and alloys must, in service, usually behave as elastic substances-or nearly so. It is not difficult to satisfy this condition at ordinary temperatures. Iron and its alloys, especially the steels, are at normal temperatures excellent elastic bodies, capable of satisfying most of the mechanical requirements of the engineer: where electrical, chemical or other properties are impor-tant, which cannot be met by steels, it is usually possible to find a non-ferrous alloy such as nickel, copper or aluminum, which will prove satisfactory. When the metals or alloys are not inherently sufficiently elastic, cold-working or heat-treatment may develop elastic properties to a sufficient extent for practical needs. By means of relatively simple, rapid tests we can measure such properties as elastic modulus, limit of proportionality and proof stress, upon which design can be based with confidence. The case of the soft metals, such as lead and tin, is well known to be exceptional. They possess no definite limit of elasticity, and the value of proof stress or tensile strength depends to a great extent on the speed with which the test is carried out. Design here must be based on other considerations than a well-established theory of the proportionality of stress and strain. It is now generally recognized that steels and non-ferrous alloys possess at temperatures not greatly exceeding that of the atmosphere, characteristics quite different from those existing at ordinary temperatures, and that they assume qualities similar to those of the soft metals. Not only have they no limit of elasticity, but the proof stress and the ultimate stress depend on the time of application of the load. Flow under load may persist for long periods of time, possibly indefinitely, and the determination of a true maximum stress becomes a matter of great difficulty.

Jan 1, 1939

By Virgil R. D. Kirkham

RECONNAISSANCE of a part of southeastern Idaho and small strip of western Wyoming lying between longitudes 111° and 111° and 45&apos; W., and latitudes 43° and 43° and 30&apos; N., comprising an area of approximately 1330 sq. mi., was undertaken during the summer of 1923 for the collection of data regarding the oil possibilities of the region. TOPOGRAPHY, SETTLEMENT, AND ACCESSIBILITY The entire area lies within the upper Snake River drainage basin. Snake River flows through the northeastern and eastern part of the area in a northwesterly direction. The entire drainage system has been controlled by the structure of the sedimentary beds in the area, which exhibit numerous alternations of hard and soft strata with consequent unequal erosion. The headwaters of the most important streams, as well as many others, flow in a northwesterly or southeasterly direction along

Jan 1, 1925

By A. E. Brugger

SOME 2,000 years ago Pliny is supposed to have said, "Out of Africa always something new." It may perhaps even now be news to a great many that the Belgian Congo has in recent years been producing approximately a quarter of a ton of diamonds annually. For that is what the 1 1/4 million carats, the recovery from 40-odd operating mines, and about 20 or 25 per cent of the world&apos;s normal consumption, amounts to. In 1915, first exploitation operations produced less than 50,000 carats from two mines. The rapid expansion of operations following the Euro¬pean war meant a most rapid development of a virgin land. The interior is now reached by air in one day from the mouth of the Congo River, where steamers unload mail and passengers from Antwerp. This trip formerly consumed 4 to 6 weeks by a narrow-gage, wood-burning, railroad around the rapids of the lower Congo and Livingston Falls; by river boat to the heads of navigation, Djoko Punda on the Kasai or Luebo on the Lulua; and thence by caravan of native porters over narrow-trails to head¬quarters on the Tshikapa. Hundreds of miles of automobile roads have been constructed over veldt and through forest, bridging streams and ferrying rivers. The railway from Capetown to the Katanga copper district to the East, once two months away by trail is now reached in 2 or 3 days over fair automobile highway. Native "boys" who a few short years ago wore little more than a smile and a string of beads and to whom a wheelbarrow was a complicated piece of machinery, are today driving Fords, tending boilers and engines and operating electrical equipment, or are capable mine workmen, machinists and artisans, and dressed in all manner of cast-off white man&apos;s clothing. Even as late as 1920, due to difficulties of securing and transporting machinery during and just after the war, the crudest hand operations were the rule for the excavation, sizing, and concentration of the diamondiferous gravel. All washing and concentration is now mechanized, using steam or electric power, and where operations are sufficiently large to permit competition with native labor costs, excavation and transportation are also accomplished by machinery.

Jan 1, 1932

By E. R. Parker, D. L. Martin

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944

By D. L. Martin, E. R. Parker

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944

By Norman Weiss, H. W. Kaanta

CUSTOM ores reach across the New Mexican mesa to American Smelting & Refining Co.&apos;s new lead-zinc mill at Deming. The influx of ores justified increasing mill capacity from 12,000 tons per month to 20,000 tons per month with the installation of a second milling section. Deming mill has met a complex material handling problem with the successful instrumentation of modern machinery and knowledge. A tight, compact plant does a big job with the aid of the latest ore moving equipment. Location and Layout The mill is located three miles northwest of Deming in the tumbleweed covered valley of the Mimbres River, 30 miles north of the Mexican border. Deming has a population of 4000 and is about halfway between Lordsburg and Las Cruces and 54 miles southeast of Silver City. The AT&SF and the SP railroads and U.S. Highways 70, 80, and 260, cut across the mesa to the town. Asarco mill station is east of the AT&SF single track, and north of Deming. The nearly level terrain is covered with fine sand supporting only yucca and tumbleweed. Compacted gravel at depth affords excellent foundation bearing. The climate is semi-arid, but the district is underlain by water-bearing strata. Tailing disposal space is plentiful. The Deming site appeared favorable because of easy rail and highway access, central location in a mining district, excellent climate, plentiful water supply, space for all present and future requirements, and proximity to a town. The milling plant is a 250-ft square. The rail spur forms the west side; sampling plant, fine-ore conveyor and bins are on the east; track hopper, primary conveyor, and crushing plant lie on the south; and the mill building completes the north side of the square. Construction The mill site was chosen and the land purchased in 1,946 and 1947. Design began in 1948, and Stearns-Roger Mfg. Co. of Denver started construction in June 1949 completing work in April 1950. Construction is steel and concrete throughout, with main concrete floors supported on cellular steel beams. The building is covered by galvanized corrugated iron, attached to the frame by welded Nelson studs, and made dust tight at the joints with roofing paper and asphalt sealing compound. Crushing and Sampling Custom ores, delivered to the mill by railroad cars or trucks, are weighed on arrival. A Robbins car shaker dumps the ore into a 100-ton capacity steel hopper. Adjacent is a 40-ton truck hopper. Three 36-in. Pioneer apron feeders supply ore from the receiving hoppers to a 36-in. conveyor which runs to the crushing plant. A tramp-iron detector protects the primary crusher except when handling magnetite containing ores. A 2 ½ -in. spaced grizzly precedes the primary Traylor 24x36 in. jaw crusher set at 4 in. A Symons 4-ft cone crusher in closed circuit with 48x78 in. Robbins Gyrex screen completes crushing to 5/8 in. The discharges of both crushers drop upon a common conveyor, which, after gaining sufficient elevation, transfers ore to a return conveyor. This return conveyor passes under a suspended magnet and over a magnetic head pulley to the Gyrex screen. Screen undersize is conveyed by a 20-in. belt to the sampling plant. Crushing rate varies from 60 to 90 tons per hour. Ores containing magnetite and pyrrhotite nullify the magnetic detector and overload the magnets

Jan 1, 1952

By M. J. Bradley, P. H. Dike

THE art of melting nonferrous metals, in smelting, casting, and in compounding of alloys, is highly dependent on a knowledge of the temperature of the metal. This knowledge may reside in the experience and judgment of the melter, or it may be based on measurement by suitable instruments. It-is our purpose to discuss briefly the instruments available for such measurements, and more at length the present, practice in molten metals, without recommendation. In the limits of time and space allotted, we can do little more than mention the available methods of measurement that are directly applicable in this field. In the 1939 edition of the Metals Handbook, issued by the American Society for Metals, pages 285-310, there is a more extensive discussion of pyrometry than can be attempted here, which should be referred to for details we must omit. For reasons that will appear, thermoelectric pyrometry will constitute the major portion of our discussion of the subject, only limited attention being given to radiation or optical pyrometry. METHODS OF MEASUREMENT THERMOELECTRIC PYROMETRY A thermocouple consists of two dissimilar wires, or a wire inside a tube of a dissimilar material, joined together at one end, which is placed in the region or medium where the temperature is to be measured, while the other ends are connected through suitable lead wires to a voltage-measuring device, which may be a millivoltmeter or a potentiometer. An electromotive force is generated in the circuit, which is proportional to the difference in temperature between the hot junction and the junctions of the lead wires to the measuring instrument. If this latter temperature is maintained constant, the e.m.f. measured varies only with the temperature of the hot junction. Every thermoelectric pyrometer is calibrated for a particular cold-junction temperature such as 0°F., 32°F. or 75°F., but usually it is more practical to compensate instrumentally over the probable range of cold-junction temperatures than to maintain the junction at the particular temperature for which the instrument was calibrated. Thermocouple Materials Only a very few pairs of metals are in frequent use for pyrometric measurements. The most generally used are iron-constantan for temperatures up to 1500°F. in oxidizing and up to 1800°F. in reducing atmospheres and chromel-alumel, which may be used in oxidizing atmospheres at temperatures up to 2400°F. for intermittent service. The accuracy of the latter deteriorates rapidly at temperatures above 2200°F. Platinum vs. platinum-rhodium thermocouples may be used up to a temperature of 3000°F , but they are easily contaminated by slow absorption of

Jan 1, 1946

By George Macready

TRINIDAD, British West Indies, is an island near the north coast of South America, situated between latitudes 10° and 11° N:, and. opposite the numerous outlets of the Orinoco River Delta. It is separated from Venezuela by the Gulf of Paria (salt, water) and straits over 5 mi. (8 km.) wide. The area of the island is approximately 1750 sq. mi. (453,- . 250 hectares) and the population is approximately 400,000. The climate is tropical with an annual rainfall of from 45 to 60 in. (114 to 152 cm.). The oil fields consist of several units, or fields, located in the southern half of the island. Approximately 90 per cent. of the total production has been yielded by fields situated within 7 mi: (11.3 km.) of the famous asphalt lake and on the southwest peninsula. The most important producing fields, or units, are the following, which are shown on the accompanying map: Brighton, or Pitch Lake Field, operated by the Trinidad Lake Petroleum Co., Ltd., is situated beside the famous Pitch Lake; it, even encroaches on the lake. Vessigny Field, operated by the Trinidad Lake Petroleum Co., Ltd., is situated 2 mi. (3.2 km.) south of Pitch Lake. Lot One Field, operated by the Petroleum Development Co., Ltd., the United British Oilfields of Trinidad, Ltd., and Stollmeyer, Ltd., is situated 3 mi. south of Pitch Lake upon Lot One of Morne 1&apos;Enfer Forest Reserve and adjoining properties. Parry Lands Field, operated by the United British Oilfields of Trinidad, Ltd., and the Petroleum Development Co., Ltd., is situated 3;2 mi. south of Pitch Lake on Lot Three of Morne l&apos;Enfer Forest Reserve and adjoining properties. Point Fortin Field, operated by the United British Oilfields of Trinidad, Ltd., is situated at Point Fortin, 6 mi. southwest of Pitch Lake. Fyzabad Field, operated by Trinidad Leaseholds, Ltd., is situated several miles southwest of Fyzabad Village and 6 mi. south-southeast of Pitch Lake. Barracpore Field, operated by Trinidad Leaseholds, Ltd., is situated several miles south of. San Fernando and 15 mi. (24.14 km.) east of Pitch Lake.

Jan 9, 1920

By Strathmore R. B. Cooke, Iwao Iwasaki, C. S. Chang

The effects of aeration on an aqueous suspension of pyrrhotite were studied and their results correlated with flotation tests using xanthates as collectors. The effects of copper activation and of pH variation were determined and possible mechanisms postulated. PYRRHOTITE has long been considered a gangue mineral to be eliminated as tailing in the treatment of various sulphide ores. However, in recent years the world-wide lack of sulphur resources has called attention to this mineral as a potential source of both sulphur and iron. Its importance as an economic mineral, however, has not been particularly emphasized. For this reason very little is known about its response to flotation, except that it can be depressed easily in alkaline circuit, by long aeration,1,2 addition of oxidizing agents,3 or by starch.&apos; The object of this work was to study the floatabil-ity of pyrrhotite. This includes the effect of oxidation by aeration, of copper activation, and of change in pH. Preparation of the Pyrrhotite Sample: It was desirable that the highest grade of pyrrhotite obtainable be used for this experiment, since the presence of other minerals could affect the surface properties.5 However, no pyrrhotite was available as crystals, and massive deposits of hydrothermal origin commonly contain considerable amounts of chalcopyrite. Pyrrhotite concentrate was, therefore, prepared from a sulphide deposit occurring near Aitkin, Minn. The deposit is of pyrometamorphic nature consistirlg mainly of pyrrhotite and pyrite with graphite, silicates, and carbonates as gangue. The ore, already crushed through 3 mesh when received, was screened at 65 mesh and the undersize discarded. The oversize was crushed through rolls, and then stage-ground dry in an Abbe porcelain mill, the —65 mesh portion being screened out after every 15 min of grinding until all the material passed through this size. The ground product was then concentrated with a drum-type dry magnetic separator. The rougher concentrate was cleaned twice and then demagnetized. The final product was split in a Jones splitter and stored in air-tight bottles. Microscopic examination of the concentrate showed that it was relatively clean and free of pyrite, locked particles, and gangue. By means of the krypton gas adsorption method," the specific surface was determined to be 3000 cm2 per g. The chemical and screen analyses of the final concentrate are given in Tables I and II respectively. It is a well-recognized fact that the oxidation of some sulphide ores during stockpiling, grinding, and conditioning affects their flotation behavior. The problem of oxidation may become serious in the case of pyrrhotite, since this is known to be more easily oxidized than many other sulphides. To ascertain the extent of oxidation, an experiment was carried out by aerating an aqueous suspension of pyrrhotite with air, oxygen, and nitrogen as follows. A 300-g sample of pyrrhotite in 2700 ml of water was agitated and simultaneously aerated in a Fager-gren-type laboratory flotation machine. A Precision wet test meter was connected to the air inlet valve, the flow rate of the gas being kept constant at 0.3 cu ft per min throughout the experiment. Samples of approximately 30 ml each were taken from the cell at 0, 4, 10, 20, 35, 60, and 90 min. After the pH was taken, each sample was filtered and the filtrate was analyzed for total iron and sulphur. The iron was determined colorimetrically by the thioglycolate method using a green filter.&apos; The filtrate was oxidized with bromine to convert all of the soluble sulphur compounds into sulphate and this was determined with a Parr turbidimeter." When aeration tests were made in alkaline circuit, calcium hydroxide or sodium hydroxide was added at regular intervals to maintain a constant pH. A similar procedure was followed in an experiment to determine the abstraction of copper. ion by pyrrhotite. In this case various quantities of cupric chloride were added. The filtrate from each sample taken was analyzed for copper, total iron, and sulphur. The carbamate method with a green filter was used for the copper analysis,&apos; since this method could tolerate a considerable amount of iron in the solution. A pneumatic cell, made from a 350-ml fritted glass Buechner funnel, was used for this experiment. The detail of the assemblage has been described elsewhere." In the present work a stainless steel baffle was inserted in the cell. This baffle overcame the tendency for the coarse pyrrhotite particles to be swirled around the wall of the cell and thus fail to collect in the froth. A 50-g sample of pyrrhotite was added to the cell which contained 260 ml of water. When pretreat-ment of the sample was desired, reagents, such as activator and pH regulator, were then added and the pulp was conditioned for a specified conditioning time. Prior to the addition of the collector approximately 15 ml of the solution were removed for pH measurement and for iron and sulphur analyses. Copper when used as activator was also determined. Collector and frother were then added and the pulp was conditioned for an additional 2 min. Air was admitted to the cell and the froth removed. The separation required from 4 to 6 min, depending on the characteristics of the froth. The float and non-float products were filtered, dried, weighed, and assayed for iron.

Jan 1, 1955

By George A. Packard

THE experiments here described were made under my supervision while temporarily acting as head of the Department of Metallurgy at the Missouri School of Mines, at Rolla. The work was done by Messrs. W. E. Brown, W. C. Richards, and F. L. L. Wilson, and the description of the results forms a portion of a thesis presented for the degree of Bachelor of Science. These results are submitted because I have seen no description of the application of pot roasting to the treatment of a copper-concentrate. This work followed that already described in the discussion of the &apos; Lime-Roasting of a Galena-Concentrate,"&apos; and was similarly occasioned by the lack of a furnace of the reverberatory type in which the copper-concentrates could be smelted. The material for the tests was a mixture of three lots available. The first consisted of 8-mm. jig-concentrates and the second of 0.5 mm. table-concentrates, from the San Juan district, Colo. Both contained pyrite, chalcopyrite and galena. The third was a lot of copper-ore, found in the laboratory, which had been crushed through 8-mm. screen, and had at some previous time, before the laboratory roasting-furnace was torn down, received a partial roasting. The analyses of these ores are given in Table I. In order to determine the applicability of pot-roasting as to each lot of ore, and the effect of varying proportions of lime, six preliminary tests were made in a " size N " Battersea crucible, 9 in. high by 6 in. in diameter at top, with a 5/8 in. hole bored through the bottom. The crucible was set in the upturned elbow of a 2-in. pipe, the joint being luted with clay; and air was obtained from a receiver supplied by a compressor. The

Jan 1, 1908

By E. G. Leonardon, C. Schlumberger, M. Schlumberger

Last year the authors presented a paper that discussed the various electrical measurements they perform in drill holes, which they name "electrical coring."&apos; The object of the present paper is to give a brief account of the points of scientific interest that have been elucidated by further field work and laboratory research, as well as the economic results that have been attained recently. The practical examples given in this paper are drawn, for the most part, from the field work performed in Russian oil fields during the years 1931 and 1932. This is due to the fact that, thanks to the comprehensive cooperation of the Russian geologists and scientists, the authors are allowed to make public a large amount of recant information. In other countries in which the authors are engaged in similar work, the competition between private companies makes it imperative, for a considerable lapse of time, to avoid publication of the results obtained. The following points will be discussed successively, under separate headings: 1. Electrochemical phenomena in drill holes. 2. Stratigraphic correlations and tectonic studies. 3. Relations&apos; between the productivity of oil horizons and their electrical resistivity. 4. Location of coal seams. 5. Summary and conclusions. Electrochemical Phenomena in Drill Holes Technical Publication 462l described the author&apos;s discovery concerning the existence of important differences of potential spontaneously gener-

Jan 1, 1934

By E. P. Abrahamson II

The effect of transition element binary solid-solution additions upon the recrystallization temperature of vanadium has been investigated. Cr, Fe, Co, Ni, Mo, Ru, Rh, Os, and IY lower the recrystallization temperature, while Ti, Mn, Zr, Cb, Pd, Hf, Ta, W, Re, and Pt raise it. The majority of elements have their greatest effect in less than 0.15 at. pet. Both the rate of change of recrystallization temperature with atomic percent solute and the limit of initial linearity are found to Correlate with the free atom grozdnd state outer electron configuration of the sollte element. THE work of Abrahamson and Grant1 and Abraham-son and Blakeney2 has shown that the solute&apos;s elec- tron configuration appears to be a prime determinant of both brittle-to-ductile transition and recrystallization temperature in dilute binary alloys. It has also been shown by Abrahamson3 that the limit of linearity, i.e., the limit of initial linear change of recrystallization temperature with atomic percent solute, is also a function of the electron configuration of the solute in iron base alloys. Because of the systematic nature of the solute electron configuration correlation, it is to be expected that some systematic variation might be observed upon changing the solvent. Thus, this study of recrystallization in vanadium base alloys is the first of a series aimed at defining the role played by the electron configuration of solute in determining the recrystallization characteristics of dilute transitional alloys. PROCEDURE All alloys were made using 99.8 pct V containing 0.011 C, 0.024 N, 0.08 0, 0.006 H, 0.035 Ta, and

Jan 1, 1962

By R. A. Morse, P. M. Bridges, L. E. Wilsey, Howard N. Hall, P. L. Terwilliger

Theoretical and experimental investigations of a constant pressure gravity drainage system are reported. Experimental data are presented to show that recovery to gas breakthrough by gravity drainage is inversely proportional to rate. The gravity drainage reference rate, which is numerically equal to the so-called "maximum theoretical rate of gravity drainage" is shown to have no particular significance from a recovery standpoint. Before this rate can be used as a basis of comparison for recoveries, it is necessary that the relative permeability and capillary pressure characteristics and displacing fluid viscosities be identical for the systems compared. A method is presented by which accurate prediction of the performance of a gravity drainage system can be made. Close agreement between experimental and calculated drainage performance shows that steady state relative permeability and static capillary pressure data can be used to describe fluid displacement behavior. The very wide range of liquid recoveries before gas breakthrough which result from production rate variation alone demonstrates the importance of this factor in planning depletion of a gravity drainage reservoir. Calculated results are presented which show that little additional recovery can be expected from a high pressure gravity drainage system between the times of gas breakthrough and attainment of such high gas/liquid ratios as to make further pressure maintenance impractical. INTRODUCTION It bas been recognized for some time that gravity forces play an important part in the recovery of oil from some types of reservoirs. Field experience has shown that under certain conditions, gravity drainage can result in very high oil recov- eries. Qualitative reasoning has led most engineers to the general conclusions that: (1) Where gravity drainage is important, the reservoir pressure should be maintained by gas injection at the crest of the structure to prevent shrinkage of the oil in place and to keep a low viscosity so the oil can drain at the fastest possible rate. (2) Recovery by gravity drainage is rate sensitive. A survey of the literature indicates that while considerable work has been done on the effects of gravity in oil production problems, no satisfactory method of calculating the performance of gravity drainage reservoirs has been reported.1,2,3,4,5 In the absence of any proven method of calculating reservoir performance, the level at which pressure should be maintained and the rate of production for most efficient operation has been open to debate. The limits and general character of the recovery us rate relationships are apparent from the following: As rates of production approach zero, oil will drain by virtue of its own weight fast enough that the saturation distribution is always approximately the same as the original static capillary distribution. That is, at the gas-oil contact the liquid saturation goes from 100 per cent to a value of perhaps 10 to 30 per cent in a very short distance, so that as production continues. a relatively sharp gas-oil contact moves down-structure, leaving a very low residual oil saturation in the originally oil saturated zone. At very high rates of production, the oil that drains by virtue of its own weight is negligible and recovery will approach that of a horizontal gas drive, leaving a much higher residual oil saturation. At intermediate rates of production. recovery should be between these extreme*. Despite the lack of quantitative methods, tentative agreement had been reached on the question of optimum producing rate. It has been generally concluded that rather sharp decrease in recovery would occur at rates of production above the "maximum rate of gravity drainage" and hence this rate should not be exceeded. The "maximum rate of gravity drainage" is defined as the rate of production from a 100 per cent

Jan 1, 1951