Search Documents

By P. P. Gregory

The rate of drilling operations in the West Texas district during 1940 was approximately equal to that of 1939. The total number of wells dillled in the area during the year was 1834, of which 1716 were completed as oil producers, 12 were gas wells and 106 were dry holes. The number of wildcat wells drilled during the year was comparatively small. The drilling of inside locations in proven areas and the drilling of wells for the purpose of extending the productive limits in producing fields constituted the bulk of development during 1940. Gaines County led all other counties in the district in the total number of oil-well completions. The oil production totaled 83,345,381 bbl., the highest figure for any year since proration was begun. The 1940 oil production exceeded the 1939 production by approximately four million barrels. Discoveries While comparatively few new oil-producing areas were discovered during 1940, it appears that the oil production found in simpson lime in the Abell field, pecos County, was an outstanding discovery for the year. This was the second Ordovician discovery in Pecos County. Taubert, McKee & Siemoneit located its discovery well, V. W. Crockett No. 1, set. 4 1/2 H. & T. C. R.R, co, survey in the Imperial area of northwestern Pecos County. The top of pay was encountered at 5270 ft., and the well was bottomed at 5357 ft. in simpson lime, on act. 17, I940. The initial production was 928 bbl. of 43" gravity sweet oil in 11 hr. 23 min., flowing naturally through 2-in. tubing with gas-oil ratio of 783 cu. ft. per barrel. Following the completion of the discovery well, large blocks of land were leased in the area, and several locations were made toward the close of the year. There is every indication that the Abell field will become a major producing field in the West Texas district. There was no pipe-line outlet for the field at the end of the year. Shipley-Silurian field, discovered by the Gulf Oil Corporation, appears to be another major addition to the oil reserves in 1940. The discovery well, Wristen Brothers No. 5, is in sec. 18, block 5, H. & T. C. R.R. Co. survey in Ward County. The well was drilled to a total depth of 9187 ft. and was plugged back to 7075 ft. The Silurian lime section was acidized with 3000 gal., from 6993 to 7075 ft., and on Dec. 5, 1940, the well was completed for initial production of 3040 bbl- of 32.2" gravity oil in 24 hr., flowing through tubing. Todd Deep field, Crockett County, was discovered by the Continental Oil Co. et al. The discovery well, J. S. Todd No. 2, set. 29, block WX1 G.C. & S.F. R.R. Co. survey, was completed on April 3, 1940. The top of pay was encountered at 5623 ft., and the well was bottomed at 5691 ft. for initial production of 1613 bbl. of 40.6' gravity oil flowing naturally through 2-in. tubing. The pay section was found in Strawn lime of Pennsylvanian age. There were six producing wells in the field at the end of the year. This appears to be another major discovery in 1940. There was no pipe-line outlet in the field at the end of the

Jan 1, 1941

By AIME AIME

DATA in this report enable comparisons to be made within the bituminous coal industry and comparison as well with copper and steel in respect to capacity and overdevelopment. The conclusions reached from the data will tend to correct numerous current misconceptions. The data have been prepared by various members of the Coal and Coke Committee of the A.I.M.E., from the most authentic sources avail¬able, and cover the period 1913-1924 wherever possible. CAPACITY AND OVERDEVELOPMENT Table 1 shows statistics for the industry, mainly from the U. S. Geological Survey sources, but partly from the U. S. Coal Commission reports. The mine capacity with equipment and labor as of given date is calculated for each state by obtaining the total man days worked as reported by the operators, and dividing this figure into the total production, getting the production per man day; this figure times the number of men employed times 308 (a theoretical full working year) equals estimated full-time capacity. Two major objections are made to this method-one that the total number of men employed is used instead of the number actually working, and the other that the number of days used only deducts Sundays and five holidays. Covering the first, the same number of men is used in estimating capacity as is used in actual production, and this condition exists at all times. Regarding the second, the opinion is general among coal men that 280 days is as great a figure as should be used, as it is practically impossible to keep any mine working full time at the same daily rate as when it is working part time. The capacity, as estimated on this basis, is much more nearly the true capacity, although even with present railroad efficiency this amount of coal could not be moved.

Jan 1, 1926

By C. R. Fettke

In 1914, the officials of the Brundred Oil Corpn., faced with the problem of introducing new methods to increase production in the old and nearly depleted pools of Venango County, became interested in the Smith-Dunn (Marietta) process which was at that time being tried out in southeastern Ohio and which was already yielding very encouraging results. A license to use the process in Pennsylvania was secured from the owners of the patents. These patents were later declared invalid. The method was first used in Pennsylvania on a property consisting of about 434 acres, of which 300 are productive, at Hamilton Corners, 15 miles northwest of Oil City, in Cherry Tree and Oakland Townships, Venango County. The producing horizon is the First Sand of the Venango Group. A small oil pool was opened up in this vicinity in 1904. By July, 1916, when the compressed air was first introduced to restore pressure, the production had dropped to a point where it was no longer possible to continue profitable operation. From that time until March, 1927, over 100,000 bbl. of oil have been recovered from the tract. The property is being operated at present by the Brundred Oil Corpn. and LUX. The 1926 production, amounting to 10,650 bbl., was only 400 bbl. short of the maximum reached during any year of the 10-year period that the process has been in operation. Inasmuch as the Hamilton Corners pool is the first one in Pennsylvania in which the Marietta process was tried out, and the one in which it has been longest in continuous operation, considerable interest attaches to the results obtained. Through the courtesy of H. D. Brown and W. J. Brundred, officials of the Brundred Oil Corpn., all their data on this operation were made available to the writer in connection with an investigation of rejuvenation methods in the State for the Pennsylvania Geological Survey. Stratigraphic Position of the Producing Sand The producing sand at Hamilton Corners is encountered at depths of from 364 to 560 ft., depending on the location of the well and the topog-

Jan 1, 1928

By W. E. Crawford

The Fresnillo Company's mill at Fresnillo, State of Zacatecas, Mexico, treats oxide ores from the Fresnillo mine, dump ores and underground ores from the Plateros district, company leases and custom ores from the Zacatecas district, custom ores from other districts and tailings from old dumps at Fresnillo. The normal capacity of the mill is approximately 2600 dry short tons per 24 hours (a ton of 2000 lb.). The final product of the mill is a precipitate containing gold and silver, which is smelted and shipped as doré bullion to the refinery of the Compania Minera de Penoles, S.A., at Monterrey, State of Nuevo Leon, Mexico. The geology of the district was described in 1923, by T. C. Baker,' from whose paper the following data have been taken: The mineralization of the district was effected in the Tertiary period, following the intrusions and preceding the appearance of the flows. The area within which productive veins have been found is 1 mile long by 1/2 mile wide. The important units of each of the four general fracture systems meet in the central portion of Proano hill, which is an outcrop of graywacke, and where the rock was also intensely fractured by subsidiary movements, resulting in a shattered zone 1200 ft. long by 400 ft. wide. The mineralization was more intense in the immediate vicinity of the principal channels through which the solutions rose. The valuable metals are silver and gold, the ratio by weight of the former to the latter being 1000 to 1.5. Argentite is the predominant silver mineral, and is associated with pyrite and manganese mineral. The sulfides are primary throughout. A slight secondary action is represented by small quantities of native silver and silver halides, principally cerargyrite, which are found in the upper part of the mine. Oxidation has penetrated with great thoroughness to the lowest horizon so far exposed, this being 420 ft. below the present ground-water level. The shattered mass within the central portion of the hill and near the surface was sufficiently mineralized to produce a large stockwork

Jan 1, 1935

By M. J. GAVEN

COMING over from the plant on the Denver and Rio Grande yesterday afternoon I was an interested listener to a smoking-room conversation that had to do with the experimental plant near Rifle. The people who were talking didn't know me and I didn't know them, but I learned quite a little. I understood that the plant would never operate; that it was not intended to operate; that the "oil trust" would keep it from operating; that our tramway had eaten up all our money and still was not working and would not work; that the plant was run by a bunch of kids, and that the superintendent was probably the biggest kid of the bunch. I plead guilty to the latter. But the people who were talking were misinformed. The plant is producing oil. The first sample of oil that came from our unit at the Bureau of Mines experimental plant at Rifle, Colo., was produced on Sept. 18, the first that came out of the condenser, and it is still coming. This sample of oil may mean to the United States what the first oil produced from the first well meant.

Jan 1, 1926

By P. R. Sahm, T. V. Pruss

Mixtures of fine GaSb and Gds as well as preal-loyed GaSbl,As, powders were hot-pressed at 690°C and 25,000 psi. Dense alloys with compositional gradients of less than 5 pct were obtained from mixtures containing about 20 mol pct GaAs. For x < 0.2, there were increasing compositional gradients, and for x > 0.2 a GaAs-rich second phase appeared in the microstructure. Densification as well as alloying wlechanisms were enhanced by dissociation and, possibly, oxidation reactions of the powders. Densification of coarse prealloyed material, however, primarily depended on plastic flow phenomena and required temperatures just below solidus and pressures of 50,000 psi Thermal and electrical properties were measured. Although in no case was the figure of merit of melt growth materials approached closer than to within 25 pct, the better overall thermoelectric properties were found in coarse-grained, prealloyed materzals which had been compacted to near theoretical density and where grain regrowth had been induced. Similar results are believed to hold in other binary 111-V compound systems if processed under similar conditions. The densification of unalloyed GaSb powders during pressure sintering (= hot pressing) was shown to depend strongly on powder particle size.&apos; Fine powders displayed a "liquid skin effect" that enhanced compaction through the presence of liquid gallium, whereas coarse powders compacted predominantly by plastic flow. The liquid skin effect, in particular, appeared attractive for alloying GaSb with other, higher-melting, III-V compounds, and to densify these in a one-step operation. This is of special interest in the case of III-V compound alloys as the conventional techniques of melt growth or long-time annealing of powders2 is very time-consuming, especially in cases where a large separation of liquidus and solidus can be expected, such as in GaSbl alloys.2 It was felt that experimentation with this system, a particularly unfavorable example, would allow us to extrapolate to several other, more favorable, cases. Uses of Ill-V alloys are most evident in thermoelectric energy conversion devices.&apos; For this reason certain thermal and electrical properties were measured and compared to those of melt-grown material and to hot-pressed prealloyed powders. EXPERIMENTAL PROCEDURE The pressure-sintering apparatus has been previously described.&apos; Using this equipment, both powder mixtures of GaSb with GaAs and prealloyed GaSbl-,As, powders were hot-pressed. The mixtures were pre- pared from cast GaSb and melt-grown GaAs. The prealloyed material was obtained from stoichiometric melts, initially heated to 1200°C in an evacuated quartz ampoule, and then annealed in the solidus-liquidus interval. A typical annealing cycle consisted of a heating to 850°C (1 hr), extended successive annealing at 750°C (65 hr), and slow stepwise cooling (25 hr) to below solidus. The GaSb, GaAs, and GaSbl-,As, materials were ground in a vibrational mill to particle sizes below 500 . A jet mill reduced these further where necessary. Fine powders were analyzed by Coulter counting for their size distribution. Average sizes by volume were calculated from the data. Mixing of the powders, where necessary, was carried out through rapid vibrational motion. The hot-pressing operation consisted of a degassing period of 15 hr, in most cases at 690°C, followed by several hours of compression, normally 25,000 psi at 690°C for powder mixtures and 50,000 psi at 710°C for prealloyed powders. The chemical compositions were confirmed by X-ray fluorescence analysis. To estimate the degree of solid solution achieved, lattice parameters were determined and interpreted according to Vegard&apos;s rule. In addition, optical microscopy helped to correlate the relative amounts of the phases present as well as the degree of porosity to the measured density. To reveal grain boundaries, polished surfaces were etched4 with H 2 O:H 2 O:HCl = 2:l:l. In several cases microscopic concentration gradients were monitored by electron-probe analysis-. RESULTS AND DISCUSSION Alloying and Densification of GaSn-GaAs Powder Mixtures. After preliminary experiments showed that no appreciable alloying took place in mixtures of coarse GaSb (22.5 p) and fine GaAs (2.5 p) powders, hot pressing of mixtures was confined to fine powders only (3.1 and 2.4 p, respectively). Alloying and densification apparently occurred simultaneously with a grain regrowth mechanism which depended on the presence of a liquid phase.&apos; The liquid phase was provided by the dissociation of GasbS particles into liquid gallium and antimony above 555°C. This not only enhanced grain regrowth and densification, as in unalloyed GaSb,&apos; but took on additional importance here for the alloying process. Alloying was speeded up by the resulting liquid-solid interaction as compared to the very slow solid-state diffusion process normally expected at these temperatures.&apos; The results obtained with a series of powder mixtures have been compiled in Table I. It is seen that for mixtures with less than 20 mol pct GaAs, x < 0.2, the compositional ranges increased and for x > 0.2 a GaAs-rich phase and free antimony appeared in the microstructure in sizable amounts.

Jan 1, 1968

By Alexander R. Troiano, Eugene P. Klier

Since the very early work on quenched structures, where the products of the martensite transformation had been recognizedl this transformation has provoked much interest and study. Theoretically it was desirable to account for the extreme changes in physical properties resulting from the formation of martensite, as that information might lead to results of practical importance. Desirable information, therefore, was on the kinetics of transformation from austenite to martensite as well as on the physical constitution of the martensite. It has been known for years that certain steels quenched to room temperature will contain persistent austenite as well as martensite. Other important and now well-established features of the martensite reaction are the Progress of the reaction on cooling only and the independence of Ar" with cooling velocities exceeding the critical velocity. These facts have been experimentally determined by various methods and investigators. Notable among the early investigators were Tammann and Scheill and Wever and Engel.2 Unfor- tunately, all investigators did not fully interpret their results, which, coupled with several investigations that yielde. conflicting resultsl caused a state of confusion that was not clarified until quite recently. X-ray investigations of martensite in steels3-6 indicate it to be a supersaturated solid solution of carbon in alpha iron. This supersaturation is evident from the appearance of a body-centered tetragonal structure with the addition of sufficient carbon. The dimensions of this tetragonal structure are a linear function of the carbon content within the limits of accuracy of the determinations. Slight tempering of tetragonal martensite leads to the destructi,, of the tetragonal structure, which is converted to a body-centered cubic strutture. This phenomenon has precipitated a controversy concerning the nature and mechanism of the tempering of martensite The facts in the case have been outlined by Epstein7 and more recently by Antia, Fletcher, and Cohen.8 The significance of Ar" on theoretical grounds is not clear, however, although considerable study has been devoted to its determination. The precise position of Art&apos; aS a function of carbon content was first stated by Greninger and Troiano9 for steels covering a range of approximately 0.7 to 1.8 per cent carbon. The effect of alloying elements on Ar" has recently been the subject matter of investigation by various methods.

Jan 1, 1945

By Vsevolod Krivobok

THE re-crystallization of metals has been the subject of much scientific investigation, some of which has resulted in a better understanding of this extremely important and interesting phenomenon. Unfortunately, while many have propounded theories of re-crystallization, but a few have presented experimental evidence as to how it takes place. If this can be determined the question, why re-crystallization occurs, may be answered more definitely. Re-crystallization in single phase metals consists of a complete rearrangement and re-sizing of the grains, of which the structure is composed, while the type of structure remains the same. That is to say, if the structure before re-crystallization is composed of a number of polyhedral grains of different shape and size, a particular spot after re-crystallization will be seen to consist of grains in no way different from the original except in size and shape. The re-crystallized grains may be smaller or larger, depending on the treatment received; and, while the re-crystallization may be brought about by means of heat treatment only in passing through a critical range, yet it is common knowledge that single phase metals subjected to cold working are possessed of a tendency toward re-crystallization, even if the heating does not reach critical range. The study of re-crystallization would, of course, be much easier if we had single crystals of any metal as the original material with which to study the phenomenon of re-crystallization, since it would permit the observation of structural changes at what amounts to enormous magnification, by changing the scale of the specimen. In metals of more normal grain size the crystal boundaries introduce complications, but the process, it may be assumed, is essentially the same. Such an opportunity

Jan 2, 1926

By Jay N. Fairbanks, Richard G. Robinson

This paper discusses a computer program and related formulas for fire fighting responses by coal mine personnel. The computer will interpret the mine air analysis, print reports, and provide relevant graphs allowing quick and accurate responses to coal mine fires.

Jan 1, 1983

By E. H. Mohr

At the McGill concentrator of the Nevada Consolidated Copper Co., all flotation operations have been carried out in Forrester cells since November, 1926. In respect to cost of operation, the new cell has proved to be superior to the Callow, which it supplanted, and its incorporation in the flow sheet has resulted in a marked improvement in the metallurgy. Before citing the advantages of the new machine over the old, it should be explained that the Forrester has not only replaced the Callow, but it has made possible the elimination of a number of tables as well. When Callow cells were in use, table concentration preceded flotation. The ball mill pulp was elevated, by means of air lifts, to roughing Wilfley tables situated two floors directly above the flotation floor. On an intermediate floor were additional tables which cleaned the concentrate from those above. The finished table concentrate constituted approximately 60 per cent. of the total mill production, and contained about 40 per cent, of the recovered copper. The table tailings were returned to the classifiers, the overflow from which went to the flotation cells and the oversize to the ball mills. As soon as the Forrester cells were installed, this tabling operation was discontinued. The ball mill pulp now discharges into the classifiers direct, without the intermediate tabling. It was impracticable to ernploy the present flow sheet when Callow cells were in use, for the reason that unless the great,er part of the heavy mineral was first removed, it accumulated on the mats and adversely affected the flotation operation. By tabling ahead of flotation, it was practicable to maintain the concentrator at 10 to 20 per cent. greater capacity (depending up on the pyrite contnt of the ore) than was possible by flotation alone. This was due to the necessity for finer grinding in the latter case. Even though the table conecntrates contained only 6 to 8 per cent&apos;. copper content, the low smelting costs made it advantageous to operate at high mill capacity, at the cost of low grade of product. Standard Section equipment With the old flow sheet, a standard section consisted of four ball mills and classifiers, one air. lift, 20 roughing tables, 10 cleaner tables, 12 primary

Jan 1, 1928

By E. L. Jr. Spain

THE deposits described in this paper occur over much of Wayne County and in the southeast portion of Hardin County, Tennessee, and in the northeast and northwest portions of Mississippi and Alabama respec-tively. The presence of tripoli in this region has been known for some time and descriptions of various occurrences in Tennessee have been made by Jewell1 and Miser2, while Hilgard3, Lowe4 and Logan5 have treated the deposits that occur in the adjacent portions of Alabama and Mississippi, but there has not been a general survey of the entire field summarizing completely the geology of the deposits with respect to their origin and stratigraphic relationships. During 1934, while engaged in surveys of mineral resources through this region for the Tennessee Valley Authority, the writer collected data with this in mind, and has assembled them in this report. He is indebted to H. S. Rankin and N. A. Rose, of the Tennessee Valley Authority Geology Division, for field assistance.

Jan 1, 1936

Apart from the general cooperation received in many quarters, the Unitization Committee desires to make specific acknowledgment to the following individuals for assistance rendered in the study to this time. California.—Committee members: Joseph Jensen, chairman, L. L. Brundred, E. M. Butterworth, H. Norton Johnson, D. B. Myers, W. R. Wardner; others who contributed: C. R. McCollom, F. C. Merritt, E. B. Noble, Ralph Arnold, J. R. Pemberton, Roy R. Morse, T. F. Stipp, John R. Roberts, R. D. Bush, Alexander Anderson, J. A. Taff, F. 0. Martin, J. E. Van Gundy, E. K. Parks, A. C. Rubel, Lew Suverkrop, W. L. McLaine, Gerard Henny, Walter Stalder, Lester C. Uren, Hoyt S. Gale, W. L. Walker. Rocky Mountain.—Fred E. Wood, chairman, J. G. Bartram, C. E. Dobbin, Wilson B. Emery, Charles E. Erdman, R. D. Hawley, E. W. Krampert, Foster Morrell, W. T. Nightingale, K. B. Nowels, C. M. Rath, Earl Shoenfelt, J. W. Steele, E. T. Wilson, J. J. Zorichak. Kansas-Oklahoma.—Committee members: C. E. Beecher, chairman, A. W. Ambrose, R. C. Hauber, Clyde Alexander, R. F. MacArthur, C. R. Swarts, M. M. Valerius, E. H. Griswold, G. 6. Rollin, L. Murray Newman, David L. Trax, Richard K. Huey, Marvin Lee, Harry Johnson; others who contributed: E. A. Carr, Paul S. Ache, K. C. Slater, R. S. McFarland, J. R. McWilliams, Joseph Chalmers, Henry A. Ley, Dorsey IIager, H. C. George, W. K. Whiteford, L. G. E. Bignell, L. E. Smith, George E. Burton. Texas, Louisiana, Arkansas, New Mexico.—Frederic H. Lahee, chairman, Donald C. Barton, C:. E. Beecher, Olin G. Bell, G. E. Campbell, Paul Wagner, John West, Robin Willis, J. M. Forgotson, E. J. Gorman, P. S. Haury, Marvin Lee, C. F. Lytle, L. H. McBee, T. F. Petty, C. C. Pope, F. S. Prout, J. C. Stewart, J. R. Suman, L. P. Teas, W. C. Thompson, A. F. Truex, R. B. Campbell, M. G. Cheney, P. C. Dean, F. W. DeWolf, Dugald Gordon, B. A. Hardey, F. E. Heath, J. F. Lucey, George C. Matson, W. H. Perot, T. W. Pew, W. A. Price, W. A. -Reiter, R. C. Stewart. Eastern United States and Foreign Fields.—H. H. Hill and E. L. Estabrook, chairmen; Dr. Richard Ambronn, Gottingen, Germany; Arthur R. Andrew,

Jan 1, 1930

Herewith are transmitted the joint report of the Treasurer and Finance Committee for 1934 and the reports for the same year of the Chairmen of the following Committees: Admissions, Membership, Papers and Publications, Library, and MINING AND METALLURGY. TO these reports you are referred for details of the year&apos;s activities. Finances.-Income for 1934 from all sources totalled $134,967 com- pared with $121,689 in 1933. The increase is accounted for principally by four items: $6000 increase in initiation fees and dues of new members; $1800 in current dues; $4000 in "back" dues; and $2800 in the sale of publications, including TRANSACTIONS volumes and technical papers in the form of "separates." In passing, it may be remarked that income from back dues during 1935 will be less than in 1934, for the obvious reason that the total amount of dues in arrears has shrunk and consequently there is less to draw from. Income from

Jan 1, 1934

By E. Peters

As in other fields of Extractive Metallurgy, Hydrometallurgy is preoccupied with separation processes and with oxidation-reduction processes. The physical chemistry of each type of process can be described in terms of thermodynamic equilibria and in terms of reaction kinetics. Reaction kinetics are much more important at the low temperatures limiting hydrometallurgical processes than in com- parable pyrometallurgical operations and the number of cases in which the kinetics can be described by simple liquid-phase mass-transfer models are sharply limited. It is convenient to subdivide the applicable rate phenomena into processes in which (a) interface reactions control the rate,(b) mass transfer processes control the rate, (c) solid state process affect the rate, (d) thermodynamically predicted phase changes or molecular reactions fail to take place, (d) metastable substances or supersaturated phases persist, and (elchomogeneous reactions in solution affect the chemistry and the kinetics. Examples are drawn from the unit steps of leaching, cementation, hydrogen reduction, and electrowinning.

Jan 1, 1973

By Olof Löfgren

PART 1 INTRODUCTION All modern pelletizing plants are equipped with either the drum or the disc circuits. Choice of one or the other circuit is not simple and it is desirable to establish a firm basis for such a task. For a meaningful and a fair comparison it is necessary to have the two systems working in parallel in the same plant with the same concentrate under the same supervision. Furthermore, the comparison has to be based on a defined green ball quality and size distribution. BALLING CIRCUITS The LKAB straight grate plant at Malmberget, Sweden, was started up in Septenber 1973. It was designed for a 2.5 Mton annual capacity and was equipped with five balling drum circuits. During the first year of operation it was found that the induration plant had the potential for a higher capacity which required increased balling capacity. For this purpose it was decided to install a balling disc circuit complete with a roll screen. The reasons for selecting a disc were space limitations and LKAB&apos;s desire to gather experience on balling disc circuits. The disc circuit was started up in 1975 and was run in parallel with the balling drums in the same plant and with the same raw material and under the same operating personnel. The necessary conditions for a comparison were thereby fulfilled. The data for the size distribution and quality of the green balls were obtained on random sampling during one year of operation, so that all the variations which appear in a commercial plant are covered.

Jan 1, 1977

By Walter F. Bradley

CLOSE to 300 members and guests were registered at the Regional Meeting of the Institute in San Francisco. Oct. 3-6, and many other mining men were present at some of the sessions, but failed to register. Headquarters were at the Palace Hotel. Technical papers for the Metals Session were sponsored by the San Francisco Section, whereas the program for the Industrial Minerals Session was arranged by the Southern California Section. Walter W. Bradley, Chairman of the San Francisco Section, opened the General and Metals Session, introducing President Buehler, who gave a hearty welcome to those present. Clyde M. Eye, of the. Benguet Consolidated Mining Co., presented the first paper, entitled "The Economic and Strategic Value of Philippine Metals to the United States." In closing, he urged. that this country retain and control the Philippines because their large

Jan 1, 1935

By J. Waldman, M. B. Bever, A. K. Jena

The heats of formation at 273°K of 6 silver-rich Ag-Cd solid solutions and the heat of formation at 78°K of one solid solution have been measured by tin solution calorimetry. The heats of formation are analyzed in terms of the quasichemical theory. If the enthalpy diffel-ence between a hypothetical fcc form and the hcp form of cadmium is taken into account, this analysis does not lead to the conclusion put forth in the literature that electronic effects make significant contributions to the heats of formation of silver-rich Ag-Cd solid solutions. The temperature dependence of the heats of formation is appreciable and negative near 78ºK, but decreases gradually to nearly zero abore 400°K. The relative partial enthalpies per grarn -atom of silver at 541°K and cadmium at 532" and 541°K in tin have also been determined. THE composition range of the silver-rich Ag-Cd solid solutions stable at room temperature extends to about 40 at. pct Cd. Heats of formation of these solid solutions at 308" and 723°K have been measured by solution calorimetry.1,2 Heats of formation for an average temperature of 800°K have also been calculated from vapor pressures.2,3 The heats of formation deviate from the values predicted by the quasichemical theory above about 30 at. pct Cd. This deviation has been attributed to electronic effects at the Brillouin zone boundaries.2 The heats of formation of Ag-Cd alloys are essentially the same at 308", 723", and 800°K; consequently the temperature dependence of the heat of formation d?H/dT = ?Cp is vanishingly small, although from the exothermic heats of formation a negative value would have been expected. In the investigation reported here the heats of formation at 273°K of 6 silver-rich Ag-Cd solid solutions and the heat of formation at 78°K of 1 solid solution have been measured by tin solution calorimetry. The results are analyzed in terms of the quasichemical theory and the dependence of the heats of formation on temperature is discussed. The relative partial enthalpies per gram-atom of silver in tin at 541" and cadmium in tin at 532" and 541°K were obtained in the course of this investigation. The values of the temperature dependence of the relative partial enthalpies per gram-atom of silver in tin derived from the data reported by various investigators2,4-9 are contradictory. The literature contains only a value for 517°K of the relative partial enthalpy per gram-atom of solid cadmium in tin.2 EXPERIMENTAL PROCEDURES Samples of Ag-Cd solid solutions were prepared by melting weighed amounts of silver (99.99 pct pure) and cadmium (99.95 pct pure) in graphite crucibles under a flux of molten potassium chloride.10 The solidified ingots were sealed in evacuated Vycor tubes and annealed at 775°K for 10 days. The ingots were swaged and drawn into wires. The wires, sealed in evacuated Pyrex tubes, were held at 725°K for 5 hr and cooled to 365°K at an average rate of 2.5ºK per hr, followed by furnace cooling to room temperature. Chemical analysis of samples taken from different parts of each ingot gave no indication of segregation. Metallographic examination showed the samples to be homogeneous. Samples of the solid solutions or of the component elements were added to tin-rich baths in a calorimeter." At the start of a run the bath consisted of pure tin. Silver was used in the form of wire of 0.01-in. diam as supplied and cadmium in the form of lumps. Gold (99.999 pct pure) was added with the samples in order to reduce the endothermic heat effect of additions of Ag-Cd solid solutions. Samples of only one composition were added in a run and the ratio of the weight of alloy to that of gold was the same in all additions of a given run. In each run several calibrating additions of tin were made from 273°K. The heat contents of tin were calculated from the following equation, which is based on published data:12 (HTºK- H279º) = 6.70 T - 72,300/T + 20 cal/gram-atom; 505°K < T < 650°K The heat effect of each addition was plotted against the average of the sum of the atom fractions of solutes in the solution before and after that addition. The total concentration of solutes at the end of a run was less than 2 at. pct. In this range the heat effect was a linear function of the atom fraction of the solutes. The heat effect at infinite dilution and the composition dependence of the heat effect were obtained from the plots. RESULTS AND DISCUSSION Evaluation of Data. The linear dependence on composition of the heat effects of additions suggests that in the dilute range the enthalpy interaction coefficients other than the first-order coefficients of silver, cadmium, and gold are negligible, as shown in a concurrent publication.13 The heat effects at infinite dilution and the values of the composition dependence of the heat effects are listed in Table I.

Jan 1, 1970

By Hiroshi Oikawa, A. G. Guy

Recent experimental evidence has shown that it is often incorrect to neglect the reactions occurring at an interface with respect to the diffusion reactions. By introducing reaction-rate constants and k for the transfer of components 1 and 2 between the a and b phases, a phenomenological description has been devised for the coupled processes of diffusion and in-terfacial reaction. An illustrative example has been analyzed with the aid of a suitable computer program. The results indicate that for kab values on the order of 10&apos;1 cm per sec and Ð values of about 10¯10 sq cm per sec, the interfacial reactions are significant during the first 10 2 to l0 6 sec of a diffusion experiment. Among the observable effects of the interfacial reactions in this case appear to be the burying Kirkendall markers and an anomaly in the initial shifting of these markers. THE study of diffusion between two phases is especially important because of its direct connection to phase transformations. For example, the transformation of austenite to ferrite involves diffusion in the a and ý phases and also an interfacial reaction (trans formation) at the a/? interface. If ferrite and aus-tenite are the two members in a diffusion couple, the same two reactions occur during the diffusion process. The numerical values obtained for the diffusion coefficients and interfacial-reaction constants from diffusion experiments can then be employed to predict phase-transformation behavior. Refinement of the calculations of phase transformation is also suggested by the present method for treating two-phase diffusion. In the recent paper by Nolfi et al.&apos; only the solute com ponent is considered in the interfacial reaction accompanying a phase transformation. The present analysis demonstrates that both components must be considered. It is generally recognized that reactions of some kind must occur at the interface in a two-phase diffusion couple, but usually it is assumed that the interface reaction occurs so rapidly that its effect on the overall process is unobservable because the slower diffusion process determines the kinetics of the process. However, Seith and Heumann 2 pointed out that effects of the interfacial reaction should always occur in the early stages of diffusion, and recently Eifert et al. 3 have shown that interfacial reactions influence the composition and motion of the interface in a/ß Al-Cu diffusion couples during the entire course of prolonged, high-temperature treatments. A general procedure for handling the combined processes of interfacial reaction and diffusion in a binary, two-phase system is to introduce kinetic coefficients for the interface reactions and to develop the system of equations governing the interlinked processes of diffusion and interface reaction. The resulting equations, although not amenable to solution in closed form, can be usefully manipulated by a digital computer. INTERFACIAL REACTIONS IN TWO-PHASE DIFFUSION Consider the general case of diffusion between two solid solutions, a and ß, which are adjacent phases in a binary system, Fig. 1. Two semiinfinite bars having compositions c1 and c0ß are jointed at x = 0. If concentrations are expressed in volume fraction,4

Jan 1, 1970

By H. Kenworthy, M. M. Fine

The progress made to date in the mineral dressing of complex Arkansas titanium ores is reported in this paper. Concentrates of rutile, a dioxide of titanium, were produced by treating a submarginal ore from the Magnet Cove Rutile Co., Inc., Magnet, Ark. The rutile recovery at present is 45 to 50 pct of the total TiO2 with the possibility of increased recovery with additional research. The work reported herein is part of a general study which will later include results of investigation of other titanium ore bodies in the Magnet, Ark., area. The fragile character of the rutile minerals, the softness of the gangue, the occurrence of pyrite and leucoxene, and the considerable proportion of extremely small size rutile in the presence of montmorillonite- and illite- type clays in the Magnet Cove open-pit mine are the important factors in the mineral dressing of this submarginal rutile ore.

Jan 1, 1949

By H. M. Howe

THIS paper presents an experimental verification of some of the predictions made by one of us&apos; concerning &apos;the influence of certain conditions of casting upon the size and position of the pipe&apos;, and the position of the segregate, in steel ingots. The predictions which we have been able to verify are the following A. That the pipe is shortened and the segregate raised 1. By slow casting; 2. By casting with the large end up instead of down; 3. By retarding the cooling of the top, e.g., by means of a sinking-head. B. That the pipe is shortened by slow cooling. C. That the pipe and segregate lie in the last freezing-part. Our procedure was to cast ingots of wax (commercially pure stearic acid) containing a little bright green copper oleate (usually 1.5 per cent.) under varying conditions; to saw each ingot open along a longitudinal plane passing through its axis ; and to examine the longitudinal section thus laid bare. In order to make the segregate or enriched part more distinct in color from the impoverished part, a very little red cerasine was added. An experiment which will be described later showed that the cerasine itself does not segregate markedly, if at all. Hence we may assume that the strong contrasts between the green and red shown in so many of our ingots are due, not to segregation of cerasine, but to that of the green oleate, in the wax which in itself is uniformly reddened with cerasine.

Jul 1, 1907