Search Documents

By Frank C. Greene

Drilling in Missouri in 1943 continued at a lower rate than in 1942, only 28 wells being completed. Following the completion of the Cities Service Oil Company's No. I Jim Cook near Tarkio, in the northwest corner, NW. 'fi sec. 32, T. 65 N., R. 39, W., Atchison County, four dry holes were drilled by other parties, all a mile or more from the Cook well. Later the Cities Service Oil Co, completed No. 2 Cook for 60 bbl. Table I gives a summary of activities by counties. The total footage drilled was 23,83134 ft., of which 12,802 1/2 ft. was by cable tools and 11,029 by rotary. Four of the dry holes were drilled into Mississippian or older beds.

Jan 1, 1944

By Frank C. Greene

Drilling in Missouri in 1943 continued at a lower rate than in 1942, only 28 wells being completed. Following the completion of the Cities Service Oil Company's No. I Jim Cook near Tarkio, in the northwest corner, NW. 'fi sec. 32, T. 65 N., R. 39, W., Atchison County, four dry holes were drilled by other parties, all a mile or more from the Cook well. Later the Cities Service Oil Co, completed No. 2 Cook for 60 bbl. Table I gives a summary of activities by counties. The total footage drilled was 23,83134 ft., of which 12,802 1/2 ft. was by cable tools and 11,029 by rotary. Four of the dry holes were drilled into Mississippian or older beds.

Jan 1, 1944

By Walter Bradley

MINING by hydraulic process of the important gold-bearing gravels of the Sacramento Valley in the basins of the Yuba, Bear and American rivers began in 1853, and continued at an ever-increasing rate for 30 years. In its most active days it reached an annual production of $15,000,000, and averaged $10,000,000 per year over the 30 years. During that period no provisions were made to prevent the debris from being dis-charged into the water courses, and ultimately large quantities of silt, sand and gravel were washed down to the lower valleys; filling channels, causing overflow of agricultural lands and difficulty in maintaining navigable depths in the Sacramento River. Agitation and suits filed because of these damages finally resulted in the injunction decision of Judge L. B. Sawyer,1 in the U.S. Circuit Court, Jan. 23, 1884, which closed down practically all hydraulic mining operations not having means to restrain their debris. In 1893 (approved March 1, 1893), Congress passed the act introduced by Representative Anthony Caminetti, of California, creating the California Debris Com-mission, composed of three officers assigned from the Engineer Corps of the U.S. Army, and since that time it has been legal and possible within the drainage systems of Sacramento and San Joaquin rivers to conduct hydraulic mining of gold-bearing gravels behind dams built under this commission's permit and supervision. In the watersheds of the Trinity and Klamath rivers, which flow directly to the Pacific Ocean and do not affect navigation or agriculture, operating permits from the California Debris Commission are not required. There is a measure of restriction there, however,. through what is known as the Trinity and Klamath River Fish and Game Dis-trict. Chap. 215, Stat. 1931, in order to secure relatively clear water for the fishing season, provides that between July 15 and October 15 each year there must not be discharged into these rivers debris that will cause a turbidity greater than a content of 50 parts per million in the

Jan 1, 1936

By executive order of the President, dated June 25, 1918, the investigation of matters relating to gas warfare, which had been initiated by the Director of the U. S. Bureau of Mines early in 1917, and had been continuously maintained and improved since, that time, was transferred to the recently created Division of Gas Warfare of the War Department. On the occasion of this transfer, both the President and the Secretary of War took occasion to speak most highly of the efficient service that had been rendered by the Bureau of Mines. It gives us great pleasure to reproduce here a letter from the President and from the Secretary of War, bearing on this subject and also to append a brief review of the work of the Bureau of Mines, prepared by its Director, Mr. Van H. Manning. The White House, Washington. June 26, 1918. MY DEAR MR. MANNING: I have had before me for some days the-question presented by the Secretary of War involving the transfer of the chemical section established by you at the American University from the Bureau of Mines to the newly organized Division-of Gas Warfare in which the War Department is now concentrating all the various facilities for offensive and defensive gas operations. I am satisfied that a more efficient organization can he effected by having these various activities under one direction and control, and my hesitation about acting in the matter has grown only out of a reluctance to take away from the Bureau of Mines a piece of work which thus far it has so effectively performed. The Secretary of War has assured me of his own recognition of the splendid work you have been able to do, and I am taking the liberty of enclosing a letter which I have received from him, in order that you may-see how fully the War Department recognizes the value of the services. I am to-day signing the order directing the transfer. I want, however, to express to you my own-appreciation of the fine and helpful piece of work which you-have-done, and to. say that this sort of team work by the bureaus outside of the direct war-making agency is one of the cheering and gratifying evidences of the way our official forces are inspired by the presence of a great national task. Cordially yours, Dr. Van. H. Manning, WOODROW WILSON. Chief, Bureau of Mines, Department of the Interior. War Department, Washington, June 25, 1918. MY DEAR MR. PRESIDENT: In connection with the proposed transfer of the chemical section at. American University from the Bureau of Mines to the newly constituted and consolidated Gas Service of the War Department, which you are considering, I am specially concerned to have you know how much the War Department appreciates the splendid services which have been rendered to the country and to the Army by the Department of the Interior, and especially by the Bureau of Mines under the direction of Dr. Manning. In the early days of preparation and organization, Dr. Manning's contact with scientific men throughout the country was indispensably valuable. He was able to summon from the universities and the technical laboratories of the country men of the highest quality and to inspire them with enthusiastic zeal in attacking new and difficult problems which had to be solved with the utmost speed. I do not see how the work could have been better done than he did it, and the present suggestion that the section now pass under the direction and control of the War Department grows out of the fact that the whole subject of gas warfare has assumed a fresh pressure and intensity, and the director of it must have the widest control so as to be able to use the resources at his command in the most effective way possible. The proposal does not involve the disruption of the fine group of scientific men Dr. Manning has brought together, but merely their transfer to General Sibert's direction. Respectfully yours, NEWTON D. BAKER.

Jan 9, 1918

By John Jermain Porter

The chief purpose of this paper is to indicate the laws governing the fuel-economy of the cupola, to examine the feasibility of some of the proposals for increasing its fuel-economy, and to show that the conditions limiting fuel-economy here are altogether different from those prevailing in the blast-furnace. The two methods available for studying the thermal efficiency of the cupola and determining the factors limiting fuel-economy are: 1, by the determination of the total heat-balance; and 2, by the application of the theory of critical temperatures. The case selected as an example represents a cupola operating under fairly efficient conditions. The data are as follows : Cupola, GO in. in diameter, 15 ft. high to the charging-door, with a 9-in. lining. Bed-charge, 2,000 lb. of coke and 4,000 lb. of iron. Subsequent charges, 400 lb. of coke and 4,000 Ib. of iron. Total number of charges, 20. There was 800 lb. of coke recovered from the drop, hence the total coke burned is 8,800 lb., or 0.11 lb. of coke per Ib. of iron. Coke contains 90 per cent. of fixed carbon and 2 per cent. of moisture. 300 1b. of kindling-wood is used in lighting. 80 lb. of limestone (95 per cent. of CaCO,) is used per charge, or 0.02 lb. per Ib. of iron. Melting-loss, 4 per cent.; distributed thus : Fe, 3.5; Si, 0.25; Mn, 0.25 per cent. Average analysis of top-gases : CO2, 15.1; CO, 10.0 per cent. Average temperature of top-gases, 1,600" F. Temperature of air and stock charged, 60" F. Dew-point of air, 50 F. The items entering into the total heat-balance and their calculation are as follows: 1. Heat of combustion of fuel.—Total heat evolved = 14,580 x lb. of carbon burned + 7,200 X Ib. of wood burned. Hence B.t.u. per lb. of iron charged =

Jan 1, 1913

By K. C. Gilbart, E. Stansfield

This test was described in a privately circulated First Progress Report on Slacking Characteristics of Coal, by A. C. Fieldner and W. A. Selvig, May 1, 1928. The test was described in detail in U. S. Bureau of Mines Report of Investigation 3055, in November, 1930,1 The test, in brief, is conducted as follows: A sample of freshly mined coal consisting of 18 to 25 pieces approximating 1 1/4 cubes, and weighing 500 to 600 grams, is taken for the test. The sample is subjected to a "blank sieving" of carefully regulated degree, on an 8-in. circular sieve with 0.263-in. square openings, and the undersize and oversize weighed. The oversize is placed on a sheet-iron pan and dried for about 24 hr. in an A.S.T.M. air-drying oven maintained at 30" to 35" C. through which a current of warm air is drawn. The sample is then cooled to room temperature and immersed for one hour in water at the same temperature. The water is then drained off, the sample dried for 24 hr. as before, cooled, sieved as before, and the oversize and undersize weighed. The percentage weight of the undersize is calculated and reported as the first cycle loss. This loss, corrected by subtracting the percentage loss in the blank sieving, is termed the slacking index. The sample may be subjected to further cycles of wetting, draining, air-drying, sieving and weighing. In a letter (August, 1932) W. A. Selvig approved making the blank sieving on a duplicate sample, rather than on the sample used for the test, where sufficient coal was available. This method is now employed in these laboratories. The accelerated weathering test has been employed in the laboratories of the Research Council of Alberta, at Edmonton, since 1928, but not found entirely satisfactory as repeat determinations with samples taken from the same or adjacent mines frequently showed serious differences. Differences must be expected as the coal may vary in the seam, and the selection of a typical set of lumps approximating 1 1/4-in. cubes

Jan 1, 1934

By Glenn A. Keep

THIS paper is not an announcement of the successful conclusion of the Cerro de Pasco Copper Corporation's pacos-pyrite problems, but merely a description of the commercial-scale, intermittent-roasting operations conducted by the writer, J. H. Lucas and others of the staff. It was prepared by request, for presentation at the February meeting of the Institute. The results obtained in Peru confirm the 1-ton-a-day experiments completed about three years ago at Kearny, N. J. by C. C. Gordon and Mr. Lucas, where it was first demonstrated that a mixture of about 80 per cent. pacos ore with 10 per cent. pyrite ore and 10 per cent. salt could be roasted intermittently in a small 1-ton-a-day Holt-Dern furnace without extraneous fuel, producing porous calcine that could be leached rapidly. Mr. Keep and his staff, by successfully introducing improvements in the construction of the commercial furnace and in their handling of material, have established beyond doubt a low cost for roasting. The other steps in the process of treating pacos and pyrite ores have not as yet been demonstrated as sufficiently conclusive to warrant their acceptance for a permanent plant. Cerro de Pasco Ores The ores of the Cerro de Pasco Copper Corpn. at Cerro de Pasco, Peru, are situated at an altitude of 14,000 ft. The town and mines are served by the Cerro de Pasco Railroad, which operates between Cerro de Pasco and Oroya, the site of the company's copper and lead smelters. Table 1.—Average Analysis of Cerro de Pasco Ores Pacos Ore Pykite Ore Silver, oz............................................... 10.3 12.0 Gold, oz................................................ 0.007 0.01 Lead, per cent........................................... 1.7 1.8 Copper, per cent......................................... 0.19 0.27 Zinc, per. cent........................................... 1.4 1.02 Iron, per cent........................................... 13.4 34.45 Silica, percent.......................................... 61.8 24.5 Alumina, per cent....................................... 2.5 0.62 Lime, per cent........................................... 1.5 0.20 Manganese, per cent..................................... 0.42 0.09 Sulfur, per cent,.......................................... 1.1 34.2

Jan 1, 1929

Executive R. C. ALLEN, Chairman ERLE V. DAVELER, Vice-chairman WILDER JUDSON R. M. ROOSEVELT G. B. WATERHOUSE Finance H. G. MOULTON, Chairman HENRY KRUMB PAUL D. MERICA H. T. HAMILTON, Consultant Admissions W. B. HEROY, Chairman GEORGE D. BARRON, Vice-chairman H. T. HAMILTON PHILIP KRAFT W. A. SINSHEIMER

Jan 1, 1937

By Jacob T. Wainwright

This stove has been designed to meet the requirements of a fur nave that must be operated with either a reducing or a neutral flame ; and more particularly to make feasible the operating of re duction-furnaces with the cheaper grades of gas-fuel, which has heretofore been impracticable. In general, cheap gas-fuels result from incomplete combustion, and, being suited for further combustion, answer very well for heat ing purposes; and high temperatures may be attained with them, when they are used in conjunction with regenerative stoves. But, in operating a reduction-furnace, a high temperature is not the only requirement. It is also necessary that the fuel shall not be cansumed beyond a certain degree, in order to insure a re ducing flame for the reduction-process ; consequently, it becomes necessary to dispense with combustion as much as possible previous to the use of the fuel-gases in the reduction-furnace. Moreover, these gases must be preheated to a high degree, in order that a sufficient temperature may be maintained in the furnace; and, since this preheating cannot be accomplished by a previous, partial combustion of the gases themselves, it follows that the stoves for pre heating these gases should be heated to as high degree as it is pos sible to attain with an inferior fuel. This result can best be accom plished by complete combustion of the heating gases, and is further facilitated by preheating all of the air and gas used for this com plete combustion. It is more particularly desirable to preheat the air, since the combustible gases used may generally be obtained directly from the furnace, or gas-producer. The reducing gases, escaping from a gas-fuel reduction-furnace, are capable of considerable further dilution with air to secure com plete combustion, and consequently may be utilized for heating the stove to a high temperature, provided the air be sufficiently preheated.

Jan 1, 1889

By W. Luyken

A NUMBER of articles have been published, notably those by R. S. Handy, R. T. Hancock and A. P. Watt in Engineering and Mining Journal, dealing with the calculations involved in ore dressing.. These publications demonstrate both, the importance of the subject and the lack of success in developing a generally recognized method for comparing enrichment effects. Considering that we may wish -to compare enrichment results on similar or dissimilar ores, that we may desire to make the comparison on the basis of either the absolute or the economical efficiency, and that the number of factors upon which the result depends is large, the question arises whether it is possible to set up a positive method for such calculations. In the following pages it is our aim to show that a sure, complete and successful way to overcome existing difficulties has been found. GRAPHICAL ANALYSIS OF ORE-DRESSING PROCESSES The following is from Truscott's Text Book of Ore Dressing (London, 1923) x = assay of ore treated (feed). y = assay value of the concentrate. z = assay value of the tailing. a = weight of feed. b = weight of concentrate. c = weight of tailing. C = fractional concentration = b/a= x-z/y-z (1) K = ratio of concentration = 1/C = a/b =y-z/x-z (2) R = fractional recovery = yb/xa = Cy/x. (3) 100R = percentage recovery. Copt = theoretically best concentration. 100 - Copt = waste in the feed.

Jan 1, 1929

By Frederick Prime

In this second supplementary list no titles to which an * is pre fixed hare been seen by tlie compiler; and he will be most thankful to have any omiesisne or inaccuracies in the list sent to hiin to be ptiblisi~cd as a third supplement in the next volume of the actiotra. The author is indebted to Prof. J. J. Stevenson, of New Tork, Prof. P. R. Uhlcr and John 'CV. M. Lee, Esq., of Balti more, and Lloyd P. Smith, Esq., of Philadelphia, for valuable assistance. office, allkntorn iron compaxy, 30 South Third Street, Philadelphia, September 5th, 1881. Alabama. Geologiml Survcy of Alabama. report of Progress for 1879 and 1880, by Eugene A. Smith, State Geologist. Montgomery, 1881. 8vo., 158 pp., and 2 maps. California. Omit Report of Hon. T. Butler Ring, iu sopplemeut I. For Trask's Geology and Illdustrial honrecp, etc., in Supplenlvut I., read Tyson's, etc. Fremont's Menloir on Upper Califijrnia, is also published as XXXth Congress, lat Session. Senate Ms. Doc., No 148, and has a map. For Randall's Report in Supplement I, rend Report of the Special Committee in favor of a Geological Snrvey, subrn-itted by Mr. Randall, April 24th, 1861. n.d., 1851. 8cWo., 19 yp. XXXIst Congress, 1st Session, Sen. Ex. Doc., No. 47, Part 2 [Part 1 is Tyson's Report.) RejW of the Secretary of War in further compliance with the Resolution of the Senate?, calling for Colbies of

Jan 1, 1881

By Y. C. Liu, R. H. Richman

The effects of gel,manium and tin on the deformation and 9-e-crystallization textures of copper have been explored in detail with in the copper-rich terminal solid solutions. Addition of solute to copper produces a change in deformation texture from the copper type to the 70 :30 brass type. This transition has been measured quantitatively The types mid proportions of recrystal-lization components have been determined as a function of com-position, and correlation of recrystallization components with specific deformation components is discussed. On the basis of information available in the literature, it has been suggested that the effect of solute elements on the recrystallization texture of copper

Jan 1, 1961

By A. A. Burr, D. Caplan

IN carrying out experiments in metal-gas systems, it is often difficult to estimate how long a reaction period must be allowed for equilibration. This is especially true in systems for which the diffusion coefficient is not known. In an investigation of the Cr-O system, the necessary information was obtained in the way described subsequently. Two pieces of chromium sheet of different thicknesses were packed in mixed powders of chromium and Cr2O3 and sealed into an evacuated metal capsule by welding. Austenitic stainless steel proved suitable as a capsule material up to 1350°C and molybdenum at higher temperatures. The capsule then was heated at a specific temperature for a time sufficient to saturate with oxygen the thinner but not the thicker specimen. The time is readily estimated from a preliminary experiment if a sufficient thickness differential is chosen. Under these experimental conditions, the metal sheet is exposed to a partial pressure of oxygen equal to that of the dissociation pressure of the oxide and hence can become saturated with oxygen without developing any second phase. After cooling, both samples were analyzed for oxygen by the vacuum fusion technique. Assuming that the surface of the specimens is kept saturated with oxygen throughout the experiment, the diffusivity can be calculated by application of the appropriate solution to Fick's second law. This is most conveniently accomplished by use of a plot of mean fractional saturation (Cm-Co) / (Cs-Co) vs (Dt) ½/L as given by Darken,' where t is time, L the half-thickness of the sheet, and D the diffusion coefficient. Cm, the mean concentration at time t, is given by the oxygen percentage in the thicker specimen; Cs, the constant surface concentration, is the oxygen percentage in the thinner specimen; Co is the oxygen content of the original chromium sheet. (Cm-Co) / (Cs-Co) is calculated and the corresponding (Dt) ½/L is read from the graph and D thereby calculated. By performing the experiment at two temperatures and plotting log D vs 1/T, the D for any temperature is established. (The activation energy for diffusion may be obtained from the slope of the line.) Once D is known as a function of temperature, it is a simple matter to estimate the correct reaction time for experiments with single specimens at other temperatures by equating (Dt) ½/L to its value for effective saturation. Darken' points out that this is approximately unity. The solubility of oxygen in chromium, as determined from the thin samples at each temperature, proved to be approximately 0.03 pct at 1350°C and less at lower temperatures. Due to low solubility and to the known difficulties of the vacuum fusion method in this low range, the values obtained for D (5x10-0 sq cm per sec at 1350°C) are estimated to be correct only within an order of magnitude. Nevertheless, the method has proved useful in estimating reaction times. Its usefulness will be greater in metal-gas systems where the solubility is appreciable. A second function of the method is to permit the determination of diffusion coefficients in systems for which the conventional techniques are experimentally difficult or impossible.

Jan 1, 1956

By F. Weinberg

The relative concentration of 1" at grain boundaries in controlled orientation bicrystals has been examined by autoradiographic techniques, and by activity measurements of grain boundary surfaces exposed by preferential ,melting. The autoradio-graphs indicate that thallium is concentrated at grain boundaries in as-grown bicrystals, but not in zcell-annealed bicrystals. They also indicate that the solute concentration and the distribution on as-grown bicrystal surfaces are markedly different than that of the bulk material. The boundary surface measurements are in agreement with the autovadiographic evidence. On the basis of these measurements, as-grown bicrystals containing approximately 100 ppm of Tl, solidified at rates between 5 and 30 cm per hr and with tilt boundaries greater than 10 deg, exhibited grain boundary segregation equivalent to roughly 10 atomic planes of pure solute. Higher solute concentrations (equivalent to 140 atomic planes of pure solute) were obtained in bicrystals solidified slowly (0.6 cm per hr); slightly higher values were obtained in specimens containing a large angle nantilt boundary. Annealing for various times over a range of temperatures eliminated grain boundary segregation within the experimental uncertainty of the results (equivalent to 1 atomic Plane of pure thallium at the boundary). The results for the as-grown bicrystals can be qualitatively accounted for by assuming the presence of a groove on the solid-1iq;id interface, at the grain boundary. SOLUTE segregation at grain boundaries may be considered in two parts, namely, nonequilibrium segregation associated with the solidification process, and equilibrium segregation in fully annealed materials.' There is much indirect evidence for nonequilibrium segregation, based on preferential etching at grain boundaries and the mechanical properties of as-cast alloys. In addition, some direct observations have been reported in which radioactive tracers were used as solute additions and segregation detected at the grain boundaries by autoradiographic techniques. However, there is little detailed quantitative data on solute concentrations related to grain boundaries, particularly for different freezing conditions and grain boundary configurations. Equilibrium segregation at grain boundaries has been considered both theoretically and experimentally. cean' has made an estimate of the maximum equilibrium solute concentration that might be expected at a grain boundary, based on the lattice distortions in the boundary region. He arrived at a concentration which was equivalent t a monatomic layer of pure solute. A similar value, based on thermodynamic arguments, was calculated by Cahn and Hilliard for the segregation of phosphorus in iron. Experimentally, much higher values of solute concentration at grain boundaries have been reported recently by both Inman and iler' for phosphorus in iron, and Ainslie et 1.' for sulfur in iron. They observed concentrations equivalent to as much as 20 to 100 atomic layers of pure solute at the grain boundaries. However, in both cases it was shown that the observed segregation was not due solely to equilibrium segregation at the grain boundary. In the former case, precipitation effectss due to trace impurities in the material were believed to account for the large amount of solute present at the grain boundary. In the latter case it was shown that a high density of dislocations in the boundary region could provide a large number of additional sites for solute atoms, other than at the grain boundary. Thomas and chalmera have reported on the equilibrium segregation of po210 in grain boundaries of Pb-5 pct Bi alloys. Using autoradiographic techniques, they observed a concentration of polonium along the boundary trace on the surface of annealed bicrystal specimens grown from the melt. The concentration only appeared after annealing, and varied with boundary angle, increasing as the boundary angle increased. Their conclusions have been questioned by Ward," who pointed out that the segregation they observed along the boundary trace was much too wide to be compatible with the usual concepts of the thickness of a grain boundary of several lattice spacings. Also, Maroun et al.,l1 with specimens similar to those of Thomas and Chalmers, found that segregation could only be detected on the specimen surface, suggesting that Thomas and Chalmers' results were associated with an oxidation effect of polonium, and not equilibrium segregation. Thomas and Chalmers replied12 that they did observed segregation at the grain boundary in the bulk material and suggested further experiments were necessary to resolve the difference. The purpose of the present investigation was to examine both nonequilibrium and equilibrium grain boundary segregation in melt grown bicrystal specimens as a function of boundary angle, growth rate, and solute concentration, and to de-

Jan 1, 1963

By I. J. Hegyi, J. J. Tietjen, H. Nelson, J. I. Pankove

The fabrication of p-n junctions in GaAsl-,P, alloys by a vapor-phase gowth technique has for the first tirne resulted in room-temperature injection lasers capable of operating over a broad range of wavelengths extending into the visible region of the spectrum. The shortest wavelength achieved to date is 6750A at room tetnperature. In addition, at 78°K the threshold current density values for these lasers are generally the lo~vest reported, and the emitted radiation extends to the lozc,est wavelength ever attained (6350A). With lasers fabricated from material containing 14 pct Gap, quanticm efficiencies of 26 pct and peak power outputs of 25 zu were obtained at room temperature. ALTHOUGH room-temperature operation of GaAs injection lasers has been well-documented,&apos;-5 the operation of GaAsl-,P, (x > 0) laser diodes has been restricted to relatively low temperatures.8-&apos;0 This has been previously attributed5, 7, 10-12 partially to the difficulty of preparing single-crystalline GaAsl-& alloys having a high degree of chemical homogeneity and purity. Also, with these materials it has been difficult to prepare high-quality, abrupt p-12 junctions by diffusion techniques; and, in turn, this has made it difficult to obtain optimum electrical properties for room-temperature operationL3 in the resulting laser diodes. As a result, GaAsl-,P, laser diodes have not been efficient enough to permit operation at room temperature. For example, using diffused structures, only a few diodes were obtained which could be operated even close to room temperature (255K)." Recently, a vapor-phase growth method of preparing epitaxial deposits of GaAsl - .P, alloys has been described,14 and the high-purity and homogeneity of these materials has been previously demonstrated. Of special significance, with this technique, n- or p -type doping can be initiated or discontinued at any time and at almost any rate during the crystal growth so that the donor and the acceptor concentrations can be easily controlled to obtain desired impurity profiles. This permits high-quality, abrupt p-TZ junctions to be vapor-phase grown entirely during the crystal growth process, so that diffusion or other p-n junction fabrication processes are unnecessary. After growth, the device does not have to be heated to elevated temperatures, which avoids the possible unwanted introduction and motion of both impurities and lattice defects. Using the vapor-phase growth method cited above, over 300 room-temperature injection lasers have been prepared from GaAsl-,P, alloys having compositions in the range of 0 5 x 5 0.41. These lasers have emitted cohe~ent radiation in the spectral range of 8350 to 6350A at 78°K or from 9000 to 6750A at room temperature. The threshold current densities of the best lasers are independent of the alloy composition over the range 0 < x < 0.2 and compare favorably with values for good GaAs lasers.&apos; MATERIAL PREPARATION Multilayer, epitaxial deposits of GaAsl-,P, alloys are prepared by a vapor-growth technique described elsewhere.14 With this technique, the individual layers which comprise the multilayer structure are prepared sequentially in the deposition apparatus without interrupting the crystal growth. The epitaxial layers are deposited on GaAs substrate surfaces oriented normal to the ( 100) direction. The substrate wafers employed in this study were usually doped with tellurium to an electron concentration of approximately 2 x 10" per cu cm. To avoid strains, the first 10 to 15 p of the deposited material is uniformly graded from pure GaAs to the specific GaAsl- ,P, alloy composition of interest. The GaAsl - ,P, alloy growth is then continued to form a layer of constant composition having a thickness in the range of 25 to 75 p. Both the graded region and the layer of constant composition are doped with selenium to an electron concentration of about 2 x 10" per cu cm. The p region of the diode is then incorporated in the crystal by abruptly changing the dopant concentrations in the vapor phase to facilitate doping with zinc. This layer has a hole concentration of approximately 3 X 1019 per cu cm and typically is 50 p thick. DEVICE FABRICATION In general, the GaAs substrate and the region of graded composition are removed. Ohmic contacts are made to the n-type side by tin evaporation and to the p-type side by an electrodeless nickel deposition. This is followed by an electrodeless deposition of gold on both sides. The crystal wafer is then cleaved along (110) planes and sawed into rectangular parallelepipeds. Typical dimensions are 100 by 300 for the junction area and 100 µ for the diode height. The diodes are either soldered to a copper stud or pressure-mounted in a copper clip. RESULTS AND DISCUSSION Approximately 400 laser diodes having compositions in the range of 0.41 have been prepared by the method described above. Each laser was routinely tested at liquid-nitrogen temperature. The lasers were operated with l-psec current pulses at a repetition rate of 60 pulses per sec. The parameters of greatest practical interest are the photon energy or wavelength of the laser output and the threshold current density. Fig. 1 shows the variation of photon energy with alloy composition at 78°K. The composition was determined from the lattice constant of the material obtained by X-ray back-reflection measurements. Although there

Jan 1, 1968

By Leo Brewer, Gerd M. Rosenblatt

Thermodynamic calculations predict the species vaporizing from metal-oxide mixtures when reliable free energy functions, enthalpies of formation, and dissociation energies are available for the possible gaseous and condensed oxide components. Calculations of the oxygen to metal ratio in the vapor phase compared with the oxygen to metal ratio in a liquid metal saturated with oxide impurity are presented The possibility of purifying metals contaminated with oxide by vacuum melting or by distillation is discussed. Kinetic considerations affecting rates are neglected. IN recent years extensive information has been obtained on the thermodynamic stability of gaseous oxides of metals due to a variety of new types of measurement. Perhaps the greatest amount of information has come from the application of mass spec-trometry to the study of high-temperature vapors.&apos; In many instances oxides of quite unusual oxidation states are found to be important in the high-temperature vapors. At low temperatures the standard free energy change for a reaction as given by the equation ?F° = ?H° - T?S° is determined primarily by the AH" value. However, at higher temperatures where the value of T in the T?S° term is large, the entropy term becomes equal to or greater than the AH term. At low temperatures only reactions for which AH is negative or only slightly endothermic are of importance. This restricts the main equilibrium species largely to those with completed octets or those with the principle oxidation number of the element. At

Jan 1, 1962

By Luis Toron, Salvador Cortes-Obregon

John D. Price (Colorado Fuel and Iron Corp., Pueblo, Colo)—The paper on the coal fields of the Oaxaca district as prepared by engineers Toron and Cortes-Obregon of the staff of the Bank of Mexico bears witness to the thorough and careful way in which the men associated with this organization perform their work. There is little to be added to their paper in way of discussion other than to confirm and amplify some of their statements. Since the only extensive and well-developed field of coking coal lies in the northeastern section of the country adjacent to Sabinas in the state of Coahuila, it follows that blast furnace plants would be located in that same region. Two such plants are now operating at Monterrey and Monclova, using coke produced at the Sabinas district mines. But the nearer of these two plants is 600 miles from Mexico City and even farther from the center of population. Transportation of products from these mills to the market area is therefore expensive, both because of the distance and the difficulty of the terrain over which it must be carried. The development of an integrated steel industry closer to the center of population has therefore long been a goal toward which the Mexican technicians have been striving. While the presence of coal of some grade has been reported in many of the states, and many ideas have been advanced regarding its possible uses in iron and steel production, deposits of anthracite in Sonora and the various coals of the Oaxaca district as reported on in this paper are the only ones that have been explored in a serious manner. The coking coal from the Mix-tepec zone appears to offer promise of producing a coke which could be used in a standard blast furnace. Several problems are indicated, however: 1—The ash in the coal is high as mined, but indications are that it can be washed to an ash content of 15 pct with a recovery of 70 pct of washed coal. 2—Such washing would increase the volatile content from 17.4 pct to about 20 pct, and in a byproduct oven this should give a coke yield of close to 80 pct with an ash content of coke under 20 pct. 3—A free swelling index of 5 appears low for a good coking coal, and below that of the coals from the Sabinas district, which show between 6 and 9. But washing of the coal should result in an improvement in this regard; in the United States coals from Utah with an index even lower than 5 have made a usable coke. 4—A coal with volatile as low as 17.4 in raw coal and 20 in washed coal would come close to being classed as a low-volatile rather than medium-volatile coal, and low-volatile coals are notorious for their high expansion properties. Several plants in the United States are making coke from straight medium-volatile coal of 26 to 28 volatile content, and one at Rosita,, Mexico, from coal of 25 volatile. But no plants to my knowledge are using coal as low as 20 volatile. Since the Rosita coal appears to be a borderline coal from the angle of its expansion properties the coking of one of the straight lower volatile must be approached with caution. 5—There are few coals possessing any degree of coking properties which cannot be used in coke production by careful attention to its preparation and blending. The fact that coals of other types are available in this same region make improvement through blending very possible. 6—There are other workable methods of reducing iron ore other than the conventional coke-blast-furnace method. These will not be discussed here but it is known that their use has been considered. The technicians of not only Mexico but also of the other Latin American countries are keenly aware of their natural resources and their national needs. This paper emphasizes the fact that the Mexican technicians are working on their problem and attempting to speed the day of self-sufficiency for their country. Salvatore Cortes-Obregon (author&apos;s reply)—I wish to thank Mr. Price for his kind remarks. The Mixtepec coal as shown in Table II has 30 pct ash and a free swelling index of 5, but when the same coal is washed to 15 pct ash it has a free swelling index of 8 to 9 and the volatiles increased from 17.4 to 20.7 pct. A satisfactory coke has been produced from blends made in the Mexican laboratory using at least 40 pct of the Mixtepec coking coals with the other Oaxaca non-coking coals. Koppers in Germany report good coke obtained from the Oaxaca coal with a blend of 80 pct Mixtepec coal. Consideration is being given the possibility of using methods other than the conventional blast furnace for the reduction of iron ore near the Oaxaca area; electric furnaces appear promising. The non-coking coals could be used to produce cheap electric energy and the coking coals to make metallurgical coke.

Jan 1, 1955

By Morris Cohen

STAFF: Editor, Gerhard Derge Acting Editor, Paul G. Shewmon Carnegie Institute of Technology Schenley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Karl L. Fetters, President; J.S. Smart, Jr., Past-President; R. C. Cole, Vice President; R. L. Hennebach, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: W. O. Phil-brook, Chairman; H. L. Bishop, R. C. Cole, J. N. Hobstetter, W. A. Krivsky, E. R. Morgan, F. C. Langenberg, R. E. Lund, Paul Queneau, L. L. Seigle, R. L. Smith, and T. V. Wainwright. Review and selection of manuscripts is under the supervision of the following Publicotions Committes: Extractive Metallurgy Division: R. E. Lund, Chairman; M. E. Wadsworth, Vice Chairman; D. H. Baker, Jr., G. M. Bell, R. E. Grace, W. A. Krivsky, R. A. Lewis, Charles O&apos;Neill, A. W. Schlechten, R. E. Shinkoskey, and W. W. Stephens. Iran and Steel Division: T. V. Wainright, Choirman; H. L. Bishop, R. E. Boni, T. E. Dancy, D. W. Murphy, Johannes M. Uys, J. B. Wogstoff, and R. G. Ward. Institute of Metals Division: J. N. Hobstetter, Chairman; P. A. Beck, J. J. Becker, G. F. Bolling, J. 0. Brittain, J. B. Clark, R. S. Davis, A. E. Dwight, R. W. Fountain, L. R. Girifolco, J. C. Gurland, H. S. Kalish, E. L. Harmon, J. J. Heger, A. A. Hendrickson, L. Himmel, J. P. Hirth, H. H. Johnson, Jr., R. R. Nosh, T. N. Rhodin, R. H. Richman, H. C. Rogers, W. Rostoker, C. Sherby, C. W. Spencer, L. Slifkin, J. K. Stanley, R. Steinitz, H. C. Stumpf, and R. Swalin. Published bimonthly by the Americon Institute of Mining, Metallurgicol, and Petroleum Engineers, Inc., 345 East 47th Street, New York 17, N. Y. Telephone PLaza 2-6800. Subscription $30 peryear for non-AIME members in United States and North, South, and Centrol America; $32, foreign; $30per$7.50 for AlME members. Single copies, $6.00, single copies foreign, $6.50. The AlME is not responsible for any stotement made or opinion expressed in its publications ... Copyright 1962 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AlME New York . . . Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts . . . Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 224, Number 4.

Jan 1, 1962

By E. T. Turkdogan, P. Grieveson

STAFF: Editor, Gerhard Derge Acting Editor, Paul G. Shewmon Carnegie lnstitute of Technology Sc hen ley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Karl L. Fetters, President; J.S. Smart, Jr., Past-President; R. C. Cole, Vice President; R. L. Hennebach, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: W. 0. Phil-brook, Chairman; H. L. Bishop, R. C. Cole, J. N. Hobstetter, W. A. Krivsky, E. R. Morgan, F. C. Langenberg, R. E. Lund, Paul Queneau, L. L. Seigle, R. L. Smith, and T. &apos;4. Wainwright. Review and selection of manuscripts is under the supervision of the following Publications Committes: Extractive Metallurgy Division: R. E. Lund, Chatrmon; M. E. Wodsworth, Vice Chairman; D. H. Baker, Jr., G. M. Bell, R. E. Groce, W. A. Krivsky, R. A. Lewls, Charles O&apos;Neill, A. W. Schlechten, R. E. Shinkoskey, and W. W. Stephens. Iron and Steel Division: T. V. Wainright, Choirman; H. L. Bishop, R. E. Boni, T. E. Dancy, C. W. Murphy, Johonnes M. Uys, J. B. Wagstaff, and R. G. Ward. lnstitute of Metols Division: J. N. Hobstetter, Chairman; P. A. Beck, J. J. Becker, G. F. Bolling, J. O. Brittain, J. 8. Clark, R. S. Davis, A. E. Dwight, R. W. Fountain, L. R. Girifalco, J. C. Gurland, H. S. Kclish, E. L. Harmon, J. J. Heger, A. A. Hendrickson, L. Himmel, J. P. Hirth, H. H. Johnson, Jr., R. R. Nosh, T. N. Rhodin, R. H. Richman, H. C. Rogers, W. Rostoker, C. Sherby, C. W. Spencer, L. Slifkin, J. K. Stanley, R. Steinitz, H. C. Stumpf, and R. Swolin. Published bimonthly by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc., 345 East 47th Street, New York 17. N. Y. Telephone PLaza 2-6800. Subscription $30 per year for non-AIME members in United States and North, South, and Central America; $32, foreign; $7.50 for AlME members. Single copies, $6.00, single copies foreign, $6.50. The AlME is not responsible for any statement made or opinion expressed in its publications ... Copyright 1962 by the American lnstitute of Mining, Metollurgical. and Petroleum Engineers. Inc. . . . Registered cable address, AlME New York . . . Indexed in Engineering Index, lndustriol Arts Index, and Chemical Abstracts . . . Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 224, Number 6.

Jan 1, 1962

By G. V. Kurdjumou

STAFF: Editor, Gerhard Derge Acting Editor, Paul G. Shewmon Carnegie Institute of Technology Schenley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Karl L. Fetters, President; J. S. Smart, Jr., Past-President; R. C. Cole, Vice President; R. L. Hennebach, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: W. 0. Phil-brook, Chairman; H. L. Bishop, R. C. Cole, J. N. Hobstetter, W. A. Krivsky, E. R. Morgan, F. C. Langenberg, R. E. Lund, Paul Queneau, L. L. Seigle, R. L. Smith, and T. V. Wainwright. Review and selection of manuscripts is under the supervision of the following Publications Committes: Extractive Metallurgy Division: R. E. Lund, Choirmon; M. E. Wodsworth, Vice Choirmon; D. H. Boker, Jr., G. M. Bell, R. E. Grace, W. A. Krivsky, R. A. Lewis, Chorles O&apos;Neill, A. W. Schlechten, R. E. Shinko~ke~, and W. W. Stephens. Iron and Steel Division: T, V. Wainright, Choir- mon; ti. L. Bishop, R. E. Boni, T. E. Doncy, D. W. Murphy, Johonnes M. Uys, J. B. Wogstaff, ond R. G. Word. Institute of Metals Division: J. N. Hobstetter, Choirmon; P. A. Beck, J. J. Beckar, G. F. Boiling, J. O. Brittain, J. 0. Clark, R. 5. Davis, A. E. Dwight, R. W. Fountain, L. R. Girifolco, J. C. Gurlond, H. S. Kolish, E. L. Harmon, J. J. Heger, A. A. Hendrickson, L. Himmel, J. P. Hirth, H. H. Johnson, Jr., R. R. Nosh, T. N. Rhodin, R. H. Richrnon, H. C. Rogers, W. Rostoker, O. Sherby, C. W. Spencer, L. Slifkin, J. K. Stanley, R. Steinitz, H. C. Stumpf, ond R. Swolin. PuUlished bimonthly by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc., 345 East 47th Street, New York 17, N. Y. Telephone PLaZa 2-6800. Subscription $30 peryear for non-AIME members in United States and North, South, and Central America; $32, foreign; $30peryear$7.50 for AIME members. Single copies, $6.00, single copies foreign, $6.50. The CentralAmerica;AlME is not responsible for any statement made or opinion expressed in its publications ... Copyright 1962 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . .Copyright.Registered cable address, AIME New York . . . Indexed in Engineering Index, Industrial Arts Index, and Chemical cableaddres .. . AlME class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 224, Number 3.

Jan 1, 1962