Search Documents

By M. L. Fuller

DURING the last several years many papers have appeared dealing with the structure of highly polished metal surfaces. The awakening of interest in this subject is due to the applicability of the electron diffrac-tion technique to the study of surfaces. The original theory of Beilby1 considered the surface of polished metals as of the nature of a super-cooled liquid or a vitreous, amorphous solid. The electron diffraction effects from polished metals have been interpreted by many to be a direct experimental proof of the correctness of the Beilby theory. This inter-pretation has been strongly opposed by others, so that at the present time the subject is in an uncertain and controversial state. In the present paper new, and hitherto unpublished, electron diffrac-tion effects from polished zinc are described. These observations indicate that the polished surface of zinc is crystalline.

Jan 1, 1938

By Dermot M. Ross-Brown

Introduction Slope angles are one of the major factors affecting the shape of the final pit and the location of the walls Due to differences in geology, the optimum slope angles vary from pit to pit and within different parts of the same pit. Indeed, it is not unusual to have different slope angles for the top and bottom portions of the same cross section. The optimization of these slope angles is a major study in itself and this chapter is intended as a general introduction to the subject. It is not intended to be a comprehensive text for the absolute beginner The objective is to put the various aspects of slope stability analysis into relative perspective by describing the vari¬ous analytical techniques available and indicating when each may be most appropriately used References are made to the many excellent texts and papers on slope stability for the reader who does not have a formal training in soil or rock mechanics. In writing this chapter, an assumption has been made that a tentative mining plan has been drawn up, includ¬ing a preliminary estimate of the slope angles. It has also been assumed that all the necessary field and laboratory data has been collected and reduced to a form suitable for input into the stability analyses.

Jan 1, 1979

THE composition and quality of finished steel depend upon selection and proportioning of the raw materials of the charge as well as upon control of furnace practice. This chapter deals only with the raw materials of the basic open-hearth process that are important in determining the composition of the steel or slag. They are the metallic charge, oxygen-bearing materials, fluxes, alloying and deoxidizing additions, and certain refractory materials used for maintenance of bottoms. Other refractories, which may affect the slag composition, are discussed in Chapter 3. Wide variations are possible in the type and composition of charged materials but certain limiting relations among the elements of the charge must be observed. Since the process consists essentially of refining by the oxidation of undesired dements, a balance must be established between the sources of oxygen and the elements in the charge that are subject to oxidation (see Chapters 2 and 7). For example, if it is desired to use a high ratio of blast-furnace hot metal to scrap, it is necessary to add an oxygen-bearing material such as ore or mill scale to eliminate the excess carbon and silicon that are present in the hot metal. An example of the opposite extreme is the use of a metallic charge composed entirely of steel scrap. With this type of charge, it is common practice to substitute burnt lime for limestone as a flux and to charge some carbonaceous material such as coke to avoid an excess of oxygen in relation to the elements of the charge that are subject to oxidation. Elements such as copper and nickel, which are not oxidized or eliminated by, any other reaction, may be introduced into the charge only to the extent to which they are permissible in the finished steel. An example of adjustment of the charge for elements of this type is found in the use of steel scrap high in copper. In this case, metallic components of the charge other than the scrap should be low in copper, or a sufficiently high ratio of pig iron to scrap should be charged to dilute the copper from the

Jan 1, 1951

By F. L. Bosqui

INTRODUCTION The history of the development of gold metallurgy in South Africa is divisible into two periods: That preceding the introduction of the cyanide process on a commercial scale in 1890; and the 24 years intervening between that important event and the present time. The period between the discovery of the banket reefs of the Witwatersrand and the year 1890 was one of phenomenally rapid progress in mining development, but of no special interest to the metallurgist. There were no strikingly original or distinctly local advances in the treatment of gold ores. Californian practice in stamp milling and amalgamation prevailed, in mills ranging in equipment between 5 and 50 stamps, operating within a wide range of efficiency, and under the trying conditions usually en¬countered in a new and isolated field. The somewhat incomplete records of gold output of that period show that in December, 1887, there were 20 producing companies in the Witwatersrand district, of which 10 had mills, the largest being of 20 stamps. The only official record of returns for May, 1887, was that of the Wemmer mine, whose modest achievement with a 5-stamp, mill was 100 tons crushed, producing 887 oz. 3 dwt. of gold. This is interesting in view of the .present-day output of this field, which in 1913 reached 8,430,998 oz. The rapid increase of production during this first period (May, 1887, to January, 1891) is shown by the following summary for the year 1890:1 Total tons crushed 702,828 Number of stamps in operation 1,046 Average number of tons crushed per stamp per day 2.36 Yield of gold, ounces 494,817 Yield per ton, pennyweights 13.36 The stamp duty ranged between 1 ½ and 4 tons per day, according to weight of stamp, fineness of screen, and operating skill available. The prevailing weight of stamp was about 900 lb., and the screen, 900 meshes to the square inch.

Jan 5, 1915

By Walter Crafts

Structural steels containing chromium have become widely used in the last 20 years. In the earlier part of this period the major applications were in chromium-molybdenum aircraft tubing and similar special high-strength steels. During the past 10 years there has been a notable expansion in the use of chromium-bearing steel for structural purposes when welding was utilized for fabrication. The chromium-bearing steels introduced by Saklatwallal (chromium-copper), Kinzel2 (chromium-manganese-silicon), and Schultz3 (chromium-copper) are being extensively used at the present time. General Effects of Chromium Chromium is so widely known for its carbide-forming tendency that its capacity to stabilize oxygen, nitrogen, and phosphorus is often overlooked. In low-carbon steels of the structural type these so-called secondary characteristics become more prominent. For this reason also, chromium in structural steel is definitely a toughening agent. As the carbon content is increased, the more widely known hardening effect becomes more evident. In low-carbon steels chromium increases the notched-bar impact strength substantially. This property persists at subzero temperatures and is utilized for low-temperature service in chromium-copper steel.4 Chromium also reduces any tendency to strain-aging embrittlement. In addition to improving the toughness of steels with the usual impurities, chromium has the specific property of counteracting the brittleness induced by high phosphorus.5,6 In steels low in carbon and alloys, chromium has an almost negligible effect on tensile strength, and a hardening influence is noticeable only in the stronger steels. The ductility of welds adjacent to the base plate is also improved by chromium, both in the range of foolproof welding steels having strengths of less than 80,000 lb. per sq. in. as well as in the higher strength steels.

Jan 1, 1939

By Walter Crafts

Structural steels containing chromium have become widely used in the last 20 years. In the earlier part of this period the major applications were in chromium-molybdenum aircraft tubing and similar special high-strength steels. During the past 10 years there has been a notable expansion in the use of chromium-bearing steel for structural purposes when welding was utilized for fabrication. The chromium-bearing steels introduced by Saklatwallal (chromium-copper), Kinzel2 (chromium-manganese-silicon), and Schultz3 (chromium-copper) are being extensively used at the present time. General Effects of Chromium Chromium is so widely known for its carbide-forming tendency that its capacity to stabilize oxygen, nitrogen, and phosphorus is often overlooked. In low-carbon steels of the structural type these so-called secondary characteristics become more prominent. For this reason also, chromium in structural steel is definitely a toughening agent. As the carbon content is increased, the more widely known hardening effect becomes more evident. In low-carbon steels chromium increases the notched-bar impact strength substantially. This property persists at subzero temperatures and is utilized for low-temperature service in chromium-copper steel.4 Chromium also reduces any tendency to strain-aging embrittlement. In addition to improving the toughness of steels with the usual impurities, chromium has the specific property of counteracting the brittleness induced by high phosphorus.5,6 In steels low in carbon and alloys, chromium has an almost negligible effect on tensile strength, and a hardening influence is noticeable only in the stronger steels. The ductility of welds adjacent to the base plate is also improved by chromium, both in the range of foolproof welding steels having strengths of less than 80,000 lb. per sq. in. as well as in the higher strength steels.

Jan 1, 1939

By R. H. Winn

In this paper a heterogeneous carbonate reservoir is considered as a succession of layers of formations of radically different porosities, permeabilities, water saturations, and rock matrix types; i.e., the heterogeneity is vertical rather than radial to the wellbore. Presumably each layer is more or less homogeneous. To determine the "net oil in place" in this reservoir it is desirable to know the porosity and water saturation of each layer. In addition, the section must be subdivided into that which will produce oil, that which will produce water, and that which will produce little or nothing. In numerous wells drilled in these reservoirs radioactivity surveys, guard electrode surveys, and caliper surveys have been made. These logs have been compared with core analysis data, when available, and the analysis of the surveys compared with production data. This study, still in progress, is intended to provide improved analytical techniques if such are possible. This paper is a progress report on the work. DETERMINATION OF POROSITY The neutron-gamma log has long been recognized as a measure of hydrogen concentration.1,2,3 In reservoirs that are free of clay, shale, or other hydrogen containing matrices, it has been accepted as a measure of porosity.4,5 Empirical methods to relate relative neu-tron-gamma intensity to porosity are often employed." To provide a more precise determination of porosity from the neutron-gamma log each instrument is calibrated immediately prior to each survey by a method which refers all tools to a hydrogenous cylinder. To insure stability a calibration check is made after each survey. These calibration records are printed as an integral part of the log that is recorded in standard counts per second. A detailed description of the calibration procedure is available in the literature.' The procedure employed insures that each Survey is numerically reproducible within the limits of statistical variation. To relate the standard neutron counts per second to porosity and hole size, records were made in test wells constructed of blocks of limestone. The porosities of the blocks were accurately measured and the blocks completely saturated with fresh water. Fig. 1 presents some of the results obtained in these test wells.' The lines shown in Fig. 1 were obtained by deriving an empirical equation relating the 11 points shown so that the relationship may be projected to larger and smaller hole sizes. A detailed description of the tool is available in the literature.' Field tests indicate that the tool is adjacent to the wall of the hole most of the time when the surveys are made in uncased holes drilled with saline muds. In this circumstance porosity may be calculated from Fig. 1 if the hole size is known. When fresh muds that form thick mud cakes are employed, the centralizing effect of the mud cake must be considered and the porosity determination is less reliable. In cased holes the combined effect of variations in hole diameter and the unknown eccentricity of the casing in the hole may make porosity determinations extremely unreliable. In any event, an accurate knowledge of hole size is essen-

Jan 1, 1958

By Joseph S. Malesky

The discovery and development of explosives mark one of the most important findings in the history of civilization. Without explosives our vast economic enterprise concerning the mining of coal, copper, iron, aluminum, and various other ores could not function. Explosives are used in all kinds of construction works, in the razing of old buildings, blasting of trenches, driving of tunnels, and in many other instances common to our everyday life. For these reasons explosives are rightfully referred to as the forerunner of progress. An explosive may be defined as a substance (usually a mixture) that, when flame or shock is applied, yields readily to rapid combustion or oxidation, accompanied by the formation of such relatively large quantities of gases as to produce much violence and pressure which, in turn, react against their surroundings and cause what is termed an explosion. By their very nature the action of explosives is destructive and disruptive of adjacent materials. Decomposition of explosives can occur through deflagration, which is rapid burning or combustion, as in the case of black powder, or through detonation, which is an almost instantaneous disruption, as in the case of dynamites and blasting agents. HISTORY OF BLASTING WITH EXPLOSIVES At one time workmen obtained stone blocks for building by grooving the rock with crude picks, driving wooden wedges into niches in the rock, and pouring water on the wedges; the swelling of the wood forced out the blocks. As late as the 17th century, fires were placed against the face of rock to crack it, and water was sometimes dashed on the heated rock to shatter it by sudden cooling. The progress of our country is synonymous with advancement of the improved manufacture and extended use of explosives. Coal had been

Jan 1, 1981

By W. R. Hibbard

THE classical work on the electrical conductivity of alloys was carried out by Matthiessen and his coworkers1 in the early 1860's. He attempted to correlate the electrical conductivity of alloys with their constitution diagrams, but the information regarding the latter was too meager for success. Guertler2 reworked Matthiessen's and other conductivity data in 1906 on the basis of volume composition (an application of Le Chatelier's principle with implications as to temperature and pressure effects), and obtained the following relationships between specific conductivity and phase diagrams (plotted as volume compositions) : 1—For two-phase regions, electrical conductivity can be considered as a linear function of volume composition, following the law of mixtures. 2—For solid solutions, except intermetallic compounds, the electrical conductivity is lowered by solute additions first very extensively and later more gradually, such that a minimum occurs in systems with complete solid solubility. This minimum forms from a catenary type of curve. Intermetallic compound formation with variable compound composition results in a maximum conductivity at the stoi-chiometric composition. Landauer" has recently considered the resistivity of binary metallic two-phase mixtures on the basis of randomly distributed spherical-shaped regions of two phases having different conductivities. His derivation predicts deviations from the law of mixtures which fit measurements on alloys of 6 systems out of 13 considered. Volency (Ionic Charge) Perhaps the first comprehensive discussion of the electrical resistivity of dilute solid-solution alloys was presented by Norbury' in 1921. He collected sufficient data to show that the change in resistance caused by 1 atomic pct binary solute additions is periodic* in character. The difference between the period and/or the group of the solvent and solute elements could be correlated with the increase in resistance. Linde5-7 determined the electrical resistivity (p) of solid solutions containing up to about 4 atomic pct of various solutes in copper, silver, and gold at several temperatures. He reported that the extrapolated"" increase in resistance per atomic percent addition is a function of the square of the difference in group number of the solute and solvent as follows: ?p= a + K(N-Ng)2 where a and K are empirical constants and N and Ng are group numbers of the constituents. This empirical relation was subsequently rationalized theoretically by Mott,8 who showed that the scattering of conduction electrons is proportional to the square of the scattering charge at lattice sites. Thus, the change in resistance of dilute alloys is propor-t,ional to the square of the difference between the ionic charge (or valence) of the solvent and solute when other factors are neglected. Mott's difficulty in evaluating the volume of the lattice near each atom site where the valency electrons tend to segre-gate: limited his calculations to proportionality relations. Recently, Robinson and Dorn" reconfirmed this relationship for dilute aluminum solid-solution alloys at 20°C, using an effective charge of 2.5 for aluminum. In terms of valence, Linde's equation becomes ?P= {K2 + K1 (Z8 -Za)2} A where K1 and K2 are coefficients, A is atomic percent solute, Z, is valence of solvent, and Zß, is valence of solute. Plots of these data for copper, silver, gold, and aluminum alloys are shown in Fig. 1. The values of K1 and K2 are constant for a given chemical period (P), but vary from period to period. The value of K, increases irregularly with increasing difference between the period of the solvent and solute element (AP), being zero when AP is zero. The value of K, appears to have no obvious periodic relationship. All factors other than valence that affect resistivity are gathered in these coefficients. Because of the nature of the coefficients, Eq. 1 is of limited use in estimating the effects of solute additions on resistivity unless a large amount of experimental data are already available on the systems involved. It is the purpose of the first part of this report to investigate the factors that may be included in the coefficients of Linde's equation. On this basis, it is hoped that the relative effects of solute additions on resistivity can be better estimated from basic data, leading to a more convenient alloy design procedure. It is well 10,11 that phenomena that decrease the perfection of the periodic field in an atomic lattice, such as the introduction of a solute atom or strain due to deformation, will also increase the electrical resistivity. Thus, in an effort to relate changes in electrical resistivity to alloy composition, it appears appropriate to consider the atomic characteristics related to solution and strain hardening

Jan 1, 1955

By H. B. Pulsifer

THE unprecedented high price of zinc ore prevailing through the early months of 1915 caused great activity in the Joplin district of Missouri. The Media mill is conspicuous as one of the first of the new "big mills" of the district. The mill was built over a mine previously worked but abandoned in 1912 because of the leanness of the ore and the large quantity of water encountered. The ore prices prevailing-$100 a ton in June, 1915, as against $50 in 1912-favored the new undertaking. The mill was designed for good recovery so that it might operate in times of depression. In design and equipment, the mill is exclusively local in conception and construction. Former Exploitation The tract of land is a part of the large Guinn holdings; 70 acres are comprised in this particular lot, which is situated just a mile north of the center of Webb City on the Alba line of the Southwest Missouri Electric Railway. The ore lies 242 ft. below the' surface at the top of the knoll which is surrounded by the well-known properties: Black Cat, Ground Floor, Florence, Hurry-Up, Electrical and Mercantile. Since the abandonment, in 1913, of the Yellow Dog. a bit farther to the north, the Black Cat, Ground Floor and Florence workings had been flooded. However, as there was no cut through from this side into the area it was proposed to exploit, it was thought that moderate pumping facilities would take care of the water.

Jan 5, 1917

By B. D. Cullity, A. Freda

It is well known that deformation by cold drawing or swaging produces a kind of preferred orientation called fiber texture in metal wires. Such textures have been extensively studied by means of X-ray diffraction, chiefly by techniques in which the diffracted X-rays are recorded photographically. This paper describes some results obtained with a new method, involving the use of a diffractometer. X-RAY METHOD Since the pole figure of a material having a fiber texture is symmetrical about the fiber axis, there is no need to present the entire pole figure. Instead, texture data can be summarized by means of a curve showing the variation of pole density along any meridian of the pole figure, if the north-south axis of the latter is made parallel to the fiber axis. The position of a pole on the meridian is specified by the angle 9 between the pole and the fiber axis (wire axis). The X-ray method1 used here to measure pole density as a function of 9 actually consists of two methods, referred to as A and B. In method a, X-rays are reflected from the wire surface. Pole densities can be measured by this method from O = 90 deg down to a limiting value which is dependent on the Bragg angle 8 and is typically of the order of 30 to 40 deg. Method B involves diffraction from the wire cross section and covers a range of 0 values from 0 up to an angle sufficient to overlap the measurements made by method A. By a combination of the two methods, a complete pole-density curve can be obtained. However, method A alone, which requires no specimen preparation other than etching, can often reveal enough of the pole-density curve to provide complete information about texture components. Both methods require that the measured diffracted intensities be corrected for changes in absorption and diffracting volume with changes in 9. A11 intensities I reported in this paper are corrected diffracted intensities; they are propor-

Jan 1, 1960

By Robert F. Mehi

The mechanical behavior of metals and alloys is presumably conditioned by two factors; namely, the crystallinc symmetry and the interatomic forces. Considerable attention has been given to the first of these factors through the recent advances in X-ray technique. It is the purpose of the present paper to call attention to the importance of the second of these factors, to point out promising methods of investigation, and to present some pertinent data. Plastic deformation takes place by slip along atomic planes.' This slip may be inhibited in a number of ways: by the interatomic forces of, cohesion which bind the atoms rigidly in a lattice structure, which in pure metals is usually of high symmetry; by latticc distortion caused by solid solution formation or by mechanical strain; by the intercrystalline boundaries whcrc slip is restrained, probably by the non-registration of the atom planes in adjacent crystal1ites;2 and by the presence of small hard particles which serve to "key" the slip along the atom planes.5 In pure metals, and perhaps also in solid solutions, the atom planes of easiest slip are those exhibhing the greatest density of atomic population and the greatest interplanar distance4 and apparently can now be pre-dict,ed from the analysis of the lattices. Concerning the interatomic forccs, which resist this slip by holding the atoms firmly together, little is known. Most textbooks on physical metallurgy, following the work of Bot-tone,5 correlate the hardness of the pure metals with the atomic volume,

By N. Schapiro, R. J. Gray, G. D. Coe

A petrographic and chemical investigation was conducted to determine the occurrence and distribution of the organic and inorganic forms of sulfur in various size and specific gravity fractions of a high volatile, A-rank, Pittsburgh seam coal. The investigation was conducted to aid in the resolution of the problem of how metallurgical coke of lower sulfur content can be produced from high sulfur coals. The Pittsburgh raw coal contains about 2.4% S in two dominant forms: pyritic and organic. Pyritic sulfur constitutes about 57% of the total sulfur in the raw coal and occurs in macroscopic and microscopic-size particles. A plant cleaning process mechanically separates between 50 and 60% of the pyritic sulfur, mainly the macroscopic particles. The organic sulfur constitutes 41% of the total sulfur in the raw coal and 55% of the sulfur in the washed coal. Thus, organic sulfur is not reduced by physical methods of separation. Organic sulfur occurs in all the coal entities, but in general, increases as the exinoid content of the coal increases. In this study, it was found that carbonizing certain selected low gravity coal fractions containing an average of 0.45% pyritic sulfur and 1.01% organic sulfur produced cokes containing an average of 0.22% pyritic sulfur and 0.91% organic sulfur. However, the organic sulfur in the coke is probably derived in part from the heating of pyrite in the presence of carbon. Thus, the total sulfur in the coal carbonized is the most important factor affecting the sulfur content of the coke produced. Concentration of microscopic pyritic and organic sulfur in the middling-type coal indicates the necessity for rejecting as much of this material as is economically feasible. Most of the sulfur introduced into the blast furnace originates from the coke. Although the sulfur content of the hot metal can be controlled by the addition of flux, the flux used restricts the productivity of the furnace by displacing ore and requires first to be smelted; therefore, low sulfur coke is highly desirable. Since the sulfur content of coke is dependent upon the sulfur content of the coals from which the coke is produced, low sulfur coals are required to produce low sulfur coke. In the western Pennsylvania area, large quantities of good coking coal are available from the Pittsburgh seam, but this coal unfortunately contains relatively large quantities of sulfur. To provide information that might be useful in reducing the sulfur content of this coal in the cleaning process, an investigation was conducted to determine the physical and chemical forms in which this sulfur occurs and with what petrographic components it might be associated. The Pittsburgh seam coal, like most other coals, contains two dominant forms of sulfur: one occurs as the minerals pyrite and/or marcasite and is referred to as pyritic sulfur; the other is combined with the coal substance and is called organic sulfur. Pyritic sulfur is amenable to physical methods of separation, whereas organic sulfur is not. Pyritic sulfur particles must be freed from the surrounding coal if they are to be removed in the washing process. Generally, this requires crushing; the required degree of crushing being a function of the size and distribution of the pyrite. The present investigation was conducted to 1) determine the size, distribution and association of sulfur-bearing minerals in the coal and 2) to determine whether the organic sulfur has a preferential association with specific coal entities. If a preferential association exists, this knowledge may be useful in devising a method for organic sulfur reduction. In addition, a study was made to determine the extent to which pyritic and organic forms of sulfur in the coal contribute to the sulfur in the coke produced from this coal. A representative 3%-ton sample of raw coal was crushed to —3 in. and screened into square-mesh sizes: 3 to 1 in., 1 to % in., % to % in., % in. to 10 mesh, 10 to 35 mesh, and 35 to 200 mesh. Separate samples of the -200-mesh fraction and the all-size composite were also collected. Each size fraction (except the -200 mesh) was fractionated on heavy liquids of the following specific gravities: 1.280, 1.300, 1.325, 1.350, 1.375, 1.400, 1.425, 1.450,

Jan 1, 1963

By M. C. Dow

INTRODUCTION BELT conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stonecrushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. GENERAL RELIABILITY It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 1/2 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. LOADING THE BELT It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined conveyor to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1947

By Kenneth K. Humphreys, Joseph W. Leonard, Robert L. Llewellyn, William F. Lawrence

INTRODUCTION Cleaning fine coal sizes utilizing air currents in machines as the primary separating medium is called dry concentration or pneumatic cleaning. In 1947 approximately 18 million tons (16.38 million mt) of bituminous coal were cleaned by air machines; in 1965, 25.4 million tons (23.1 14 million mt); but in 1975, only 7 million tons (6.37 million mt). Table 11-1 shows the tonnages cleaned of bituminous coal and lignite in the United States by various types of equipment from 1938-1963. Table 11-2 shows only tonnages cleaned by pneumatic methods from 1964-1975. The decrease in tonnage to approximately 7 million tons (6.3 million mt) is due to a higher moisture content in the mined coal and the greater difficulty in cleaning the coal by air. There also was a definite trend to load raw coal at the mines, especially the slack which is the most expensive to clean due to the dewatering and drying requirements. While there have not been any applications of pneumatic cleaning in the anthracite field, its use has not been fully explored. The same is true for lignite and subbituminous coals.

Jan 1, 1979

By C. A. Heiland

The following summary is written for the benefit of the practical operator in the nonmetallic field who wishes to know what geophysics has done and may be expected to do in his line of work. His problem is quite different from that of the geophysicist who has operated with various or all methods and has followed the literature, and who is assumed to be familiar with the geologic possibilities and limitations of each method. This article is not written for the latter, although he may be interested in the four or five hitherto unpublished surveys described. To the operator, on the other hand, geophysics is only secondary. His problem is to determine which geophysical method is best suited to his special needs. If he wanted to know, however, which method could be used to locate a certain material of given physical properties, building stone, for instance, he would have to wade through a tremendous amount of geophysical literature, bibliographies and articles, before he could find what he wanted. Therefore, the purpose of this summary is to present the geological problems first and then to discuss the comparative merits of the geophysical methods that can be, or have been, applied. Choice of Geophysical Methods in Oil, Civil and Mining Engineering In the first two of these fields, the geological problems are not nearly so complex as in the metal and nonmetallic mining fields. The selection of the correct geophysical method in these fields is not nearly so difficult for the operator. For oil prospecting, his problems have been discussed exhaustively by E. DeGolyer.(1) † In civil engineering (foundation and ground-water work), the usefulness of electrical methods has been so well established that there is hardly any choice of other methods at present. The situation may be changed in the future with the perfection of the seismic reflection method for shallow depths. In the mining field the operator and often the geophysicist himself finds difficulty in determining which method is best suited for a given

Jan 1, 1934

By G. L. Oldright, T. B. Brighton, C. M. Dice

The base bullion from the lead blast furnace contains varying amounts of the impurities left in the smelter feed by the concentrator, regardless of the method of smelter operation. These impurities may be held in part in mechanical suspension rather than being present as true alloys. However, usually there is little free space in the crucible in which to separate these drosses before the bullion is taken from the lead well. When such a dross is melted in a laboratory crucible and allowed to cool, the products obtained are lead bullion, speiss, and matte in well separated layers. Typical analyses of layers are: Analyses. Per Cent Element Bullion Speiss Matte Pb.............................................. 92.0 41.2 38.3 Cu.............................................. 2.4 36.3 40.6 As............................................... 4.0 16.5 4.3 Sb............................................... 0.7 0.2 0.4 S................................................ 0.6 1.9 13.1 Fe............................................... 0.0 0.0 0.0 Totals......................................... 99.7 96.1 96.7 The absence of iron in these products drossed from the blast-furnace bullion proves that the impurities for the greater part are not simply finely divided blast-furnace speiss or matte that has been dissolved or dispersed in the lead, but are held in solution by the liquid metal and rise to its surface as infusible compounds when the temperature of the bath is lowered. In general, the drosses made locally are metal sulphides and arsenides and not oxidized compounds. The large content of metallic lead also does not seem to be retained because of oxidized compounds

Jan 1, 1937

By H. S. Drinker

THE first discovery of zinc 011 the property now worked by this company was made by the celebrated mineralogist, Prof. William Theodore Rapper, in 1845. Different claimants kept the property in continual litigation till 1861, when everything was satisfactorily settled by the purchase of the land by the company, who have worked it ever since. The mines are situated in a valley, four miles south of Bethlehem, Pa., in Lehigh County. The valley is from two to three miles broad, and is bounded 011 the north and south by syenitic hills. Syenite underlies the valley, and upon this is deposited the Potsdam sandstone, then a layer of slate, and, finally, a dolomitic limestone, belonging to the Chazy or Black River formation, in which the zinc deposits are inclosed. The rocks occur in folds, and have evidently been subjected to tremendous pressure from below, the zinc deposit being found in an anticlinal axis, in nearly vertical veins. I t is supposed that the zinc was originally disseminated through the

By M. J. Blackburn

The ordering reaction and its effect on dislocation awangements in alloys based on Mg3Cd has been studied by transmission electron microscopy. Ordering occurs by the growth of ordered domains until they impinge, thus producing an antiphase domain boundary (APB) network. In the disordered alloy, slip is confined to the basal plane while in the ordered condition slip occurs on the basal, prism, and pyramidal planes. Superdislocations have been identuied on these planes and their origin and expected spacings are discussed and compared with the observations. The APBs between the dislocation pairs have been resolved and have proved useful in the identification of superdislocations. Observed slip structures are related to the changes in mechanical properties produced by ordering. At high temperatures magnesium and cadmium form a continuous series of disordered hexagonal solid solutions. At lower temperatures three ordering reactions occur; two based on the compositions Mg3Cd and MgCd3 are transformations to DO19-type superlattices while alloys based on the composition MgCd transform to a B19 lattice. The ordering process in alloys near the composition Mg3Cd has been studied by several workers'-4 and it has been shown to be a first-order type transformation. The variation of mechanical properties with the degree of order and temperature have been reported in some detail by Stoloff and Davies.5 It was shown that the disordered alloy was stronger and less ductile than the ordered alloy, the differences being attributed to changes in the number of active slip planes and to the presence of short-range order in the disordered alloy. In this investigation the ordering reaction has been qualitatively followed by transmission electron microscopy. The effect of this ordering transformation on the dislocation arrangements in deformed specimens has been studied in some detail. EXPERIMENTAL Alloys were melted in a stainless-steel crucible under a flux and chill cast; both melting and casting were performed in an argon atmosphere. The ingots were hot-rolled and tensile specimens cut from the resultant strips. Some large-grained specimens were grown by the strain-anneal method. Heat treatment was carried out in inert atmosphere furnaces and in oil baths at the lower temperatures. Thin foils for transmission electron microscopy were produced by electropolishing in a cooled solution (temp = -40°C) containing 50 cu cm of nitric acid and 180 cu cm of methanol at a potential of 10 v. The ordering reaction was followed by transmission electron microscopy, X-ray, and electrical resistivity measurements but this paper will be concerned chiefly with the electron-microscopy results. Much of the work described in this paper was performed on an alloy containing 26.10 at. pct Cd although two of the micrographs are taken from work on a 25.55 at. pct Cd alloy. RESULTS i) The Quenched Solid Solution. Specimens which were quenched from above the critical temperature showed diffuse superlattice reflections. sark-field analysis on these reflections failed to reveal the presence of ordered domains and thus the superlattice reflections were assumed to arise from regions of short-range order. Quenching from temperatures of 400" to 450°C results in the formation of dislocation loops and helical dislocations. Such defects have been observed and analyzed in detail in several hexagonal metals6-' and as the crystallography and interactions of such loops appear similar in this alloy they will not be reported in detail. Fig. 1 shows a high density of loops

Jan 1, 1968

By William E. Ford, Edward Salisbury Dana

This section includes one distinct group, the Stibnite Group, to which orpiment is related; the other species included stand alone. Pyr., etc. - In the closed tube melts and gives a dark red liquid when hot and a red- dish yellow solid when cold; in the open tube (if heated ver slow? ) sulphurous fumes, and a white crystalline sublimate of arsenic trioxide. B.B. on ciarcoaTburm with a blue Hame, emitting arsenical and sulphurous odors. Soluble in caustic alkalies. Artif. - Realgar is frequently noted as a sublimation product from furnaces roasting ores of arsenic. Crystals are produced when arsenic sulphide is heated in a sealed tube with a solution of sodium bicarbonate. Obs. - Realgar occurs usually in veins associated with silver and lead ores. It has been found in volcanic regions as a sublimation~duct. It has also been noted as a deposit from hot spring waters. It is often rtasociate wlth orplment. It occurs at Felsi5bBnya, Kapnik and NagyAg, Hungary; Allchar, Macedonia. Binnental, Switzerland, in dolomite. In the United States, at Mercur, Utah; in the Norris Geyser Basin, Yellowstone Park, as a deposition from the hot waters. Found at the Monte Cristo millin district, Snohomish Co., Washington: the namerealga7 is from the Arabic, Rahj af gh&r,powder of the mine. Use. - Was used in fireworks to give a brilliant white light when mixed with saltpeter and ignited. The artificial material is now used for this purpose.

Jan 1, 1922