Search Documents

By J. B. Conway

RECENT studies of first-stage creep data have led to a special least-squares procedure for use in calculating the Andrade creep-equation constants. This procedure is easy to apply, uses only experimental data, and yields results which do not vary with the individual making the analysis. Taking logarithms of the Andrade equation I = lo(1 +ßl1/3)ekt leads to In l = In lo + In(1 + ßl1/3) + kt A residual can then be defined as the difference between the logarithm of an experimental length value and the logarithm of a calculated length value. Following the usual least-squares approach differentiation with respect to 10 and k of the expression for the sum of the squares of the residuals leads to two equations which cannot be solved directly for the three constants involved. However, values of ß can be assumed and corresponding values of lo and k can then be calculated. Then the sum of the squares of the residuals can be calculated. For a certain value of ß this sum will exhibit a minimum value to identify the least-squares values for ß, lo, and k. An illustration of the application of the above least-squares approach is obtained by employing the creep data for lead originally presented by Andrade' in the development of the one-third creep law. A plot of the sum of the squares of the residuals as a function of ß is shown in Fig. 1 along with the corresponding lo and k values. The minimum is seen to occur at ß = 0.0143 from which lo = 39.149 and k = 7.27 x 10-5. Based on these results the Andrade equation for these lead data is 1 = 39.149(1 + 0.0143 t1/3)e7.27 x 10-5t compared to the equation I = 39.13(1 + 0.01457/l/3)e6.95 X 10-5t developed by Andrade (calculation procedure not given but was probably a graphical solution). Calculating length values using the above equations and comparing with the experimental length values, residuals corresponding to the difference between experimental and calculated length values can be obtained. The sum of the squares of the residuals can then be calculated. For the case of the least-squares approach a value for this sum was found to be 2.37 x 10-3 compared to a value of 3.47 x 10" for the equation originally proposed by Andrade. In other words, while the constants proposed by Andrade provide an excellent fit for the lead data, a still better representation is afforded by applying the least-squares approach discussed above. A similar result was obtained for the lead data at 162oc.l The least-squares approach led to 1 = 9.866(1 + 0.0497 t1/3)el.011 x 10-2t compared to the equation I = 9.94(1 + 0.0433 l1/3)e1.06 X 10-2t given by Andrade. In this case, too, the sum of the squares of the residuals is slightly smaller for the equation based on the least-squares approach. It should be pointed out that a double trial and er-

Jan 1, 1965

By H. I-Lieh Huang, O. D. Sherby, J. E. Dorn

RECENT investigations1-4 have suggested that the total plastic strain, C, for high temperature creep under a given stress can be correlated by means of a temperature-compensated time, te- where t is the duration of test, e is the base of natural logarithms, aH is the activation energy for creep, R is the gas constant, and T is the absolute temperature. A typical set of data on which this deduction was based is given in Fig. la. Inasmuch as the e-in t curves for the various temperatures are identical except for their displacement along the In t axis where f and are appropriate functions. If the increase in creep rate with an increase in temperature is exclusively ascribable to a single process involv- ing thermal activation, (T) should equal RT and therefore it = constant [2] where ?= te Assuming the validity of this relationship, ? = ?2 at the same strain, or where the subscripts refer to two alternate test conditions.

Jan 1, 1957

By Franz Posepny

CONTENTS. Introduction. Part I. General Facts And Theories. [ ]

Jan 1, 1902

By C. A. Stetefeldt

Jan 1, 1895

By L. G. Austin

If S (x) is the specific rate of breakage of size x and B (x, y) (see Table 1 for Nomenclature) is the cumulative breakage distribution function, the Herbst Fuerstenau2 assumption is that Inserting this assumption into first-order grinding equations it has been shown" that there are then simple analytical solutions to the grinding equations, as shown in Table 2. In this context "plug flow" is defined as all material passing through the mill in the same length of time, the residence time t. The term "n fully-mixed" means that the mill has a residence time distribution" which can be treated as if the mill were n equal fully mixed sections in series. In addition it has been shown that the assumption of Eq. 1 also leads to simple analytical solutions for closed-circuit, steady-state grinding with an ideal classifier at the mill exit returning oversize to the mill feed. The solutions are also given in Table 2, with µ as the ideal classifier cut size, C the circulation ratio, and Q (x) the size distribution of the circuit product. The specific surface area of these size distributions is where the density-shape factor k. is assumed to be constant with size. In practice, most methods of size analysis or area [ ] measurement have a finite lower limit, so that the integration is really performed from xm, to xm, For a realistic degree of grinding the value of So is dominated by the fine sizes because of the 1/x factor. Consider batch grinding of a feed of size y to y + dy. The batch grinding solution given in Table 2 is then [ ] The fresh surface area produced is the area of the fines plus the area of the original material remaining minus the area of the original material, [ ] Little error is introduced by neglecting the last term on the right-hand side since at t = 0 it is zero, and when t is significant the first term dominates because of the fine sizes produced. In addition, the form of P (x, t) for [ ] realistic values of S (x) 2t ax° is such that the major fraction of fresh surface produced is contained within the bottom 10% of weight of broken material, that is, for sizes for which P(x, t) < 0.1 (providing y is not near x.,). Thus for surface area purposes Eq. 3 can be approximated by [ ] becomes providing again that the feed sizes are coarse relative to xmi. Then the fresh area production is and W is the mass in the mill. The rate of surface production is WK, and the specific surface is Kt. From Table 2, the specific energy is mt/W so surface production per unit energy is [ ] Surface produced per unit energy input = KW/m (8) where m is the energy input of the mill. Clearly, identical reasoning applies to open-cycle, plug-flow grinding, with t replacing t, and Eq. 8 is obtained again. Considering open-cycle, fully mixed grinding, similar reasoning gives P(x) - t S(x) for surface area purposes, and

Jan 1, 1974

By L. C. Uren

Some of US have been impressed with the need for a better understanding of the future place of the engineer in the petroleum industry. In academic work we are continually asked to advise students as to the opportunities in different directions, to guide them in their selection of professions, and it would be extremely helpful to those in academic lines of work to have the opinion of engineers from the industry relative to the need for petroleum engineers. IS the industry going to require a continually growing number of engineers in the future years, or have we perhaps reached equilibrium in that regard ? In anticipation of this meeting, I undertook to canvass opinion among a number of engineers of my acquaintance and I have been rather astonished to learn that the expenditure on engineering salaries in the producing branch of the oil industry is extremely low. I have figures from eight or 10 of the larger oil companies and it seems to be a fair statement on the basis of these figures to say that the average American oil company is devoting less than 2 per cent. of its gross expenditures in oil production to the payment of engineering salaries. A few examples will be of interest. I shall not mention names of individual companies, but one large Mid-Continent company is spending slightly less than 1 per cent. of its gross expenditure—that is, less than 1 per cent. of the total expenditure in the producing department—on engineering salaries and about as much on engineering research, which might properly be regarded as a phase of its engineering work. Another Mid-Continent company is spending about 11/4 per cent. on engineering salaries. A large California company is spending about l1/2 per cent. The largest figure that has come to my attention is that of an important Rocky Mountain and Mid-Continent company that is spending a little more than 6 per cent., but that is apparently an extreme case. The petroleum producing industry is a highly technical business in these days. It is spending in excess of $500,000,000 annually in new

Jan 1, 1929

By AIME AIME

THE Board of Trustees, made up of three from each of the four societies, conducts the business com- mitted to United Engineering Society by its Founder Societies under its Charter, the Founder&apos;s Agreement and the Library Agreement. A draft of a budget of revenue and expenditures for the ensuing calendar year is presented each September to the secretaries of the Founder Societies for the information and comment of their governing bodies. After revision, the budget is adopted, by the incoming Board of Trustees at its meeting in January.

Jan 1, 1929

Following is the personnel of the various society and national committees on which the A I M E is officially represented United Engineering Society Officers of the Board, 1921 JOHN VIPOND DAVIES, President CALVERT TOWNLEY, 1st Vice-president ALFRED D FLINN, Secretary WILLIAM L SAUNDERS, 2d Vice-president JOSEPH STRUTHERS, Treasurer Finance Committee House Committee CALVERT TOWNLEY, Chairman ALFRED D FLINN, Chairman GEORGE H PEGRAM . H S CROCKER WILLIAM L SAUNDERS BRADLEY STOUGHTON GEORGE M BASFORD CALVIN W RICE F L HUTCHINSON

Jan 1, 1923

By K. R. Price, M. Gauna

A high seam geologic condition exists at Jim Walter Resources No. 4 mine that requires immediate rib support after a continuous miner cuts a place. High seam mining heights are typically 2.4 to 2.6 m (8 to 9 ft) and a thick rock layer is present in the upper portion of the coal rib side. The 610-m (2000 ft) mining depth at No. 4 mine induces horizontal rib line movement after excavating an entry. Horizontal rib movement greater than 305 mm (12 in.) have been noted. When lateral movement occurs in the high seam areas, the thick rock layer, and the coal above the rock layer, become fractured and tend to roll into the entry. If not adequately supported, large rib rolls develop in the place being bolted as well as in previously mined areas that endanger men and equipment. To control this, rib support must be installed in the roof bolting operation as the bolting crew works toward the face. A rib control system has been developed for this high seam mining condition using a mechanical anchor bolt placed at an angle in the rib and installed with a modified Fletcher DDM-15 bolting machine. More than 120 km (75 miles) of entry have been supported with angle rib bolts. These angle bolts constitute 43% to 60% of the total roof and rib bolt footage in the high seam portions of No. 4 mine. The angle rib bolting system has proven safer, more effective, and more efficient than the earlier support method using bolts installed horizontally into the rib. No rib roll accidents have occurred since the angle drill bolting machines were placed in service in 1981. By securing the broken rib material with an angle bolt anchored above the coal pillar, a more effective means of rib control is achieved. Angle rib bolting does not interfere with continuous miner productivity. In addition, bolting crews are now reduced from three to two people. Total drilling supply costs are about 60% the previous cost, when compared to the previous support method using horizontal rib bolts:

Jan 1, 1985

By Richard Hamburger

Calculating machines permit the use of the more rapid cotangent and semigraphic solutions of plane triangulation. The results of these methods are as accurate as those of other methods. Simple adjustment of the net, and ease of calculation encourage more complete field work. Errors in field work or in computation are easily localized.

Jan 1, 1950

By Theodore Swann

DURING recent years, there has been a material increase in the use of ferrophosphorus in the steel industry. It has been observed, when rolling sheets, that those made of Southern iron did not have to be rolled at as high a temperature as the others and, consequently, did not stick together. The reason was found to be the phosphorus content of Southern iron. It was therefore thought that an addition of phosphorus to sheet steel of other than Southern origin would give the same result as the use of Southern iron. At first, this addition was made by intro¬ducing phosphate rock in the blast furnace and reducing it together with the iron ore; but, because of the necessity for only small quantities of this grade of iron, the process was not satisfactory. The manufacture of ferrophosphorus was then introduced, so that additions might be made to the open-hearth furnace or ladle. Ferrophosphorus was first manufactured in the blast furnace. This method, however, can only economically produce a grade of product up to about 20 per cent. To produce a higher grade, it would be necessary to charge a larger proportion of phosphate-bearing material; and as the rate of absorption by the iron is low, there would be an increased loss of phosphorus oxides. This feature makes the production of a higher grade ferrophosphorus in the blast furnace uneconomical. The use of high-grade ferrophosphorus in the steel requires a smaller addition and involves, besides the economies in handling, an additional economy in transportation. The alloy with a higher percentage than 20 per cent. can be made only in the electric furnace. In the ordinary operation of the electric furnace in the production of ferrophosphorus, an alloy may be produced containing 26 per cent. phosphorus; this is the limit, for it does not seem possible to produce a higher phosphorus alloy even if large excesses of phosphatic materials are used. The reasons for the difficulty in raising this percentage of phosphorus are not known. The compounds Fe3P, containing 15.6 per cent., and Fe2P, containing 21.7 per cent. phosphorus, have been studied and it appears as if the alloy produced, containing percentages of

Jan 10, 1924

THE Executive Board of The American Engineering Council met in Pittsburgh, May 26 and 27. Its actions on the licensing of engineers and on the Employment Bureau are printed at length elsewhere in this issue. The board announced plans purposing the solution of the national problems of water power and forestry, upon which "the industrial development of the nation and the standard of living of future generations largely depends. The whole Federal water-power situation is in so critical a condition that immediate constructive action by the Government to conserve the public interests, involving vast consequences of economic and Federal policy, is necessary. After a long discussion during which the water-power problem as it affects Government reorganization was reviewed and Henry Ford&apos;s Muscle Shoal&apos;s plan was discussed, the board decided to lay the entire question before President Harding. A national movement to conserve the nation&apos;s forests, in which engineers, the U. S. Forestry Service, the forestry services of the states, universities and technical schools, and other groups such as the farmers, the railroads, and lumbermen, shall pool their efforts, was set in motion by the engineers. The work will be in charge of a Reforestation Committee of the Council, headed by Charles H. MacDowell of Chicago. Mov-ing picture interests will be asked to aid. The board pledged its support to President Harding in his plan for Government reorganization. In adopting the report of its Committee on Public Affairs, headed by J. Parke Channing of New York, the Executive Board of the council determined, in the event of the failure of the President&apos;s efforts to bring about greater economy and ffieciency in national affairs by regrouping of Federal functions, to press independ-ently a nation-wide movement for the establishment of a Department of Public Works. Progress in a national survey of the two-shift day in American industries was reported by the Council&apos;s Committee on Work Periods in Continuous Industries. This survey, called the most extensive of its kind ever made, has been in progress for more than a year; and purposes an exposition of industrial conditions which shall form a basis for establishing the relative merits of three shifts of eight hours each and two shifts of twelve hours each.

Jan 7, 1922

The Secretary : The work of Mr. A. E. Outerbridge, Jr., of Philadelphia, first made known in his paper on " The Mobility of Molecules of Cast-Iron," read at the Pittsburgh Meeting of the Institute, in February, 1896, has been reviewed by the Committee on Science and the Arts of the Franklin Institute, whose report, dated May 5, 1897, is accompanied with a table of tests made by the Committee, and amply confirming the statements of Mr. Outerbridge. Concerning the originality and novelty of his investigation, the Committee says: " The fact that a certain molecular change takes place in cast-iron in the course of time has been known and recognized by many persons for a long time, and that this change tends to relieve the internal strains and render the casting tougher has often been noticed and acted on, although in a very crude way; but, so far as the sub-committee has been able to learn, Mr. Outerbridge has been the first to make a careful study of this, and to note that the change may be hastened by impact, and the whole effect produced in a short time, and also to make a scientific study of the phenomenon. We believe great credit is due him for the initial observation and the careful work dependent thereon. The results were first given to the public in a paper read before the American Institute of Mining Engineers, on February 20, 1896. This aroused a wide-spread interest and discussion among users of cast-iron, and so far as the sub-committee has been able to determine, it has not been shown that anyone, either in this country or abroad, has antedated Mr. Outerbridge in his work in this line. The Franklin Institute therefore recommends the award to him of the John Scott Legacy Premium and Medal." This report has not been published, hut I have had the opportunity to read it in manuscript. The table of testa accompanying it comprises 91 tests of " rumbled" and an equal number of " not rumbled" companion-bars of cast-iron, 26 by 2 by

Jan 1, 1898

Lieut. Maxwell E. Erdory, now with the Army of Occupation in France, writes as follows: "The 602d Engrs., many of whose officers are members of the Institute, started its active service in France at Avocourt, where we built a road across `No Man&apos;s Land.&apos; This road from Avocourt to Montfaucon started us on a career of road building which lasted from Sept. 26 to Nov. 9. The engineer in war has no working hours. Our first job meant 50 hr. continuous work, a layoff of 4 hr. and 18 hr. more. That was our initiation in this war game. "Back in the States we practised building trenches, dugouts, and underground shelters of all sorts. In France we were unfortunate enough to come upon the scene when the so-called open warfare started. That made all the above unnecessary. Roads was the cry and our job was to see that all the artillery got their roads and got over them. "I might mention here that the roads of France, which were in excellent condition except for numerous shell holes, w re one of the leading factors in the rapid termination of the war. "We built a narrow-gage railroad from Romagne to Landre St. George which cost us a few men. At Stenay we did our first bridge building. We built nine bridges across the Meuse, capable of carrying tanks, in 18 hr. The next day the American army crossed these bridges on their way to Virton, Belgium, and the Rhine. " Our course from Virton, Belgium, took us through Longwy, Musson, and Athus, in which towns I inspected the steel plants. In Musson as well as Longwy the Germans had destroyed most of the blast furnaces. This destruction began in August, 1917. In Athus the furnaces were in good condition, the Germans having removed all motors land electrical apparatus, rendering the plant inoperative. I have taken several photos of interest of these plants. "It is but fitting that I say that the engineer in this war has contributed much toward its success but the "Doughboy" is its hero and we engineers one and all say "All hail the Doughboy."

Jan 2, 1919

By J. F Haseman, J. E. Davenport

In the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1,2 results in inadequate beneficiation. Investigation of Flotation Methods Flotation has been used in &apos;Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate. 3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P2O5 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P2O5, 20; SiO2, 40; CaO, 29; Fe2O3, 2; Al2O3, 3; F, 2.3. The particle-

Jan 1, 1948

By J. F. Haseman, J. E. Davenport

In the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1,2 results in inadequate beneficiation. Investigation of Flotation Methods Flotation has been used in &apos;Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate. 3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P2O5 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P2O5, 20; SiO2, 40; CaO, 29; Fe2O3, 2; Al2O3, 3; F, 2.3. The particle-

Jan 1, 1948

By J. F. Haseman, J. E. Davenport

IN the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1-2 results in inadequate beneficiation. INVESTIGATION OF FLOTATION METHODS Flotation has been used in Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate.3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over-all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P205 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P205, 20; Si02, 40; CaO, 29; Fe203, 2; A1203, 3; F, 2.3. The particle-

Jan 1, 1947

By H. 0. HOFMAN AND W. MOSTOWITSCH

I. INTRODUCTION. THE mineral gypsum, CaSO, + 2 H2O, has been used for many years as a sulphurizing and basic flux in several smelting¬operations. Thus, in smelting oxide nickel-ore in the blast furnace, it is commonly added to the charge to furnish the sulphur necessary for collecting the metal in a matte, and a base for slagging the siliceous gangue. In the concentration of lead-copper matte in the reverberatory furnace it has been used for years at Freiberg, Saxony1 for a similar purpose, and for producing at the same time a copper-matte with less than 0.15 per cent. Fe. The latest use gypsum has been put to is in the blast-roasting process of Carmichael-Bradford.2 The term "blast-roasting," given by A. S. Dwight3 to the Dwight-Lloyd method of roasting and agglomerating ,I is a happy generic term which covers the ground better than the " lime-roasting" of Ingalls&apos; or the " pot-roasting " of Austin,6 in that it leaves the operation independent of the character of the flux and the form of apparatus, and retains the characteristic feature of this class of processes-namely, that of using forced draft. In the Carmichael-Bradford process the dehydrated material, mixed with galena-concentrate, acts as a diluent and a flux. The process differs in this from the Huntington-Heberlein7 and the Savelsberg8 processes, in both of which limestone is used.

Jan 1, 1909

By A. B. Parsons

Not so many years ago the interest of the average mining engineer in money matters-aside from his pay check or his consulting fees-was confined to the per-ton cost of mining and beneficiating ore and to the amount of capital that would be required to erect the plant necessary to carry out such operations on a prescribed scale. The so-called "business men" assumed that questions of marketing the products, of profits, and of dividends were in their exclusive sphere-matters too intricate or, perhaps, too practical for the mere engineer! In the case of a new enterprise, the promoter shouldered the entire responsibility for raising the necessary funds, and incidentally he got the lion&apos;s share of profits. In fact, he frequently profited handsomely even though the mine earned little or nothing. Occasionally the engineer turned promoter or entrepreneur--conspicuous examples are Herbert Hoover, D. C. Jackling, William Braden and F. W. Bradley- but by and large he remained in a sphere of his own. To what extent this condition of affairs has changed is difficult to say. It might be argued that it were better that it be not changed; and yet I cannot help feeling that in mine promotion lies a distinct opportunity for the

Jan 1, 1932

By C. A. Stetefeldt

FoR the convenience of those who do not care to enter into the details of this long essay, I begin with a summary of the most important results it presents. The extraction of silver by the lixiviation-process from ores which have been subjected to a chloridizing-roasting, is based upon the fact that silver chloride is easily soluble in solutions of sodium or calcium hyposulphite, and that silver is precipitated from such solutions by an alkaline sulphide, with regeneration of the hyposulphite salts. In case the ore contains lead a large portion of the latter is and dissolved, lead sulphate being soluble in hyposulphite solutions. If, at the same time, copper is present, the sulphides precipitated from the solution, contain silver, copper, and lead, a combination of metals not desirable for subsequent treatment. Mr. E. H. Russell, of Park City, Utah, is the inventor and the patentee in the United States and several foreign countries of a new lixiviation-process, based upon the chemical facts discussed in this paper. Mr. Russell has discovered that lead can be completely separated from a sodium hyposulphite solution, as lead carbonate, by sodium carbonate or purified soda-ash, without precipitating any copper or silver. After decanting the solution from the lead carbonate, silver and copper are obtained from it in the usual way. This method of separating lead prohibits the use of calcium poly-sulphide as a precipitant for the sulphides, because any calcium entering the regenerated lixiviationsolution would also be precipitated as a carbonate with the lead by soda-ash. Hence, a sodium sulphide must be employed. A full investigation has demonstrated that this is by no means detrimental. Sodium sulphide and hyposulphite are more advantageously used in the lixiviation-process than the corresponding calcium-salts. Another defect in the lixiviation-process consisted in the necessity of a very perfect chlorination of the silver in the ore, because silver in

Jan 1, 1885