Search Documents

By Danilo Gonçalves de Oliveira, Rogério Martins Pereira

Chatter is a widely studied vibration phenomenon that affects most cold mills around the world and its impact on these lines are tremendous: from productivity and quality losses to mechanical equipment damage. The investigation of its origins and how to minimize the occurrences and their impact on the equipment require special instrumentation and algorithms in order to have a detection of the vibrations as soon as they start. This paper presents three methods of identification of chatter on a Tandem Cold Mill and the actions to leave the vibration frequency range before its amplitude achieve catastrophic values.

Oct 1, 2019

By Lidong Teng

ArcSaveTM is a new generation of electromagnetic stirrer (EMS) from ABB for electric arc furnace (EAF) operation. Its goal is to improve the safety, increase the productivity and reduce costs. Electromagnetic stirring in the melt bath during arc furnace operation will affect the scrap smelting, bath temperature distribution, refining reactions, and also the tapping practice. This paper has summarized the investigation results obtained from the first ArcSaveTM system installed in a 90 ton EBT arc furnace in USA. The hot test results show that ArcSaveTM has enhanced the heat and mass transfer in the arc furnace process. This results in a faster scrap melting rate, lower slag superheat during arcing, more homogenous melt bath, higher decarburization rate and higher EBT free opening frequency. ArcSaveTM has also reduced the tapping temperature and tapping oxygen in the steel. This brings a higher scrap yield and saves ferroalloy consumption in the downstream ladle furnace operation. The lower energy consumption, short tap-to-tap time, and consistent furnace operation bring increased productivity and safety.

Aug 16, 2017

By Mohammad Masoumi

In the present study, API 5L X70 pipeline steel samples were deformed by hot-rolling cooled in air or quenched in water and subsequently tempered at different temperatures. X-ray diffraction (XRD) and electron backscatter diffraction (EBSD) technique were used to analyze the texture evolution from the initiate state to rolling and tempering state at mid-thickness and near surface plane of all samples. The results showed that the mid-thickness region is richer in {100}//ND oriented grains known as more susceptible to crack formation and growth through. Hot deformed specimen showed dynamic recrystallization grains while quench tempered sample at 700°C evidenced recovery and grain growth.

Aug 16, 2017

By "Andreas Steinwandter

The demand for increasing energy efficiency and CO2 reduction is one of the global megatrends of our time. Although the steel industry suffers from a volatile economic environment, the steel plants are interested to find opportunities for sustainable cost reduction and put efforts into healthy solutions for the environmental. Integrated steel plants are trying to cut electrical power and energy costs as these are among the biggest cost factors that can be influenced and taking all the advantages they can. For the integrated iron and steel making route the interaction of waste energy utilization along with process energy demand, natural and metallurgical gases, steam and heating systems as well as power generation has to be considered. Potential energy sources, such as sinter plant, basic oxygen furnace (BOF) cooling stack or reheating furnaces are considered in order to elaborate an integrated energy concept. Especially electric power generation is an attractive option for steel plant operators since it can easily be connected to the existing power grid of the steel plant. When direct local use of waste heat is limited, the best option is to convert it to mechanical/electrical power with a Rankine Cycle. A stand-alone system, compact design with minimum operational costs in order to fit into the existing steel plant layout, are the main requirements of such units. The objective of this paper is to demonstrate economic feasible opportunities for energy recovery for sinter cooler and basic oxygen furnace with focus on electric power generation via ORC modules taking at the same time advantages of CO2 reduction by utilizing waste heat from the process. Furthermore typical arrangements and layouts of such solutions as well as basic economic calculations will be presented in the paper.

Oct 30, 2017

By Adriane Lopes Mougo

Super duplex stainless steel presents a biphasic structure composed by ferrite and austenite with different characteristics and properties. In the micromilling process the cutting edge radius has similar dimensions to the grain size. The biphasic structure found in this material could influence on the cutting tool life and the surface integrity of the workpiece. Due to its low machinability, caused by high hardening level and low thermal conductivity, the process can produce built-up edge and high surface roughness (Ra). In this work it is performed an experimental study of the micromilling of super duplex UNS 32750 and the influence of the cutting speed (Vc) and feed per tooth (fz) on the surface integrity and tool wear. The design of experiments considered two levels and three replicates. Results indicate the increase of roughness for bigger feed per tooth, small influence of the cutting parameters on the burr formation. The tool presented flank wear after the experiments.

Aug 8, 2018

By Armando Vazquez

Steel Dynamics Inc. (SDI) and Tenova Goodfellow Inc. (TGI) have successfully commissioned the first hybrid extractive/laser system for continuous and full spectrum analysis (CO, CO2, O2, H2 and H2O vapor) on two twin shell furnaces at Butler, Indiana. NextGen® technology using off-gas analysis as a main tool for EAF practice optimization is a proven effective method for improving plant productivity. Significant benefits attributed to the NextGen® system are operational cost reductions through the use of real-time dynamic control of chemical energy and improved environmental conditions through reduced GHG emissions. Additionally, the implementation of Tenova’s Water Leak Detection Technology® has shown results as an effective tool for operators to identify in real-time the presence of water during both reducing and oxidizing conditions. This paper will include project details, trials and results and will also outline the latest hardware developments and multipoint capabilities

Oct 30, 2017

By Lesli Peterson

Spraying Systems Co® has continued to develop and evolve descale nozzles through the years. The most recent addition to the descale nozzle line, the DescaleJet® Pro, provides more impact and a more uniform distribution than previous descale nozzles. The improved performance has been achieved through multiple design changes such as a smoother approach, updated vane design and improved carbide orifice. In addition to providing improved spray performance the nozzle also lasts longer than previous versions. The new technology has been thoroughly tested in the lab using impact measurements and accelerated wear testing. In addition to lab testing the nozzle has provided improved performance and longer wear life for those that have made the change to the new technology. The new nozzle technology and the benefits to the rolling mill will be discussed.

Jul 30, 2018

By Rogério Felício dos Santos

Nitriding of metallic materials using electric discharges generated during electric discharge machining (EDM) is a recently developed technique. The aim of this paper was to correlate mechanical properties of a nitrided layer produced in AISI 4140 steel by EDM nitriding with the type and amount of nitrides. A conventional die-sinking EDM equipment and electrolytic copper electrodes were used to generate the electric discharges. The electrolyte was a solution of urea in deionized water. Knoop microhardness profiles assessed the variation of hardness along the nitrided layer, whereas the elastic modulus of this layer was measured using nanoindentation tests. Optical microscopy and X-ray diffraction (XRD) were used to characterize the nitrided surface. The results showed the formation of a nitrided layer containing iron nitrides with average thickness of around 25 µm. The amount of nitrides reduced from the surface towards the centre and these results correlated well with microhardness profiles obtained.

Jul 31, 2018

By Stefan Stein, Jorge Davo, Adrian Villanueva, Abhay Kulkarni, Shane Hoff

Pellet sizing plays a key role in the productivity of the entire pelletization and subsequent induration processes, whereas uneven pellet sizing can increase the circulating load of the balling circuit inducing operational instability leading to production loses. The present work focuses in comparing the agglomeration kinetics, expressed as the number of pellets produced in a determined target size range, of different organic binder-bentonite binder systems. The batch experimental results show that the binder system has a great influence in the resulting pellet sizing, which could lead to advantages in terms of balling circuit efficiency and eventually operational de-bottlenecking.

Oct 1, 2019

By José Fagundes Junior, Cleudson dos Santos Rego, Bruno Bastos da Silva Murad, Vitor Borlot Borba

Since the startup in 2002, the Hot Strip Mill at ArcelorMittal Tubarão has increased gradually the coil output as the customers demand new and more resistant dimensionally challenging (thinner and/or wider) steel grades. As a critical feature for customer applications, improvements have been carried out aiming a higher thickness performance and reduction of internal losses while still meeting the more restrict tolerances booked by the customers. This paper presents the recent thickness performance evolution since 2017 and the main actions deployed to improve it.

Oct 1, 2019

By Juliano Braz Possatti, Arnaldo Carneiro Salles, Cleudson dos Santos Rego, Leandro de Lucas Mendes

The increase in customer demand for steels with higher surface requirements, associated with the need to increase ArcelorMittal Tubarão's HSM productivity, it was necessary the development of controls and actions to reduce scale losses within the scenario of high productivity. This article describes the path followed by the hot strip mill team in order to reduce the occurrence and severity of scales.

Oct 10, 2019

By Rodrigo Fina Ferreira

This paper presents a mineral liberation study on two iron ore samples from the Quadrilátero Ferrífero, in Brazil: compact itabirite of low-grade metamorphism (CI) and friable itabirite of high-grade metamorphism (FI). The quartz liberation spectrum for both samples have been obtained through QEMSCAN analyses, carried out for several comminution degrees, to compare the liberation characteristics and to evaluate the evolution of the quartz’s liberation degree after fragmentation. The results have shown significant differences in liberation spectrum between the itabirite samples studied. The liberation process of FI was easier than of CI, due its high porosity and larger crystal size compared with CI, which has shown more complex mineral assemblages with low porosity and smaller crystals. The quartz liberation spectrum has shown that grinding at P95 of 0.210 mm for the FI sample, and of 0.045 mm for CI sample, should result in satisfactory liberation for subsequent concentration step.

Aug 1, 2018

By Luca Tommasi

Danieli complemented its wide range of production plants for the iron and steel industry with a further step upstream into iron ore pelletizing and beneficiation. Danieli has engineered and constructed a state of the art and fully automated pilot plant facility – pot grate and sinter box – at Altos Hornos de Mexico S.A. (AHMSA) Pelletizing Plant, Monclova, Mexico. Installation and commissioning were completed in October 2009. Key features of the pot grate include the avoidance of the need for operator intervention during the test, automatic system preheat, absence of dead time, heat recuperation system with an air/air heat exchanger, oxygen control in preheating and firing with zirconia oxygen analyzer, possibility to test deep beds up to 625 mm. A series of projects have been accomplished by AHMSA availing of the pot grate facility with the aim to enhance pellet plant productivity and to reduce operating costs. The results obtained by use of Danieli pot grate combined with the experience and skill of plant operators has shown significant technical and economical benefits thus fully justifying the initial investment made by AHMSA and confirming the importance of having an in-house testing facility in order to optimize industrial plant operations.

Aug 16, 2017

By Gerhard Richter, Norbert Asamer, Gerwald Decker

At various stages during their manufacturing processes - from casting to finishing before delivery - semi-finished steel and special alloy products must be cut and surface-treated as well. The requirements for the individual conditioning steps, however, can be quite different. For example, the work piece can be hot, warm or cold. At any rate, the product must always be perfectly prepared for the next manufacturing step - reliably, in the shortest-possible time and at the lowest-possible cost. For cutting and grinding, BRAUN has developed innovative technologies and highly flexible, tailor-made solutions which meet these requirements in the most optimal way. In particular, BRAUN’s cutting and grinding technologies can also be used for large-scale products.

Oct 1, 2019

By Diego Berti Salvaro

The morphology, dimensions and chemical composition of tribolayers strongly depend on the pressures and temperatures acting on the contact. They are formed by reactions between the surfaces in contact with each other as well as with the atmosphere, lubricants and possible contaminants. In this paper the influence of test time (180, 500, 1000 and 2500 h) into the formation and characteristics of tribolayers in pairs DLC-stainless steel tested under refrigerant gas R134a atmosphere without presence of lubricating oil was analyzed. The characterization was performed using scanning electron microscopy, energy dispersive spectroscopy (SEM-EDS) (morphology and chemical composition) and white light interferometry (dimensions). The tribolayers thicknesses ranged from 100 to 500 nm and they were composed by elements originated from mutual transfers between the tribological pairs as well as oxides, being more pronounced on the stainless steel surface. The results show that the tribolayers are chemically stable (maintained the same composition over time) and the thickness remained stable after a thousand hours of testing.

Jul 31, 2018

By Osvaldo Guilherme Comineli

An extensive investigation into the role of low copper contents on the hot ductility of C-Mn-Al steels has been carried out in order to better understanding the problem of “hot shortness”. Previous work has suggested that this problem results from the build up of Cu that occurs at the surface of the steel as a consequence of the preferential oxidation of iron. This causes the formation of a Cu-rich film of low melting point. A nickel addition has been reported as a solution to the problem, since it increases the solubility of copper in the austenite. After hot tensile testing to failure, samples of Cu-containing steels have been examined using optical, scanning and transmission electron microscopes. Recently published results indicate that copper, in addition to precipitating out as CuS, also segregates to MnS inclusions forming a shell around them. This does not seem to impair the hot ductility under an inert atmosphere, but may have serious consequences under an oxidising environment and lead to “hot shortness”. The influence of nickel in improving the hot ductility seems to be due to it forming a higher melting point alloy with the segregated copper. Data from this incomplete work also suggests that Ni reduces the precipitation of CuS particles. Current investigation carried out using confocal microscopy still to be completed will improve the understanding of the role of copper and nickel on the problem of “hot shortness”.

Aug 8, 2018

By Jorge Madias

Durante la laminación de barras y alambrones para construcción civil; perfiles y ángulos estructurales y barras redondas y hexagonales de aceros de corte libre puede presentarse la apertura de la punta o la cola y el estallido central, con la consiguiente parada y caída de la productividad, y pérdida de rendimiento metálico. En este trabajo se analizan las diversas causas que confluyen para que este problema ocurra. Se analiza la influencia de posibles defectos en las palanquillas, las características del corte de las mismas y otros problemas de calidad. Se revisa el rol del precalentamiento previo a la laminación, la refrigeración de los cilindros, el diseño de pasadas y la respuesta del material en función de su ductilidad. Se presentan diversos casos industriales para ilustrar las diferentes razones detrás del problema de la apertura de punta.

Jul 30, 2018

By Bruce V. Kiefer

A modernization project was undertaken by Kroman Celik Sanayii A.S. in order to improve their product quality, consistency and shape of the coil package, reduce maintenance and delays in rod mill, thereby increasing utilization and productivity. The project involved installation of a new Morgan Intelligent Pinch Roll and High Speed Laying Head, modifications to the existing controlled cooling conveyor, plus replacing the coil reforming station. The new pinch roll and laying head were to provide better control of the ring formation and consistency of the coil on the conveyor, while reducing delays on the conveyor. Changes to the controlled cooling conveyor included installation of new nozzle decks and Optimesh air distribution system along with re-arrangement of existing fans in order to improve both cooling rates and uniformity of cooling. This paper explains details and features of the newly-installed equipment technology. Resulting product and process improvements are presented, including increased tensile strength and uniformity, reduction in delays on the conveyor and reform tub, plus improvements in coil quality.

Oct 30, 2017

By Alain Denis, Marcelo Curtes Martins, Jeferson Rocio de Oliveira

In this work we present a study of optimization of a new inhibitor for turbulence pickling line. The efficiency of inhibition was measured and the weight of loss was evaluated in four different materials to optimize the dosage of the inhibitor. In seven months we had 8.7% of reduction in pickling losses.

Oct 1, 2019

By Kelen Juliane Mucelin

In order to better understand the tribological behavior of self-lubricating materials, Fe-Si-C matrix composites containing solid lubricants added during the mixing step were studied. The samples were produced by conventional powder metallurgy route, presenting total contents of 5%, 7.5% and 10% in volume of h-BN and graphite mixtures as solid lubricants. The composites were evaluated in terms of tribological properties, under reciprocating sliding conditions, and mechanical properties by using tensile tests. Additionally, the wear scars were characterized by Raman spectroscopy and scanning electronic microscopy. Higher total contents of solid lubricants greatly increased scuffing resistance however decreased mechanical properties. Furthermore, increasing h-BN contents reduces both properties. These results confirmed the applicability of such sintered composites as self-lubricating parts, reaching values up to 7000 N.m for scuffing resistance combined with ultimate tensile strength of 220 MPa.

Jul 31, 2018