Search Documents

By Adriano Gonçalves dos Reis

In the development of the structural materials for the advanced applications, as in the aerospace industry, there is a constant strive to increase both strength and toughness. Maraging steels are iron-nickel alloys designed to combine both properties that are achieved through the age-hardening of low carbon martensite. This alloy have a metastable martensitic structure that can revert to austenite when heated in temperatures close to the aging temperature, and this effect can be enhanced with the temperature increasing and time of treatment. Therefore, the study of creep behavior in elevated temperatures has technological importance to the development of this material. In this work the creep behavior of a maraging 300 steel solution annealed is evaluated by carrying out creep tests at 650ºC and in a stress of 200, 300 and 500 MPa. Creep parameters, such as steady state creep rate (?????), final creep time (tf), and stress exponent from secondary creep (n) are determined, considering that they are important to evaluate the creep resistance of the material.

Aug 7, 2018

By Jean François Stumper

This paper presents the TMT “3D TopScan” profilemeter, which is a Radar-based profilemeter that measures the total burden surface within a few seconds and on a continuous basis. This equipment is based on an electronically steered solid-state radar scanner, such that a very large amount of surface data is collected within short time intervals. These new electronically steered antenna systems are the key to meet the demands for both accuracy and speed. The TMT probe is installed at a fixed location at the top cone, such that it does not interfere with the charging, enabling a continuous measurement and a compact design.Blast furnace charging optimization can be achieved based on its measurement data. The burden surface is continuously measured every few seconds, enabling the blast furnace operator to detect any details including asymmetries or irregularities in the surface pattern. A variety of process analysis tools are available. Due to the continuous and fast measurement, the burden descent speed can be supervised without process interruption on an ongoing basis. More accurate process models (layer models) than ever are obtained which fully consider the unsymmetries.This technology, developed by TMT Tapping Measuring Technology, is successfully in operation at Salzgitter Flachstahl GmbH at their blast furnace B. The probe and the data evaluation tools combine today’s technological capabilities in measurement technology with the practical requirements of blast furnace operation.

Aug 16, 2017

By Ivan César Lopes Diniz, César Romero Afonso Goulart Júnior

Mandrels are tools applied to manufacturing seamless tubes. In VSB plants (Vallourec Soluções Tubulares do Brasil), it is used in two mills. Mandrel and PQF Mills. This is an expensive tool due its alloy (hot work tool steel – AISI H13) and lengh (between 12 meters and 22,5 meters). An opportunity to apply mandrels from PQF in Mandrel Mill has been identified. However, mechanical properties of PQF mandrels must be improved. This work presents the heat treatment process of Quenching and Tempering developed internally at VSB to improve PQF mandrel properties aiming to achieve Mandrel Mill requirements. Hardness and metallography tests were performed before and after some steps of the heat treatment to characterize and validate the process.

Oct 5, 2019

By Olivier Lacroix, Dubé Mathieu, Guylaine Laforest

The reduction behavior of iron ore pellets in gas-based DR shaft processes has been studied at COREM since the late 80s. At that time, a new DR characterization test called COREM R180 was developped in collaboration with ArcelorMittal Mines Canada (former Quebec Cartier Mining) and ArcelorMittal Long Products Canada (former ISPAT Sidbec Inc.). This paper describes COREM’s approach to improve its understanding of the relations between iron ore pellet microstructure and pellet quality. The differences between the DR90 and the R180 tests are discussed. The evolution of the microstructure during reduction of both tests is also described. The reduction steps during the two tests are put forward as an important factor impacting the microstructural changes as well as the test results.

Oct 1, 2019

By Daniel Stickel

Current political, economic and ecological guidelines demand the increase of power densities of nearly all machinery parts today. In order to further lower the wear rate towards the ultra-mild sliding wear regime an integral approach is needed, which has to regard contact conditions, surface topography, surface chemistry, as well as sub-surface properties. Still there are no simple parameters to classify the performance of tribosystem. In this study the area and volume affected by tribocontacts are calculated by means of a three dimensional elastic-ideal plastic contact model. The surfaces are generated by means of conventional machining procedures and characterized by scanning white light interferometry. The further input data as to normal and friction forces are derived by ultra-mild sliding wear tests under boundary lubrication conditions of carburized steel against carburized steel and 52100 steel against case-hardened spheroidal cast iron. This contribution will depict the distinct influence of the topography on friction and ultra-mild sliding wear of common Fe-base materials and point on the marked importance of highly localized effects, which govern the acting mechanisms.

Jul 31, 2018

By Bruno Alves Resende, Antonio Adel dos Santos

Temperature, microstructure and dimensions are the main material parameters to be controlled during hot rolling of steel. Although thermal mathematical models have long been developed and applied for hot strip rolling, each Hot Strip Mill (HSM) must have its own model adapted to its facilities. Thus, a mathematical model for temperature evolution during rough rolling has been developed for the Usiminas HSM at Ipatinga Plant. The model achieved a high level of accuracy, which was assessed by comparing measured values of temperature at the hot strip mill entry with the calculated ones, the difference ranging from 9°C to 17°C. Application examples have shown that the slab can be occasionally stopped before start of rolling for as long as a couple of minutes without compromising its further processing. On the other hand, if the transfer bar stops after rough rolling even for short time, further processing in the HSM can be hindered, due to excessive temperature drop. In case of such abnormal line stop, the model can be used as a tool for decision-making to either continuing the planned rolling schedule or to changing the route, thus improving the overall rolling process.

Oct 1, 2019

By Jan Lückhoff

The introduction of the EAF Quantum furnace by Primetals Technologies represents an important milestone in the field of electric steelmaking during the last 15 years. In this process the latent and chemical heat of the off-gas generated during a melting process in an EAF is used to pre-heat scrap in an integrated shaft prior the melting of the scrap in the vessel. Combining proven own technologies, Primetals EAF Quantum enables nearly continuous process, cutting down idle times and enhancing availability for production. The essential benefits will be shown in this Paper.

Aug 16, 2017

By Marco A. Ramírez-Argáez

A 2D mathematical model was developed for the plasma arc welding process. Computational simulations based on mass and momentum conservation equations as well as Maxwell equations were performed by using the commercial software PHOENICS. The model predicts the electric characteristics of the arc column, flow patterns, temperature contours and electrical potential, by varying the composition of the cover gas, in this case, argon and nitrogen. It was found that an arc of nitrogen with respect to one of argon generates more intense jets, greater voltages, and lower temperatures in the arc column for welding arcs current of 150 A and 10 mm arc length.

Oct 30, 2017

By Jean-François Stumper, Mario Moser, Mark Kruessmann, Volker Langer, Daniel Bastos Martins Cruz, Claude Meisch

The latest generation of probes and casthouse machines provide a wealth of data that has not been available a few years ago. The evaluation of this data gives direct feedback to improve the blast furnace efficiency, the equipment maintenance and design and it allows the early detection of critical or deviating process situations. A stable operation with lower operation and maintenance costs are the final customer benefits.

Oct 1, 2019

By Mery-Cecilia Gómez-Marroquín

O presente trabalho trata da formação da ferrita de zinco a partir da mistura e posterior reação solido-solido entre o óxido de zinco e óxido de ferro - Fe2O3 puros em proporções equimolares. A faixa de temperatura onde teve lugar a formação foi entre 1073 e 1373 K. Testes de redução da ferrita da zinco sintética-ZF e pós de aciaria elétrica–EAFD foram realizadas usando misturas de CO e CO2 que variaram entre 50 e 100% CO. Ambos os testes (formação e redução de ZF e EAFD) foram suportados usando técnicas de caracterização física, química, estrutural e microscópica. No caso da redução, foi observado que tanto a temperatura como a percentagem de CO, foram os fatores que, mais afetarem a redução de ferrita de zinco contida no EAFD. A máxima percentagem de redução da ZF foi 85%, para 100% CO, 1373K e 105 min, e 52%, para 50% CO, 1373K e 105 min. Por outro lado, atingiu o 100% para 100% CO, 1273K, em 80.75 min, 60%, para 50% CO a 1373K durante 105 min. no caso da redução do EAFD

Aug 17, 2017

By Mery-Cecilia Gómez-Marroquín

O presente trabalho trata da formação da ferrita de zinco a partir da mistura e posterior reação solido-solido entre o óxido de zinco e óxido de ferro - Fe2O3 puros em proporções equimolares. A faixa de temperatura onde teve lugar a formação foi entre 1073 e 1373 K. Testes de redução da ferrita de zinco sintética-ZF e pós de aciaria elétrica–EAFD foram realizadas usando misturas de CO e CO2 que variaram entre 50 e 100% CO. Ambos os testes (formação e redução de ZF e EAFD) foram suportados usando técnicas de caracterização física, química, estrutural e microscópica. No caso da redução, foi observado que tanto a temperatura como a percentagem de CO, foram os fatores que, mais afetaram a redução de ferrita de zinco contida no EAFD. A máxima percentagem de redução foi 85%, para 100% CO, 1373 K e 105 min, e 52%, para 50% CO, 1373 K e 105 min. Por outro lado, atingiu o 100% para 100% CO, 1273K, em 80.75 min, 60%, para 50% CO a 1373 K durante 105 min.

Aug 16, 2017

By Andreas Cestonaro

Roll grade evolution in plate mill applications is traditionally following the development in hot strip mills. New grades normally find their way into service only after being successfully implemented in hot strip production. The majority of the plate mills worldwide are using work roll grades that have been invented before the 1980’s. But today the demands in the mills are pushed by sophisticated product mixes and longer rolling campaigns. The result of this development is a higher wear rate on the work rolls and as a consequence roll hardness is increased and advanced roll materials are used. The backup rolls are also affected by this. The wear rate is higher and the mechanical impact in terms of contact pressure and work hardening is increasing. This paper outlines the results of the roll grade development at Gontermann-Peipers and introduces new materials for work and backup rolls for plate mills.

Jul 30, 2018

By Jens Kempken

A competitive landscape pressurizes the steel producers business, zero defect requirements from customers forces the operators for additional efforts in process control and quality management. The so called quality related cost, which include also rework, cost for downgrading or even scabbing of material is already a remarkable lever in a plants profitability breakdown. The introduction of advanced state of the art grades in the product portfolio requires already a budgeting for the expenses for R&D and quality management. PQA has been developed as a process and quality management software solution next to existing level 2 or level 3 automation systems. It is focusing on the analysis of process data, equipment information, in line quality measurement devices and trend analysis to obtain an answer whether the process is according to definition and expectation and whether the intermediate or final product can be shipped for further processing as prime material. Advanced analytics which are linked to an expert know how based configuration identifies deficiencies in the production and processing process. An intelligent, state of the art quality rating system evaluates tolerable deviations. PQA comprises the software platform including the database, data configurator and collector from the different sources in the production process and units. The core element of the platform is the knowledge based expert know how package defining process and quality determining fundamentals. The paper describes the structure of the software package, it gives insights on the expert know how package, process and quality evaluation and points out the customer benefits, cost reduction, improvement yield, customer satisfaction increase. The link to recent operational references is given.

Oct 30, 2017

By Diego Pacheco Wermuth

Micrometric surgical components typically have high geometric complexity and stringent regulatory specifications. These components need to have excellent mechanical properties and a high demand of products. Besides these factors, it is necessary to maintain a low manufacturing cost, performing essential research on new manufacturing technologies. Metal Injection Molding (MIM) is a process that has been explored , providing an interesting alternative for making medical devices. The research in the production of microcomponents obtained for MIM is gaining momentum and prominence, due to low cost and high productivity of this process. This paper is a study and development of feedstocks with AISI 316L alloy , which is known for its biocompatibility. Four feedstocks with 61%vol. of metal powder were analyzed by capillary rheometry and DSC/TGA.

Aug 16, 2017

By Andrea Pezza

The paper describes the recent new installation and start-up of the second RH (Recirculation Degasser) in Rio de Janeiro plant of thyssenkrupp CSA Siderúrgica do Atlântico. The new plant is installed as part of the existing RH, the twin solution increases the overall melt shop production in the area of quality plates especially for deep drawing grades. With this new equipment, CSA is able to increase degassed grades production with a state of art asset that has the ultimate technology in operation, safety and automation. The description of the main components parts and the operational concept gives an overview of the latest experience in RH plant engineering combined with best operational practice of world class steel producer.

Oct 30, 2017

By Christoph Sedivy

Industrie 4.0 is slowly but surely arriving in the melt shops. Furnaces are being equipped with more and more sensors, digital models are increasing the degree of automation, and information is being shared between different aggregates within the plant. Because the electrode control system plays a key role in electric steelmaking, it naturally assumes an important position in the melt shop’s Industrie 4.0 strategy. In addition to reliable, state-of-the-art core regulation functionality, monitoring and reporting tools and the ability to communicate with other equipment are also required. Therefore, the latest generation of our electrode control system, the Melt Expert, was developed based on Industrie 4.0 design principles. Intelligent plant condition diagnostics, performance monitoring, and user-defined reporting are essential modules in this new system. With these functionalities, electrode control systems are developing into the information and control center of the furnace. A newly developed software app brings most relevant process information to mobile devices. This feature allows steelmakers to keep an eye on the performance of their equipment anytime and anywhere. This paper describes the new features of the electrode control system and shares our customers’ operational experience. Our focus is on the practical aspects of plant status monitoring, KPI reporting, and diagnostic functionality as well as the improvements achieved.

Oct 30, 2017

By Mirko Jurkovic, Thomas Hueper, Jens Kempken

The high competition scenario pushes the steel producers business. Zero defect requirements from customers force the operators for additional efforts in process control and quality management. PQA® has been developed as an advanced process and quality management assurance solution. It is focusing on the analysis of process data, equipment information, inline quality measurement devices and trend analysis. The paper describes the structure of the advanced process and quality management assurance solution PQA®; it gives insights on the expert know-how, process and quality evaluation and points out the benefits like cost reduction, improvement yield and customer satisfaction increase.

Oct 1, 2019

By Gabriel R. Royo

This paper will cover a back up roll bearing technological upgrade, being implemented at the TERNIUM SIDERAR Hot Strip Mill (HSM), in San Nicolas, Buenos Aires, Argentina. This change was motivated by increased operating loads, which caused the original bearings to be outside the designed bearing rating. The problems were first identified by bearing seizures in some stands, and later followed by cracks forming in the back up roll neck areas due to fatigue and overload. MORGOIL engineers worked together with TERNIUM SIDERAR engineers in analysing the problem and to upgrade the mill with the newest and most economical technology. The upgrade consisted of changing the bearings to the latest generation MORGOIL bearing: the KLX, which within the same space, increases bearing capacity around 25%. This was accomplished re-utilizing all chocks. The new bearing allowed for a re-design of the geometry of the back up roll neck, making it much stiffer than the original design, and eliminating fatigue failures. In addition, an upgrade to hydraulic mounting and dismounting using the MORGOIL® HB lock was also implemented, as well as changing to the newest MORGOIL® HD seals. With the MORGOIL® KLX® upgrade, TERNIUM SIDERAR HSM increased load capacity, allowing them to roll products that were not even considered decades ago. Both older oil film bearings and roller bearing mills have been successfully upgraded while reusing existing chocks and in many cases rolls. Solutions are customized to the customer’s equipment and goals.

Oct 30, 2017

By Filippo Verlezza

The 3-roll technology is a recognized process applied to SBQ production. The main aim of this paper is to show the latest developments on this technology including other equipment´s that also contributes for a better performance on SBQ coils production.

Jul 30, 2018

By Ramon Augusto Moretti, Henrique da Rocha Severino, Renato Nascimento de Castro, Fernando Cesar Sousa

Rolling stand 12 (LTx) of long steel, installed in the company A, Piracicaba - SP unit, had presented high levels of vibration, which affected its internal components, such as: shaft, gears and bearings, generating downtime. To evaluate this equipment a study was proposed by the following engineering techniques: Conventional Vibration Analysis, Operational Deflection Shape (ODS) and numerical simulation by the Finite Element Method (FEM). In the Conventional Vibration Analysis, high levels of vibration were observed during manufacturing process, especially when the material reaches the equipment. Impacts generate high values in acceleration, on average 80 m/s² peak to peak. In the moment of impact, misalignment of internal components was observed by ODS. Field results were correlated to those obtained by the Finite Element Method, which allowed to calibrate FEM model. Thus, the most effective structural modification already numerically evaluated was implemented in the system. Afterwards, new measurements by vibration and ODS techniques were performed, and attenuation of vibrational levels and operational mode, which overloaded the internal components rolling stand, were verified.

Oct 1, 2019