Search Documents

By M. B. Standing, D. L. Katz

Density data are reported on 15 saturated hydrocarbon liquids in the range of 35° to 250°F. and 1000 to 8220 lb. per sq. in. The apparent liquid densities of methane and ethane are shown to vary with the density of the system in which they are present. A method is proposed whereby the densities of liquid hydro- carbon mixtures containing both methane and ethane in solution may be computed at elevated temperature and pressures within the accuracy of usual engineering computations. A method of computing the shrinkage of crude oils based upon the gas-oil ratio, gas analysis, and crude gravity is outlined. Introduction The densities of naturally occurring liquid hydrocarbon mixtures are important in many petroleum engineering computations. Calculation of the shrinkage of a subsurface sample of crude oil as the natural gas is evolved is one example of the use of liquid-density data. Sage, Hicks, and Lacey5 have presented a method of computing the density of hydrocarbon liquid mixtures based on partial molal volumes. Katzl has indicated a method based on the principle of additive

Jan 1, 1942

By M. B. Standing, D. L. Katz

Density data are reported on 15 saturated hydrocarbon liquids in the range of 35° to 250°F. and 1000 to 8220 lb. per sq. in. The apparent liquid densities of methane and ethane are shown to vary with the density of the system in which they are present. A method is proposed whereby the densities of liquid hydro- carbon mixtures containing both methane and ethane in solution may be computed at elevated temperature and pressures within the accuracy of usual engineering computations. A method of computing the shrinkage of crude oils based upon the gas-oil ratio, gas analysis, and crude gravity is outlined. Introduction The densities of naturally occurring liquid hydrocarbon mixtures are important in many petroleum engineering computations. Calculation of the shrinkage of a subsurface sample of crude oil as the natural gas is evolved is one example of the use of liquid-density data. Sage, Hicks, and Lacey5 have presented a method of computing the density of hydrocarbon liquid mixtures based on partial molal volumes. Katzl has indicated a method based on the principle of additive

Jan 1, 1942

By G. W. Reimers, S. E. Khalafalla

A colloidal solution of a ferrimagnetic material, such as magnetite, in a liquid that is immiscible with and lighter than water is projected for use in selective separation of particles according to their density spectrum. Magnetic levitation forces can be created as an antigravity field when the fluid is properly placed in an inhomogeneous magnetic field. When the gradient of the magnetic field is directed downwards, the levitation force in the fluid will be in an upward direction to float sinking nonmagnetic bodies by counterbalancing their density mismatch with the magnetic fluid. Several nonmagnetic objects with densities ranging from 2.50 to 11.35-g cm' were made to float or submerge at will in a 0.96-g cm' density fluid placed in vertical magnetic field gradients ranging from 0.1 to 1 kilo-oersted cm-'. The magnetic levitation force in dyne cm' was found to vary linearly as a function of the object-fluid density mismatch with a slope equal to one g, the acceleration due to gravity.

Jan 1, 1974

By M. Labrie, H. L. Gibson, G. Doiron, J. J. Watkins, D. H. Watkinson

The Corbet deposit is one of 17 proximal Cu-Zn massive sulfide deposits located. within the Noranda Cauldron which occurs within the core of the Noranda Volcanic Complex. The deposit is located at the top of the Havrian Formation, the lowermost formation of the 3000 m thick Mine Sequence; the deposit has Yielded 2.75 M tonnes of ore grading 3% Cu, 0.96% Zn, 2.06 g/t Ag and 1.0 g/t Au. The multi-lens Corbet deposit formed within a 250 m wide crater that occurs within a localized breccia pile. The Corbet breccia pile was constructed by explosive magmatic and hydrovolcanic eruptions localized along the south flank of a larger andesitic shield volcano that formed during the waning stages of Havrian volcanism. The breccia footwall of the deposit allowed unfocused and widespread hydrothermal discharge that resulted in the development of a large area of chlorite and fringing sericite alteration that exceeds, by six times, the size of the sulfide lenses and represents a significant exploration target.

Jan 1, 1993

By Jeongbok Seo

The Dulles Corridor Metrorail Project (DCMP) involves the design and construction of a 23.1-mile extension of the Washington Metropolitan Area Transit Authority (WMATA) rail system. The initial 11.7-mile extension, with five transit stations and a new service and inspection yard, is to be constructed. The construction plan for the initial 11.7-mile extension includes installation of a total of an estimated 4,250 or 160,000 linear feet of driven 12x53 steel H-Piles at more than 80 different locations. At the time of this paper, approximately 40 percent of the piles have been installed and the remainder of piles will be installed by the end of 2010. This paper describes: 1) subsurface investigation program, 2) application of existing Codes and impact on the design of H-Pile, 3) design methods to determine geotechnical bearing capacity and pile tip elevation, 4) verification of capacity including PDA and Static Load Tests, 5) project specific pile load tests, and 6) QA/QC during pile driving.

Jan 1, 2010

By Andrews S. J

Century is a shale hosted zinc, lead, silver deposit developed within gently folded, Proterozoic Lawn Hill Formation shales and siltstones, approximately 250 kilometres north-northwest of Mount Isa, comprising 118 million tonnes of stratiform mineralisation, averaging 10.2 per cent ,,inc, 1.5 per cent lead and 36 grams per tonne silver. The deposit is largely overlain by Cambrian limestone and younger Proterozoic sedimentary rocks, outcropping at only two places. Small discordant lode lead-silver deposits formed the basis of relatively small scale mining activity in the area for almost 100 years, exploration tenement covering the deposit being granted to CRAE exactly 100 years after the first mining leases were pegged in the area in 1887.Stratiform mineralisation occurs within three distinct blocks, bounded by normal faults and the unconformity between Lawn Hill Formation and overlying Cambrian limestones. The Termite Range Fault, a major northwest trending, regional scale fault system occurs adjacent to the northeast deposit boundary, while the Magazine Hill Fault, possibly a component of the east trending Little Range Fault system, forms the southern boundary of the deposit.

Jan 1, 1993

By L. C. IlsLey

"The maintenance of permissible equipment which is tested and inspected at the Pittsburgh Experiment Station of the United States Bureau of Mines is dependent to a surprisng degree upon the voltage at which the equipment is operated. The difficulty of maintaining 500-volt equipment is frequently brought to the bureau's attention, and it is quite possible that if the bureau had appreciated at the beginning the full hazard involved, it would never have undertaken the approval of equipment operating at voltages greater than 250 volts.In this connection, the following statement from State mine inspection departments and other sources are of interest as showing the general feeling in safety organizations with respect to voltages higher than 250. These statements, although obtained as a result of a questionnaire sent cut several years ago, still apply very well to present conditions.A. I have not had time to consider seriously the proposed change from every angle, but looking at it from a standpoint of hazard, feel that the danger would be greatly increased. I have always occupied the position that underground voltage on portable equipment should never exceed 250 volts.High voltage of course would mean smaller transmission lines, which would be more economical and no doubt would require in several instances smaller equipment; notwithstanding, if this statement is true, the writer is still favorable to low voltage on underground portable equipment.B. I believe 500 volts should be the limit on the best equipment ender the best conditions and that the U. S. Bureau of Mines should do all in its power to limit the voltage to 500 volts on permissible equipment, as any increase in voltage means increased hazard.C. I will refer you to a section of our mining law, entitled ""An Act to Regulate the Tine of Electricity in the Mines of the State of ----"" which reads in part, as follows: Trolley wires, or other exposed electrical wires, shall not carry a voltage above 275 volts.You may readily see by this that we are not permitted to operate mining machines under ground in -----, with more than 275 volts at the terminals, except that we are permitted to install transforming stations throughout the mines, after complying with certain regulations at the mine.However, as we have had to date, within the calendar year of 1925, six men electrocuted in the mines of the State, using a voltage of 275 volts, I am of the opinion that if this voltage was increased, the hazard would also be increased in proportion.D. I do not care to make a statement for publication: however, I am referring you to our mining laws. On page 27 and 28 you will find what the laws of -----¬require relative to the installation of electricity in the mines.""Hereafter where electricity is installed no higher than two hundred seventy-five (275) volts shall be used underground, except for transmission, or for application to transformers or other apparata, where the high-voltage circuit is stationary. High-voltage motors, and transformers, shall be installed in suitable chambers, built of fire-proof construction, and well ventilated, and shall not be placed on intake, or between intake and return air courses. All high-voltage lines lines and apparata must be clearly marked, to indicate their danger. Main and distribution switchboards for high voltage shall be made of insulating and incombustible material, such as marble or slate, and to be free of all metallic veins, or of material equivalent thereto. Same shall be installed in a dry place. All switches or other instruments used in connection with high voltage shall be installed on suitable switchboards, with at least a three-foot passageway in front and rear properly floored, and kept looked by a door at each end that can be opened from the inside without a key. With higher than medium voltage, there shall not be any live metal work on the front of switchboard, and the entry circuit must be protected by an oil breaker s"

Apr 1, 1932

By Joseph W. Murray

Prior to 1950 Magma's ore production came from two parallel, steeply dipping, east-west striking mineralized faults, one called the Main or Magma vein and the other the Koerner vein, which lay about 1100 ft to the south. This vein system has been explored and mined over 9000 ft horizontally and 4800 ft vertically. In 1950 continued exploration led to the discovery and development of replacement orebodies in the Devonian limestone zones adjacent to the veins. These replacement deposits occur in the eastern part of the Magma mine and follow the strike and the 30º east dip of the host limestone. Strike length of the ore bodies varies from 250- 500 ft and thickness from 15-125 ft. The orebodies are large tabular masses with chalcopyrite and bornite being the dominant ore minerals. Hematite and pyrite are the most abundant gangue minerals. Incompetent limestone, shale, or a porphyry sill hanging wall is characteristic of portions of the replacement beds. In many instances the ore is blocky, badly fractured and intermixed with layers of limestone gouge, pyrite and hematite.

Jan 6, 1973

By James L. Noble

A small placer operation can be defined as one with a throughput capacity of 250 cubic yards an hour or less. The success of small placer operations after the values have been established, depend entirely on having the proper design. There are various types of placer deposits including marine, beach, desert, stream, bench, underground and even frozen placers. Each is unique and requires special considerations. Size distribution of alluvial placer ore varies from sand to large boulders. When boulders occur, they can become a problem to all types of excavating to a greater or lesser degree. Clay content and cementing are common in placer deposits. Some clay disperses easily in water while others, if not handled properly, will form clay balls that pick up gold and carry it to tailings. Overburden, depth of bedrock, vegetation, and ground and surface water must all be considered when designing a plant. Any equipment chosen should be capable of processing large volumes of material at a high efficiency. There are usually five steps to processing placer gravels, as follows:

Jan 1, 1992

By K. Morsy, S. S. Peng

This paper deals with the causes and mechanisms of massive pillar failure in a room-and-pillar mine that employed nine-entry panel system using supersection technique under a cover ranging from 91 to 168 m (300 to 550 ft). Chain pillar squeeze and large roof-to-floor convergence were first observed at the belt transfer point on the very inby side of the main entries. It propagated outby quickly and within 24 hours it had covered an area approximately 1,250 m long by 762 m wide (4,100 x 2,500 ft). The failure was caught and stopped by a solid barrier pillar. Using computer modeling, the study indicated that the massive failure was initiated due to a combination of undersized chain pillars in some panels and weak immediate floor. Also, the study shows that the massive pillar failure expanded to a large area because of no barrier pillars between some panels and between mains and panels. Based on the computer modeling, alternative mine plans have been proposed to avoid such problems.

Jan 1, 2000

By M P. Sandy

Some Western Australian underground mines are challenged by very high stress gradients. This environment frequently results in poor induced ground conditions and damaging seismic activity. In some cases, rockbursting or squeezing ground has been observed as shallow as 250 m below surface. Very few mines operating at depths greater than 500 m experience no stress-related issues. As a general result of this difficult environment, there are a growing number of mines that are now challenged or have been closed by induced geotechnical problems. Often, the up-front savings or perceived advantage of an inappropriate mine plan may be entirely lost to the real cost of managing the hazards, or a write-down of reserves resulting from access difficulties will diminish the economic position of the mine. From an engineering perspective, it is best if stress-related hazards can be proactively minimised, because reactive measures offer less improvement in risk exposure. In this paper, some examples of sequencing techniques for managing difficult environments are contrasted with examples from mines where developing hazards have adversely affected production or the economic viability of the project.

Jan 1, 2003

By J. Bender

The objective of this research was to (1) Further develop cyanobacteria mats' for metal-tolerance and cold-tolerance, (2) test them for durability in the field environment and (3) assess them for metal sequestering potential with actual and simulated field samples. Results show that mats performed well In the field and effectively sequestered metals from actual and simulated field samples. Metal uptake from Iron Mountain Hine samples was for Ins 87%, Cu and Cd 99%, Initial concentrations (mg/L) were Zn = 3,250, Cu , 279, Cd = 28. In solutions simulating the Gulf Tunnel drainage, Zn and Mn were effectively removed by mats immobilized on glass wool. Effluent water, after treatment, generally had a Ph of 7 .5-8.5. Al though the final metal concentrations in the mats 'harvested from the decontaminated water were only 1% or less, the actual mechanism of metal deposit was probably a mat-mediated alteration of the environmental conditions causing the metals to deposit outside the mat as oxides or carbonates. Bioflocculents, released by the mats, were likely involved in the metal-removal process.

Jan 1, 1996

Firedamp drainage has become an essential part of many mine environmental systems, and new applications are arising. Installations are evolving further to satisfy ever changing basic requirements, standards, and iniilny needs. In this paper, water seal, vacuum based installations are considered, as well as moni- toring, protective and control systems which have been developed for continuous, manless, and trouble free operation. Some factors affecting plant capacity and extractor per- formance are identified and assessed. INTRODUCTION Firedamp drainage applications are incr- easing world wide as mining engineers strive for improved safety and security, and further concentration of coal output. Fewer and fewer mines are able nowadays to satisfy coal prod- uction and firedamp control requirements solely by air dilution or by air dilution and underground firedamp extraction plants. As a result, dependence on surface extraction plants is increasing. This paper deals with som requirements and applications of such installations. I. DEVELOPMENT AND PRACTICE Firedamp drainage has existed for over 250 years following the early work of Carlisle Spedding at Whitehaven (1730). Some fundamentals of current firedamp drainage systems can be recognised in the

Jan 1, 1982

By D. G. Kesterkel

Low-melting thoriurnrbase binary alloys or metal solutions were prepared by two different techniques involving the electrolysis of ThO2 dissolved in fluoride melts. Experiments were performed at 950° to 1,250° C using electrolytes containing ThF4 and various alkali and alkaline earth fluorides. In the first method, electroreduction of ThO2 and deposition of thorium on a nickel or iron cathode formed a molten alloy that dripped off and collected on the bottom of the cell, or in a tungsten cup. An electrocodeposition technique was used to prepare thorium-base alloys or solutions containing nickel, iron, chromium, or manganese. Electrolytic reduction of the component metal oxides and simultaneous deposition of the two metals on a tungsten cathode yielded a liquid alloy product. Complementary experiments were performed on the fused fluoride electrowinning of dendritic thorium from Th02 at 1,075° to 1,200° C in which thorium crystals were recovered and arc-melted into buttons. Major contaminants were aluminum, carbon, copper, iron, oxygen, and silicon, totaling 0.2 percent.

Jan 1, 1966

By Lai KF

The Hellyer orebody is a fine grained, massive sulphide Pb-Zn-Ag- Cu-Au deposit located in western Tasmania. Initial testwork showed that the orebody would be difficult but not impossible to treat by conven- tional flotation. A staged programme-of work was commenced to demon- strate that marketable concentrates could be produced with satisfactory recoveries. Following laboratory testing of drill core to define two flowsheets, bulk samples of Hellyer totalling 20,000 tonnes were trialled at 6 tph in the Cleveland concentrator over six months. The high through- put and extended duration of the trials ensured maximum confidence in the results and that scale-up to subsequent plants would be with a mini- mum of risk. The milling trials were successful and the Cleveland concentrator was expanded in early 1987 to treat 250,000 tpa of Hellyer ore to produce 85,000 tpa of bulk concentrates. Late in 1987 construction commenced on a 1 mtpa concentrator at Hellyer to produce separate copper/silver, lead, zinc and bulk concentrates.

Jan 1, 1988

By William B. Plank

THERE are 19 pct fewer undergraduate and graduate mineral engineering students enrolled in the ECPD accredited schools of the United States this year than there were a year ago. The figures are: 8727 this year and 10,674 last year. The entire engineering group in both countries numbers 171,070, as compared with 184,547 last year and 252,250 in 1947-48, the peak year. This is a decrease of 7.3 pct since last year, less than half as much as the decrease in the mineral engineering group. These figures on engineering enrollment for the current year, 195.1-52, in colleges of the United States and Canada were prepared jointly by the U. S. Office of Education and the American Society for Engineering Education. The seriousness of the situation is shown. by the reported demand for 60,000 to 90,000 engineers this year for civilian and defense industries and only 35,800 will graduate next June. Many of the 1952 graduates are subject to Selective Service, having been granted deferments while in college, and ac- [ ]

Jan 1, 1952

By Cyril Smith

THE following table, which is composed of data given in the author's first paper on the thermal conductivity of copper alloys1, contains the results which have been obtained by previous workers on the thermal conductivity of the copper-tin, the copper-phosphorus and the copper-tin-phosphorus alloys (the phosphor bronzes). TABLE 1.-Previous Investigations Composition, Per Cent. by Weight Thermal Conduc¬ Investigator tivity, Cal/Sq. Cm./ Copper Tin Phosphorus CM./Sec.. °C. Hardebecka 95.0 5.0 0.176 (20° C.) Grossmanb 90.1 9.9 0.105 75.5. 24.5 0.059 24.9 75.1 0'.139 (13° C.) 9.7 90.3 0.131 0.0 100.0 0.142 Griffiths and Schofieldc 91.7' 8.0 0.30 0.108 87.2 12.4 0.40 0.087 (20° C.) 90.0 10.0 Small amt. 0.100 Donaldsondd: 87.8 1 11.3 0.35 0.128 Pfleiderere 99.4 1 0.63 0.250 (30° C.) 98.0 1.98. 0.125

Jan 1, 1930

By A. T. Weber, G. T. Adel

Earlier studies on the hydrodynamic interactions between fine particles and air bubbles have shown that fine particle flotation can be improved by using small air bubbles. In the present work, microbubbles ranging in size from 70 to 250 microns have been used in a flotation column for the processing of fine coal. The performance of the microbubble column has been studied as a function of wash water addition rate, aeration rate, feed rate and column length to diameter (L/D) ratio. The information collected from these tests has been used to analyze column behavior and to develop scale-up criteria. The results of this investigation suggest that mixing within the column may not be as significant as bubble size and residence time in determining column performance. Improved recovery can be obtained by decreasing bubble size which increases the flotation rate constant, and also by increasing L/D which increases residence time for a fixed column volume. The increase in residence time with L/D is due to a decrease in the volumetric flow rate of wash water with column diameter.

Jan 1, 1988

By Jose F. Agapito

This paper describes part of a geotechnical program which was instrumental in obtaining information for the design of large oil shale pillars. The work was carried out during 1971 and 1972 in the experimental mine of the Colony Development Operation. Colony is an oil shale venture formed between Atlantic Richfield Company, Operator; The Oil Shale Corporation, Cleveland-Cliffs Iron Company, and Sohio Petroleum Company to conduct research and development in mining and retorting of oil shale. The property is located in the southern edge of the Piceance Creek Basin in northwestern Colorado, approximately 250 miles west of Denver. Mining was conducted by the room-and-pillar method in a 60-ft high portion of the Green River formation at a depth of 600 to 850 ft. Pillar dimensions are approximately 60 ft by 60 ft. The mine site is in the eastern face of the canyon containing the Middle Fork of Parachute Creek. The distance from the mine to the side of the mountain varies from 500 to 1200 ft, and its height above the stream floor is approximately 700 ft.

Jan 5, 1974

By Albert F. J. Bordeaux

The following general survey of the character and present condition of the silver-mines of Mexico, though not offered as a detailed treatise, has been prepared with care, is believed to be generally up-to-date, and is offered as a summary which may be found useful by mining engineers. For several centuries Mexico has ranked first anlong the silver-producing countries. It is now second as a copper-producer, and seventh as a gold-producer, with a fast-increasing output every year. The total amount of capital invested in its mining- and smelting-works exceeds $250,000,000, while the value of the yearly metallic production is $160,000,000. There are more than 20,000 recorded mining properties. The silver-mines of Mexico represent deposits of three principal classes: (1) veins and stock-works in eruptive rocks; (2) fissure-veins crossing the crystalline schists, granite, diorite, etc.; and (3) veins and replacement-deposits in limestone. The true fissure-veins in some districts contain (in value) vol. xxr1x.—22

Jan 1, 1909