Search Documents

By Whiten W. J

An investigation on the breakage characteristics of closely sized orc samples at different levels of input energy was carried out to determine an appearance function for possible use in ball mill modelling. A consistent pattern of breakage behaviour was observed and the resultant size distributions could be described by a one-parameter, ('t'), family of curves. For each particle size range tested, this parameter 't' has an exponential relationship with input energy below an upper energy limit. A tentative linear relationship between the input energy at a constant value of 't' and the work-index leads to reconstruction of 'I' - input-energy curves from the work-index values. To normalise the efrect of particle size and input energy, multidimensional cubic spline regression was performed on thc entire range of data. The results indicated that the parameter 't' can be determined, reasonably accurately, as a function of Ln (input energy, kWh/tonne) and Ln (particle size, mm) for input energies between 0.5 and 8.0 kWh/tonne.

Jan 1, 1983

By A. A. el-Geassy

High-grade iron ore fines rejected from the DRl plants (>96%Fe20) were isothermally reduced in 30-60%COIH2 gas mixtures at 973-1273K. The freshly reduced reaction products were then subsequently carburised in either H2/CO or H2/CO/S mixtures at 823-1073K for 30-120 min. The thermogarvimetric technique was used to follow up both of reduction and carburisation reactions as a function of time. The carburised samples were characterized by X-ray and Mossbauer techniques. Chemical and carbon analyses were also applied. The influence of temperature and gas composition on the reduction behavior was investigated. The calculated values of apparent activation energy, application of gas-solid mathematical formulations were correlated with the microstructures to predict the reduction mechanism, The influence of carburization time, temperature, CO contents in H2/CO or H2/CO/S were investigated. A conversion extent of Fe to Fe3C was taken as a measurable index for the efficiency of carburization reaction under the different experimental conditions.

Jan 1, 2003

By A. A. EI-Geassy

High-grade iron ore fines rejected from the DRI plants (>96%Fe2O3) were isothermally reduced in 30-60%CO/H2 gas mixtures at 973-1273K. The freshly reduced reaction products were then subsequently carburised in either Hz/CO or H2/CO/S mixtures at 823-1 073K for 30-120 min. The thermogarvimetric technique was used to follow up both of reduction and carburisation reactions as a function of time. The carburised samples were characterized by X-ray and Mossbauer techniques. Chemical and carbon analyses were also applied. The influence of temperature and gas composition on the reduction behavior was investigated. The calculated values of apparent activation energy, application of gas-solid mathematical formulations were correlated with the microstructures to predict the reduetion mechanism. The influenee of carburization time, temperature, CO contents in H2/CO or H2/CO/S were investigated. A conversion extent of Fe to Fe3C was taken as a measurable index for the efficiency of carburization rcaction under the different experimental conditions.

Jan 1, 2003

By Ryokichi Shimpo

Much amount of sludge is produced from the wastewater treatments in surface finishing industry. There are many problems for the abandonment of the sludge because of the high water content and heavy metals included. It is often observed that hexavalent chromium, which is toxic, is generated in the course of heat treatments of the sludge for reducing its amount by dispersing water. In this study, conditions of the sludge calcinations for reducing water contents have been examined. Maximum hexavalent chromium generation was observed in the temperature range around 773 K, at which most of the crystallization water decomposed from the sludge. When the heating temperature became higher than 1173 K, the amount of the hexavalent chromium extracted from the calcined sludge became as low as 10 mg/kg sludge. When the sludge was heated with iron oxides, FeO or Fe203, iron ferrite has been synthesized which may be used as a magnetic material. The amounts of hexavalent chromium generated in the heat treatment with iron oxides were not much different from those without iron oxides.

Jan 1, 2003

By P. A. Bahri, D. G. Dixon, T. M. Woodward

A comprehensive mathematical model of the Sherritt-Gordon ammoniacal pressure leaching process at K winana Nickel Refinery has been constructed. The process is comprised of six autoclaves functioning as a three-stage leach circuit, operating over the temperature and pressure ranges of 85-95°C and 750-1000 kPa, respectively. The process chemistry forms a complex series-parallel reaction network, characterised by: (1) the gas-liquid mass transfer and reduction of oxygen, (2) the oxidation of eight distinct minerals, (3) the oxidation of sulphur, and successive reactions involving various intermediately oxidised sulphur species, and (4) the oxidation of Fe(II) to Fe(III), and subsequent precipitation as a hydrated ferric oxide. Material balances were developed for species in all three phases, and an energy balance to account for all reactions and phase conversions. The multiple convolution integral (MCI) statistical reactor model was employed for the scale-up of particle kinetics. The model has been validated against plant data, and simulation results are in agreement with plant performance.

Jan 1, 2005

By Lloyd R. Nelson

Experimental results of three-phase mixing in a physical model of a CCRL for metals refining are presented. The system was operated above a critical lower liquid height-to- width ratio (H,/W) of unity, with adequate bottom gas injection through a line of central, single tuyeres (Q,/A = 7.5 cm/min, or c = 17 W/m3) to sustain levels of interphase transport considered appropriate to an industrial pyrometallurgical refining operation. The application of a thermal tracer technique to elucidate both longitudinal mixing and interphase heat transfer is discussed. The results indicate that even under conditions of significant bottom gas injection, it should be possible to maintain acceptably low longitudinal mixing 1 (D, < 20 cm /s and D,/uL < 0.1) in the CCRL. Interphase mass transfer coefficients of the order of 0.004 cm/s are predicted from the measured interphase heat transfer coefficients (h = 1.3 to 2.0 kW/m2K), using the heat and mass transfer analogy. Adequate rates of rehning are predicted for an industrial CCRL operated under such conditions.

Jan 1, 1995

By Paolo Bevilacqua, Paolo Antonini, Lorenzo De Lorenzi

"Ceramic production requires large quantities of K-feldspar, which is commonly sourced from granites, alkali-granites, and feldspathic sands. These rocks contain other minerals, such as quartz and plagioclase, which are undesirable for ceramic production. Due to the coarse mineral grains that constitute these rocks, a reasonable liberation is achieved at a relatively coarse particle size.The feasibility of feldspar-quartz separation using a dynamic dense medium separation system has been investigated as an alternative to flotation techniques. The use of a two stages cylindrical vessel (Tri-Flo) was preferred to a conical vessel, due to the improved separation efficiency.In a full-scale processing plant, a dense medium separation process can be used as a K-feldspar preconcentration step. This reduces the amount of material to be treated in the more expensive processes, such as finer comminution, flotation or magnetic separation.A comparison between commercial raw materials for the ceramic industry and the “rich in feldspar” products of the Tri-Flo process is reported, and the validity of the process is demonstrated."

Jan 1, 2003

By Dimitrios Fillippou

Magnesium hydroxide is used in a number of industrial applications, from the neutralisation of acid effluents to the production of pharmaceuticals. High-quality magnesium hydroxide powders can be produced by hydrating slow-reacting magnesia in dilute magnesium acetate solutions. The process of magnesia hydration shows many similarities with a typical hydrometallurgical leaching operation; however, its kinetics are crucial not only for process design and control, but also for the production of powders with a desirable particle morphology. This article shows the results of an experimental work whereby industrial heavily-burned magnesia powders were hydrated in 0.01 to 0.1 mol/L magnesium acetate solutions at temperatures ranging between 333 and 363 K. Examination of the magnesium hydroxide produced and the analysis of the kinetic data suggest that the hydration of heavily-burned magnesia in magnesium acetate solutions is a dissolution-precipitation process controlled by the dissolution of magnesia particles. The activation energy was estimated to be 60 kJ/mol, while the reaction order with respect to magnesium acetate concentration was found to be about one.

Jan 1, 1999

By R. C. Hubli

Copper (II) chloride has proven to be an efficient lixiviant for copper sulphide ores and secondary sources of copper such as scrap. Nickel sulphides are generally associated with copper ores and copper-nickel matte is an intermediate product of processing mixed sulphides. While the copper species in aqueous chloride media are present as chlorocomplexes, the presence of nickel as Ni++ offers effective separation between the two by solvent extraction techniques. Oxidation of millerite by cupric chloride in sodium chloride solutions has been studied as a function of rate of agitation, leaching time, temperature, acid concentration and total initial cupric concentration. The reaction has a 1/2 order of dependence on initial cupric concentration in the range of 0.0 to 0.5M. The activation energy for the temperature range 333 -363 K has been found to be 59.2 kJ/mol with chemical reaction at the unreacted mineral surface as the rate controlling step. The rate expression, according to the shrinking-core model, for initial cupric concentrations between 0.0 to O.5M, is evaluated as

Jan 1, 1996

By J. Ji

Oxygen requirement during acidic pressure oxidation of sulphide concentrates can he as high as 800 kg/(m3.h) in the first compartment of an autoclave when the total oxidation residence time is shortened to 30 minutes. To achieve such a high oxygen transfer rate while maintaining satisfactory oxygen utilization, a pilot plant campaign was launched at the Placer Dome Research Centre in 1998 to measure the oxygen mass transfer coefficient in a 5 m3 pressure vessel at a total pressure close to 500 psig with a 30 HP gassing agitator. Maximum oxygen flowrate to the pressure vessel was designed at 3 600 kg/h. In this paper, a great deal of information is provided on the gassing agitator, pressure vessel. measurement procedure and results. Without oxygen sparging, the oxygen mass transfer coefficient is 2 600 h-1 with a mixing power input of 5.0 kW/m3 in solution. With oxygen sparging, the oxygen mass transfer coefficient increases to 3 500 h-1 with a mixing power input of 4.0 kW/m3 in solution.

Jan 1, 2004

By Eugie Kabwe

The effective employment of a pretensioned bolt within support structures requires an appropriate installation tension as a result of sufficient bolt head/nut preload. In this paper, a load indicator washer (LIW) able to withstand an assigned static loading as well as provide an appropriate pretension is presented. The different LIW breadths are numerically analyzed with ABAQUS finite-element code to estimate deformation when a designated 60 kN preload is applied. The numerical simulation employs the bilinear isotropic hardening constitutive law governed by the von Mises yield criterion. The simulation also considers the nominal temperature of the nut-LIW-rock bolt connection. Therefore, long-term relaxation effect on bolt pretension as a result of stress relaxation is neglected. The compressive force required to achieve the LIW predetermined deformation is the bolt pretension. It is drawn from the simulation results that LIWs with thicknesses of 1.5, 2.0, 3.0, 3.5 and 4.0 mm are completely flattened when subjected to 28, 42.5, 65, 76 and 88 kN preloads, respectively.

By F. C. Yi

Discontinuous and consecutive process was applied to probe into the Kinetics and adsorption theory for Cs+ adsorbed by Zeolites under the conditions of temperature, time and fixed-bed dynamic adsorption. It indicated that the sorption kinetics behavior of zeolite?s sorption on Cs+ is ac-cord with pseudo-secondary velocity equation, velocity constant k2=0.0005213 g?mg min-1, and equilibrium adsorptive capacity is 147.0588 mg?g-1; The equation can be expressed as: Y=0.0068X+0.0887; From the analyzing of diffusion coefficients on different temperatures and times, the coefficient of diffusion is not only related with the fabric of mineral and the character of ions but also the temperature and time; When the ambient temperature hoisted, the diffusion velocity augmented rapidly; Cs+ would get over a certain energy barrier when it enters into structure of zeo-lite; This energy is expressed by activation energy, and its value is E=131.668818 kJ?mol-1; There are two dominating adsorption mechanisms in the system of zeolite absorb Cs+: ionic interchange and surface coordinate adsorption.

Jan 1, 2014

By M. Mohan Rao

A Sievert &apos; technique was used. The few determinations made on 10 per cent and 20 per cent V alloys did not show any deviations from Sieverts&apos; law up to I>N2 = 1 atmosphere. The same held true for alloys of 0.2 per cent Ti. Nitrogen absorptions in Fe-Ti alloys, containing from 0.50 to 0.77 per cent Ti at 1,600°C, follow Sieverts&apos; law at low PN2 values, but, due to the formation of a delta titanium nitride phase, deviate from this law beyond critical values of PN2? There is evidence that this phase is Ti1.1N. The behavior observed can be described by the followmg equations: Ti,.,N(o) = 1.7Ti + N K = (fT; ? % Ti)1?7 (f;;.? %~_) = 0.0020 K = fN. %~ = 0.042 &apos;\)-:>N 2 I NTRODUCTJON Nitrogen&apos;s solubility in liquid iron-vanadium alloys was investi-gated briefly by Brick and Creevy ( 1), and more extensively by Kash-yap and Parlee (2) and by Pahlke and Elliott (7). Nitrogen&apos;s solubility in liquid iron-titanium alloys

Jan 1, 1963

By Mason D. O, Tuckwell K. D

Whole rock geodhemical analyses from samples of Potosi gneiss within the Willyama Supergroup have been utilised to identify geochemical trends towards Pb/Zn ore positions. Although the analyses come from disparate sources they have been incorporated in the data base only if locational, sampling, analytical, lithological and stratigraphic descriptors were reliable. These data have been statistically analysed using programmes of the GASP software package. A discriminant function has been derived which permits Potosi gneiss associated with the Pb/Zn lode horizons in the Broken Hill domain to be distinguished from Potosi gneiss in a similar stratigraphic position in the Maybell Domain. In the "near ore" position the Potosi gneiss has significantly lower mean Na2O and significantly higher mean MnO. Also mean Rb, CaO and K20 are higher and mean Sr lower. This discriminant function serves to identify areas prospective for Pb/Zn mineralisation. A second discriminant function based on MnO, Si02 and K20/Na20 gives a semi- quantitative indication of proximity to ore.

Jan 1, 1983

By L. A. Haas

Hydrogen sulfide was decomposed to elemental sulfur in an electrical discharge. With He, N., or Ar diluents, a threshold voltage between 1 and 3 kV was required for the decomposition reaction to occur in a laboratory ozonizer. Above the threshold voltage, the HAS decomposition rate increased with increasing voltage, but the increase was more pronounced with argon diluent than with either nitrogen or helium. In common with other reactions in an electrical discharge, the B2S decomposition decreased with increasing temperature in the range of -410 to +61° C. The reaction did not appear to be rate-controlled by a solid-gas sorption step because the introduction of activated charcoal into the electrical discharge zone did not significantly affect the decomposition yield. In the presence of polymeric chlorofluoro-carbon oil, 90 pct conversion of the 3 pct H2S in helium was obtained at 14 kV, 60 Hz, a 2-mm electrode gap, and a gas-residence time greater than 1 min. Under the same experimental conditions in the absence of oil, the conversion was only about 50 pct.

Jan 1, 1973

By Wagner Angelo da Silva

A crescente demanda por energia elétrica nas aeronaves modernas pode ser constatada pelo aumento da potência elétrica gerada a bordo, como exemplo o Boeing 787 produz 1000kVA, 200V trifásico, 400Hz variável contra 240kVA, 200V trifásico, 400Hz fixo produzido pelo Airbus A330, apesar de possuírem aproximadamente as mesmas dimensões. Devido à necessidade de redução de massa de transformadores, a frequência utilizada na geração de eletricidade na aeronave é de 400Hz o que acaba produzindo um aumento das perdas em núcleos de FeSi destes transformadores, principalmente pelo aumento das correntes parasitas no núcleo. Transformadores elétricos com núcleos de ligas amorfas a base de Fe vêm apresentando redução de até 70% das perdas no núcleo quando operados em 50Hz ou 60Hz. Assim, esse estudo visa discutir as vantagens e desvantagens do uso de transformadores elétricos com núcleos de ligas amorfas a base de Fe em aeronaves. Os resultados mostram que, com o desenvolvimento de novas ligas, tal utilização mostra-se viável devido a uma redução de peso de tais transformadores.

Aug 8, 2018

By Williams C

A stibnite concentrate from Golden Spec (WA) was subjected to a series of tests involving high pressure cyanidation and pressure oxidation followed by conventional cyanidation. The concentrate, whose gold content was 18.1 g/t, yielded only eight per cent of the gold when leached directly by a standard 24-hour cyanidation test. The recovery was increased to only 15 per cent when pressure cyanided under the following conditions: ambient temperature, 2000 kPa oxygen pressure, two hour retention time and 30 per cent w/w solids pulp density. This poor response to pressure cyanidation emphasised the refractoriness of the material. Evidence of the fine distribution of the gold through the concentrate, from measurements of the particle sizing distribution and the gold analyses of the individual fractions, also suggested that this concentrate was highly refractory. Pressure oxidation of the concentrate at elevated temperatures followed by cyanidation yielded recoveries as high as 94 per cent. However a preoxidation treatment under the following conditions was necessary: 230¦C, 2000 kPa oxygen pressure for a period of four hours.

Jan 1, 1992

By N. Bazzanella

The hydrogen desorption kinetics of pure and Nb-doped magnesium hydride film samples was investigated by using a Sievert-type apparatus. The overall activation energy and the reaction order controlling desorption are (141±5) kJ mol-1H and n 4 for Mg hydride and (51±5) kJ mol-1H and n 1 for Nb-doped (5% at) Mg hydride indicating that, in the doped sample, hydrogen desorption is controlled by the H migration in transformed h-Mg layers. Structural analysis performed by X-Ray Diffraction (XRD) and Extended X-Ray Absorption Fine Structure spectroscopy (EXAFS) show that the catalytic effect of the Nb dopant is connected with the formation of NbH0.89 nanoclusters dispersed in the Mg hydride matrix. It is suggested that the catalysis process is also connected to the presence of Mg-Nb hydride interfaces where the transfer of H atoms preferentially occurs by connecting h-Mg grains and by the role of the MgH2-NbH0.89 interface as preferential site for the dissociation of the hydride phase.

Jan 1, 2006

By W. Joseph Schlitt

The characteristics of successful heap and dump leach operations are first reviewed in a general sense. Then attention is focussed on solution management as the key operating parameter in leaching. The first part of this study includes a detailed conceptual analysis of fluid flow. This identifies the relationships between the flow parameters and the chemical and physical properties of the rock. Then these relationships are extended to practical systems in order to establish optimum application rates and solution distribution methods for heaps and dumps. The study shows that there is a maximum effective application rate, qmax, that can be used without causing solution short circuiting. This rate is a function of the minimum permeability in the heap or dump. The expression for qmax is qmax (gal/ft2/hr)[~]0.9 k (darcies). Here k is the appropriate permeability coefficient. Using this equation, qmax is found to be on the order of 1 gal/ft2/hr (4 cm/hr) for a typical heap or dump leach operation.

Jan 1, 1984

By S. Bagchi

The LaNi5-xMnx-hydrides have potential applications in cryocooling devices for non-mechanical method to compress hydrogen gas. Thermal aging behavior of LaNi5-xMnx-hydrides of compositions x=0.4 and x=1.5 has been investigated. The hydriding properties of the La1.02Ni4.6Mno.4 alloy do not change significantly after thermal aging at 453K for 260 hours. X-ray diffraction analyses of this aged alloy do not reveal the presence of any new phases but the Bragg peaks become broader. Line profile analyses show anisotropic microstrains with an average <e2>1/2 value of -5x103. Thermal aging of the other hydride, LaNi3.5Mn1.5 hydride, at 623K for 280 hours, showed significant disproportionation; the hydrogen capacity reduced significantly from an H/M value of 0.75 in the activated condition to -0.15 after aging. X-ray diffraction analyses showed disproportionated lanthanum dihydride, metallic Ni, and Mn phases. The Bragg peaks were very broad indicative of microstrains or small crystalline domains.

Jan 1, 1997