Search Documents

By Dean. R. S.

The work of the copper metallurgy section during the year was devoted to laboratory studies of sulphur recovery from smelter smoke and combination smelting of copper and manganese. Both of these subjects were new this year. Combination Smelting of Copper and Manganese According to published work, the affinity of manganese for sulphur is greater than that of iron for sulphur, so that if a suitable mixture of com-pounds of iron, copper, and manganese be smelted to form a matte and slag, manganese should concentrate in the matte, together with copper.

Jan 1, 1937

By Benjamin C. Craft, Frank Perkins

The wall-building properties of salt-water muds can be maintained at high temperatures by additions of gum karaya, gum ghatti, gelatinized starch, or commercially prepared starch. A germicide should be used to prevent fermentation. Introduction The behavior of drilling mud has received special attention from the petroleum industry within the past few years in numerous research projects dealing with such subjects as chemical treatment, gelation, and filtration characteristics. The importance and control of filtration, or water loss, is readily apparent* It affects the analysis of side-wall cores and interpretation of electric logs; it controls to a large extent the work of primary cementing, reduces the amount of expensive fishing, and permits the running of long strings of casing. It has been found that among the many factors that have an adverse effect on filtration, the presence of electrolytes, in general, and of salt, in particular, is outstanding. The effect is one of flocculation of the colloids due to neutralization of the negative charges on the clay particles. This reaction is further increased on the Gulf Coast because high temperatures reduce dispersion, to a minimum, causing increased flocculation in both fresh-water and saltwater muds. The problem of reducing water loss in salt-water muds by the addition of gums and starch at atmospheric temperature has been investigated,' and many successful field tests in West Texas indicate its solution. From the work of Byck2 it is concluded that no existing method will permit an approximate determination of the filtration rate at high temperatures from data taken at room temperatures. Filtration should be measured at the ternperature actually anticipated in the well, or at least at a number of lower temperatures and extrapolated over a small range. A laboratory study has been made of the chemicals available for the filtration characteristics of salt-water muds at high temperatures, and the use of germicides to prevent fermentation. Laboratory Investigations Procedure Since the purpose of this investigation was to compare several different gums and starches at elevated temperatures, mud from the same source was used for all the tests. Viscosity was measured in a Stormer viscosimeter at 600 r.p.m. and water loss was determined with a Baroid High-pressure and High-temperature Wall-building Tester3 at temperatures from 80' to 250°F. and at a pressure of 500 lb. per sq. in. for 30 minutes. The samples tested consisted of 150 grams of commercial Louisiana mud, 50

Jan 1, 1943

By Benjamin C. Craft, Frank Perkins

The wall-building properties of salt-water muds can be maintained at high temperatures by additions of gum karaya, gum ghatti, gelatinized starch, or commercially prepared starch. A germicide should be used to prevent fermentation. Introduction The behavior of drilling mud has received special attention from the petroleum industry within the past few years in numerous research projects dealing with such subjects as chemical treatment, gelation, and filtration characteristics. The importance and control of filtration, or water loss, is readily apparent* It affects the analysis of side-wall cores and interpretation of electric logs; it controls to a large extent the work of primary cementing, reduces the amount of expensive fishing, and permits the running of long strings of casing. It has been found that among the many factors that have an adverse effect on filtration, the presence of electrolytes, in general, and of salt, in particular, is outstanding. The effect is one of flocculation of the colloids due to neutralization of the negative charges on the clay particles. This reaction is further increased on the Gulf Coast because high temperatures reduce dispersion, to a minimum, causing increased flocculation in both fresh-water and saltwater muds. The problem of reducing water loss in salt-water muds by the addition of gums and starch at atmospheric temperature has been investigated,' and many successful field tests in West Texas indicate its solution. From the work of Byck2 it is concluded that no existing method will permit an approximate determination of the filtration rate at high temperatures from data taken at room temperatures. Filtration should be measured at the ternperature actually anticipated in the well, or at least at a number of lower temperatures and extrapolated over a small range. A laboratory study has been made of the chemicals available for the filtration characteristics of salt-water muds at high temperatures, and the use of germicides to prevent fermentation. Laboratory Investigations Procedure Since the purpose of this investigation was to compare several different gums and starches at elevated temperatures, mud from the same source was used for all the tests. Viscosity was measured in a Stormer viscosimeter at 600 r.p.m. and water loss was determined with a Baroid High-pressure and High-temperature Wall-building Tester3 at temperatures from 80' to 250°F. and at a pressure of 500 lb. per sq. in. for 30 minutes. The samples tested consisted of 150 grams of commercial Louisiana mud, 50

Jan 1, 1943

By Frederic Lahee

THE total production of crude oil in Texas during 1924 was said to be 133,613,985 bbl. as compared with 125,991,628 bbl. in 1923.1 Subtracting from these figures the yield of the Gulf Coast fields, there remains, for the other part. of Texas, a yield of 106,272,573 bbl. in 1924, as compared with 101,931,595 bbl. in 1923. This represents an increased, production of over 4,250,000 bbl. for all of Texas outside of the Gulf Coast or Salt Dome fields. Within this same region, in 1924, there were 3624 completions, of which 2352 were oil or oil and gas wells, 7 were gassers, and 1265 were dry holes. Thus, nearly 35 per cent. of the completions were dry holes. In 1923, there were 4134 completions, with 2853 oil or oil and gas wells, 2 gas wells, and 1279, or 31 per cent. of the total, dry holes. Outside of the Gulf Coast region, six major pools were discovered and developed in 1924.; two pools, previously discovered, were extended far beyond their limits at the end of 1923, and many smaller pools were opened. The major pools were the Big Lake field, in Reagan Co., the New Richland field, in Navarro Co., the Harmel, Carey, and Ragle pools, in south Archer County, and the Wortham field, in Freestone and Limestone Counties. Fields that were notably extended were the Panhandle producing area and the Luling field. Many wildcat wells have been drilled; most -of these were failures, but several opened .pools and several have had sufficiently favorable results to. lead to further drilling. The activity of the operators in searching for new production was very intense during 1924, and indications point to as feverish a campaign during the coming year. This will be stimulated by rising prices for crude oil. There are good reasons for believing that new pools will be discovered along the Mexia fault zone, in Archer, Young, Baylor, and Throckmorton Counties, in the great central region of Texas where we now have the Mitchell County and Reagan County pools, and very likely in the eastern Red River Counties including Cooke and Grayson. On the other hand, with the opening of the year, there is no new big pool in sight. An outstanding feature of the production end of the business is the increasing reliance placed on geological work and geological recommendations. Not in five or six years has there been such a demand for first-class geologists.

Jan 3, 1925

By A. J. Shaler, J. Prieto Isaza, J. Wulff

Tantalum metal has a number of unique properties which give it widespread application in modern technology and in research. In electronic apparatus involwing high temperatures in vacuo some of the refractory metals 6ecome brittle. Tantalum retains its ductility at elevated temperatures, and this property, together with its low vapor pressure and its ability to absorb gases, make it important in this field. Its chemical inertness in the presence of acids, halogens, and other corrosive media, makes it useful in chemical apparatus and in neuro and orthopedic surgical applications. As an addition to tungsten carbide in steel-cutting grades of cemented-carbide tools, the carbides of tantalum and of its sister element colum-bium have found considerable use. The present-day method1 of manufacturing tantalum is to sinter a powder compact of the metal in vacuo. Because tantalum-columbium alloys are difficult to work and since tantalum ores almost always contain columbium, the two metals must be separated chemically, the products of the separation being generally in the form of potassium tantalum fluoride and potassium columbium oxyfluoride. These salts are used in fused-salt electrolytic baths from which coarse metallic powder is deposited as a sponge at the cathode. Finer powder can be made from the coarse product or from tantalum scrap by first submitting it to an embrittling heat treatment in hydrogen and then crushing it. The fine hydrogen-containing powder may subsequently be degassed in vacuo at a high temperature. Prompted by the success of others2,3 in the magnesium reduction of titanium and zirconium halides; one of the authors undertook4 an investigation of the thermochemistry of the reaction between solid magnesium and gaseous tantalum penta-chloride, a subject which had not previously been studied. He found that the heat of formation of tantalum pentachloride is approximately 364,250 cal per mol at temperatures lower than the melting point of magnesium. A value of 83 units was found for the standard entropy at these temperatures. With these values, it was shown that magnesium and tantalum pentachloride are capable of reacting exo-thermically at temperatures less than the melting point of magnesium, and that no great violence is to be expected when these substances are heated together. The exothermic nature of the reaction indicated that the Drocess should be efficient and should not require much externally applied energy. Tantalum pentachloride is not commonly made commercially, and any process using it therefore involves the subsidiary problem of producing and handling this substance. A series of experiments was carried out in which dried chlorine saturated with carbon tetrachloride was passed over heated tanta-

Jan 1, 1949

By J. W. Walker, G. J. Heuer, E. W. Hough

An improved apparatus is described for the deterrni-nation of interfacial tension* by the pendant drop method in the pressure range from 15 to 15000 psi and the temperature range from 100º td 280°F. The chief characteristics of this apparatus are reliability and ease of operation. Temperature control was accomplished by means of an electrically heated jacket which could he completely removed while cleaning the apptrratus. The cell was designed so that the camera could he placed about I in, from the window without overheating the carnera lens. Separate "0" rings employed to seal each window and corresponding window backup plate gave very reliable window operation at 10,000 psi. An extra pistorr-cylinder combination was added so that a high compression ratio could he attained when gas was employed as one phase in the pendant drop cell. Other essential parts of the system were similar to an apparatus already described.' The interfacial tension for carbon dioxide and water varies from about 69 dynes/cm at 15 psi to about 19 dynes/cm at 1,250 psi for 100°F. For pressure.r between t,500 and 3,500 psi, the interfacial tension is between 32 and 24 dynes/cm at this temperature. The interfacial tension at 280°F varies from about 50 dynes/cm at 200 psi to about 17 dynes /cm at 10,000 psi. The maximum surface excess for carbon dioxide, assuming the surface excess of water to be zero, occurs at about 1,500 psi jor the 100°F isotherni and Itas a value of about -79 X 1014 mol/sq cm. At 160°F this maximum IS shifted to about 2,000 psi and has a value of about 10 X 1014 111ol/.sq cm. Other maxima, us well as several minima, are present at these and other temperatures. Judging from the data on the solubility of water in carbon dioxide at elevtrted pressures2,3, it appears that the principal maxinza natned are in regions of increasing solubility of the water in the carbon dioxide rich phase. INTRODUCTION AND APPARATUS A pendant drop interfacial tension apparatus which would accommodate an opaque liquid in a gas phase was constructed several ycars ago' for industrial purposes. This apparatus was used as a starting point for the present development. The objective of the present development was to enhance reliability and convenience of operation. Other articles'" have described pendant drop apparatus which could not accommodate a gaseous phase adjacent to the windows. A schematic diagram of the apparatus is shown in Fig. 1. The water used followed the path; A, intro-

By G. Titichoca

Modification of the blasting process considers that any increase in the energy consumption generates greater benefits if done in the later stages (associated with a larger decrease in energy consumption). Therefore, although the blasting cost is doubled, generating a greater proportion of fines in addition to a weaker ore (because with greater loads and appropriate distribution of explosives a greater number of internal cracks is generated), the reduction of the unit cost that occurs in the grinding stages (SAG and ball mills) generates a positive balance in the overall size reduction process. Codelco Chile, Division Andina, has developed an extensive experimental plan to evaluate the concept of blasting modification applying greater energy. This was implemented in two stages, each including a specific mine sector: La Union and Don Luis. This paper reviews the experience of implementing such blasting modifications at the La Union mine and its impact on the design concepts and the operation of the SAG mill plant

Jan 1, 2007

By R. F. Mehl, C. S. Barrett, A. G. Guy

INTRODUCTION IN the last few years this laboratory has published a series of papers on the mecha¬nism of age -hardening.14,1,6,11,20 Briefly stated it has been proposed that hardening is caused by lattice strains created by lat¬tice coherency between matrix and precipi¬tate; much experimental evidence has been advanced to support this thesis. The system Cu-Be is an attractive one to study. It is a system that exhibits marked age hardening; it ought to be subject to the type of analysis of structural changes hitherto explored and it is a prominent example of "discontinuous precipitation," which, though studied in other cases, 6,20 remains largely unexplained. This research shows that hardening in the Cu-Be system proceeds essentially as proposed earlier.14 Guinier-Preston zones have been observed to form on the {100) planes of the matrix; no transition lattice was found. Aging and overaging were ob¬served to occur most rapidly in the region of discontinuous precipitation-the grain boundary-apparently accelerated there by strain. The Constitution of the Cu-Be System The Cu-Be constitution diagram is shown in Fig I. The structure of the ? phase was determined by Misch16 as of the caesium-chloride type with a lattice con¬stant of 2.598 Å High temperature X ray photograms of 7.2 pct Be alloy made by Kossolapow and Trapesnikow13 led them to conclude that the structure of the P phase is simply disordered body-centered cubic with [ao] = 2.79 Å at 750°C. Previous Work The initial work on the age-hardening of Cu-Be alloys was that of Masing, Dahl, Holm, and Haase. Their numerous papers were published in book form in 1929, sub¬sequently translated.18 The effects of Be content, solution temperature, aging tem¬perature, and cold work on the hardness developed in these alloys were studied. An initial decrease in the electrical conduc¬tivity was observed when strips of a 2.5 pct Be alloy were aged at temperatures from 200 to 350°C; a wire of the same analysis failed to exhibit this decrease when aged at 350°C. A volume decrease of 0.6 pct oc¬curred during aging at 250°C. Microscopic investigations of quenched and aged alloys disclosed a regularly ori¬ented "striping" (ripples) on the a and on the ß grains. In the case of the ß the cause of the striping was held to be decomposition

Jan 1, 1948

By W. E. Lamont

The Federal Bureau of Mines, in cooperation with phosphate companies in the Florida land-pebble area, made a comprehensive study of the waste clays, or "phosphate slimes," produced in the mining of phosphate rock in Florida. These slimes represent a significant ecological problem and a major deterrent to effective land recovery in the phosphate-mining areas. Physical, chemical, and mineralogical studies were made of slime samples submitted by 15 of the 16 plants in Florida in an effort to identify factors that prevent successful consolidation of the slimes and subsequent recovery of the mined lands. Results of these studies indicated that the clay mineral attapulgite, a hydrated magnesium silicate, was primarily responsible for the very poor settling characteristics of the slimes, and that the quantity of attapulgite in the slimes effectively controlled the settling rate, pulp density of terminal solids, viscosity, percent solids of filter cake, and flocculant requirements.

Jan 1, 1975

By Johann Steynberg

The design and construction of a Concentrator based on initial pilot plant work is rarely perfect. Palabora's plant was no exception although the basic objective to produce copper in a safely conservative manner was certainly achieved in a profitable manner. identification of the metallurgical and mechanical deficiencies of the plant through operating experience and a better concept of the minerology of the orebody enabled the development of a more efficient process both in terms of the metallurgical performance and cost effectiveness. To maintain and improve this level of efficiency, continuous inspection and revision of the plant metallurgy and engineering standards is required. In this presentation a few of the investigations and changes are described: 1.0 Alternative methods to restrict and eliminate the detrimental effect of critical size material on the performance of an autogenous mill. 2.0 An analysis of the environmental condi¬tions in Palabora's grinding circuit and the introduction of high chrome balls as grinding media. 3.0 The role of magnetite in the beneficiation process at Palabora. 1.0 Alternative methods to restrict and eliminate the detrimental effect of critical size material on the performance of an autogenous mill.

Jan 1, 1985

By G. Graves, J. A. Walker

"Abstract - The Mount Fronsac North volcanogenic massive sulfide deposit is the most recently discovered massive sulfide body in the Bathurst Mining Camp. The deposit occurs within a sequence of intercalated fine-grained felsic tuff and sedimentary rocks (Little Falls member), at the top of the Nepisiguit Falls Formation. Aphyric to sparsely feldspar-phyric rhyolite and related volcanic rocks of the Flat Landing Brook Formation overlie the host sequence. The massive and semimassive parts of the deposit have a north-south strike length of 525 m and a dip of ~45°E; the deposit is continuous downdip for 600 m, and thickness varies from 2 to 20 m. The deposit contains an estimated geologic resource of 14 Mt of low-grade, semimassive (>60%) to locally massive sulfides, and includes a high-grade zone of 1.26 Mt grading 7.65% Zn, 2.18% Pb, 0.14% Cu, 40.3 g/t Ag, and 0.40 g/t Au. The semimassive to massive sulfide intersections occur in an envelope of quartz-sericite±chlorite schist, which is interpreted to be intensely deformed felsic tuff. This sequence has a maximum thickness of 140 m and contains significant (up to 50%) fine- to coarse-grained disseminated pyrite. The pyritic envelope has a strike length of 900 m and extends over 1000 m downdip. Massive sulfides are found throughout this alteration envelope, but more commonly occur at or near the upper contact. The significance of the discovery of this deposit is that it represents a near surface discovery of a large tonnage sulfide body in a mature mining camp, one in which the possibility of discovery of a new shallow deposit had been all but discounted. This opens the possibility for future discoveries in this part of the Bathurst Mining Camp. Sommaire - Le gîte de sulfures massifs volcanogènes du Mont Fronsac Nord est la découverte de sulfures massifs la plus récente dans le Camp Minier de Bathurst. Le gisement est situé dans une séquence de tufs felsiques à grains fins interlités de roches sédimentaires (membre de Little Falls, au sommet de la Formation de Nepisiguit Falls. La partie massive et la semimassive s’étendent du nord au sud sur 525 m et ont un pendage de ~45°E; le gisement est continu sur 600 m en angle de chute et son épaisseur varie de 2 à 20 m. Le gisement contient une ressource géologique évaluée à 14 Mt de sulfures semimassifs (>60%) localement massifs à basse teneur, incluant une zone à haute teneur de 1.26 Mt titrant 7.65% Zn, 2.18% Pb, 0.14% Cu, 40.3 g/t Ag, et 0.40 g/t Au. Les intersections de sulfures semimassifs à massifs se situent dans une enveloppe de schiste à quartz-sericite ± chlorite interprétée comme un tuf felsique intensément déformé. Cette séquence contient une quantité importante (jusqu’à 50%) de pyrite disséminée dont le grain varie de fin à grossier et son épaisseur maximale est de 140 m. L’enveloppe pyriteuse s’étend latéralement sur 900 m et a été tracée jusqu’à 1000 m en angle de chute. Des sulfures massifs sont trouvés partout à l’intérieur de cette enveloppe d’altération, mais ils sont plus fréquents près du contact supérieur. L’importance de cette découverte tient à ce qu’elle est un exemple d’un gisement à fort tonnage nouvellement découvert à une faible profondeur dans un camp minier mature, i.e., un camp ou l’on ne croyait plus qu’il était possible de trouver un gisement près de la surface. Ceci ouvre la porte à la possibilité d’autres découvertes dans cette partie du Camp Minier de Bathurst."

Jan 1, 2006

By John Redstone, André R. Laplante

"Le rebroyage des concentrés d'hématite en usine (Sidbec-Normines, Port-Cartier) et en laboratoire a été modélisé selon le modèle de Reid (1965).L'effet du pourcentage solide sur la cinétique de broyage a été étudié en usine. La fonction de sélection corrigée (pour tenir compte de l'effet du pourcentage solide sur le temps de rétention) augmente lorsque le pourcentage solide augmente de 80 à 84 pourcent. Cette amélioration est contrebalancée par une augmentation de la quantité de pulpe court-circuitée, à des pourcentages solides supérieurs a 81%. La densité optimum de broyage se situe à 84 pourcent.Comme alternative au mode d'opération actuel, l'assemblage des broyeurs en série plutôt qu'en parallèle a également été simulée. Le moins 44 µm passe alors de 68.1 à 72.5 pourcent, ce qui correspond à une capacité supplémentaire de 32 tonnes à l'heure par broyeur. Ces résultats doivent toutefois être interprétés avec prudence, car la cinétique de broyage n'est généralement pas linéaire lorsque le taux d'alimentation est plus que doublé.IntroductionL'usine de bouletage de Sidbec-Normines Inc. a été décrite par Morimoto (1977), Lévesque et al. (1979) et Pabst (1979). La section de broyage des concentrés contient six broyeurs à boulets en parallèle et en circuit ouvert, d'un diamètre de 5. 18 mètres et de 10.36 mètres de longueur. Ils contiennent chacun environ 350 tonnes de boulets d'acier forgé de 3.8 cm de diamètre. Le concentré est broyé de 10 pourcent moins 150 µm (100 mailles) à 65-68 pourcent moins 44 µm (325 mailles), à un pourcentage solide de 78 à 80 pourcent. Cette fragmentation poussée exige une consommation d'énergie de 32 kWh/tonne. Cette énergie est surtout libérée sous forme de chaleur, la pulpe étant déchargée a une température de 68-72° C. II en résulte un milieu de broyage corrosif, et une consommation de boulets élevée, de 3.4 à 4.0 kg / tonne broyée."

Jan 1, 1983

By J F. Seale

The design of the settling pond for the Malvern Hills opencast coal project was based on a primary requirement to control runoff and sediment generated from the immediate 6 ha mine catchment, which included two seepages from old underground workings. The pond has been particularly effective in controlling turbidity in the outflow water, with the consent limit of 50 NTU being met on all but one occasion and normal levels of discharge less than 10 NTU. Water quality testing carried out at the time of consenting indicated that there were no acid-generation issues with the proposed mine site in dominant mudstone strata of the Broken River Formation, and that water from the old mine workings was near-neutral in terms of pH and well-buffered. However, it became apparent over the very dry summer of 2003 - 2004 that slaking of the exposed mudrocks in the mine batters was resulting in significant acidity generation, and outflow pH levels were well below the consent limit of 6.5 during and following periods of rainfall. Although these acidity problems have been remediated in the short-term by the use of lime products, it is clear that a programme of lithotype characterisation for AMD should have been undertaken and this has now been implemented. Design of long-term acid drainage control measures is being carried out, and will probably be based around the use of hydrated lime for pH control with enhancement of natural wetlands.

Jan 1, 2004

By Lutz Markworth, Wolfram Jaspers, Johannes Kottmann

PNEUFLOT® technology has been applied for the past 20 years in coal, ore and other minerals processing plants. During the last two years this technology has achieved a breakthrough with some 42 units being sold signifying a rising trend. »Humboldt Wedag Coal & Minerals Technology« has performed extensive research and development work over the last five years. The results of which were used to design a new fourth generation aerator. Humboldt Wedag, through its association with EKOF, can offer a holistic solution encompassing both flotation equipment and reagents. It is the only company in the world able to offer such a package. The association with EKOF strengthens the Humboldt Wedag product offering, especially as the company in-troduced pneumatic flotation cells to the South African market in the form of the PNEUFLOT®. Before starting pilot scale test work, a mineralogical analysis has to be carried out to determine the mineral com-position as well as the liberation grade. HW-CMT works together with independent institutes. Different reagent regimes can be tested in laboratory scale. Pilot machines, each packed in a 20? container, are available to carry out extensive test work at customers? processing plants. A group of engineers from HW-CMT is involved in the pilot test work. The flexible pilot machines are designed to cater for coal, ores and other minerals. The small feed rates of 7 ? 12 m³/h only means the pilot machines do not disturb the operation of process plants. Batch tests have to be carried out to determine the numbers of PNEU-FLOT® stages. New applications in iron ore, copper ore, platinum group minerals, rock phosphate and potash were suc-cessfully tested in the last three years. In applications where the feed material is very fine, PNEUFLOT® technology is able to achieve high recoveries with particle sizes where conventional technology failed.

Jan 1, 2007

By Oswaldo Carhuancho

El presente trabajo señala la filosofía de trabajo en equipo desarrollada en la mina Pierina, Lima. La política de trabajo se sustenta en el pensamiento de Barrick, donde las prácticas administrativas basadas en la seguridad, salud ocupacional y el medio ambiente repercuten en el beneficio de sus empleados, accionistas y las comunidades en las que opera. Por ello, la primera preocupación de la empresa debe ser el trabajador y no las máquinas, así como la labor de los jefes no se limita a una actitud paternalista, sino a una democrática, de forma que el empleado asume sus responsablidades con seguridad y eficiencia. Como consecuencia de ello, se redujeron la cantidad de hombres-accidentess, se elevó el costo de producción y se redujo, la cantidad de personas en la supervisión de operaciones mina.

Sep 13, 2001

By J. Torma-Krajewski, C. Hipes

Many mining companies apply ergonomic principles, but it is done either informally and/or reactively. Examples of an informal approach include replacing worn equipment, such as seats, with models that have ergonomic features, or modifying tasks to eliminate safety hazards that will also reduce risk factor exposures that may result in musculoskeletal disorders (MSDs). A reactive approach is followed when modifying a task/equipment after an MSD occurs. Neither one of these approaches involves a systematic method of proactively applying ergonomic principles to actually prevent injuries or illnesses. This paper will discuss how Vulcan Materials Company applied ergonomic principles and the interventions implemented to reduce risk factor exposures.

Jan 1, 2007

By F. W. McQuiston

INTRODUCTION IDARADO Mining Company's mill and surface plant are at the portal of the Treasury tunnel at elevation 10,625 ft, 12 miles south of Ouray, Colo. In 1943 and 1944 this tunnel was extended in a westerly direction to tap the Black Bear vein, and, together with the recently completed 1100-ft inclined Treasury raise, provides access to the Black Bear mine. In 1945 a 250-ton mill was placed in operation to process development ores containing much needed copper, lead and zinc for war requirements, and to serve as a pilot testing unit for larger scale milling operations. In the years 1902 to 1927 some 329,000 tons of ore were produced from mine workings on the Black Bear vein that extended downward from elevation 12,325 ft at the Black Bear tunnel portal to elevation 11,618 ft, the lowest level of the mine. The ores were taken to the Cascade and Smuggler-Union mills near Telluride over two aerial tramways. Gold bullion, a copper-lead concentrate, and a zinc concentrate were produced. ORES The Black Bear is a compound fissure vein that has undergone several stages of mineralization. The first important stage is represented by complex ores of copper, lead and zinc in a quartz gangue. Precious metal content in this stage is low. The galena is argentiferous and varying amounts of tetrahedrite, freibergite and bornite tend to increase the normal copper content represented in chalcopyrite. The zinc occurs as a true sphalerite with little or no iron. Later re-openings of the fissure took place more or less co-extensively with the successive introduction of (1) abundant quartz gangue containing minor amounts of chalcopyrite, galena and sphalerite; (2) free gold in a fluoritic quartz gangue; and (3) barren, low-grade quartz with minor amounts of pyrite as the only important sulphide. The sulphides show practically no oxidation and little mineralogic intergrowth. Because of the common overlapping of these successive stages of mineralization within a given mining area, considerable dilution of the base-metal content takes place, thus lowering the average mill-head grade. PLANT PRACTICE Metallurgical testing was started shortly after the Black Bear vein was encountered on Treasury tunnel level in 1944. Laboratory tests showed good flotability of the minerals in the ore and indicated an economic separation could be made of the copper, lead and zinc minerals into their respective concentrates. The success of the separation is close reagent control to maintain a balance between promotion and depression of the sulphides. To maintain this balance reagent consumption for the three metal separation is considerably higher than in ordinary lead-zinc flotation.

Jan 1, 1947

By Richard McCaffery

THERE has been some discussion among blast-furnace operators regarding the relative merits of tuyeres of the converging type and tuyeres designed in an attempt to produce a diverging jet of air. An article1 on Progress in German Blast Furnace Practice indicates the interest in this subject abroad. This article illustrates a diverging type of tuyere which is shown here in Fig. 1A. The design appears to be rather poor as regards known properties of air flow. The adoption of this. tuyere, the article states, resulted in a decrease of blast pressure of about 4 lb. per sq. in. and an increase of the output of the furnace. If the improvements mentioned are due entirely to the change in tuyere design, the subject of tuyere design seemed worthy of investigation and this paper is a report of such work. Because of the gain in efficiency brought about by the use of a diverging tuyere in the German plant, it was thought desirable to investigate the shape of the air streams issuing from various-types of tuyeres to ascertain whether the gain was due to the tuyere itself or to the distribution of the air in the furnace. Since it is difficult to do experimental work on a full-sized furnace, or even on full-sized tuyeres, and because of the equipment available for the work, it was decided to carry out the work on scale models of tuyeres. Therefore, in this work, single tuyeres were used and the blast discharged into the atmosphere. The shape of the air stream was determined by means of a Pitot tube suitably supported in the air stream at various positions. The air was. furnished by a Roots blower driven by a 10-hp. direct-current motor having field control, and capable of discharging 250 cu. ft. per min. with a pressure on the discharge of 4 in. of mercury. A modern blast furnace with 21-ft. hearth requires about 50,000 cu. ft. per min. of free air at from 16 to 23 lb. per sq. in. pressure, depending upon the type of burden. This pressure is the total pressure required to force the air through the burden and through the tuyeres. Upon computation the pressure drop through the tuyeres is about 1 to 2 lb. per sq. in. By making the tuyeres to a one-fifth scale, and by using a pressure of 1.5 in. of mercury, the shape of the air streams should be

Jan 1, 1931

By Walter L. Maxson, Fred C. Bond

SINCE the last publication of tabulated results of grindability tests by the authors1 the total number of ball-mill tests made has more than doubled, and rod-mill tests have become increasingly important. Nearly all of the standard closed-circuit ball-mill and rod-mill tests made to date are included in the present tabulation, together with additional information not previously published. STANDARD BALL-MILL GRINDABILITY TESTS The method of conducting these closed-circuit tests has not been altered. A sample of the ore or other material is stage-crushed in rolls set at 1/16-in. opening with a 6-mesh screen until all of it has passed the screen. The combined minus 6-mesh screen undersize is mixed, sampled and screen-analyzed, and its apparent specific gravity is determined by packing and shaking in a standard container, and weighing. The apparent specific gravity ordinarily is about 60 per cent of the true specific gravity. The unit volume present in the mill in all tests is 700 c.c. of the packed minus 6-mesh roll product, and the number of grams occupying 700 c.c. is the unit test weight. This weight is placed in the mill dry, ground for the number of revolutions estimated to be necessary, discharged, and screened mechanically in three testing sieves of the mesh size at which the test is to be conducted. The oversize, or circulating load, is weighed, sufficient fresh minus 6-mesh feed is added to bring the total weight up to that of 700 c.c., and the charge is returned to the mill for a second grinding period. All standard ball-mill tests are conducted at 250 per cent circulating load, and the number of revolutions in the mill necessary to obtain this circulating load at any grinding period is estimated from the results of the previous period. The number of net grams of screen undersize produced per revolution of the mill approaches its final equilibrium value after several grinding periods, and this is recorded as the grindability, or relative ease of grinding, of the sample. A cylindrical ball mill, 12 by 12 in. inside, with a smooth lining and rounded corners, is used with a revolution counter. Under standard grinding conditions it runs at 70 r.p.m., and contains a charge of 285 iron balls weighing 20,125 grams, ranging from I ½ to ¾ in. in diameter. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the capacity to be expected from a given mill is calculated by comparing the

Jan 1, 1943

By J. E. Chilton, T. Mal

Methane monitoring at the mine face is essential to assure a safe work environment in underground coal mines. Machine-mounted methane monitors must be used to continuously monitor methane levels during mining. Monitors used on mining machines must be approved by MSHA and properly maintained to provide protection for workers (30 CFR 75.342). To provide protection the instrument must give accurate readings of current methane levels. Accuracy is maintained by calibrating the instrument with a standard gas at least once every 31 days. Instrument “response time” determines how quickly measurements will change to reflect current concentrations. At present there are no criteria for measuring the response time for a ma-chine-mounted methane monitor while underground. This study examined a procedure for measuring the response time of a machine-mounted methane monitor. Response times were measured using methanometers obtained from three different manufacturers. The effects of the measurement technique and methanometer sensor head design on response time measurements are investigated. Techniques for reducing variation in response time measurements are discussed.