Search Documents

By Shaik Jeelani, Mahesh Hosur, Esperidiana A. B. Moura, Rejane D. Campos, Emilia S. M. Seo, Kerry Kirwan, Francisco R. V. Díaz, Maria Sotenko

The use of natural fibers with polymeric resins has spread rapidly. In order to improve the mechanical properties of material, in this work, two variables were used: mercerization and electron beam irradiation. This paper describes the preparation and characterization of biocomposites that were prepared in two different routes using green high density polyethylene (HDPE) and Brazil nut pod fiber (BNPF): the first was to irradiate the composite with 150 kGy and the second was to irradiate the matrix with 15 kGy followed by composite preparation. In both cases mercerized and non-mercerized fibers were used. The irradiation process was carried out using a 1.5 MeV electron beam accelerator, at room temperature and in the presence of air. The material was characterized to evaluate the effect of treatment on mechanical properties of material.

Jan 1, 2015

By R. M. Carland, F. F. Aplan

The ion-exchange capabilities of natural zeolites from the western United States, representing the species chabazite, clinoptilolite, erionite and mordenite, have been studied because of their potential use in environmental remediation and in hydrometallurgical processes. These raw zeolite samples were found to contain Na+, K+, Ca+2 and Mg+2 as exchangeable cations, and all of these, with the exception of Na+, were found to seriously interfere with the exchange of Cu+2 from solution. Placing these zeolites in the Na+ form was found to increase their cation-exchange capacity, often massively. In addition, the elution of Cu+2 from the Na+ pre-exchanged zeolite is greatly facilitated when the deleterious K+, Ca+2 and Mg+2 have been largely expelled. The relative influence of these deleterious ions on the uptake and elution of Cu+2 was determined.

Jan 1, 1996

By D. A. Stanley

The Bureau of Mines has developed an equation which describes the dewatering of clay slurries with polyethylene oxide. This dewatering equation is An _ kC + b where n, k. and b are empirical constants and C is the concentration of polymer solution used for dewatering. The minimum amount of polymer required for dewatering. A is determined by titration of the clay slurry with a polymer solution. In this report, the dewatering equation is applied to data obtained for a polyacrylamide dewatering sequence. Fundamental similarities between the dewatering properties of clays and the viscosity of polymer solutions were observed. These similarities were explained by correlating an equation describing polymer configuration in solution with the dewatering equation. This correlation showed that amount of polymer required for dewatering and polymer solution viscosity are both consequences of the frictional interaction of entangled polymer coils.

Jan 1, 1989

By S. K. Nandy, K. F. Unrug

The behavior of the immediate shaly roof within a drift mine in eastern Kentucky, operating in the Coalburg seam, was monitored with roof bolt dynamometers. The dynamometers used were capable of providing readings up to a maximum load of 66.72 kN (15,000 lbs), + 0.022 kN (5 lbs). To observe the influence of moisture on the rate and extent of roof deterioration, 57dynamometers were installed on roof bolts anchored in intake and neutral airways. Monitoring was conducted during the period January 1985 through January 1986, in order to cover a full cycle of dry and wet mine conditions associated with seasonal changes. Analysis of the data showed a trend of roof deterioration induced by condensation and eventual penetration of moisture within the immediate roof bedding planes, leading to rapid disintegration of the mine roof.

Jan 1, 1987

The ongoing need for improved fuel economy, longer engine life, reduced emissions and greater power output has driven the need for lower charge air temperatures. Cuamins will introduce a split loop, single water pump approach to low temperature aftercooling (LTA) in 1987 with the introduction of its 1492 kW (2000 BP) 16 cylinder K Series engine. The LTA system selection process considered performance, durability, fuel economy, and total engine installed cost. The split loop system selected takes full advantage of the engine cooling characteristics to provide optimum charge air temperatures at all speeds, loads and ambient temperatures. Computer simulations and engine tests were used to determine performance for each charge air cooling alternative. The split loop system chosen offers many advantages compared to the other alternative systems studied which included air-to-air and dual loop (two radiator, two water pump) systems.

Jan 1, 1986

By Kenneth N. Han, Xinghui Meng, A. J. Monhemius, G. W. Warren, E. Peters

The leaching of gold in ammoniacal solutions containing various oxidants in an autoclave has been investigated. Also studied are thermodynamic and kinetic aspects of the ammonia leaching of gold and silver. The variables studied included stirring speed, temperature, concentration of ammonia, ammonium, and various anions. Arrhenius activation energy values were found to be between 47.1 kJ/mol and 86.2 kJ/mol depending upon the kinds of oxidants used. An electrochemical reaction controlling mechanism has been proposed for the dissolution reaction. The leaching behavior of gold and silver from various ores in ammoniacal solutions containing various oxidants has also been investigated. The samples tested included sulfidic as well as carbonaceous refractory ores. The recoveries of gold and silver from these refractory ores were better than 96% within 2-3 hours of leaching time.

Jan 1, 1993

By N. Zouridakis

Radon is an established lung carcinogen and remains the most important environmental radiation exposure. It was estimated that inhalation of radon and its short-lived decay products accounts on average for about one half of the effective dose equivalent from all natural sources of radiation. Radon contained in household water can transferred into room air as a result of agitation or heating. An indoor air concentration of 400 Bq/m3 is obtained if the radon concentration in household water is 4 kBq/L. A typical concentration of radon in ground water is about 1000 times lower than this concentration but sometime elevated concentrations of some kBq/L in ground water are reported. In this work a Liquid Scintillation counting system is used to obtain fast and accurate measurements of radon (222Rn) in water samples from Argolida, Greece.

Jan 1, 2007

Acupan is considered to be an intrusive centre as several igneous phases have been emplaced in the vicinity of the mine over the past 8 Ma. They include the Lucbuban gabbro, Virac granodiorite, Ampucao dacite porphyry (ADP), Hartwell plug, Itogon plug and the multi-phase Balatoc diatreme. These intrusives have high-K calc-alkaline affinities and are grouped together as the Virac Complex.Porphyry-style mineralisation formed during the final crystallization of the ADP in the late Pliocene, with the deposition of two vein stages from high-temperature hypersaline magmatic-hydrothermal fluids. K-silicate alteration halos surround the first stage of veinlets (stage I); they are surrounded in turn by a propylitic assemblage. White sericite and/or intense propylitic halos envelop the second stage of veinlets (stage II) and grade into a weak nrnnvlitir accPmht o

Jan 1, 1990

By Ginn Huh

The blasting work to construct a subway in Seoul, Korea have often caused increased neighbor’s complaints because of ground vibration. In order to prevent the damage to the structure, it was necessary to predict the level of blasting induced vibration and to determine the maximum charge weight per delay within an allowable vibration level. The effect of blasting pattern, rock strength and different explosives on the blast-induced ground vibration was studied to determine the maximum charge weight per delay within a given vibration level. The blasting vibration was measured from 10 sites along the subway line in Seoul and an empirical particle velocity equation from over 100 test data was obtained, V=K(D/W1’3 )-” , where the values for n and K are estimated to be 1.7 to 1 S and 48 to 138 respectively.

Jan 1, 2000

By Robinson J

A stibnite flotation concentrate from Costerfield in Victoria was found to contain 63.3 g/t An while its sizing distribution indicated that 81.6 per cent of the material was less than 38 ¦m. A 24 hour cyanidation test by a standard bottle roll method recovered 15 per cent of this gold. Pressure cyanidation under conditions of ambient temperature, 40 per cent pulp density, an oxygen pressure of 1000 - 2000 kPa and an initial NaCN concentration of 15 kg/t, resulted in a recovery of 65 pe cent of the gold after only two hours of leaching. Aqueous pressure preoxidation of the concentrate followed by the standard bottle roll cyanidation realised gold recoveries as high as 96 per cent. Conditions of 220¦C, an oxygen pressure of 1000 - 2000 kPa, 16.7

Jan 1, 1991

By M Hino, Y Sasaki

Sustainable handling of municipal waste and sewage sludge has an important goal to recycle resources without supply of harmful substances to humans or the environment. The gasification mechanism of phosphorus from municipal waste and sewage sludge during the incineration process has been investigated to develop a phosphorus recovery system. Quadrupole mass spectrometer coupled to an electric furnace is applied to study the vaporisation behaviour of phosphorous gas phases from municipal solid waste (MSW) incinerator ash of sludge during solid-state reduction by carbon. Measurements are carried out in vacuum conditions of 2 x 10-6 Torrs and furnace temperature range 573 - 1773 K, at a heating rate of 7.22 K/minute. It has been found that most of the phosphorus is vaporised as PO2, P2 and P4, in agreement with thermodynamic estimation despite a shift in the temperature regimes.

Jan 1, 2006

By Vance G. Leak

A technique for recovering copper and steel from metallic scrap has been developed by the Bureau of Mines based on preferential melting in molten salt baths at 1,150° to 1,250° C, The molten salt, preferably barium chloride or calcium chloride, both minimizes oxidation of the metals and promotes heat transfer. Cleanest separations (0.01 percent copper remaining in iron) have been achieved by pretreatment (dipping or spraying) with sodium sulphate or sodium silicate, which alters and coats the surface of the iron to inhibit the alloying or brazing with copper. An economic evaluation of the process was carried out on six combinations of sweating media and inhibiting reagents. On the basis of the postulated model, a cost of about $0.20 per pound of copper recovered has been determined for the sweating treatment operation.

Jan 1, 1973

By G. E. Pellissier, P. H. Salmon Cox, B. G. Reisdorf

Banding that occurred in plates rolled from the early production heats of 18Ni(250) maraging steel is described and related to the segvegation of certain alloying elements (nickel, molybdenum, titanium), the extent of which was quantitatively evaluated by means of electron-microprobe analysis. The effect of banding on mechanical properties is discussed, with particular reference to observed directional differences in plane-strain fracture toughness of plates. It is shown that banding originates as interdendritic segvegation during ingot solidification and persists in some degree through normal soaking and hot reduction to plate. The results of the study showed that heating sections of small laboratory-cast ingots at 2200°F for 4 hr was sufficient to markedly reduce microsegregation and to considerably improve mechanical properties. Hot rolling of 7-in.-thick ingot sections to 1/2-in.-thick plate effected a similar reduction of microsegregation, but resulted in even greater increases in ductility and toughness than that obtained by homogenization treatment alone. DURING the past few years, considerable attention has been directed towards the low-carbon, high-alloy maraging steels and in particular towards the 18Ni-8Co-5Mo-0.4Ti alloy. The steels of this group, having an excellent combination of high strength and toughness, have a number of advantages over their more conventional medium-carbon low-alloy, quenched-and-tempered counterparts. In the annealed condition, the maraging steels are in the form of a ductile marten-site; aging at a relatively low temperature, typically 900°F for 3 hr, increases greatly the strength through the precipitation of intermetallic compounds. One problem in the early production heats of maraging steel was that the finished plate frequently displayed a banded structure. Previous work on other steels1-' had established that banding in wrought products is either a direct or an indirect consequence of chemical segregation, which occurs during solidification and persists to some extent through normal thermal and mechanical treatments. For example, Smith and others: in a study of low-alloy steel, were able to correlate the severity of banding in the wrought product with the degree of interdendritic segregation of nickel and chromium in the as-cast ingot. The effect of banding on the mechanical properties of steels is usually considered to be detrimental, although there is only limited evidence to suggest that a marked improvement in properties can be obtained with less heterogeneous structures. Comparison of the longitudinal and transverse tensile properties of banded and of homogenized 4340 steel showed that only the transverse ductility was improved by homogenization, but even then the improvement was not commercially significant.' Conversely, homogenization of through-the-thickness tension specimens of quenched-and-tempered steel plate, containing 1.47 pct Mn, increased the strength by as much as 10 pct and the tensile ductility by at least a factor of twos5 This improvement was related to the elimination of manganese-rich bands, which also are one of the factors responsible for cold cracking in the heat-affected zone of metal-arc welds.7 In the present study the nature and severity of banding in early commercial 18Ni(250) maraging steel plate and in laboratory-melted 18Ni(250) maraging steel plate was determined. The effects of banding on plane-strain fracture toughness and the effects of thermal homogenization treatments on the strength, tensile ductility, and toughness of 18Ni(250) maraging-steel as-cast ingots and rolled plate were evaluated. In addition, the effects of hot deformation by rolling on the mechanical properties of ingots were determined. 1) STUDIES OF BANDING IN EARLY PRODUCTION PLATE The chemical composition of the steel (A) used in this part of the investigation is shown in Table I. Banding was not clearly evident in either as-rolled or annealed* plate, but annealed and agedc** plate had a banded structure. The typical banded condition, Fig. 1, consists of layers of unetched austenite (white) and dark-etching martensite in a light-etching martensitic matrix. X-ray diffraction measurements showed that this steel contained more than 6 pct austenite. An electron-probe X-ray microanalyzer (using a focused beam of electrons) was used to determine the composition of the bands and of the material between the bands with respect to the main alloying elements— nickel, molybdenum, titanium, and cobalt. The recorded X-ray intensities were converted to concentration values with the use of a standard of similar composition. To facilitate probe positioning, all analyses were conducted on specimens that had been given a light etch. The influence of this etching on the analytical results was negligible; analyses made on the identical area before and after etching yielded essentially the same concentration values. The results of the electron-microprobe analyses at selected points revealed that the layers of austenite and adjacent dark-etching martensite contained greater amounts of nickel, molybdenum, and titanium than did the surrounding matrix, Table 11. The austenite layers

Jan 1, 1968

By Do-Hyeong Kim, Jong-Jin Pak, Jung-Mock Jang, Min-Kyu Paek

"Thermodynamic relations among Mn, Al and N in liquid iron were studied by measuring the effect of Mn on the solubility product of AlN in liquid Fe-Mn-Al-N alloys in the temperature range from 1773 to 1873 K. The critical Al and N contents for AlN formation were determined by the metal-nitride-gas equilibration technique over wide ranges of melt composition and temperature. The effects of Mn on N solubility in Fe-Mn and Fe-Mn-Al melts containing Mn up to 26 mass% were separately determined in the same temperature range. The experimental results were thermodynamically analyzed using the Wagner's formalism to estimate the critical Al and N contents for the onset of A1N formation. The validity was checked by the observation of inclusion evolution in Fe-20%Mn-1.5%Al-0.6%C-0.3%Si-0.012%N melt during cooling and solidification.IntroductionRecently, high manganese steels such as Twinning Induced Plasticity (TWIP) steels have been developed as next generation steels because of their high formability as well as excellent strength and ductility.[1•2l In these steel grades, a large amount of Mn (15-20 mass%) and Al (1-2 mass%) are added to liquid steels, and such high Mn and Al concentration bring the great challenges to the steelmaking and casting processes. Mn significantly increases the N solubility in liquid iron and the AlN inclusions can be easily formed at such high Al concentrations due to high affinity of Al and Mn with N in liquid steels. Although the AlN inclusion is known to be a dominating and considered as a detrimental phase for the hot ductility of steels,l3l thermodynamics of AlN formation in high Mn-Al alloyed liquid steels was not well known.Moreover, the melting point of these steels decreases down to near 1623 K as increasing Mn content up to 20 mass%. However, most of thermodynamic data has been measured at the steelmaking temperature around 1873 K. Even at steelmaking temperature, there are huge scatters in thermodynamic interactions of Mn and Al on N in liquid iron. The nitrogen solubility in Fe-Mn alloy melts has been measured using the Sieverts' method[4l and the samplinij method[5-7J in the temperature range of 1813 to 1973 K. In the authors' recent study,[8•9 the N solubility in Fe-Al alloy melts was measured using the sampling method in the temperature range of 1823 to 1973 K. However, the simultaneous effect of Mn and Al at high concentrations on Nin liquid Fe-Mn-Al-N alloys is still not known. Also, there remains uncertainty about the temperature dependence of the interaction parameter of Mn on N in liquid Fe-Mn alloys. Therefore, it is worthwhile to check the temperature dependence of this parameter at a low temperature near the melting point of Fe-Mn alloys. There have been few studies on the characterization of non-metallic"

Jan 1, 2014

By Naj Aziz, Peter Craig

"Double shearing tests were carried out on the 28 mm (1 in) hollow strand Jennmar TG cable bolt to gain a better understanding of the shearing behavior of the cable. The first test was limited to a 50 mm (2 in) travel on the testing machine and produced a shear load of 900 kN (92 t) at the maximum 50 mm (2 in) displacement. The axial load generated on the cable bolt was 238 kN (24.3 t). In the second test, the machine travel was increased to 75 mm (3 in), and first strand failure of the cable, due to shear loading, occurred at 1,354 kN (138 t) vertical load at a vertical displacement of 59 mm (2.3 in). The cable axial load was in the order of 385 kN (39.3 t). Analysis of the failure mode and loads achieved showed that the cable strands bent and the concrete crushed along the shear plane; the shear loading across the concrete and grouted cable then reached the tensile strength of the steel wires.INTRODUCTIONCable bolts were introduced to the mining industry around 1970, initially to surface mining and underground metalliferous mining and then to coal mining in the early 1980s, mainly for roadway reinforcement as a secondary means of support. Cable bolts have since been used as both primary and secondary supports. As primary support, Fuller et al. (1994) described the application of cable bolts, known as FLEXIBOLT, for strata reinforcement in both Angus Place and Ellalong Collieries, in New South Wales (NSW), Australia. As secondary support, cable bolts have also been used as cable trusses, which act to support the immediate roof in a sling-like manner (Fabjanczyk and Tarrant, 1988; Fuller, et al., 1991; O'Grady and Fuller, 1992), and for reinforcement at higher stratification and beyond the rebar bolt length, mainly for anchoring lower strata layers immediately above the coal seam to the higher, competent bedding formation above. Initially cable bolt anchorage was by cementatious grouting and, since the 1990s, by chemical resin. The dominant type of cable bolts used for secondary support in Australian underground coal mines are 588 kN (60 t) capacity cables which are point anchored, pre-tensioned and post-grouted. Point anchored refers to a cable resin anchor. The cables are tensioned on the resin anchor; then the same cable is grouted by cementatious grout pumped to ·fin the annular gap around the cable from the collar of the hole to the resin anchor. Bulbs are located within the resin anchor section for mixing of the resin chemical components and efficient anchorage. The installation of these typically 8 m long cable bolts involves a lot of manual handling of the cables, lifting of heavy hydraulic tensioners, and exposure to resin grouts. Table 1 shows the specification of various cable bolts currently marketed and installed in Australian underground coal mines."

Jan 1, 2010

By A. E. Sobolev

The kinetics of hydrochemical oxidation of antimonite in solutions of nitric acid was studied using the rotating disk method and the factor experiment design. The dependences of the antimonite?s oxidation rate on concentration of nitric acid solutions, temperature, disk rotation frequency, and duration of interaction were determined. The adequate kinetic models allowing calculating the specific oxidation rate at any combination of the values of the influencing factors were obtained. The oxidation process is found to proceed in a mixed mode, close to chemically controlled. Gradually, as the sediments of elemental sulphur and Sb2O5 accumulate on the disk surface, the process becomes controlled by internal diffusion. The observed high (more than second) order of the oxidation rate with respect to the concentration of nitric acid was explained by the autocatalytic action of the acid reduction products. The apparent activation energy depends on the stage of interaction. At the initial stage (in a mixed mode of the process proceeding), it depends on nitric acid concentration and varies from 31.5 kJ?mol?1 (in 2 M HNO3) to 36.1 kJ?mol?1 (in 10 M HNO3). This trend indicates the weakening of diffusion limitations with a nitric acid concentration increase. When the process is controlled by internal diffusion, the apparent activation energy was found to be 14.5 kJ?mol?1. The obtained kinetic characteristics enlarge the database on hydrochemical oxidation kinetics of sulphides and can be used for the elaboration of the recommendations for the effective comprehensive exploitation of antimony-bearing ores and concentrates.

Jan 1, 2014

By X Zhang, Y Zhu, P E. Ngoepe, P P. Mkhonto, W Xiong, L Han, L Lu

The triazine molecules have not been given much attention and they are potential collectors that may positively impact the mineral processing industry. The adsorption of triazine as collectors such as sodium 2,6-dithio-4-butylamino-1,3,5-triazine (SDTBAT) on pyrite form a basis in design of flotation collectors that may be applicable in a wide range of sulfide minerals. The SDTBAT collector was compared with the sodium normal butyl xanthate (SNBX) and sodium normal butyl dithiocarbamate (SNBDTC). All collectors were adsorbed in their neutral form containing sodium on the pyrite (100) surface. The computational calculations found that the adsorption energies followed the order: SDTBAT (-300.35 kJ/mol) > SNBX (-186.10 kJ/mol) > SNBDTC (-163.78 kJ/mol). It was observed that the SNBX and SNBDTC adsorbed through the S atoms, while the SDTBAT adsorbed through the S atoms and N atoms onto Fe atoms. It is clear that the SDTBAT had a strong binding energy which is attributed to the presence of the triazine group that is electron depositing to the active S atoms compared to the SNBX which possessed the oxygen that is electron withdrawing. Moreover, the SDTBAT collector was found to bind stronger than the xanthate. This was complimented by microflotation tests that showed fast floating and higher recoveries of pyrite when using the SDTBAT collector than the xanthate and DTC. This clearly demonstrated that the SDTBAT is a potential collector to replace the xanthate collector due to its high selectivity and flotation power.

Aug 24, 2022

By H. Ipek

In this study the effects of interstitial ratios on k-feldspar samples were investigated. The k-feldspar samples were taken from Egypt using dry batch grinding conditions and a kinetic model. Three different mono size fractions (-3350+2360, -850+600 and -300+212 µm) were ground separately for 0.5, 1, 4, and 8 minutes and at four different interstitial ratios (125%, 100%, 75% and 50%) using a Bond mill with a mixture of five ball sizes. The mill used was at a size of 30.5 cm diameters, with 30.5 cm length, providing a total mill volume of 22272 cm3. The mill has a total mass consisting of 22648 g. steel ball mixtures of 38.10, 31.75, 25.40, 19.05 and 12.70mm diameters, occupying 22% of mill volume. The mill rotates at a speed of 70 rpm. The weights of the feed charges were 3000, 2000, 1000, and 500 g for 125%, 100%, 75% and 50% filling of the interstices of the balls respectively. The specific rate of breakage (Si) was determined from the top size fractions at different grinding times that were mentioned above and the model parameters were compared for the four different powder filling ratios (U). In many investigations, it has been found that an interstitial filling ratio of U = 0.6-1.1 is a good powder ball loading ratio to give an efficient breakage in a ball mill. In this study, it was found that U=1.25 is a good ratio for K-Feldspar.

Jan 1, 2006

By G. F. Tagg

In an earlier paper1, the author described a method of interpreting earth-resistivity curves, based on the theoretical investigation of a single horizontal underlying stratum. If the four-electrode system of Wenner is employed, the resistivity in a homogeneous soil is given by the formula p = 2paR [1] where a is the electrode separation and R is the resistance of the earth between the two inner electrodes. If the earth is not perfectly homo¬geneous, the application of this formula gives an apparent specific resistance varying with the electrode separation. In the special case of the single horizontal underlying stratum, there is a surface layer of thickness h and resistivity pi and a lower layer, extend-ing to infinity, of resistivity p2. It has been shown by Lancaster-Jones2 that the apparent resistivity, obtained by an application of equation 1 is related to the true resistivities, the depth h and the electrode separation a by an expression of the form pa/p1 = 1 + 4F [2] where Pa is the apparent resistivity and F is a function (actually an infinite series), of the ratio h/a, and a reflection coefficient k = (p2 - p1)/(p2 + p1). For given values of h/a and k, the right-hand side of equation 2 can be calculated, and curves drawn showing the relationship between Pa/P1, h/a and k. Such a set of curves for the case when pi > P2 is given in Fig. 1.

Jan 1, 1937

By Masayuki Otagawa

THE mining methods adopted in Japanese mines are less known to the mining world than those of other countries, owing to the geographical remoteness, but they present many features of interest to mining engineers. The Ashio copper mine is at the village of Ashio, in Tochigiken, about 109 mi. (175 km.) from Tokyo by the Imperial Government railroad. The area of the concession owned by the Furukawa Mining Co. is 5000 acres (5023 ha.). The mine was formerly divided into three, viz.. Honzan, Kotaki, and Tsudo, which are distant 3 mi. (4.8 km.) from each other as shown in Fig. 1. However, in 1914, when the writer was general manager, the three mining plants were amalgamated into one with the result of simplifying the working projects and increasing the operat-ing efficiency. The mine was visited-by the Institute party in November, 1911, when Mr. K. Inouye was the general manager. Shortly afterward, the writer was appointed manager, and, in 1915, he was succeeded by Dr. K. Asano. At the end of 1917, Mr. K. Kibe became general manager and, after two years, was succeeded by the present manager, Mr. I. Sugimoto-. For some time Dr. J. Kojima was acting general manager. It is needless to say that the gentlemen mentioned are all members of the Institute, as is also Baron T. Furukawa, president of the company. Since the discovery of the enormous masses, called "kajika" or "bullhead" deposits; which the writer has described elsewhere,' the mining methods have been varied to meet the different conditions presented by these deposits.

Jan 2, 1922