Search Documents

By R Lewis

Drill hole magnetometric resistivity (DHMMR) is a relatively recent addition to the explorationistsÆ suite of techniques for finding further resources in the vicinity of a drill hole. The method relies on gathering of an applied current into zones which are less resistive than the country rocks and it was first applied to exploration programs looking for weakly conductive sulphides, such as, for example, carbonate-hosted zinc deposits. More recently, it has been applied to a wider range of deposit styles, including highly conductive nickel sulphides. It has been found that the technique is capable of not only detecting mineralisation not seen by conventional electromagnetic (EM) techniques, but it can detect at a greater distance. Also, whilst EM is superior at defining tabular-shaped conductors, DHMMR may be more effective at finding cigar shaped sulphides. This paper presents a number of examples illustrating these findings.

Jan 1, 2000

Significance of Ion Interactions in Flotation in Saline and Brine Solutions

Sep 13, 2010

By James H. Rowland

The Mine Improvement and New Emergency Response Act of 2006 (MINER ACT) established a Technical Study Panel (The Panel) to provide recommendations on the utilization of belt air and new technology that may be available for increasing the fire resistance properties of conveyor belt used in underground coal mines. The Panel Report recommended use of the Belt Evaluation Laboratory Test (BELT) as the method for testing and approval of flame resistant conveyor belts used in underground coal mines. The research conducted to establish the correlation of the BELT with large-scale belt fire flammability tests was done using 36- to 42-in wide conveyor belt. Due to today?s coal haulage capacity, the mining industry is using 72-in and wider conveyor belts. The National Institute for Occupational Safety and Health (NIOSH) conducted a study to determine if the BELT will also qualify wider belts as fire resistant for use in underground coal mines. This paper describes the results of recent experiments comparing results from using the BELT and the large-scale tests for six different belts.

Jan 1, 2010

By V. Murugaiyan

The Geotechnical Engineer is faced to view problems emerging from the task of protecting the environment and also the problems related to prevention of natural hazarders. Geo-Environmental Engineering, based on the development of geotechnical engineering, addresses the problems for the industrial world and the impact on health and welfare in relation to pollution of the ground. In the recent years, acute land pollution due to indiscriminate discharge of industrial effluents especially Organic acid based effluents has become one of the major concern due to erosion in the privatization of sustainable development under Indian Scenario. To study the effect of chemical changes on soil properties due to amino acid effluent contamination on soil and erosion behavoiur. The changes in the soil properties of effluent contaminated clay and silty soil were experimentally observed to be due to the interaction of organic and inorganic constituents of effluent on index properties of soil. The surface reactivity of soil mass is experimentally reported to be varying proportionately with respect to clay (%) in the soil. Also higher surface reactivity of clay increases the Solid Retension Time (SRT) with increase in rate of chemical transformation of organic and inorganic solids within soil. Hence soil S1 (high clay content 54.5%) showed increased SRT and soil S3 (low clay content, high silt and clay content 94.9%) showed decreased SRT and long transformation stage.

May 1, 2004

The U.S. economy and, consequently, the demand for minerals grew at more moderate rates in 1995 compared with stronger performances the previous year. Demand for metals such as steel and copper was relatively stable. For example, the decline in steel consumed in motor vehicle manufacturing (reflecting lower vehicle sales) for the first half of 1995 was offset by an increase in steel consumed in construction during the same period. More detailed information on events, trends, and issues in the mineral and material sector Is presented below and in the commodity sections that follow. Overall Performance The value of processed materials of mineral origin produced in the United States during 1995 was estimated to be $395 billion, an increase of almost 10% compared with 1994. The estimated value of U.S. raw nonfuel minerals production in 1995 was $38 billion, about 7% more than in 1994. The value of U.S. minerals production has increased in 30 of the last 35 years.

Jan 1, 1996

A Life Cycle Assessment (LCA) of stainless steel production, including that of the nickel, ferronickel, ferrochromium and iron feedstocks was carried out using inventory data derived from the literature. The environmental impact categories considered in the study were Global Warming Potential (GWP), Acidification Potential (AP) and total (or full cycle) energy consumption. The effects of different sources of electricity (black coal, natural gas and hydroelectricity) were also examined in the study. The results of the LCA showed that when ferronickel is used as the nickel source, the total energy consumption for stainless steel production is approximately 50% higher than when nickel metal is used as the nickel source (75 MJ/kg cf. 49 MJ/kg). This result comes about largely because the Fe units in ferronickel have a much higher energy intensity than do the Fe units in pig iron, and the greater the use of the former at the expense of the latter, the greater is the total energy consumption. The results also showed that the production of ferronickel made by far the largest contribution (59%) to the total energy consumption for stainless steel production when this feedstock is used as the nickel source, but when nickel metal is used as the nickel source the contributions of the various stages are more evenly distributed. It was also observed that the electricity consumption of the electric furnaces used in the production of ferronickel, ferrochromium and stainless steel contributed approximately 50% to the total energy consumed in stainless steel production. Given the relatively low efficiencies associated with electrical power generation, significant reductions in the total energy of stainless steel production could be anticipated if more direct use of thermal energy was made in the ferronickel, ferrochromium and/or stainless steel smelting stages, for example by utilising bath smelting processes.

Jan 1, 2004

By José Rogério de Oliveira Júnior, Carlos Eduardo dos Santos, Geraldo Lúcio de Faria, Sidney Nicodemos da Silva, Rogério Felício dos Santos, Darlan Vale Bayão, Emiliana Cristina Marques Arthuso, Ivete Peixoto Pinheiro

A fase sigma () é conhecida por afetar negativamente as propriedades mecânicas e a resistência à corrosão dos aços inoxidáveis duplex (AIDs). Dessa forma, a exposição da liga a temperaturas elevadas durante os processos de produção, soldagem ou tratamentos térmicos devem ser realizadas de maneira cautelosa a fim de se evitar a precipitação da mesma. Assim sendo, modelos adequados para predizer a precipitação da fase são ferramentas muito úteis. Entre os numerosos modelos, a relação de Johnson-Mehl-Avrami-Kolmogorov (JMAK) é um dos modelos mais comumente utilizadas para descrever a cinética das transformações isotérmicas de fases em muitos sistemas regidos pelos mecanismos de nucleação e crescimento. Diante disso, o presente trabalho teve como objetivo realizar um estudo cinético baseado na aplicação do modelo JMAK, da precipitação da fase em um AID UNS S31803 envelhecido isotermicamente nas temperaturas de 750ºC, 800ºC e 850ºC. Concluiu-se que a cinética de precipitação da fase na liga obedeceu ao modelo JMAK, pois foi obtida uma boa correlação entre dados experimentais e os simulados. Observou-se que o aumento da temperatura de envelhecimento de 750ºC para 850°C acelerou a cinética de precipitação de A energia de ativação determinada (182,4 kJ/mol) para precipitação da fase neste sistema, sugere que a difusão do Cr na ferrita seja o principal mecanismo envolvido na formação dessa fase.

Nov 2, 2019

By Albert L. Toenges

The Deep River coal field is in Chatham, Lee, and Moore Counties, N. C. The coal-bearing part of the basin is about 35 miles long and 5 to 10 miles wide. Sanford, the county seat of Lee County, is the largest town in the area, with a population of 10,000. Four railroads provide transportation to the area, and four United States highways and improved county roads provide easy access to the field. The Carolina mine at Farmville is the only operating mine in the field. The mine was opened in 1921 by two rock slopes driven from the surface to the Cumnock bed. Mining operations continued intermittently until 1945 and then stopped. In the fall of 1947 the mine was reopened by the newly organized Raleigh Mining Corp.

Jan 1, 1952

Laboratory tests were conducted in a full-scale continuous miner test gallery to evaluate resulting dust levels for changes in face airflow, spray water quantity and pressure, and mining height. The minimum and maximum values tested for each parameter were as follows: airflows between 1.42 and 6.14 m3/sec, water flows between 56.8 and 132.5 lpm, nozzles pressures between 413 and 1379 kPa, and mining heights between 1.52 and 2.74 m. Each of these parameters were evaluated for four common spray system designs. Respirable dust samples were collected in the operator's cab on the miner and in the immediate return. Second-order polynomial models were used to represent expected dust levels and multiple stepwise regression was used to identify significant control parameters for inclusion in the models. Separate models were developed for dust levels at the operator and return locations and for each individual spray system. Interaction between control parameters and curvature effects were found in most models. The analysis indicated that at the operator location, airflow and mining height had the most significant impact on respirable dust levels. In the return, airflow and water pressure were typically the most significant parameters. The models developed for each spray system design can be used by mine operators to guide application of control parameters for a variety of operating conditions and mining heights.

Jan 1, 1994

By R. B. Moore

IN 1914 the writer and K. L. Kithil announced, through Bulletin 70 of the U. S. Bureau of Mines, that the United States possessed the largest deposits of radium-bearing ore in the world. At that time a small amount of this ore was being, mined and shipped to Europe, and one company was preparing to start the extraction and recovery of radium in this country. The importance of our carnotite deposits in Colorado and Utah up to the publication of Bulletin 70 was not, however, appreciated by anyone.. At that time the total supply of radium in the world was about 10 g., calculated as element, and when I estimated that at least 100 g. of radium element, and probably 200 g., would be produced from our carnotite deposits, there was a considerable amount of skepticism. Up to the present time almost 200 g. have come from this ore, and some writers put this figure a little higher. Uranium ore was found in the copper mines of the Union Minière du Haut-Katanga at Luiswishi in 1913. Later discoveries were made at other places in the Belgian Congo, and the Katanga ores now represent the largest supply of radium-bearing ore in the world. In fact, since 1923 very little radium has been produced from American carnotite, the Katanga ore representing practically the world's supply of. radium since that date.

Jan 1, 1930

By Jacolien P. Wyethe

Zincor uses a Roast-Leach-Electrowinning circuit to process zinc sulphide concentrates. It also processes zinc oxide fume, originating from a slag smelting operation in the Democratic Republic of the Congo (DRC). Zincor achieved an average zinc recovery of 90.3% during the period January 2006 to May 2007. The bulk of the losses occurred in the iron and lead silver residues, both as soluble and un-dissolved losses. The un-dissolved losses in the iron residue constituted around 33% of the total zinc lost from the circuit, and were largely attributed to the presence of zinc-ferrite in the calcine used for neutralization during iron removal. As part of Zincor?s continuous improvement programme, the un-dissolved zinc losses in the iron residue were targeted by: the partial replacement of calcine with zinc oxide fume (from the DRC); and the preferential use of ?low-ferrite content calcine? as neutralizing agents in the iron removal circuit. These initiatives, coupled with other operational factors, resulted in a marked improvement in recovery to 92.6% during June to December 2007. The zinc oxide fume, directly fed to the circuit, required investigation of the halide rejection capacity of the Zincor circuit. Rejection of chloride via the magnesium bleed operation was considered adequate. Fluoride was mainly rejected via the iron (~70%) and lead silver (~27%) residues. Fluoride rejection via the lead silver residue varied significantly, probably as a result of variations in the sparingly soluble CaF2 content in the feed. The mechanism for fluoride rejection in the iron residues is uncertain. The fluoride rejection capacity of the Zincor iron residue (comprising of mainly jarosites, schwertmannite and ferrihydrite) at 2 ? 4 mg/L F in solution, was estimated at 0.14 ? 0.19 kgF/tFe residue.

Jan 1, 2008

Study on Mineral Processing for a Cassiterite Ore in Southwest China

Sep 13, 2010

By K. E. Yassin, A. Yehia, M. Amar

Phosphate fines (size ≤ 45 μm), from the Red Sea Region, Egypt, were subjected to beneficiation process to recover the phosphorite grains from such fines. The sample is characterized by low P2O5 content (18.78%) associated with gangue minerals such as silica (22.77% SiO2) and carbonate (2.01% MgO) indicating its low grade. Phosphate pre-concentrate was prepared by gravity separation, using Falcon, where 63.37% of the phosphate, with 24.94% P2O5, 1.46% MgO, and 10.54% SiO2, was firstly recovered reducing the mass flow to the subsequent beneficiation process. However, the gravity tailing was the feed for the reverse phosphate flotation using bench scale column flotation where oleic acid was used as a carbonate gangue collector and amylase enzyme as a phosphate depressant. Under the appropriate flotation conditions (0.1% amylase, 5·10−4 mol/dm3 oleic acid, and temp. 30 °C), phospho-concentrate assaying 0.61% MgO, 13.14% SiO2, and 27.85% P2O5 with a P2O5 recovery of 55.45%, was finally obtained without the use of expensive depressants, e.g., phosphoric acid or sodium silicate. A tentative flow sheet for the whole process was postulated.

By I. Ciabatti

Inorganic salts of hexavalent iron (ferrate (VI)) are versatile reagents for water and industrial effluent treatment because of the strong oxidising effect of the ferrate ion (FeO42-) and the well-known coagulation properties of the resulting ferric ion. Among other applications, ferrate can effectively remove arsenic, cyanide and phenols from industrial effluents. Furthermore, ferrate salts can be prepared from ferrous sulphate, a common byproduct of the steel and titanium industries, and possibly from other iron wastes. Notwithstanding their many potential advantages, the industrial-scale application of ferrate salts, such as potassium ferrate (K2FeO4), for effluent treatment has been hindered by the difficulties inherent in their synthesis and stabilisation. Within a project co-funded by the European Commission, the large-scale synthesis of stabilised potassium ferrate was realised through a new synthesis process, and different applications of the resulting ferrate to effluent and wastewater treatment are under investigation. This paper reports the results of the application of stabilised potassium ferrate for the purification of textile effluents. Laboratory and pilot-scale tests were carried out and the performance of the ferrate was compared to that of chemicals currently used in wastewater treatment. According to these experiments, potassium ferrate is a promising reagent for an effective treatment of textile and other industrial effluents.

Jan 1, 2006

By H. B. Brunot

A complete list of permissible mine equipment, tested and approved by the Bureau of Mines previous to January 1, 1947, was published as Information Circular 7432.2/ A list of permissible mine equipment tested and approved by the Bureau of Mines during the calendar years 1947, 1948, and 1949 was published as Information Circular 7569. The present list supplements Information Circulars 7432 and 7569 and includes all of 'the equipment approved during the calendar year 1950. Information Circular 7465, which included a list of permissible mine equipment tested and approved by the Bureau of Mines during the calendar year 1947 therefore is superseded.

Jan 1, 1951

By T. Szendrei and S. Tose

Historical approaches to the problem of flyrock based on correlation studies and regression analysis, including artificial neural networks and similar techniques, are inherently incapable of addressing two core issues – root causes of flyrock and projection velocity. A further shortcoming of correlation techniques is that they give no information on the influence of rock size and shape on the flight distance. The scaled depth of burial model for crater blasting in the collar zone and bench face does not specifically address the question of flyrock velocity. A third approach, based on flight trajectory calculations, often neglects the very significant effects of air resistance on the trajectory. Some trajectory models incorporate air resistance but use an implausible fragment velocity model that cannot propel sizeable rocks to distances much beyond 150 m. Nonetheless, trajectory calculation incorporating the effects of air drag affords the most promising approach to the prediction of flyrock range. A unique and insightful feature of the proposed realistic flight modelling is that it collapses all suspected causes of flyrock, many of which are not well understood, to just a single parameter – the launch velocity. This indicates that the root causes of flyrock lie in the mechanisms of momentum transfer to broken rock and suggests new avenues of study.

Dec 13, 2022

By S Bluhm, LádeáOliveira, R Funnell

Taquari Vasouras potash mine (Vale Fertilizantes) has many interesting features including virgin rock temperatures of 50¦C at depths of 700 m. The mine has a relatively small shaft system with limited ventilation carrying capacity, which was not adequate to exploit the full extent of the deposit. This limitation was overcome by installing two large-scale recirculation systems with underground reconditioning centres. This paper describes this unique mine ventilation and cooling system and some of its history over the past two decades. The two controlled recirculation systems have been operating safely for some ten years and the use of large-scale recirculation has been a fundamental component in the increase of production and extending the mining further-and-further from the shaft centre. The recirculation systems have played a huge role in the mine profitability and comprehensively extending the mine life. The paper also discusses a number of novel design and operating features such as reverse running pumps for energy recovery. The underground chilled water system design required a number of special safety features in order to minimise the risk of water leakage since this could be catastrophic in a potash mine. This paper describes a good example of a mine in which the final ventilation and cooling system design ends up very different to what was envisaged at the greenfields stage.CITATION:Bluhm, S, Funnell, R and de Oliveira, L, 2013. Controlled recirculation and refrigeration at ValeÆs Taquari Potash Mine, in Proceedings The Australian Mine Ventilation Conference , pp 237-248 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By D J. Williams, A K. Kho, A Shokouhi, N Tucker

The disposal of dewatered coalmine tailings and coarse reject within spoil piles is gaining popularity as a means of eliminating separate surface tailings storage facilities or dams. The contrasting characteristics of coalmine spoil, coarse reject and tailings are somewhat complimentary, making the co-disposal of dewatered tailings within spoil piles geotechnically feasible and environmentally attractive. However, the impacts of mixing plant rejects within spoil piles are not well understood; in particular, the effects of water draining from the mixed plant rejects on the moisture content of the surrounding spoil. Changes in moisture content can cause additional collapse and degradation settlements of the spoil pile. A series of laboratory tests has been undertaken on mixtures of dewatered coalmine tailings, coarse reject and spoil. The results of these tests have been incorporated into a spreadsheet-based settlement prediction tool to investigate the effects of incorporating mixed plant rejects on total spoil pile settlements. This paper presents the laboratory tests undertaken, the incorporation of the test data into the settlement prediction tool, and settlement estimates for the various mixtures at different stages of construction.CITATION:Kho, A K, Tucker, N, Williams, D J and Shokouhi, A, 2015. Impact of co-disposing mixed plant rejects on spoil pile settlements, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 51–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Duane A. Smith

They are gone now. Gone like that long ago generation that gave them birth. The Homestake Mine, nestled in the northern Black Hills, closed in 2001 after 125 years, the longest run of any major American gold mine. The Homestake Mining Co., which guided its destiny for those many years, is gone too. It merged with Barrick Gold. The Hearst family, which guided the early destiny of both, has long since gone beyond its mining heritage and into the national and even international spotlight. The mine and the company passed from the scene with as little fanfare as heralded their birth, amid the Black Hills gold rush of the 1870s. They both grew into American mining legends, as did the town they sired and nurtured, Lead. In a real sense, the mine and the company symbolized one of the last links to a vanished world and a mining era.

Jan 1, 2003

By Charles J. Cohen, Donald F. Reed

"INTRODUCTION AND ACKNOWLEDGMENTSThis report supplements a previous report on work done in this same area 4/ but covers only the period from November 1945 to November 1946. The project was established in 1943 to investigate magnetite deposits in the northwestern Adirondacks by geophysical surveying and diamond-drilling for the purpose of increasing iron production in the eastern United States.In its program of investigation of mineral deposits, the primary objective of the Bureau of Mines is the more effective utilization of our mineral resources, that they may make the greatest possible contribution to our national security and economy. The policy of the Bureau is to publish the facts developed by each project as soon as possible after its conclusion. Maps showing the detailed magnetic surveys of the deposits and anomalies discussed in this report are on open file at the offices of the Bureau of Mines, College Park, Md., and at the University of the State of New York in the office of the Director of the State Science Service, Educational Building, Albany, N. Y.The Mining Branch, Lowell B. Moon, chief, conducts preliminary exami¬nations, performs the actual investigations, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.The chemical analyses included in this report were made at the Eastern Experiment Station of the Bureau of Mines at College Park, Md., under, the general supervision of J. B. Zadra, chief, College Park Division, Metallurgical Branch, and the immediate direction of Dr. Alton Gabriel, in charge of the laboratory service unit."

Nov 1, 1947