Search Documents

By Paul Kunze

We have been told many times by legal folks and insurance types about the importance of producing accurate blast reports should you ever get dragged into court. In that venue the investigators will look at the information regarding product type and quantity, it’s distribution among the holes, and delay information in order to arrive at some judgement regarding vibrations or other blast induced phenomena

Jan 1, 2003

By O. C. Blade

The southeastern region of the United States is becoming more important as a petroleum-producing area, and it is receiving increasing attention from oil operators. In 1948 total production of crude oil from six southeastern States - Alabama, Florida, Kentucky, Mississippi, Tennessee, and Virginia - was 55,244,000 barrels, which represents 2.7 percent of the Nation's output during that year. Kentucky and Tennessee have produced crude oil since the early days of the industry, but the remaining four States have had production only few years. Data on annual production of crude petroleum in the six States are given in table 1.

Jan 1, 1950

By Eric R. Borys, Amaneh E. Kenarsari, Brett Gitskin

This case study discusses impacts of excessive Earth Retention System (ERS) lateral movement at a project in city of Chicago. The ERS (cantilevered sheeting) moved inward towards the excavation and caused lateral displacement and cracks in six drilled shafts located about 1 to 2 lateral feet (0.3 to 0.6 m) from the face of the sheet pile wall. Up to 9 inches (23 cm) of horizontal movement was observed on top of the supporting sheet-pile. Similarly, survey measurements showed the top of the drilled shafts moved laterally up to 8 inches (20.3 cm). To evaluate the cause of failure and determine a remediation solution, the soil, shaft and site conditions were investigated. Pile Integrity Tests (PIT) were conducted at the affected drilled shafts. The shafts with identified anomalies were cored and video-recorded. The cause of the failure was determined to be related to variable soil conditions across the site, deeper excavation (i.e., increased effective ERS wall height), and other differences between design and as-built conditions. Internal bracing, in the form of walers and rakers, was installed to limit further movement of the sheet pile as a short-term solution, with additional grade beams framed into the basement slab-on-grade as a long- term solution. Five of the six cracked shafts were spliced with reinforcing bars and high strength grout and one shaft was replaced. INTRODUCTION The subsoil in the Chicago Area mostly consists of glacial till clays underlain by water-bearing granular soil over bedrock. The glacial clays have very soft to medium consistencies for a typical thickness of 30 to 50 feet (9.1 to 15.2 m) below which hard clays (Hardpan, i.e., heavily over-consolidated clay soils) are encountered. The soft clays are often referred to as the “Chicago Blue Clay”. Beach Sands are also found above upper soft clays in several areas, especially within a three-mile strip near Lake Michigan (Peck and Reed 1954). Due to the existence of soft clay in Chicago area, supporting the mid to high rise buildings on drilled shafts extended to Hardpan is a common practice in modern building design. In the early 19th century it used to take about 3 weeks to excavate 1 shaft hole and about 1½ days to fill the shaft with concrete in Chicago (Manierre 1916). The early 19th century methodology of excavating a shaft consisted of hand digging the shaft, installing wood lagging as temporary shoring with spoils removed with a rope and pulley system from the surface. Today, the excavation of a typical drilled shaft in Chicago uses heavy drilling equipment and requires much less time for excavation and concrete placement. It is not uncommon for contractors to excavate shafts and place concrete at a rate of about 2 to 5 drilled shafts per day (with one drill rig).

Jan 1, 2018

INTRODUCTION This paper was originally presented at the Platinum Adding Value Conference, held at Sun City from the 4th to 6th October 2004. Narrow reef mining may not be applicable to the base metal operations in Zambia, however, it is considered that the methodology used is equally appropriate to the development of technology and mining methods in mining environments other than narrow reef mining. The purpose of this paper is to explore the integration of technology and stoping systems. For the last hundred years the South African narrow reef mining industry has battled to control working costs in a labour intensive industry. It is only through the application of appropriate technology that change will occur. Stoping systems, because it is the stoping method and methodology that is at the heart of the mining system. Introduce a different technology that results in a more efficient stoping system and the mining system will look after itself. The technology applied to stoping in narrow reef mining, over the last 100 years, can be categorised as follows: ? The introduction of pneumatic rockdrills early this century. The cumbersome rig mounted units being replaced by smaller, lighter, hand held units that were then made easier to use with the addition of an air leg. (The so called Swedish method of mining.) As late as the early 1970s some drilling was still being carried out without the assistance of an air leg. ? Scraper winches to replace gravity and shovels to move rock both in the face and the gullies were first introduced in the late 1920s. ? Hydraulic props installed close to the face and capable of applying force against the hangingwall as well as yielding in a controlled manner under dynamic load arrived in the 1960s. In many instances these have now been replaced by yielding elongates fitted with water hydraulic tensioning devices. ? Some people argue that the introduction of tungsten carbide inserts, to improve drilling, was equally important.

Jan 1, 2005

By L. Stein

A simplified radiochemical method has been developed for quantitatively analyzing; radon gas in underground uranium mines. In this method, a measured volume of air is drawn by a pump through a drying tube and a cartridge containing dioxygenyl hexafluoroantimonate reagent. Radon is captured as n nonvolatile product. After radioactive equilibrium has been established between radon and its short-lived daughters (approximately 4 hours), the gamma-emission of the cartridge is measured with a scintillation counter. The amount of radon is then calculated from the gamma-emission rate. The effect of cartridge geometry, reagent load, and air flow rate upon collection efficiency and counting efficiency is reported.

Jan 1, 1977

By D. J. Leidel

The offshore production of oil and gas resources has been active in the Gulf of Mexico since Kerr- McGee drilled the first commercial well out of the sight of land in 1947. Since then, approximately 60% of the offshore oil/gas production structures used globally have been erected in the GOM to support the production of energy resources’. The shallow, shelf and shelf edge waters of the Gulf of Mexico have reached or are rapidly approaching production maturity, requiring that the fixed structures used to support energy production be removed or otherwise disposed of by suitable means. The use of energetic materials has been determined to be a safe, efficient and cost effective technology to remove fixed offshore structures whose service life has been exceeded.

Jan 1, 2002

By I. R. Hanby

A simple but comprehensive method has been developed for the simulation of a mechanical-drive dump truck that enables various parameters to be predicted as a function of time throughout its whole cycle. Uses of the simulation results are indicated with specific attention to environmental and operational or economic planning. The output of a sample run is presented. The method can be easily adapted for the investigation of a wide variety of mobile plants.

Jan 4, 1992

Goldfields (Tasmania) Limited operates a small, high-grade underground gold mine on the West Coast of Tasmania, 30 kilometres north of Queenstown. The main orebody, Zone 96, was discovered in 1989, with major development work commencing in 1993. The mine was officially opened in July, 1996. Initial production came from a shallow orebody known as the Sill Zone, some 50 - 150 m below surface, which was accessed by a 1 in 8 decline. Zone 96 lies between 350 m and 550 m below the surface and is accessed by a 402 m deep, 3.2 m diameter internal shaft from the collar level located 100 m below surface. The main ore extraction system in Zone 96 is mechanised cut and fill, using high density paste fill. Run of mine ore and waste are hoisted in a single 5.5 tonne overturning skip, then trucked from the underground collar to the gold plant ROM pad or waste dump, respectively. Ground conditions in the mine vary with orientation and proximity to major faults. The gold is contained in a sequence of strongly altered volcanic rocks adjacent to the Henty Fault. Most of the gold is contained in massive quartz, ranging in width from 0.5 m to 7 m, which has been subjected to substantial faulting. Average mineable grade is about 27 grams gold per tonne. Ore reserves in 1996 proved an initial mine life of approximately 4.5 years at 90 000 ounces gold per annum, with significant potential for additional resources from extensions to Zone 96 and adjacent zones. The lease is located in an environmentally sensitive area and a very high standard of environmental management is an essential part of the operation. This paper describes the relevant aspects of mining at Henty including grade control, ground support, backfill placement and environmental management.

Jan 1, 1998

This is the fourth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-363/. The second report gave the same data? for motor gasolines sold during the summer of 19364/. The third report of the series gave the same data for motor gasolines sold during the winter of 1936-375/. This report covers 63 brands of gasoline represented by 1,136 samples excluding the Pacific Coast. Those from the Pacific Coast were averaged by the Pacific Coast technical group before being submitted and are published exactly as they were submitted. In some areas reports were received from five or six companies on the same brands of gasoline, whereas in other areas only one company reported on a brand. Thus, it can be seen that some of the data are more representative than others.

Jan 1, 1937

This is the fourth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-363/. The second report gave the same data for motor gasolines sold during the summer of 19363/. The third report of the seriis gave the same data for motor gasolines sold during the winter of 1936-375/. This report covers 63 brands of gasoline represented by 1,136 samples excluding the Pacific Coast. Those from the Pacific Coast were averaged by the Pacific Coast technical group before being submitted and are published exactly as they were submitted. In some areas reports were received from five or six companies on the same brands of gasoline, whereas in other areas only one company reported on a brand. Thus, it can be seen that some of the data are more representative that others.

Jan 1, 1937

By Antoine F. Mulaba

Introduction Copper and cobalt oxide mineral deposits formed by the atmospheric weathering of near surface sulphide deposits are commonplace in the Democratic Republic of Congo. The most common route for the extraction of these metals is a hydrometallurgical one in which the base metal oxides are dissolved in sulphuric acid and then concentrated further by solvent extraction. However, as many of these deposits are relatively low grade (i.e. 0.5-1.8%Co and 2-4% Cu) and can also contain large amounts of acid consuming gangue minerals (i.e. dolomitic, micaeous, and/or siliceous), the hydrometallurgical route becomes uneconomic due to the excessive acid leaching costs. Some means of pre-concentration ahead of leaching is then desirable to improve the process economics. Apart from the small scale mining (Pan. Afr. News Agency, 2000) handpicking, although not easy, oxide concentration by flotation has been suggested. For the flotation process, the two most common approaches are controlled potential sulphidisation (CPS) and the fatty acid flotation method. The preferred method is dictated by the nature of the mineral makeup of the gangue. Being secondary deposits, the gangue associated with these ores is often complex and can play a significant role in the overall flotation efficiency. Laboratory flotation experience gained from the testing of a number of different ores of this type has revealed that it is not possible to prescribe a set method for the flotation of various ore types. Each ore needs to be analysed very carefully before and after laboratory flotation on an individual basis in order to arrive at an acceptable flotation technique Laboratory flotation testwork was carried out on three different samples from the DRC in attempts to isolate some of the more important variables affecting the flotation of copper and cobalt oxide minerals from these weathered deposits. This paper describes some early results achieved and experiences gained with these different ores ahead of a more detailed flotation test program which will follow in the near future on receipt of a significant quantity of a more representative sample. Controlled Potential Sulphidisation (CPS) was used in an attempt to achieve acceptable recoveries of both copper and cobalt.

Jan 1, 2005

By William R. Yernberg

Most citizens take it for granted, but minerals produced in the mines of the western United States, including Colorado, are crucial to nation’s standard of living and quality of life, said Colorado’s Gov. Bill Owens in his welcoming remarks at the 106th National Western Mining Conference. The conference, which was organized by the Colorado Mining Association (CMA), was held Feb. 4-6, 2004, in Denver. Attendance was425, up substantially from last year’s meeting. The meeting included the CMA annual membership meeting as well as the CMA chairman’s and president’s reports. The meeting also included awards presentations in which companies were recognized for their efforts in pollution prevention, health and safety, and reclamation. The conference also included a tradeshow.

Jan 1, 2004

During the lifetime of an open pit mining project, each stage from exploration activities to exploitation and mine closure produces disturbances on the mining region. Mined land reclamation plans establish constructive solutions to rehabilitate the disturbed areas. Open pit mining as an effective method for exploitation of a wide range of orebodies especially for massive reserves of shallow metallic substances has exhaustive and harmful environmental effects on the mining project region. Nowadays, closure and reclamation stage in a mining project is emphatically enforced by the relevant environmental protection regulations in many countries. It is therefore obvious that closure and reclamation costs of an open pit mining project, as costs of other stages of project, must be estimated to enter the planning and design processes in open pit mining. Post-mining land use is the most important factor to recognise closure and reclamation costs. Thus, using a model to define optimal land use in planning phase of an open pit mining project is necessary in this regard. In this project a model was developed to define optimal land use regarding different sections of open pit mines such as pit(s), waste dump(s), tailing pond(s), roads, areas for onsite facilities and free land zones which are not mined. TOPSIS and PROMETHE techniques were applied to create the developed model. Lumber production was recognised as the optimal post-mining land use for the pit area of the case study in this project.

Dec 6, 2010

By Kenneth G. Skinner

Diatomite, also known as diatomaceous earth, diatomaceous silica, kieselguhr, and moler, has been used extensively for many years, but only during the past two decades has it become an important industrial mineral. United States sales for 1.936-38 totaled almost 280,010 tons,7 but relatively little (with the exception of that sold by an Oregon company affiliated with a larger California company) was sold by Pacific Northwest producers. In attempting to develop some of the many Pacific Northwest diatomite deposits, these producers have been handicapped by lack of published technical information regarding processing methods and the suitability of different deposits for specific uses. To determine some of the physical and chemical properties of known Pacific Northwest diatomites, the present investigation was started in 1938 by the Bureau of Mines in cooperation with the College of Mines, University of Washington. Figure 1 shows the location of deposits sampled. Because most relatively pure diatomites can be used as concrete admixtures or as inert fillers in rubber, paints, and plastics, this investigation concentrated upon determining some filter-aid characteristics and their relationship to other physical properties. A filter-aid is a powdered material that, when added to solutions to be filtered, improves flow rate, filtrate clarity, or both. Some chemical analyses also were made.

Jan 1, 1944

By Nural Kuyucak

Several thousand years ago, metallurgists discovered that by combining two relatively soft metals, copper and tin, they could make a new material, bronze, that was stronger than either metal separately. Bronze and other alloys show how different materials can be integrated to create something new and better. Today?s mining industry can likewise find benefit in an integrated approach to managing the external impacts it has through its waste materials and its use of water. Just as using bronze gave ancient nations an economic and military advantage, mining companies can gain competitive advantage through finding better ways to manage water and waste. Trends pushing this include: ? Environmental ? Regulations on water-taking and the quality of discharged water are becoming more stringent. Net zero discharge requirements are often imposed by regulators. Mining companies also come under pressure to manage environmental impacts of mine waste, including minimizing the area occupied by waste and seepage amount resulting from infiltration of water from a smaller surface area. ? Social ? Particularly in arid parts of the world, there are multiple possible uses for each gallon of water. Local residents do not want to see a reduction in supplies of water for agricultural, domestic, manufacturing and other purposes. They get suspicious about any potential impact of water being mixed with their water reservoirs if it comes from a mining site, even if it would be treated. Such suspicions may cause conflicts among the stake-holders and delays in project approval processes.

Jan 1, 2009

By William R. Yernberg

The Mineral Processing Plant Design, Practice and Control Conference was held from Oct. 20through 24, 2002, at the Fairmont Hotel, Vancouver, British Columbia, Canada. The conference was attended by nearly 400 of the world’s top mineral-processing specialists, including plant-design engineers, mineral-processing consultants, academics, suppliers and equipment manufacturers. The meeting was sponsored by SME and cosponsored by the Canadian Mineral Processing Division of the Canadian Institute of Mining, Metallurgy and Petroleum (CIM). The conference covered all aspects of mineral-processing design, construction and operation. The meeting included more than 130 technical presentations. Topics included sampling programs, feasibility studies, design criteria, process technologies, construction, start-up operations and shutdowns. To stimulate interaction and discussion throughout the five-day conference, the sessions were presented consecutively. Attendees had the opportunity to attend every session.

Jan 1, 2003

German manufacturer DBT signed a contract to supply a sixth automated-plow long-wall system to Shenyang Coal in Liaoning province in northeastern China. This most recent order occurred just weeks after DBT signed a contract to deliver a fifth automated-plow longwall system to Datong Coal in Shanxi province. The plow will go into service at Shenyang Coal’s Hongyang Mine. Mining conditions at the mine, coupled with DBT’s advanced automated-plow technology, means that the system has the potential to become one of the world’s most productive thin-seam longwalls.

Jan 1, 2004

By Pat McLaughlin

Blast design in the construction industry has often been based on past practice or powder factors. This is to some extent understandable, since construction projects do not have the longevity of mining or quarrying operations and therefore have less opportunity to pursue potential improvements. The main concern of the operator is whether or not the technique will work, and at what cost to the downstream processes. Time, not long term savings, is of the essence.

Jan 1, 1994

By Xiangjun Zuo

This paper firstly reviewed the state of the art in the recycling of used Printed Wiring Boards (PWB), and then presented part of the authors study on the combustion of PWB powders with and without the addition of catalyst. During the combustion of PWB powders without catalyst addition, there were two obvious exothermic reactions, one at 300-380oC, the other at 450-500oC. With the addition of catalyst during PWB combustion, there were no obvious exothermic reactions, indicating that dehalogenation reactions are not exothermic: The results showed that NaHCO3 and CaCO3 were very efficient to control the emission of Br2 and C6H6, lowering 80% compared to the case without catalyst, Na2CO3 can slightly control the emission of Br2 gas but not for C6H6 gas mission, and NaOH has no any effect of the control of both gases.

Jan 1, 2009

By Ximing Yuan, Yongsheng Xu, Hongjie Li

A study of a static demolition agent that can be used underwater has been carried out. A new type of granulated static demolition agent with rapid reaction has been tested in several hundred experiments. It can be used conveniently and simply in the field. It demonstrates a fast reaction rate with high expansion pressures. The important characteristic of the new type of granulated static demolition agent is the ability to function underwater. It will destroy rock and the other brittle material without flyrock, vibration, shock wave, toxic gas or noise. The reaction rate can be controlled within 30-60 minutes. It is difficult to use these products when the reaction rate is less than 30 minutes and it is less efficient when the reaction rate is longer than 60 minutes. The reaction rate is slightly increased after the material is kept in storage for two years. A new type of the hydraulic device that is used to measure the expansion pressure of solid materials has been designed. The expansion pressure of the granulated static demolition agent has been tested with the device. It is shows that the expansion pressure of the granulated static demolition agent can get to 80~120MPa in 60 minutes. Also included is a discussion of the thermodynamics of the static demolition agent.

Jan 1, 2003