Search Documents

By Yuemin Zhao, Daniel Tao, Xinxi Zhang, Qingru Chen, Maoming Fan, Zhenfu Luo, Xiuxiang Tao, Guohua Yang

Coal is currently cleaned with the minimum of size reduction, fine particle processing, recovery, and tailings disposal are major problems. Adequate water resources are not always available. For example, two thirds of China's coal is located in arid areas. Hence, dry separation provides an alternative approach. Of the dry coal separation methods available, air dense-medium fluidized beds have been used to separate 50~6mm coal efficiently. However, excessive bubbling and back mixing of the separated solids in the air-dense media fluidized bed causes the high lower size limit of 6mm for the feed material, this affecting the preparation efficiency. Based on prior study on air-fluidized dense media for 6~50mm coal preparation, this paper presents methods and test results on the fine coal dry classification, static electricity beneficiation of 0~0.5mm coal, and magnetically stabilized fluidized beds for separating 0.5~6mm coal.

Jan 1, 2005

By C. Tan, C. Detournay

Wellbore stability is a major concern for drilling in naturally fractured formations. The infiltration of drilling mud into the fractures is a factor, which may compromise wellbore integrity due to the loss of strength experienced by the fractures. The reduction in the fracture frictional and cohesive properties is attributed to weakening of the infill materials and lubrication of fracture asperities by the mud filtrate. One way to investigate the influence of mud infiltration on wellbore stability in fractured formations is to use a numerical modeling approach. A requirement for the numerical model is the ability to predict the region of mud infiltration. This paper describes a numerical technique to model the extent of mud infiltration for application in coupled fluid-mechanical simulations in densely fractured rock masses using the computer code, UDEC. Several factors are considered including fracture pattern, in-situ stresses, reduction in joint frictional angle and cohesion, viscosity of the mud filtrate and fracture plugging. Results of numerical simulations are presented to illustrate the technique and show the influence of these factors on the extent of mud infiltration. Un des problèmes importants posés par le forage en milieu fissuré saturé, est celui du maintient de la stabilité du puit. L’infiltration de boue de forage dans le massif peut avoir pour effet de réduire les propriétés frictionnelles et cohésives des fractures et de compromettre ainsi la stabilité du puit de forage. Le radoucissement des propriétés des fractures est attribué à la dégradation du materiau de remplissage et au pouvoir lubrifiant des boues. L’analyse numérique offre un moyen d’investiguer l’influence jouée par l’infiltration de boue sur la stabilité du puit. Un des critères de sélection du modèle numérique sera son pouvoir de prédiction du domaine d’infiltration de boue. Cet article décrit une technique numérique permettant de modéliser l’infiltration de boue de forage dans le cadre de simulations hydro-mécaniques, en milieu à haute densité de fractures, effectuées avec le logiciel de calcul UDEC. Parmis les facteurs tenus en compte, on trouvera la nature du réseau de fractures, les contraintes in-situ, le radoucissement en friction et cohésion des joints, la viscosité de la boue et le bourrage des fractures. Des résultats de simulations sont présentés pour illustrer la technique et montrer l’influence de ces facteurs sur la taille du domaine d’infiltration de boue. Bohrlochstabilität ist ein wichtiger Aspekt für das Bohren in geklüfteten Gebirgsformationen. Das Eindringen der Bohrlochstützflüssigkeit in die Klüfte kann die Bohrlochintegrität wegen des Verlustes der Festigkeit des Kluftsystems gefährden. Die Reduktion der Reibung und kohäsiven Eigenschaften ist der Schwächung der Kluftfüllung und der Schmierwirkung der eingerungenen Stützflüssigkeit in Bezug auf die Kluft-Asperities geschuldet. Numerische Berechnungen sind ein Weg zur Untersuchung des Einflusses der Infiltration der Bohrlochstützflüssigkeit auf die Bohrlochstabilität in geklüfteten Gebirgsformationen. Eine Voraussetzung für numerische Modelle ist die Fähigkeit den Bereich der Infiltration der Stützflüssigkeit zu prognostizieren. Diese Publikation beschreibt ein numerisches Verfahren, um die Reichweite der Infiltration von Stützflüssigkeiten mittels fluid-mechanisch gekoppelter Simulationen im engständig geklüfteten Gebirge mit dem Programm UDEC zu modellieren. Verschiedene Faktoren, wie Kluftmuster, Gebirgsspannungszustand, Reduktion von Kluftreibungswinkel- und kohäsion, Viskosität der Stützflüssigkeit und Rissabdichtung wurden untersucht. Ergebnisse numerischer Simulationen werden präsentiert, um die Vorgehensweise zu illu

Jan 1, 2003

By N. Kinoshita, Y. Inada

The authors have proposed and discussed storage of low temperature materials such as LNG, LPG and frozen food in rock caverns. In this case, as the rock mass around the caverns will receive effects of low temperature, it is necessary to consider the thermal behavior and the stability of caverns. In this study, strength and deformation characteristics obtained by the uniaxial tension test and the compression test at low temperatures were discussed. Using the results, temperature and stress distribution around caverns when LNG was stored, were analyzed. Then thermal behavior of the rock mass around caverns was discussed. Die Autoren haben Lagerung von Niedertemperatur-Materialien wie LNG, LPG und tiefgefrorenen Nahrungsmitteln in Felskavernen vorgeschlagen und diskutiert. Da in diesem Fall die Felsmasse um die Kavernen den Effekten der niedrigen Temperatur ausgesetzt ist, ist es erforderlich, das Thermalverhalten und die Stabilität der Kavernen zu berücksichtigen. In dieser Untersuchung wurden Stärke-und Deformationseigenschaften, die durch ein-axialen Spannungstest und Kompressionstest bei niedrigen Temperaturen erhalten wurden, diskutiert. Mit diesen Ergebnissen wurden Temperatur- und Stressverteilung um die Kavernen bei Lagerung von LNG analysiert. Dann wurde das Thermalverhalten der Felsmasse in der Umgebung der Kavernen diskutiert. Les auteurs proposent et discutent l'entreposage de matériaux à basse température, tels que le GNL, le GPL et des aliments congelés, dans des cavités rocheuses. Comme, dans ce cas, la masse rocheuse entourant la cavité subit les effets des basses températures, il est nécesaire d'étudier le comportement thermique et la stabilité des cavités. Dans cette étude, les auteurs discutent des caractéristiques de résistance et de déformation, obtenues par essai de tension uniaxial et essai de compression à basse température. En se servant des résultats, ils analysent la répartition de la température et des pressions autour des cavités, lors du stockage de GNL. Ils discutent ensuite le comportement thermique de la masse rocheuse autour des cavités.

Jan 1, 2003

By M. Suzuki, T. Shiomi, M. Nakada, K. Tsutsumi

Mold powder plays an important role in the continuous casting process for high quality steel production. It is well known that mold powder entrapment causes surface defects in steel sheet and the high viscosity of mold powder prevents the entrapment of mold powder in molten steel in ultra low carbon steel. This paper deals with the entrapment of mold powder caused by suction by Karman?s vortex in a laboratory experiment. At first the effect of the viscosity of oil and interfacial tension between water and oil was investigated in a water model experiment. Then hot model experiments were carried out by mold powder and molten steel. The amount of mold powder entrapment was affected by the viscosity and the interfacial tension between molten steel and mold powder. As a result, the following equation of the mold powder entrapment was obtained. m=1.06*107?-0.255?m-s-2.18 The amount of mold powder entrapment decreased when the viscosity and interfacial tension increased. But the effect of viscosity was larger than that of interfacial tension in the case of the industrial mold powder when the viscosity was under 0.5 Pa.s, interfacial tension was from 1200to 1300 mN/m.

Jan 1, 2004

By W E. Short

Ausmelt top submerged lance technology is at the cutting edge of technological developments in non-ferrous metal smelting with commercial operations throughout the world. The Technology is being used for lead smelting, copper smelting and matte converting, fuming zinc from slags, recycling iron residue from zinc plants, processing the aluminium industry hazardous waste SPL , precious metal processing, nickel-copper residue smelting and converting, and tin smelting. The Technology is also being developed for projects involving iron-making and waste industry opportunities. There are 19 furnaces operable or under design at the time of writing. The benefits to operators using Ausmelt Technology vary depending on application, but typically result from environmental improvements, enhanced recovery of valuable products, lower capital and operating costs, more flexible operations capable of handling a wide range of feed materials, better removal of impurities, or improved product quality. Growing industry acceptance of the Technology is evidenced by the fact that more than 20 per cent of the worldÆs tin production will be extracted in systems using Ausmelt Technology when the Yunnan Tin Corporation plant starts up in 2001. Metallurgists, industrialists and investors have accepted the Technology for improved operations in both greenfield main smelters and add-on plants in Korea, China, Japan, Germany, Peru, Zimbabwe, India, Namibia and Australia. Ausmelt intends that this paper will update the industry by outlining recent achievements of the Technology in global metallurgical operations.

Jan 1, 2000

By R. Zivojinovic, S. Vujic

The structural age of the capital mining machinery, representing a part of the system of the Electric Power Industry of Serbia, has been dictated by the initiation and development of open pit coal mines. For example, the oldest bucket wheel excavators were installed some thirty-four years ago, and the average life of the relevant machinery exceeds twenty-two years. Operation of both capital equipment and machinery has direct effects on economic and business activities of open pit mines, and consequently forced us to make a decision and study thoroughly the problem of establishing the optimum exploitation life of capital mining equipment at the open pit coal mines of the Electric Power Industry of Serbia. The aim of this paper is to define and discuss the relative problems as well as to find out the possible solutions and establish the methodology for estimating the optimum exploitation life of machinery. The study was successfully carried out by a team of scientists engaged from and coordinated by the Department of Computer Science of the Faculty of Mining and Geology, University of Belgrade. This paper presents the key observations covering the subject problem. Keywords: Mining, Opencast exploitation, Coal, Optimization, Exploitation life, Capital machinery, Electric power industry, Dynamic programming.

Jan 1, 2003

By M. Tanaka, K. Aoki, T. Mori, H. Morioka, K. Iwano, T. Kanagawa

To estimate the detailed characteristics of the rock around the cavern during excavation, new monitoring technique for dynamic properties of the rock has been applied. In this paper, micro-seismic monitoring and AE monitoring technique are applied to the excavation of large underground rock cavern and the result was discussed to clarify the acutal behavior of EDZ around the cavern. Zur Einschätzung der Gesteinseigenschaften um die Ausschachtung herum haben die Autoren eine Technik eingesetzt, mit der die physikalischen und dynamischen Änderungen im Gestein um den Schacht während der Ausschachtung beobachtet werden. In der vorliegenden Studie wurde zur mikroseismischen Überwachung ein AE Überwachungsverfahren eingesetzt und die Autoren berichten über die Veränderungen in den Gesteinseigenschaften um die Ausschachtung herum. Dans le but d'évaluer en détail les propriétés des roches qui forment les parois des cavernes creusées, les auteurs ont utilisé une technique de mesure permettant d’observer les modifications physico-dynamiques des roches aux alentours de la caverne pendant son excavation. Dans le cadre de cet article, une technique de surveillance de l’agitation et du bruit microséismiques a été mise en œuvre et les auteurs font état de la modification des propriétés de la roche environnante.

Jan 1, 2003

By Scott C. Vollmer

This paper seeks to examine some of the technical factors influencing the deflection of Mechanically Stabilized Earth (MSE) retaining walls based on the authors' field observation of numerous structures. Excessive deflections can be unsightly and can be perceived as wall failure. Deflections can cause cracking or gapping of the facing units and general misalignment. Deflection of the reinforced backfill zone behind the wall face can result in settlement of the backfill zone and adjacent pavement cracking. Deflections can be the result of excessive movement external or internal to the reinforced soil structure. This paper only examines internal factors affecting wall deflections. External factors such as foundation settlement are not discussed.

Jan 1, 2003

By L Lorenzen

In this paper, we developed and implemented a fuzzy logic expert system capable of evaluating the degree of sustainability within the context of gold mining operations. The newly introduced approach of evaluating sustainability in the gold mining industry has the merit of sufficiently handling diverse, sustainable, development-related qualitative and quantitative data owing to fuzzy logic technology capabilities in dealing with linguistic syntax. The economic, environmental and social indicator inputs were independently evaluated and then combined with the aid of fuzzy logic to provide an overall sustainability index on a scale of zero to one. A total of 66 independent indicators were identified and applied in our model. The novelty of this work lies in providing a coherent numerical and automated approach in evaluating sustainability in the context of gold mining operations. In addition, the model can aid policy- and decision-makers in arriving at consistent decisions regarding the degree of sustainability on various aspects of gold mining operations. The functionality of this model will be illustrated through several examples.

Jan 1, 2007

By Tomohide Takeyama, Yuki Yoshida, Masaki Kitazume

"Abstract A series of centrifuge model tests was conducted to investigate the failure pattern and stability of cement treated clay ground having an unsupported vertical slope. The model ground was subjected to monotonically increasing centrifugal acceleration until it failed due to the enhanced self-weight. The test results were compared with the numerical analyses in which the treated soil was simulated by the Smoothed Particle Hydrodynamics (SPH) method. In the simulation, the Dracker- Prager model is employed as the constitutive model. In order to simulate the brittle behavior of the cement treated soil, it is assumed that the unconfined strength is gradually reduced to a certain value which corresponds to the residual strength due to accumulated plastic strain. It was found that the simulation by using SPH method can express the brittle failure observed in the centrifuge model tests.IntroductionBecause of economical and environmental concerns it has become more difficult in recent years to obtain enough soil to construct reclaimed land for airports, electric power plants, manufacture plants and so on. On the other hand, it has become difficult to find and construct disposal sites for waste subsoil or dredged soil. These circumstances have encourage geotechnical engineers at present to use these poor quality materials as filling materials more than they were used one or two decades ago. Several soil admixture methods have been developed to improve their properties and to manufacture high quality fill materials.The deformation and strength characteristics of cement treated soils have been investigated in Japan, which have revealed that the treated soil is characterized by a brittle behavior with quite high compressive strength and quite small strain at failure, and the treated soil with relatively high strength shows tensile failure instead of shear failure. Regarding to evaluate the stability of structures adjacent to or buried in the treated ground, Kitazume (1998) and Kitazume et al. (2003) investigated the earth pressure of cement treated ground by the centrifuge model tests. And they emphasized that the failure pattern of the cement treated ground was much different from that of ordinary ground. After the Hyogoken- Nambu earthquake in 1995, many design codes for the seismic stability were revised in Japan, so that seismic stability must be evaluated more precisely. The dynamic earth pressure of ordinary grounds is usually calculated by a pseudo-static limit equilibrium method based on the Mononobe- Okabe’s method (Okabe, 1924; Mononobe and Matsuo, 1929). This calculation method is also applied to the cement treated ground, although its applicability has not been thoroughly clarified."

Jan 1, 2014

By Jacob Chacko

The east span of the San Francisco-Oakland Bay Bridge (SFOBB), which is one of the most heavily traveled bridges in the world, will be replaced due to seismic safety concerns. The majority of the new bridge will be founded on large-diameter (1.8 to 2.5 meters), approximately 60- to 100-meter-long pile foundations The large-diameter steel pipe piles and soil conditions are similar to those used/encountered in many offshore structures. Thus, the design methods used are based on site-specific modifications to the procedures recommended by the American Petroleum Institute rather than the conventional procedures that have been formulated and used for the design of much smaller piles. Pile foundations will experience their maximum loads during the design earthquake. For the Safety Evaluation Earthquake, tension loads of up to approximately 80 to 90 meganewtons (MN) and compression loads of up to approximately 120 to 140 MN were calculated. Due to the economic importance of the SFOBB and the consequences of catastrophic failure in both economic and human terms, the design and analysis of the pile foundations supporting the bridge consider a number of aspects of pile-soil behavior that are normally ignored. Those aspects include: 1) the effects of consolidation and setup, 2) the behavior under dynamic loading, 3) the losses of resistance under cyclic loading, and 4) the load-settlement behavior of the piles under severe cyclic loading conditions. Since the treatment of complex aspects of pile foundation behavior is not codified in any guiding documents, several project-specific methods were developed for design and analysis of the foundation piles.

Jan 1, 2002

By Steve Kral

The mining industry is no stranger to hard times. Throughout its history, the industry has faced the ups and downs of commodity prices, difficult-to-mine-and-process ore bodies, labor issues and other problems. Throughout it all, though, the mining industry continues to provide the materials needed for society —even in the face of attacks by those who seek to cripple the industry or have it go away. The reason the mining industry survives, of course, is that mankind requires the products the industry produces. And, in recent decades, the industry has developed new technologies and improved on existing ones to produce those products in environmentally sound ways. At the same time, the economic benefits have been enormous to communities throughout the world where mining takes place.

Jan 1, 2002

Several years ago, Hudco Industrial Products began experimenting with the idea of levitating a conveyor belt with a film of air, much like the puck on an air-hockey table. While conducting its research, the company found out that some Russian and Dutch companies attempted the concept during the 1970s. After studying those conveyors, Hudco determined that its design was better. The Hudco advanced air-supported conveyor consists of an air-tight plenum, or chamber, that runs the length of the belt. The topside of the plenum has a formed trough. It corresponds to the profile of conventional troughing rollers. Low-pressure air is provided to the sealed plenum from a low horsepower blower. This pressurized air is metered and released through the central portion of the trough and reacts against the underside of the belt. The differential pressure between the top and bottom surfaces creates the lift to support the loaded belt. Airtight covers are installed to seal the transported materials in the plenum trough.

Jan 1, 2002

By Hodjat] [Shiri

A 4-legged jacket structure was installed by an Offshore Installation Contractor (OIC) in the Persian Gulf. In addition to four open-end pipe piles, six conductors were installed by OIC. During the installation of the piles and conductors, some cemented layers were encountered, which had not been accounted for in the foundation design performed by an independent well known offshore geotechnical site investigation contractor (OGSIC). Six months later, the Drilling Company (DC) hired by Client to execute the wells, reported that all of the six conductors were presenting anomalies, such as vertical misalignments up to 10o and/or collapse of the conductors tip and mid height. The DC faced with serious problem in drilling of the wells and in spite of several times milling the conductors and spending 40 days unpredicted extra time, some of the routes could not be opened and Client lost millions of dollars due to direct and indirect associated costs and expenses. This paper presents a complete overview of all engineering, construction and specially geotechnical investigations and shows that how an inaccuracy in interpretations of the results of an offshore geotechnical site investigation as the main reason in this case study can cause serious damages to whole project with unbelievable time and cost impacts some times up to millions of dollars.

Jan 1, 2006

By Terry W. Mellors, Robert J. F. Goodfellow

The underground industry has been forced to reconsider risk management sincethe introduction and implementation of the “Joint Code of Practice for Risk Management of Underground Works in the UK” published in 2003 and the subsequent international version published by the ‘International Tunneling Insurance Group’ (ITIG) in January 2006.What does this mean for major tunnel projects in the US and elsewhere? The discussion will highlight the implementation of the Codes to date, risk management principles embodied in the Codes and the use of risk registers as a projectmanagement tool and the management of risk.

Jan 1, 2007

By Kent von Maubeuge, Charles R. Landis

The global bentonite industry is a dynamic market balancing a range of end uses with an ever growing number of bentonite producers. In addition, markets in developed countries are elevating the level of detail and transparency for materials reporting in programs, such as the Registration, Evaluation, Authorization and restrictions of Chemicals (REACH) program in the European Union. Bentonite is impacted by programs of this nature. The majority of the bentonite products sold around the world are sodium bentonites. These sodium bentonites consist either of natural sodium bentonites, or naturally occurring bentonite dominated by divalent interlayer cations (Ca+2 andMg+2) subsequently exchanged with sodium cation. The latter variety is often called “sodium-activated“, or “soda-ash treated” bentonite. Once exchanged with sodium, these bentonites are often difficult to distinguish from natural sodium bentonites using common commercial testing protocols. Due to their similar colloidal and bulk chemical properties; the lack of test procedures designed specifically to identify this product feature; and the failure to completely or effectively explain their differences, sodium-activated bentonite is often considered to be identical to natural sodium bentonite in the industry. This article defines both general types of sodium bentonite and presents a technique that could serve the industry as a tool to confirm the variety of sodium bentonite in question. Specifically, geochemical properties such as carbon (C13/C12) and oxygen (O18/O16) isotopic ratios can distinguish activated, even slightly activated bentonites, from bentonites not introduced to additional sodium during manufacture.

Jan 1, 2004

By Klaus Pöllath

This paper describes mitigating measures and the design of compensation grouting which will be executed from deep shafts of the Amsterdam North/South Metro line project. Due to the specific conditions for TBM-tunnelling in Amsterdam (historical buildings on pile foundations near the tunnel and soft soils with high groundwater levels) tunnel construction necessitates mitigating measures, such as compensation grouting or soil freezing. Züblin developed a special shaft construction method for critical distances to buildings. For the compensation grouting Züblin developed a new software tool, called SOFIA, which controls and visualizes and thus optimizes the entire injection process. This tool significantly increases the efficiency of the injection works while reducing the geotechnical risks.

Jan 1, 2006

By R. Abela

In over ninety per cent of mineral sand plants, the most commonly used equipment is the spiral concentrator. The tonnage treated over typical spiral plants can range from as low as 200 ton per hour up to 6 000 tons per hour. Due to the limited capacity of each spiral, plants consist of multiple spirals assembled into banks. The mixture of minerals present in the sand feed requires several spiral stages to achieve the desired mineral recovery. Due to the complexity of the spiral circuits, there are always some design and operating problems that present themselves in plants. These range from slurry distribution, spirals operating at incorrect design parameters and feed variations. The material being treated is difficult to maintain in suspension due to its high density, resulting in segregation and preferential flow in pipelines, distributors and sumps. The objective of this paper is to highlight common problems associated with spiral installations to designers and operators of plants. Practical solutions are recommended in order to prevent and minimize these mistakes in the design. These solutions may be used to improve performance on operating plants.

Jan 1, 2003

By Satish Kate

Indian limestone mines which are highly mechanized in operation and supply limestone to the cement plants have been quite successful in devising ways and means to optimize blasting parameters, so as to have best fragmentation, powder factor, and cost of excavation. In primary blasting mechanized or manually mixed ammonium nitrate Fuel Oil is quite popular in dry holes, and in case of watery holes conventional packaged slurry/emulsions are being used. In order to avail the low density characteristics of the ANFO, some limestone mines have also used Saw Dust and Rice Husk along with ANFO. A number of field trials have been undertaken to explore the suitability of mixing rice-husk and saw dust with ANFO. Presently, about 10% of rice husk/saw dust is being used only to expand the explosive column. The main technical consideration for the use of saw dust/rice husk, has been to reduce the final density and increase the occupancy of explosive in the blast-hole. This not only lowers the detonation pressure in the blast holes, but also reduces cost of explosive without compromising on the fragmentation quality. Besides, with sleeping of the charge there is no substantial fall in the blast quality.

Jan 1, 2006

By T. J. Batchler

Deformable materials are sometimes added to ventilation stopping constructions to prevent damage caused by convergence in coal mines. However, adding deformable materials can significantly reduce the capacity of a stopping to resist transverse loading. As part of its mining health and safety program, the National Institute for Occupational Safety and Health (NIOSH) has conducted research on the effect of various materials with different deformation properties on the transverse loading capability of a stopping wall. Based on a three-point hinge method of failure, a half-wall method of testing in the NIOSH Mine Roof Simulator was used to simulate full-scale wall behavior. This simulated the fracture initiation and eventual failure of the stoppings from transverse loading. The impact of the modulus of elasticity of various deformable materials was examined in this study. A polystyrene foam block with a low modulus of elasticity, which is commonly used as a deformable material, was shown to degrade the transverse load capacity of the stopping by as much 95%. Other materials with higher modulus of elasticity preserved more of the transverse load capacity of the stopping, but were not able to absorb as much convergence. This paper presents the results of a parametric study that quantifies the impact of various deformable materials in block stopping construction under transverse load conditions. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009