Search Documents

By George Watson, Gu Quanzhong, S. Gerard Sawyer

Bulkheads, also known as hydraulic seals, are used to seal abandoned workings and protect adjacent active mines from explosion and control unwanted inflows of water from poorly sealed shafts, water-bearing strata, and abandoned mine areas or gobs (1). At coal seam outcrops, bulkheads have typically been used to prevent access and to control acid mine drainage. Bulkheads have also been installed at outcrop openings located within the footprint of an embankment dam, or within the reservoir of an impoundment, to prevent stored water or slurry waste from flowing into active or inactive underground mine workings (2). Components of MICON Bulkhead Seal MICON bulkhead seals in mining applications refer to seals designed to impound liquids or slurry. The MICON bulkhead seal is comprised of two concrete block walls set in the front and back and a polyurethane/aggregate core (Figure 1). The two walls are usually dry-stacked, surface-bonded walls constructed with solid load-bearing concrete blocks (ASTM C90) or concrete building brick (ASTM C55). The surface bonding material used in the wall construction must be MSHA-approved. The type of stone, if any, used to fill the space between the walls is not essential. However, MICON generally uses No. 57 limestone in 50 lb. bags, specified to moisture control, shrink-wrapped and palletized. The polyurethane foam used in the construction of the bulkhead seal is engineering specified and formulated by density based on the optimization of cost, seal core thickness, required adhesive strength, the use of stone filler and other required physical properties.

Jan 1, 2005

By Bradford F. Townsend

A study was made on six collapses that occurred during large-diameter tunnelling through weak sedimentary rocks and soil using SES methods in three stages?top heading, bench and invert. The collapsed lengths are between 20 m and 277 m. The collapses were re-mined using essentially the same tunnel-ling method with larger excavation profiles to accommodate the designed remedial measures consisting of ground treatment, pre-support and stronger initial support/outer lining required to carry higher ground loads acting in the collapsed lengths. The paper presents information on the collapses and the design and execution of the remedial measures.

Jan 1, 2008

By S. Escoffier, A. Giraud, K. Su, F. Homand, N. Hoteit

Abstract For the feasibility study of an underground waste disposal the characterization of the coupled behaviour of the host rock is required: Because of the very low permeability of these formations few experimental data are generally available. In this framework the uses of the sensitivity studies could orient the experimental efforts by highlighting the key parameters of the formation. This paper gives a first approach of the sensitivity studies performed with probabilistic methods in the geomechanical field. A one dimensional model which characterizes the thermohydromechanical response of an argillaceous rock to the excavation of a waste canister site and its setting up, is considered. Zusammenfassun Die Machbarkeitsstudie eines tiefliegenden Endlagers für radioaktive Abfälle beinhaltet die Untersuchung des gekoppelten Verhaltens des im Lagerbereich anstehenden Gesteins. Aufgrund der sehr geringen Wasserdurchlässigkeit dieser Formationen liegen häufig nur wenige experimentelle Angaben vor. Die Verwendung von Sensibilitätsstudien kann in diesem Zusammenhang als Hilfsmittel zur Entscheidungsfindung dienen. Dabei sollen die maßgeblichen Eigenschaften der Formation festgestellt werden, anhand derer der Umfang der experimentellen Erkundung festgelegt werden kann. Dieser Artikel stellt einen ersten Ansatz zur Durchführung von Sensibilitätsstudien mittels einer mechanisch-probablistischen Kopplung im Bereich der Geomechanik sowie die Vorteile gegenüber Parameterstudien vor. Zur Abbildung des thermohydromechanischen Stoffverhaltens von tonigem Fels während der Schachterstellung und der Einlagerung der Abfälle wird ein eindimensionales Model verwendet. Résumé L'étude de faisabilité d'un centre de stockage de déchets radioactifs en profondeur passe par la caractérisation du comportement couplé de la roche hôte. Du fait de la très faible perméabilité de ces formations, souvent peu de données expérimentales sont disponibles. Dans ce cadre l'utilisation d'études de sensibilité permettrait d'orienter les efforts expérimentaux en faisant ressortir les caractéristiques primordiales de la formation. Cet article présente une première approche de la réalisation d'études de sensibilités à l'aide de couplages mécano-fiabilistes dans le domaine de la géomécanique. Un model unidimensionnel caractérisant la réponse thermohydromécanique d'une roche argileuse au creusement d'un puit de stockage et à la mise en place de conteneurs de déchets est considéré.

Jan 1, 2003

By Rafael C. Castro, Geoffrey Hughes, Fredrick (Rick) Vincent, Philip H. Albert

Seven pairs of drop and ventilation shafts, between two and nine feet in diameter, will convey combined sewer flow to a 230-foot-deep, 26-foot diameter storage tunnel. This paper will present case histories for each site. Discussion will include functional requirements, program and site access constraints, structural design, geology, the variety of excavation and lining construction methods used, and lessons learned. Noteworthy observations include the importance of assuring competent ground sup-port at the soil-bedrock interface and of achieving tight verticality tolerance using both top-down and raise bore excavation methods.

Jan 1, 2007

By Susan L. Bednarz

Recent advances in digital cameras and image processing allow photographers to produce excellent high-resolution action shots in low light and high contrast conditions commonly encountered underground. Digital photography is often used for construction and inspection documentation for underground structures. Designers, owners, and contractors benefit from quality photographs that document incremental progress and project milestones. Documentation photos serve as a lasting record of as-built conditions, are an important marketing tool, and help the owner build public support for expensive public works projects. When the project is complete, the only mementos that the participants will hold onto are the photographs.

Jan 1, 2008

By R. Peroni, J. Kopp

Mine planning and scheduling is based on using a geological model for the deposit. Blocks are used to discretize the deposit into mineable volumes where grade values are assigned. Traditional estimation techniques such as kriging or inverse distance weighting are frequently used for this task where an interpolated value is calculated within a discrete volume. This group of block grades is the input for sequence optimizers, which base their decision on the economical value of a given block. Ultimately, the economical value of a block depends on its grade, making mine sequencing sensitive to all estimated values. If one looks to a block not as a single grade but as a set of equally possible grades, its economical value will change as different grades can be assigned to it. Stochastic simulation is known to provide the tools to assess grade variability, which makes it possible to generate equally probable values in a block. Different grade block models can thus be built and multiple sequencing alternatives are observed by running the optimizer for these distinct inputs. The results demonstrate that the methodology is adequate for risk assessment and proves to be useful for mining project sensitivity analyses. Differences in the project net present value showed that there is little difference between the two simulation methodologies (sequential Gaussian simulation and sequential indicator simulation) applied. The process is demonstrated using a Brazilian kaolin deposit. Keywords: geostatistical simulation, mine planning, sequencing, risk assessment, open pit optimization.

Jan 1, 2003

By Ashutosh S. Dhar

Cast-in-place piles were examined in this paper from the viewpoints of construction quality, axial capacity, and load-displacement responses. The results of ten 450 mm diameter (18? f) bored piles, installed in a soil deposit of silt to medium dense sand using the method of percussion drilling, were tested under static loads. The results of the pile load tests were used for evaluation of various design methods of calculating pile capacity. The study revealed that the design methods based on the concept of critical depth underestimated the ultimate skin fiction. Thus, the applicability of the critical depth concept for design of bored piles under the soil condition considered may be unreliable. The estimated skin friction factor, ß, was too low in these methods. The Tomlinson method and the Neely method provided the best prediction of the ultimate skin friction. The methods used for calculating end bearing resistance were found to provide a conservative estimate of the resistance. During pile load tests, a settlement of 5 to 6 mm was required for full mobilization of skin friction for the piles in loose sand, while larger settlements (> 10 mm) were required for piles in denser soil. The ultimate skin frictional resistance was observed to be low for piles in loose sand.

Jan 1, 2006

By N. Kumar, A. K. Dhawan, A. Varughese, S. K. Khullar

Abstract The in-situ stress field is one of the primary parameters influencing the performance of underground structures particularly in the Himalayas where there is strong influence of topography and geology on in-situ stresses. It is always advisable to measure the in-situ stresses, in whatever best way possible. Hydrofracturing is one of the methods by which in-situ stress can be measured. This paper briefly describes details of the concept of Hydrofracturing in arriving at the in-situ stresses of the rock mass at Pancheswar Project. The data obtained from the tests has been analysed, interpreted and the results are presented in this paper. Kurzfassung Das Spannungsfeld an Ort und Stelle ist einer der wichtigsten Parameter, die das Verhalten der Untergrund-Struktur beeinflussen, insbesondere in den Himalayas, wo die Topografie und die Geologie einen grossen Einfluss auf die oertlichen Spannungen ausueben. Es empfiehlt sich stets die Spannungen an Ort und Stelle so gut wie moeglich zu erfassen. Die Hydrofraktur bzw hydrografisches Zerstueckeln ist eine der Methoden, die bei den Messungen der oertlichen Spannungen verwendet werden koennen. Diese Abhandlung beschreibt kurz Einzelheiten ueber das Konzept von Hydrofraktur bei der Bestimmung der Spannungen an Ort und Stelle von der Felsmasse bezueglich des Projekts Pancheshwar. Die gewonnenen Daten aus den Messungen wurden analysieret und ausgewertet. Die Ergebnisse werden dabei vorgelegt. Sommaire Le champ de contraintes in-situ est un des paramèters principaux influencant l’exécution des structures souterraines particulierèment en Himalaya où les forces in-situ sont fortement influencées par les caractéristiques topographiques et géologiques de la région. La fracturation hydraulique est une technique qui permet de mesurer des forces in-situ des massifs rocheux. Cet article décrit brièvement le mécanisme de fracturation hydraulique et présente les résultats de mesure des forces in-situ des roches au site du projet hydroélectrique de Pancheswar.

Jan 1, 2003

By Ronald E. Heuer

A 1995 RETC paper of similar title presented a method for estimating rock tunnel water inflow based on semi-empirical correlations with borehole water pressure tests. Since that time the author has found the method to be very useful, and it has been used by others in the industry. This current paper is an update which is intended to: A. More clearly explain assumptions and limitations of the method. B. Describe some case history examples. C. Respond to questions which have been raised; and extend the method to other considerations including distribution of inflow along the tunnel, panning requirements, interpretation of tunnel probe hole water inflow, and estimation of potential effectiveness of pre-excavation grouting to reduce water inflow.

Jan 1, 2005

Effects of DA as a Grinding Aid on Selective Grinding of Low-Grade Bauxite Effects of DA (a copolymer of acrylic acid and acrylamide) as a grinding aid on selective grinding of low-grade bauxite were investigated in this study. The addition of DA into the grinding system enhanced the selectivity of grinding and increased the A/S ratio in the coarse fraction of ground product, leading to improved throughput of grinding mills and alumina recovery. The results showed that DA decreased the viscosity of slurry significantly and hence improved grinding efficiency due to low viscosity at a high slurry concentration. Both the hydrogen bond formation and chemical adsorption existed between DA and the surface of bauxite particles. The adsorption of DA on the surface of bauxite could decrease stress needed for crack initiation and extending during grinding, prevent new-born crack surfaces from rejoining, and promote the expansion of the cracks.

Sep 13, 2010

By Andreas Prucker

The Greater Vancouver Water District (GVWD) is currently constructing the largest water treatment plant in Canada. As part of this treatment scheme twin water transfer tunnels are being constructed. Work commenced with the 11 m diameter, 185 m deep Seymour Shaft which was excavated by drill and blast using a mobile crane for hoisting. The Seymour Shaft is the first large diameter shaft that has been sunk in Western Canada in recent years. The operational aspects associated with the hoisting, the drill-blast-support cycle and water control in the shaft are the focus of this paper.

Jan 1, 2008

Triboelectric Separation - Beneficiation of Coal The performance of triboelectric separators is highly sensitive to the selectivity of the particle charging process. This paper presents a quantitative study on triboelectric coal beneficiation. The performance of different charging media was studied. Stainless steel was identified as having a work function between that of coal and silicate gangue and found to be the optimum charging medium for coal beneficiation. Recent results from separation tests were performed where silicate gangue was separated from crude coal using a parallel plate free-fall separator are illustrated.

Sep 13, 2010

By Glen Frank, David R. Chapman

Determining the number of boulders and cobbles that will be encountered in the tunnel envelope is one of the most difficult problems confronting the geotechnical engineer in the design of tunnels in glacial terrain. This issue is very important to the contractor, both in determining what methods will be used to construct the facilities and the advance rate that can be achieved for the chosen construction methods. The cost of constructing tunnels by pressurized face tunneling techniques is very sensitive to accurate characterization of the very coarse fraction (large cobble and boulder sized clasts), and no standard method is current available for characterizing boulders and cobbles. Careful use of large diameter borings and the sampling and analytical techniques outlined in this paper can provide a means to answer this difficult question. By performing large diameter borings and carefully recording and sampling the cobbles and boulders encountered, an estimate for the amount of these materials present in the formations sampled can be provided. Using this method allows the designer to communicate the expected geologic conditions to the prospective bidders in a manner that is both definitive and defensible. This paper describes the method as it was used in conjunction with the design of a large diameter sewer tunnel in the Columbus, Ohio area.

Jan 1, 2005

By Russel Delmar, Rick Everdell, Harry Charalambu, John Tait

Award of the Design/Build Agreement for construction of Ontario Power Generation’s (OPG’s) Niagara Tunnel Project was made after an intensive 8-month international procurement process. The 14.4-m diameter × 10.4-km long rock tunnel will divert 500 m3/s of water from the Niagara River to the Sir Adam Beck hydroelectric generating complex. The procurement process and Design/Build Agreement included features to address the owner’s requirements regarding risk allocation and cost and schedule certainty, while encouraging innovative ideas from the industry, both technically and commercially. The process included an international expression of interest and prequalification, followed by an invitation for design/build proposals to qualified proponents, and comprehensive proposal evaluations and negotiations with several respondent proponents. An honorarium was provided to the unsuccessful participants in the proposal stage. The resultant negotiated Design/Build Agreement includes Owner’s Mandatory Requirements, negotiated contract terms and conditions, performanceincentive bonuses and liquidated damages for schedule and water delivery performance, a multistaged Geotechnical Baseline Report, joint risk management, references to preexisting community impact agreements and measures to reduce impact on tourism. It also addresses regulatory approvals and permits, an owner controlled insurance policy that required reference to the International Tunneling Insurance Group (ITIG) Code of Practice for Risk Management as a condition of coverage, site specific safety, security and environmental plans, formal team building, a dispute review board, and escrow documentation.

Jan 1, 2007

By Alex Naudts

Pre-excavation grouting is a predictable and reliable technique performed to prevent or minimize settlement in advance of, or during the tunneling operation. It safeguards the infrastructure above the tunnel alignment. Cement based suspension grouts and sodium silicate based grouts are frequently injected to consolidate and strengthen the formation and create a reinforced canopy above the tunnel trajectory. Grouting is typically performed through permeation and permeation in conjunction with hydrofracturing. Multiple injection passes through steel sleeve pipes are ideal, since they create an effective forespiling system to facilitate tunneling without causing unacceptable settlement, even with minimal overburden thickness. Ten pre-excavation grouting projects performed in the North America are discussed in this paper.

Jan 1, 2008

By D. Grgic, A. Giraud, F. Homand

RESUME : Le comportement mécanique partiellement saturé du minerai de fer a été étudié à partir d’essais de compression simple sur des éprouvettes à pression capillaire imposée par les solutions salines. Les échantillons restent peu saturés (32 %) même pour une humidité relative de 94 %, du fait de la présence de mésopores. Jusqu’à 90 % d’humidité relative la résistance diminue régulièrement. De 90 % à 94 % une forte chute est observée et pourrait être liée à la fois aux effets capillaires et à l’hydratation de certains minéraux. Le cycle hydrique subit par la roche dans la mine a été modélisé en 1D à l’aide d’un code de calcul entièrement couplé pour les milieux poreux partiellement saturés. Les calculs ont montré notamment une diminution importante en paroi des contraintes totales au cours de la phase de désaturation et une augmentation importante au cours de la phase de resaturation. Ces variations pourraient induire un endommagement du massif et être à l’origine d’instabilités, et soulignent l’intérêt d’une modélisation avec une géométrie plus adaptée. MOTS-CLEFS : mines de fer, partiellement saturé, pression capillaire, résistance, modélisation. ABSTRACT : The partially saturated mechanical behavior of iron ore has been studied from uniaxial compression tests on samples in which the suction is imposed with aqueous solutions. Samples are little saturated (32 %) even for a 94 % relative humidity because pores are too large. Up to 90 % relative humidity the strength decreases regularly. From 90 % to 94 % a great decrease is observed ; it could be explained by the capillary effects and the moisturizing of some minerals. The hydrous cycle imposed to the rocks in the mine has been modeled with an 1D fully coupled code for partially saturated porous media. The computations have shown an important decrease in the total stresses at the wall during the desaturation stage and an important increase during the re-saturation stage. These variations could induce a rock mass damage and instabilities, and highlight the necessity of a modeling with a well-adapted geometry. KEY-WORDS : iron mines, partially saturated, suction, strength, modeling. ZUSAMMENFASSUNG : Das mechanische Verhalten von teilweise gesättigten Eisenerz wird durch einachsige Druckversuche untergesucht. Die Prüfkörper haben einen durch Salzlösungen gestimmten kapillarischen Druck. Sie bleiben kaum gesättigt (32 %), sogar bei einer relativen Feuchtigkeit von 94 %, aufgrund der Anwesenheit von Mesoporen. Bis eine relative Feuchtigkeit von 90 % verringert sich gleichmässig die Druckfestigkeit und zwischen 90 % und 94 % merkt man eine starke Abnahme in Verbindung, möglicherweise, mit kapillarischen Effekten und Hydratation von bestimmten Mineralen. Die nümerische 1D Modellisierung des gezwungenen Wasserzyklus im Stein der Mine ist mit einem für porösen Medien ganz vernetzten Rechnungcode geführt. Sie zeigt besonders ein bedeutendes Sinken der Gesamtspannung während der Entwässerung und eine bedeutende Steigerung während der Sättigung. Diese Veränderungen könnten die Beschädigung des Gesteines herbeiführen und die Grundlage von Unstabilität sein. Sie unterstreichen die Wichtigkeit eine Modellisierung mit einer gut geeigneten Geometrie. STICHWÖRTER : Eisenminen, teilweise gesättigt, kapillarischer Druck, Druckfestigkeit, Modellisierung.

Jan 1, 2003

By James A. Schneider

Selection of resistance factors within Load and Resistance Factor Design (LRFD) requires accurate assessment of uncertainty and bias in load and resistance. To date, many studies have focused predominantly on the assessment of uncertainty, while the potential for bias appears to be the dominant factor in design for consistent levels of reliability under a variety of situations. Bias comes from factors which have been ignored in design method development but significantly influence resistance when extrapolating from conditions typical of databases to those at a given site. Uncertainty and bias can be quantified as the coefficient of variation and mean (or median) of a data set, respectively, for statistical assessment of load and resistance factors. This paper first presents an overview of statistical assessment of resistance factors, and then discusses factors that influence uncertainty and bias when extrapolating to situations outside of conventional databases of driven pile axial capacity.

Jan 1, 2009

The state of the tunneling and underground construction industry and the advancements of the industry?s biggest machines were the main topics at the 2008 edition of the UCA of SME?s annual George A. Fox Conference. This year SME hosted more than 250 tunneling and under-ground construction professionals at the Graduate Center, City University of New York. During the morning session of the long-running one-day conference, attendees heard a state of the industry through the annual Home-town Update where it was evident that the industry is doing well. Michael McHugh of Moretrench cruised through the many projects that are under way along the Eastern seaboard of the United States and said he could have gone longer if time allowed. An example of how well things are going for the industry is a look at New York, where the industry is flourishing. The New York City Water Tunnel # 3 project is a $668 million project that was awarded to Schiavone/Shea/Frontier Kemper joint venture in 2004. McHugh said that mining on the project was completed in August 2006 and that all con-tract work is expected to be completed by August 2009. The Second Ave. Subway is a $337-million twin tunnel project that will connect upper Manhattan with the financial district. This is a four-phase project. McHugh said the Metropolitan Transit Authority obtained full funding in 2007 and construction awards will be awarded during the next two years. The No. 7 Line Flushing extension, a five-year, $1.15- billion project that will redevelop the Hudson Yards area of Midtown West and the New York City Water Tunnel No. 3 project is the largest capital construction project in New York City?s history. McHugh said the project was given notice to proceed on Dec. 13, 2007. The project includes three large shafts, two parallel 6.7 m (22 ft) tunnels at 2,000 liner m (6,500 liner ft), one large cross adit, one large underground rock cavern station with two interlocks and eight penetrations. These were just a few of projects mentioned in the Hometown Projects update.

Jan 1, 2008

By S. G. Gendler

One of the ways of trauma and occupational diseases level reduction is noted to be the improvement of the labour protection measures planning. As an indicator for prospective trends determination in the labour protection planning improvement sphere economic risk has been proposed to be used. The trauma and occupational diseases analysis based on the correlative and regressive methods has been carried out for the “Vorgashorskaya” mine of Pechora coal basin. Trauma and occupational diseases occurrences frequency and economic losses value have been estimated. Trauma and occupational diseases economic risk distribution analysis has been presented in respect to the different subdivisions and occupational groups of “Vorgashorskaya” mine.

Jan 1, 2003

On the Kinetics and Equilibrium Models for Biosorption of Ni(II) onto a Gram-Positive Bacteria Strain, Rhodococcus opacus, for Environmental Applications The aim of this fundamental study was to evaluate the biosorption of Ni(II) from aqueous solution streams onto a Rhodococcus opacus strain through kinetics and equilibrium isotherms studies. The biosorption of nickel achieved its highest value in a pH around 5. The experimental data evaluation was carried out focusing three two-parameter models, as: Langmuir, Freundlich, Dubinin - Radushkevich. In order to determine the best isotherm fit, three error analysis methods were used to assess the data: correlation coefficient (R2), residual root mean square error (RMSE) and Chi-square test. The error analysis established that the Freundlich model fits better the nickel biosorption data. Maximum uptake capacity of nickel reached a value around 7.63 mg.g-1 for R. opacus. The biosorption rate was fast and achieved a removal of around 79 per cent of Ni(II) in the first 5 minutes at room temperature (25 ¦ 2¦C). The experimental kinetics data was evaluated considering two models (pseudo-second order and pseudo-first order). The error analysis established that the pseudo-second order model better fits the data.

Sep 13, 2010