Search Documents

By Jeffrey A. Shibe

A prototype Fire Safety Evaluation System has been developed and is ready to be evaluated by a Peer Consulting Panel and for performing field tests. The system can be used to determine combinations of widely accepted fire safety equipment and under-ground coal mine features that provide a level of safety equivalent to those required by the Code of Federal Regulations-Title 30 for underground coal mines. In this evaluation, equivalent safety performance is gauged in terms of overall level of safety provided rather than by a component by component comparison.

Jan 1, 1987

Removal of Thiocyanate from Solutions by Precipitation

Sep 13, 2010

Support design in jointed or blocky rock masses is often approached by the use of either 'rules of thumb', rock mass classification systems such as the Q-system (Barton, Lien and Lunde, 1974) or RMR (Bieniawski, 1973) or conventional wedge analysis. Generally, this requires that a number of key simplifying assumptions are made and the support system is designed to cater for either a mean, most likely, or worst case scenario depending on the risk tolerance. The design block size is often a major uncertainty and often a worst case block size based on excavation span is used. Thompson and Windsor (2007) state that it is inappropriate to base support designs on the excavation size as these size blocks rarely occur if discontinuity trace lengths are considered. Probabilistic keyblock methods can be used to determine the most likely design block sizes. A methodology is presented whereby JBlock software (Estherhuizen, 1996) is used to estimate potential block sizes as part of the support design process. Using information such as the spacing, orientation and length of discontinuities, it is possible to simulate blocks in the walls of an excavation (Esterhuizen and Streuders, 1998). Keyblock analysis methods (Goodman and Shi, 1985) are used to evaluate whether blocks are removable and whether the chosen support will be sufficient to ensure stability. Data from two mines is used to demonstrate how probabilistic keyblock analyses can be used in support design. Discontinuity data was used to generate 10 000 removable blocks and the design block size statistics were determined. For one mine this information was used to scale blocks in a conventional. Unwedge analysis whilst for the other mine, the point estimate method (Harr, 1987) was applied. The choice of appropriate design acceptance criteria in terms of factor of safety and probability of failure is also considered.

Nov 25, 2010

Lead Removal from Contaminated Soils with Chelating Agents

Sep 13, 2010

By M E. Pierce, T V. Garza-Cruz

Rock mass strength and brittleness generally have a significant impact on both cavability and fragmentation. Variability in these properties across a panel or block footprint is of particular interest because stronger units have the potential to significantly impact cave shape. This paper describes how FLAC3D™ was used to examine the impact of variability in rock mass properties on predicted cave performance to aid in assessing potential risks associated with the proposed design.A case study orebody was subdivided into a number of domains to reflect the heterogeneity of the rock mass at the scale of a proposed inclined cave. The results suggest that the presence of stronger units has the potential to impact cave shape significantly in the southern half of the cave footprint and could increase the potential for cave stalling at shallow depths. If this unit is stronger and less brittle than expected, an overhang is predicted to develop in the southern half of the inclined cave at depth. The effective hydraulic radius is significantly reduced due to the overhang in the south, and the cave could eventually stall at shallower depths in the north.CITATION:Garza-Cruz, T V and Pierce, M E, 2016. Impact of rock mass strength variability on caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 359–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Mark K. Larson

Panel-scale modeling of stress changes induced by longwall coal mining is a challenging problem, particularly in deep mines of the western United States. Two common approaches to this problem are the empirical and boundary element modeling methods. One boundary element method, LaModel, was recently calibrated to field measurements at a mine in Colorado (Larson and Whyatt, 2012). However, the calibrated overburden properties were extreme, resulting in very low estimates of gob loading. Next, the empirical method was calibrated to field measurements and applied to the problem, but this approach clearly extrapolated this method well beyond the characteristics of underlying cases. This paper examines a third option, the elastic continuum boundary element program Mulsim. The program was expanded to handle LaModel-size meshes in a version dubbed Mulsim/ Large. Properties for the elastic, homogeneous overburden model in Mulsim were estimated as a thickness-weighted average of typical published elastic properties for each major stratum. These properties, along with a commonly used pillar strength equation and coal properties, produced the measured load transfer distance and reasonable gob loading without further calibration. Given the number of input parameters required for all of these methods, it is not surprising that LaModel and the empirical approach could be adjusted further to incorporate similar gob loads. However, these extraordinary measures failed to bring gate road pillar loading in line with Mulsim results. Differences in pillar load estimates continued to be significant (as large as 65% in this study). These results demonstrate that, for this particular case, the choice of analysis method impacts results in ways that cannot be removed by calibration of input parameters. Finally, the natural fit between the Mulsim model and mine conditions suggests that approximating overburden at the particular site used for this research as an elastic continuum is superior to the alternatives examined.

Jan 1, 2013

By Alejandro Ferrada Vergara

Most blasting techniques that are designed to improve fragmentation and subsequently improve ore work index to downstream comminution processes, apply powder or energy factor increases, either by stretching the drilling pattern (burden/spacing ratio) implementing faster initiation sequences or using more energetic explosives. The new application will move detonation parameters up, making the blasting process riskier for the surrounding boreholes, explosive column or initiation systems functioning.

Jan 1, 2016

By Jeremy Bosman, Johan de Korte

Traditionally the feed to coal preparation plants was de-slimed at 0,5 mm. The +0,5 mm size fraction was processed via dense-medium cyclones and the -0,5 mm size fraction was beneficiated with froth flotation, water-only cyclones or spirals. With the introduction of large diameter cyclones, the aperture sizes of de-sliming screens have progressively increased to about 3 mm in the belief that the larger cyclones are not able to effectively beneficiate coal which has a particle size below the ?breakaway? size. The efficiency of separation in the large dense-medium cyclones is improved by presenting a coarser feed to the units. At the same time, the capacity of the de-sliming screens is increased due to the larger screen apertures and in effect, the throughput capacity of the dense-medium section is increased. The 3 x 0,5 mm size fraction, which was previously processed in the dense-medium cyclones, is now added to the fine coal size fraction and processed by water-only methods such as Teetered Bed Separators (TBS) and spirals. Whether this practice is the most economical way to process the 3 x 0,5 mm size fraction requires further thought since the best processing route for the 3 x 0,5 mm size fraction will depend on a number of factors, amongst which are: o The washability of the coal and the amount of near-density material o Processing efficiency o Specification of the required product o The price paid by the customer for the product o The cost of processing the coal Breakaway size The ?breakaway? size is defined as the particle size below which the Epm of the smaller particles starts to decrease significantly. Bosman1 provides an approximate breakaway size versus cyclone diameter (Figure 1). It should be kept in mind though that the Epm of the small particles is a function not only of the cyclone diameter but also of feed pressure, medium density, medium viscosity, particle shape and density, top-size of particles in the feed, etc.

Jan 1, 2006

By Gino Merello

Dado que los cargadores frontales LHD son los equipos encargados de extraer gran parte de la producción en la mina subterránea El Teniente, se justifica el estudio de confiabilidad, mantenibilidad y disponibilidad que permita optimizar la actual estrategía de mantenimiento. En ese sentido, el presente texto señala la optimización de la estrategia de mantenimiento a través de la metodología de revisar continuamente los parámetros básicos del motor diesel y la condición físico-química del lubricante de motor. También se monitoreó con una frecuencia de dos días el estado general de los equipos, con el fin de detectar prematuramente algún tipo de daño que se derive de la implementación de la nueva estrategia.

Jun 1, 2014

By M. Askari, A. Ahmadi

"This study was conducted to establish the possible application of bioleaching in the pilot scale to recover valuable metals from the sulfidic tailings of Golgohar Iron Mine (Kerman, Iran). Using bioleaching processes, solvent extraction and sulfide precipitation recovery of valuable metals including, copper, cobalt and nickel from the tailing was investigated. The results showed that the optimum pH and temperature conditions relative to the bioleaching step was 1.5 and 45°C. The extraction of the metals from the low grade polymetal resource with complex mineralogy is very important from economic, environmental and technical point of views. Moreover, the proposed method has some advantages from energy saving, tailing management and creating added value from waste materials aspects.INTRODUCTION The growing demand for base metals and strategic such as: copper, nickel and cobalt as well as high-grade resource depletion has caused them, the mining industry to extract metals from low-grade resources and driven by complex mineralogy (Xie et al., 2005). Economic extraction of metals with low grade sources requires low-cost and efficient processing methods. A source with enormous potential for metals in future, secondary sources, such as: tailings mineral industries which the lack of appropriate technology and the high cost of processing weren't recoverable with previous procedures in the past. But it is possible that with develop new and efficient technologies have the economic exploitation ability. Recovery of metals from tailings resources is very important not only in terms of precious metals but also in terms of reducing environmental problems (due to heavy metals). The metals of copper, nickel and cobalt are mainly like sulfide compounds in the nature, usually for their recovery, first they make ore with flotation method to obtain the sulfide concentrate that containing valuable metals. then for the metal production, it will be melt and purification. Due to the environmental aspects, technical problems in the recovery of base metals from low grade ore and mixes, the presence of small reserves, in the past three decades they pay much attention to the use of hydrometallurgical processes for the recovery of base metals from these resources. These processes are classified according to the solver agent to leaching sulfates, chlorides, nitrates and amines (Hackl, 1995). Early, chloride leaching under oxidation condition in acidic or alkaline solutions was recognized the best process to produce sulfide concentrates. But then the basic processes sulfates was considered as the superior process because of being easier, a better understanding of the chemistry of leaching and recovery of base metals, especially copper from the environment easier sulfate solution with an organic solvent extraction and electro winning. The bioleaching is shown its ability on a commercial scale of low-grade sulfide minerals and ore that because of environmental reasons, the possibility of melting is not possible to them. The existing industrial base factories are based on primarily on the bioleaching and pressure leaching and recovery of cathode copper sulfate solution by extraction with organic solvents (SX) and electrowinning (EW) (Wang, 2005). Preliminary analysis has shown that valuable elements such as copper, nickel and cobalt are in the float flotation unit. Hence the plan to extract these metals from the wet tailing stream has been done."

Jan 1, 2017

By Shenghui Guo, Ying Lei, Hao Niu, Huilong Luo, Jinhui Peng, Libo Zhang, Yu Li

"In this work, the combination of microwave drying (MWD) and heat pump drying (HPD) drying experiments were designed by response surface methodology (RSM) based on central composite design (CCD) using design expert software (Version 7.15), and the process parameters were optimized. The conditions given by software are: the MWD time is 4.6 or 4.4 min; the HPD time is 9.0 or 8.6 min; and the sample mass is 620 or 600 g. Under those conditions the moisture content is 1.0 10-2kg water/kg wet basis, and the effectiveness ratio is 0.70 kg water/kwh. The results of confirmatory experiments conducted under the optimized conditions show the combined drying have superiority of decrease of energy consumption and increase of handling capacity over the single MWD or HPD.1 IntroductionSilica sand is one of a silicate mineral with properties as hard, anti-friction and less reactive, commonly used as raw material for foundry and construction. The silica sand obtained from mineral dressing processes such as scrubbing, magnetic separation and flotation. Its moisture content is approximately 0.08~0.12 kg water/kg wet basis. The most common methods used for drying are solar drying and hot air drying. But these methods have some shortcomings: for example, the solar drying has longer process time due to low energy yield, [1] hot air drying has low-energy efficiency and a lengthy drying time. [2]Microwave is electromagnetic waves with frequency are 300MHz to 300GHz. The outstanding features of microwave heating are rapidity and selectivity. The water specific inductive capacity of 60~78 is much bigger than common materials, the moisture always quickly absorb electromagnetic wave and rapidly transfer to vapors. So, it can significant reduce the drying time. [3] Heat pumps (HPs) are devices for raising the temperature of low grade heat energy to a more useful level using a relatively small amount of high grade energy."

Jan 1, 2011

By V. Arslan

The primary advantage of using oxalic acid is in the formation during leaching of soluble complexes that are both photo-chemically and microbiologically degradable. In this study, chemical leaching and bioleaching methods were used for quartz sand. Using the ANOVA-Yates test technique, the effects of solids rate, temperature and oxalic acid rate were investigated using chemical leaching experiments. Solids rate and temperature were effective parameters on the chemical leaching. After the tests, the removal of Fe2O3 increased to 97.02%. Finally, the iron content decreased from 0.315% Fe2O3 to 0.0094% Fe2O3 in the leached quartz sand. The effect of pulp density was investigated on the bioleaching experiments. The bioleaching of iron oxides by Aspergillus niger resulted in removal of 47.70% of the total iron in the quartz sand, and suggested that this strain has not a good ability to remove iron impurities from quartz sand in comparison with chemical leaching. The iron content decreased from 0.315% Fe2O3 to 0.164% Fe2O3 in the bioleached quartz sand.

Jan 1, 2009

By Paul M. Tyler

The literature on radium is already voluminous, but mcuh of it is too technical to be intelligible to the average reader, and there is no single publication that covers certain economic features of the radium industry. As a result of the renewed interest in the possibilities of domestic carnotite deposits a number of requests have been made to the Bureau of Mines for information, more particularly with reference to the business aspects of the industry. In order to meet this apparent need, the present paper has been prepared from material available in the files of the bureau. The technical data are compiled from various sources and are believed to be reasonably dependable, but the attempt has been not so much to achieve meticulous scientific accuracy as to brim; together facts of industrial significance and popular interest. GENERAL DESCRIPTION Radium is a brilliant white metal that melts sharply at about 700°C. and volatilizes appreciably at that temperature. With an estimated specific gravity of nearly 6.0, it is more than twice as heavy as aluminum and 25 per cent lighter than irons. Although it has been isolated in its metallic state, it is not used in that form, partly because it tarnishes rapidly even in dry air (forming a nitride), partly because of the greater expense of reducing it to metal, and partly because of the difficulty of dealing with such minute quantities of material. It is used always in the form of its compounds, the most important of which from the vie point of utilization are the bromide, chloride, and sulphate.

Jan 1, 1930

By Michael Mancuso

This report summarizes the problems of topsail handling as related to present requirements of law and current equipment availability. The most prevalent topsoiling systems are reviewed along with a listing of advantages/disadvantages and best features of each system. Seven mining regions are included, along with an analysis of prevailing land use, types of soils and attendant physical, chemical am biological characteristics. There are several probable areas of future research "lined which can benefit mining, minimize the social impact of mined lands and speed the return of mined lands to more productive long-term use.

Jan 1, 1981

By H. F. Yancey

The investigations described in this bulletin are confined to a study of the washing characteristics of bituminous coals. The major part of the work was conducted by the Bureau of Mines in cooperation with the Engineering Experiment Station of the University of Illinois and the State of Illinois Geological Survey Division between 1918 and 1924, in accordance with the provisions of an agreement between these agencies. The washing characteristics of coals from many of the important coal-producing fields of the Eastern and Central States were examined. The coals of the Pacific Northwest States and Alaska have been studied separately by McMillan and Bird of the Northwest Experiment Station of the Bureau of Mines at Seattle in cooperation with the College of Mines of the University of Washington.2 OBJECT OF INVESTIGATION The object of the investigation of coal preparation by the Bureau of Mines has been to promote the production of better prepared coal and to facilitate the correct selection and design of coal-preparation plants by obtaining as complete information as possible regarding the washability of the various types of American coals and the treatment best suited to each. In addition, some attention has been given to the development of new methods of washing coal. The work naturally divides itself into three rather distinct steps: (1) Development of a systematic method of examining and testing a coal; (2) classification of the American coals on a basis of the occurrence of the impurities associated with the coal in the beds; (3) examination of one or more representative coals of each type.

Jan 1, 1929

By C Li, D O’Dea, R Moreno-Atanasio, T Honeyands

The behaviour of iron ore granules in the feeding process of sintering is significantly influenced by the material properties of the granulated mix. Therefore, the measurement of key material properties of the iron ore granulated mix is indispensable prior to the simulation of the sintering process based on the discrete element method (DEM). In this paper, three key property parameters of the iron ore granulated mix, apparent density, elastic modulus and rolling friction coefficient, were measured in laboratory-scale experiments. For different sintering processes, the moisture content of the granulated mix normally varies according to the specific requirements for granule size distribution and operating conditions. Therefore, understanding the effect of moisture content on the property parameters of iron ore granules is very helpful in accurately determining the property parameters for DEM simulation work. In this paper, six groups of iron ore granule samples with six levels of moisture contents were prepared through granulation and the trends in apparent density, elastic modulus and rolling friction coefficient with the increase of moisture content were plotted and analysed based on the measurement results. The results show that as moisture increases from 6.9 per cent to 9.1 per cent, the apparent density decreases from about 3000 to 2800 kg/m3. With moisture increasing within the same range, the elastic modulus first decreases from over 200 MPa to below 100 MPa and then reaches a relative constant value of about 40 MPa at higher moisture contents. Rolling friction coefficients are measured using two methods with both indicating a similar trend, with the rolling friction coefficient first decreasing and then rising as moisture increases from 6.9 per cent to 9.1 per cent. The relationship between µr and µ’r is assumed to be similar to that between static and dynamic friction coefficients.CITATION:Li, C, Moreno-Atanasio, R, O’Dea, D and Honeyands, T, 2017. Variation in property parameters of iron ore granulated mix with moisture content, in Proceedings Iron Ore 2017, pp 79–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By R Zhou, B J. Monaghan, S J Chew, R J. Longbottom, D J. Pinson, H Li, P Zulli, G Zhang, L Lu

Steelmakers are increasingly motivated to use iron ore resources with a wider range of grades and mineral types that were previously considered unsuitable or uneconomical for sintering. In this respect, specific issues, which now require further investigation and understanding, include the sintering of ore types with:- overall higher gangue content- elements that cause problems in the steel manufacturing operations- distinctive sintering performance compared with traditional hematite-rich iron ores. Laboratory-based investigations of the sintering performance and the behaviour of gangue impurities during sintering is an important step towards the successful utilisation of these resources in steelmaking.In terms of laboratory-based sintering investigations, there are two generally accepted experimental scales utilised prior to undertaking industrial-scale trials, which include: bench-scale tablet (compact) testing and pilot-scale pot testing. The former has the advantages of flexibility and more precise control of sintering conditions; but it is difficult to simulate the heterogeneity of a sinter bed. The latter, which is carried out in pots with diameters between 150–500 mm, simulate the commercial sintering process and conditions quite well, but is time-consuming and labour-intensive due to operational complexity. It is therefore desirable to establish a smaller scale pot testing facility that avoids the disadvantages of the normal sintering pot but can provide comparable information.To explore the feasibility of small-scale pot testing, a ‘millipot’ facility was established to examine the sintering performance of iron ores and other non-traditional ferrous materials. The millipot has a diameter of 53 mm and height of 400 mm. The facility has the capability to monitor the sintering temperature at a number of locations (axial, radial) within the sinter bed and to adjust the suction (‘windbox’) pressure. This paper describes the development of the millipot facility and operational procedures, together with initial tests undertaken in order to match its performance with industrial sintering performance.CITATION:Li, H, Zhou, R, Pinson, D J, Zulli, P, Lu, L, Longbottom, R J, Chew, S J, Monaghan, B J and Zhang, G, 2017. A millipot set-up for sintering investigation of iron ores, in Proceedings Iron Ore 2017, pp 85–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Tristan H. Jones

Beginning in 1987, miniature dataloggers approved by the Mine Safety and Health Administration (MSHA) were publicly available for sale. The principal among these was the model CR21XQM, manufactured by Campbell Scientific, Inc. These dataloggers had been tested and were deemed permissible by MSHA and thus could be installed in the return air of an underground coal mine. In 1996, production of all permissible Campbell Scientific dataloggers ceased due to lack of sales. Data collection with these dataloggers has been a staple of ground control research in the United States for decades, and, without them, or a replacement, the capability to monitor ground behavior is severely impacted. Since that time, any party requiring a permissible datalogger has needed to borrow one that was purchased during the production years. In order to fill this technology gap and ensure its own data-gathering capabilities, the National Institute for Occupational Safety and Health (NIOSH) has developed and refined its own miniature data acquisition system (MIDAS). On February 16, 2010, MSHA deemed the MIDAS to be permissible and approved it for use in the return air of an underground coal mine. The MIDAS is an intrinsically safe, 16- or 24-bit datalogger, compatible with a wide range of resistive, single-ended, and differential-type instrumentation. It contains enough data storage memory to operate for over a year with typical data rates and is efficient enough to do this on a single C-sized alkaline battery for that entire period. It is menu-driven and requires no programming knowledge to operate. It supports wireless or hardwired communication for datalogger setup and data download. This paper describes the design, field and laboratory testing, and capabilities of the MIDAS datalogger. While not as fully -functioned as the CR21XQM, it is the only new permissible datalogger available, and there is intent to make it available to the mining industry for purchase.

Jan 1, 2012

By K. Nong, H. F. Fuls

The quality of Pregnant Leach Solution (PLS) at Skorpion Zinc is of utmost importance for efficient operation of the Solvent Extraction (SX) Plant. Suspended solids in the PLS forms CRUD in the settlers, resulting in reduced zinc transfer capacity and increased impurity carry over to Electrowinning. The Ishigaki Fibre-Wakishimizu filter (fibre media rapid filtration equipment) has been identified as polishing filter that potentially could remove solids from the PLS of Skorpion Zinc. A pilot unit with 20m³/h capacity was tested on site over a period of 9 months under plant operating conditions in the refinery. The FW filter produces a clear filtrate, acceptable for the Solvent Extraction. Turbidity is improved by 72%. Gravimetric analysis indicates a 47% removal of solids. However, the gravimetric method is biased by a co-precipitation of saturated salts during the analysis. Filter media is blinded by the Skorpion Zinc PLS solution, as result of suspended solids and process chemistry. The media could not be regenerated to acceptable conditions. Further testwork to investigate the impact of process solution chemistry modification on blinding is undertaken. Based on the outcome of this investigation a final decision on the FW filter can be taken.

Jan 1, 2007

By S M. Iveson, K P. Galvin, D Kumar

Dry separation of iron ore fines and other heavy minerals has previously been achieved using one of two main approaches. The first is an inclined table with an upward airflow via small holes to help form an autogenous dense medium. The second is based on fluidised beds comprising a dense medium formed by fine particles suspended in an upward flow of air. In either case, vibration can be introduced. This paper describes recent findings using a novel system referred to as the Sink-Hole Fluidiser, which utilises elements of both these two former approaches. This device consists of a conventional gas-fluidised bed of fine medium with a 1 mm aperture mesh located at the surface. This mesh contains relatively large holes that act as sink-holes. The fluidised media flows upwards through the sink-holes and then falls back into the fluidised bed via the fine apertures in the mesh. The particles being separated, which are much larger than the fine media, pass over these sink-holes, where they either sink or float. The sink-holes offer a more precise balance of forces, applied on a single particle basis, resulting in robust density separation.Experiments have been performed using 2.0–4.0 mm tracer particles of density varying from 2.4 to 4.8 relative densities (RD) separated in a 200 mm diameter Sink-Hole Fluidiser with a single 13 mm diameter centrally-located sink-hole. In this preliminary semi-batch work, it was found that the Sink-Hole Fluidiser was able to achieve sharp separations (Ep as low as 0.20). This work underpins the development of a new continuous steady-state Sink-Hole Fluidiser, applicable to the dry separation of iron ore fines.CITATION:Kumar, D, Iveson, S M and Galvin, K P, 2017. A novel sink-hole fluidisation method for dry separation of iron ore fines, in Proceedings Iron Ore 2017, pp 221–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017