Search Documents

By William P. Shinn

It is almost exactly seven years since the last previous meeting of the Institute in this city. In a paper on " Pittsburgh, its Resources and Sorroundings," read at that meeting, I showed that Allegheny County had produced in 1878, " one-twelfth of all the pig-iron,.... two-ninths of all the rolled iron (except rails), over one-eighth of all the Bessemer and open-hearth steel, two-thirds of all the crucible blister and puddled steel, one-fourth of all the glass, one-eighth of all the coal, and one-sixth of all the pig-lead produced in the United States;" and the object of this paper is to show that, great as the record then was, it has been greatly surpassed since.* Population. In my former paper I expressed the opinion that the census of 1880 would show the population of Allegheny County to be in excess of 300,000. The census report made it 355,869. The following shows the growth of the county in population from 1790 to 1880: 1790,...........10,309 1800,........... 15,087 1810,...........25,317 1820,...........34,921 1830,...........50,552 1840.............81,235 1850............138,290 1860............178,881 1870,...........262,204 1880,...........355,869 This makes Allegheny County, in 1880, rank sixth in population of the counties of the United States, whereas in 1870 its rank was ninth. The population of Pittsburgh in 1880 was 156,359, being twelfth

Jan 1, 1886

By K. Narayan Prabhu, W. D. Griffiths

"Heat transfer during the unidirectional solidification of a cast iron alloy against cast iron chills was investigated using an inverse modelling approach. Chills of thickness 100 mm and 10 mm were used, to simulate gravity die cruiting conditions and the use of chills in sand moulds. In both cases transient heat transfer, measured by the interfacial heat flux and heat transfer coeffieient; declined from initially high values in the first few seconds of solidification, to values about an order of magnitude lower which persisted for the remainder of the experiments. In the case of the thin chill it became saturated with heat until it was no longer in a position to extract further heat from ·the casting. These results were interpreted by studying the resistance to heat transfer from the casting offered by the ·casting-chill interface and the chill itself for example, the thermal resistance of the casting-chill interface can be influenced by the deformation of their respective surfaces and their subsequent relationship.IntroductionDie casting cast iron offers several advantages such as energy savings, higher mould yield, and better surface quality over the sand casting process1 • The process is· environmentally' friendly because of the elimination of the sand. However the design and construction of metallic moulds is expensive and a faulty die design may result in a defective casting: A simulation based process design of die castings would enable die designers and solidification modellings to try better designs of dies on the computer and arrive at a cost effective solution more quickly. This has numerous benefits for the die caster, as he would be able to produce sound castings with very short lead times.The success of a solidification model to predict accurately the thermal history and the location of hot, spots inside a solidifying casting depends to a large extent on the heat transfer data prescribed at the metal/mould interface. Many measurements of the heat transfer coeffident (or the heat flux) between a solidifying aluminum alloy and a chill have shown that the heat transfer coefficient is a function of most of the variables of the casting process2 - 8. However heat transfer studies during the solidification of ferrous alloys are rather limited. The high temperatures involved suggest that the contribution due to radiation heat transfer cannot be neglected."

Jan 1, 2000

By Vernon Helm, John S. Ball, Welton J. Wenger, William E. Haines

"INTRODUCTION Although the presence of sulfur causes many petroleum’s to be classified as ""low-grade"" because of the difficulties encountered in manufacturing products to meet rigid specifications, the petroleum industry is finding it necessary to use such crude oils to satisfy present needs. As the demand for petroleum products increases, and available reserves diminish, this utilization of high-sulfur crude oils will be accentuated. Programs designed to supplement the supplies of fuel available from petroleum by the manufacture of synthetic fuel from natural gas, shale oil, and coal are in progress. Such fuels, especially shale oil and, less so, oil from the hydrogenation of coal, also contain sulfur compounds which must be effectively removed. Thus, the need for fundamental research on the sulfur compounds that may be expected in petroleum and allied products is becoming greater as the industry is forced to call upon all available resources to meet the demand for petroleum products. In recognition of this need, the Bureau of Mines has inaugurated a long-range program assigned to furnish fundamental data concerning the presence, characteristics, and effects of sulfur compounds in petroleum and its products."

Dec 1, 1946

By H. B. Humphrey

WHEN THE BUREAU OF MINES was created in 1910, the organic act had as one of its main provisions the following: That it shall be the province of said bureau and its director, under the direction of the Secretary of the Interior, to make diligent investigation of the methods of mining, especially in relation to the safely of miners and the appliances best adapted to prevent accidents, the possible improvement of renditions under which mining operations are carried on, the treatment of ores and other mineral substances, the use of explosives and electricity, the prevention of accidents, and other inquiries and technologic investigations pertinent to said industries, and from tinge to time make such public reports of the work, investigations, and information obtained as the Secretary of said department may direct, with the recommendations of such bureau. The nationwide nature of the health and safety work of the Bureau of Mines has given its representatives an opportunity to study and report on matters pertaining to health and safety in mines and related operations from the time the Bureau was established to the present. Regular annual reports and numerous additional papers and reports have been published each year to place on record and to make available the information gathered. While the basic purpose of this bulletin is to describe health and safety reports for the period January 1947 through June 1955, a selected number of earlier publica¬tions that are believed pertinent for reference purposes are included.

Jan 1, 1956

By J. Douglas Causey

The Bureau of Mines conducted mineral investigations of the Peace Rock and Deadwood River roadless areas in Idaho, in 1992. Literature research was done by the Idaho Geological Survey. The study areas contain black sand placers (thorium, columbium, tantalum, titanium, uranium, and rare earth elements), gold, and molybdenum prospects. Except for unrecorded placer gold, there has been no mineral production from the areas. No mineral resources were delineated, but a multi-million tonne molybdenum resource is in the Big Pine Creek area and a 142 million m' black sand deposit is in the Stolle Meadows, Peace Valley, and Deadwood River areas. The Deadwood mine produced zinc, lead, and silver. There are six mining districts in and adjoining the areas; Warm Lake, Deadwood, Garden Valley/Lowman, Banner, Summit Flat, and Grimes Pass. Few claims, mostly placer, were active in the study area in 1992. The study areas are underlain by granitic rocks of the Idaho batholith. Most of the deposits are alluvial accumulations of heavy minerals weathered out of the Idaho batholith. Stockwork and narrow veins along shears account for the base and precious metal concentrations. Eleven prospects were examined. Workings consist of drill holes, pits and adits. Geothermal resources (hot springs) occur mainly along the Middle Fork Payette River; Vulcan Hot Springs is a designated Known Geothermal Resource Area. Sand and gravel resources are of local interest.

Jan 1, 1993

By Larry Schneider

In recent years, many individuals looking into the future of the blasting industry have predicted that the most likely next technological breakthrough would be the use of high precision, digitally controlled detonators. This seemed logical since not only was there much room for improvement in this area, but any significant improvement in delay timing could yield great benefits in productivity and control of adverse effects. And in fact, within the past two or three years, such electronic detonators have been introduced in the field by a number of different manufacturers. These systems are currently being used in many routine blasting operations around the world which are being closely watched and evaluated.

Jan 1, 2006

By Enzo Palumbo, Joël P. T. Kapusta, François Larouche

In light of the rapid deployment of bottom blowing smelting in China over the last ten years, one has to wonder why it has taken the copper industry so long to adopt ultra-high oxygen enrichment via Savard-Lee type injectors. As early as 1976, Kellogg and Henderson suggested, in their landmark paper on energy usage in the copper industry, that ‘maximum use of oxygen enrichment of process air’ was one of seven ‘energy saving features’ for copper matte smelting and converting. Yet today, shrouded injection and high oxygen enrichment has not been implemented in copper bath smelting outside China and Vietnam. In this paper, the authors explore the reasons why bath smelting processes such as the Noranda Reactor and the Teniente Converter still operate around 40% oxygen enrichment, while the bottom blowing SKS/BBS process typically runs at 65 to 75% oxygen, with all three processes producing white metal. Are there fundamental metallurgical explanations for this striking difference beyond the long-standing skepticism towards high oxygen shrouded injection and its perceived high implementation cost?

Jan 1, 2015

By S. B. Kim, J. Hong, K. Park, W. Kim, H. Kim, Y. Han, J. Choi

"For the first time, the influence of stearyl trimethyl ammonium chloride (STAC) as a collector, on the flotation behavior of lepidolite (Uljin, South Korea) was systematically examined in Denver Sub-A cells. Flotation tests were carried out by varying amount of STAC (50–200 g/ton), feed size (-65, -100, -150, and -200 mesh), and solution pH. The impeller speed of 1000 rpm, flotation time of 10 min and AF-65 (a frother) of 250 mL/ton were invariably applied. In order to complement flotation experiments, zeta potential measurements and XRD analysis were conducted. XRD results showed that the ores were mainly composed of lepidolite, muscovite, quartz, calcite and albite. In addition, zeta potential results showed that isoelectric points were about 2.5, 2.3, and 9.7 for quartz, albite, and calcite, respectively, and lepidolite was determined to be less than 2. Overall, the results of 3-stage flotation showed that Li2O grade and recovery tended to increase with increasing STAC dosage and decreasing feed size. In addition, Li2O grade increased with decreasing pH. The results were explained by the extent of the interaction between STAC and each mineral.INTRODUCTION A great number of potential applications of lithium are being developed currently by the thermonuclear fusion power generation industry(1,2) as well as by the battery and fuel cell industry(3). Even though lithium is mainly consumed in the form of lithium metal and some lithium compounds, about 10% of total lithium production is consumed directly as mineral concentrates by the ceramic industry for the manufacture of special ceramics and mica based glass-ceramics(4). Granitic pegmatites normally contain feldspars, quartz, and mica in addition to lithium-bearing minerals such as spodumene (LiAl(SiO3)2), petalite (LiAlSi4O10), and lepidolite (KLi2Al(Al,Si)3O10(F,OH)2). The amount and grade of metallic minerals tend to gradually decrease and become lower, leading to the increase in the price of base metal or metallic compound(5). Accordingly, recent studies have been extensively devoted to developing the technique to improve the grade of metallic minerals from low grade metallic ores(6,7). Nevertheless, studies regarding the improvement of Li grade from lepidolite ores are very scarce. Lepidolite is a phyllosilicate mineral of the mica group and is often associated with other minerals such as calcite, muscovite, feldspar, and quartz, which need to be separated for lepidolite enrichment(8). Many studies have reported the flotation techniques for separating calcite, muscovite, feldspar, and/or quartz from various targeting minerals(9-11); however, there has been no attempt to investigate physico-chemical properties of lepidolite and its separation from such types of gangue minerals through flotation. Hence, in this study, for the first time, flotation has been carried out for the quaternary ammonium salts (stearyl trimethyl ammonium chloride (STAC, (CH3)3CH3(CH2)16NCl))-lepidolite system based on only the electrokinetic property of minerals that consist of lepidolite ores without adding any depressant to get an initial insight on its flotation behavior. The experimental variables that influence the lepidolite flotation such as amount of collectors, feed size and solution pH have been also examined."

Jan 1, 2015

By B Mead, N D. Pascoe

The Grasberg block cave rail haulage system will be located in the Grasberg mining district on the island of Papua, Indonesia at an elevation of almost 3000 m above sea level. It will transport 160 000 t of ore per day from multiple chute galleries to the underground crushing systems. The design entails approximately 23 km of rail (ballasted and embedded track), over 120 ore chutes to deliver ore to the muck cars and three unloading stations to deliver ore to the crushers. The rail haulage system is a closed-loop system entirely within the underground mining complex.The GBC rail haulage project will be a substantial operation. Trains consist of 11–12 bottom-dump 20 m3 muck cars driven by a 40 t electric locomotive, about 400 t per trainload. Approximately 12 trains and one spare are required to maintain full production at 160 000 t/d. All rail installations will be 1435 mm (standard) gauge with AS60 steel.The rail system is designed to operate in full automated mode, including chute loading, hauling and dumping. The operation will be controlled from a surface control room.The rail haulage project has been divided into five stages, which will be brought online over the course of ten years. Current development and construction are focused on Stage 1 for initial production that will occur beginning in late 2017. This stage includes 24 chutes in three chute galleries, one unloading station, workshop areas and almost 7 km of track (3 km of embedded and 4 km of ballast).This paper describes the key components of the rail haulage system and reports on the current status of development and construction of the system. This paper also overviews the challenges, successes, issues and risks of this project in areas such as scheduling, development, construction and operation.CITATION:Pascoe, N D, Mead, B and Vega, H, 2016. Grasberg block cave haulage project – design and construction update, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 585–598 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By G Tripp, G Lorusso

The Velvet gold orebody (153 Koz Au) is located near the Kanowna Belle gold deposit in the Boorara Domain of the Kalgoorlie Terrane, a subdivision of the Archaean Eastern Goldfields Superterrane (Swager et al, 1990). Gold mineralisation at Velvet is hosted within an intrusion of intermediate composition that broadly follows a sub vertical hanging wall splay of the Fitzroy Shear Zone.Velvet was discovered in 2003 during an underground exploration drilling program targeting potential strike extensions to the Kanowna Belle deposit. Diamond drill hole KDU1595 returned a downhole intercept of 36 m grading 4.6 ppm Au approximately 500 m west of the deposit and at a vertical depth of 700 m below surface in the immediate hanging wall of the primary Kanowna Belle host structure, the Fitzroy Shear Zone. Subsequent drilling completed following the initial discovery, from both surface and underground collar positions, failed to replicate this result.In 2014, KDU1595 was resurveyed gyroscopically and the mineralised intercept correctly located. Additional drilling was undertaken to follow-up the repositioned discovery hole. Challenges included poor drilling angles through the Fitzroy Shear Zone, excessive deviation during drilling and the unknown geometry of the target. Navigational drilling helped to successfully penetrate the Fitzroy Shear Zone and in April 2015, drill hole KDU3234 returned a significant downhole intercept of 45 m grading 5.6 ppm Au.Additional drilling success resulted in a decision to develop a 600 m drive to serve as a dual-purpose access for further exploration and mining. This was a potential risk considering that the orebody geometry was unknown and all significant drilling results were clustered within a 50 m × 50 m panel. Development commenced in June 2015 and the first ore cut taken in April 2016. Geological mapping and structural interpretation, together with multi-element and spectral analysis of drill samples has enabled several other target areas to be identified for exploration. The Velvet mining area is critical to continued production at Kanowna Belle. Geological understanding must advance as mining progresses to ensure continued resource growth and optimal extraction of reserves.CITATION:Lorusso, G, Rogers, J and Tripp, G, 2017. Velvet underground exhumed – discovery and development of a new mining front at the Kanowna Belle gold mine, in Proceedings Tenth International Mining Geology Conference 2017, pp 169–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

A series of flotation experiments were carried out in a 2.25-dm3 laboratory-scale Rushton turbine cell using hydrophobic quartz particles. Flotation was performed at a constant mean bubble diameter over a range of superficial gas velocities and impeller rotational speeds. The overall flotation rate constant increased linearly with increasing superficial gas velocity (and hence bubble surface area flux). The rate constant also increased linearly with increasing energy dissipation, until a maximum value was reached. A further increase in energy dissipation had little effect on the rate constant. The dependency of the rate constant on energy dissipation is a reflection of the size range and hydrophobicity of the particles used in this study. The flotation rate constant increased with increasing particle size, except at the highest energy dissipation value examined, for which the flotation rate of the larger particles reached a plateau and, in some cases, decreased. Good agreement was obtained between the experimental results and those predicted by a fundamental flotation model using experimentally measured values for mean energy dissipation and the Sauter mean bubble diameter. The bubble velocity was adjusted to obtain the best fit to the experimental data. The inferred bubble velocity, based on the flotation model, was found to increase with increasing superficial gas velocity (and bubble surface area flux) and was found to decrease with increasing impeller rotational speed. While the inferred bubble velocities were significantly lower than experimentally measured bubble velocities, and, except at low superficial gas velocity values, significantly higher than the bubble swarm velocity calculated from gas holdup measurements, similar trends with impeller rotational speed and superficial gas velocity were observed in all cases.

Jan 1, 2007

By M Reza Afshar

In this work a mathematical model was developed to study the effect of electromagnetic force on the magnesium melt containing nonmetallic inclusion in an electrical isolated channel. The electromagnetic force exerted on the inclusion induced by DC current field was calculated. A three dimensional turbulent flow equations were solved numerically to compute the velocity field within the channel. On the basis of computed velocity and magnetic fields, the trajectories of inclusions were calculated using the equations of motion for inclusions. Parametric studies were carried out to evaluate the effect of various parameters such as current density, channel diameter and particle density on the removal efficiency of inclusions from magnesium melts.

Jan 1, 2004

By Brad Gunn

Our program has been dictated by the necessity of broadening our markets through converting potash chemicals to fertilizers more in demand than potassium chloride. To this end, we have undertaken studies on methods of preparing potassium sulphate or potassium magnesium sulphate by rather simple conversion. When mixtures of sodium and magnesium sulphates are reacted with potassium chloride, the ratio of sodium to magnesium is quite pertinent. A range of ratios has been selected and the conversions of potassium chloride to sulphate have been assessed by cyclic operations. Results from experimental procedures for producing potassium nitrate are also avail-able. The influence on recovery for systems including organic solvents is assessed for a variety of situations.

Jan 1, 1971

By S C. Labram, A Stabile

"Modern train load out stations are becoming faster and have the ability to load a 100 wagon train in less than three hours. At 70 metric tonnes per wagon, that is an average fill rate of 2333 t/h and considering the train is continuously moving, the instantaneous feed rate into the wagon is in the region of 4200 t/h.The main feed conveyor that maintains the level in the surge hopper, above the final weigh hopper, operates in excess of 5000 t/h to ensure uninterrupted charging of the weigh hopper to not disrupt the train loading operation.To avoid demurrage costs (a charge by the Rail Operating Company for exceeding the contractually agreed loading time) the train has to be handled speedily and efficiently and spend the absolute minimum time at the loading facility. Everything else has a much lower priority, including sampling.Thermo Fisher Scientific’s brief was an engineering, procurement and construction management (EPCM) contract to provide a sampling scheme adjacent to the prepurchased and predesigned load-out facility, but which interfaced seamlessly with the loading system of the trains and provided the following: an instantaneous particle size distribution (PSD) result for each truck loaded, and a final PSD for the total train prior to the train leaving the loading facility a crushed (-3 mm) composite sample for chemical analysis for the whole train a composite physical analysis sample for the whole train.The design presented some interesting challenges to our team, but the end result is a system that not only ‘stands alone’ but interfaces seamlessly with the loading system. This paper discusses the design itself and potential improvements to future systems.CITATION:Labram, S C and Stabile, A, 2017. An automatic sampling methodology to determine contractual particle size distribution in rapid train load out stations, in Proceedings Eighth World Conference on Sampling and Blending, pp 229–234 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 9, 2017

By S. Al-Thyabat

Conditioning of flotation feed is an important prerequisite for efficient flotation. This process depends on parameters such as conditioning time, slurry concentration and slurry pH. The objective of this paper is to optimize the conditioning process for the flotation feed. This was achieved by first conducting preliminary experiments at constant slurry pH to determine the significant ranges of slurry concentration and conditioning time. Then, factorial experimental design (32 experiments) was used to investigate the significance of the above parameters and their interactions on flotation recovery and grade. Statistical analyses using ANOVA approach showed that flotation recovery (R) and concentrate grade (g) were affected by feed conditioning. It was found that concentrate grade was linearly proportional to the slurry concentration and conditioning time, while flotation recovery was exponentially proportional to the conditioning parameters. A contour plot of the flotation response (recovery and grade) against conditioning parameters showed that the optimum operating parameters for flotation feed conditioning was a conditioning time of 1.5 to 2 minutes and a slurry conentration of 55% to 60%.

Jan 1, 2008

By Pan Gu, Zhen Zhang, Jiang Diao, Bing Xie, Hongyi Li

Furnace refractories are in most cases chemically incompatible with smelter slag, which leads to a steady erosion in their thickness over time. Once too thin, refractory walls become mechanically unstable and catastrophic failure can result. Historically, external shell cooling was applied to generate a freeze lining of slag and thus prevent refractory erosion. Many modern high intensity smelting furnaces instead maintain their physical integrity by the use of internally cooled wall panels, plates or finger coolers. An initial refractory lining is often installed inside of the coolers, such that the furnace originally operates with a temperature (insulated) rather than a heat flux (freeze lined) boundary condition. This paper examines the change in slag-wall heat transfer coefficient and slag superheat as a function of process intensity. The implications of the changes in heat transfer on residual brick thickness are explored using analytical modelling.

Jan 1, 2016

By A J. Cornah

Critical decisions in iron ore project evaluation and production are based on global and local spatial estimates of primary mineral deposit properties (such as in situ geochemical grades) and geometallurgical responses (such as screened, washed or concentrated product yields and grades), which are derived from limited sample data. These spatial estimates are typically made using classical geostatistical techniques, which fundamentally assume that the attributes of interest behave additively. This assumption is generally appropriate for æprimaryÆ variables but æresponseÆ variables may behave non-additively and therefore their direct linear estimates may be biased.In this paper an existing additivity testing mechanism is used to quantify the bias resulting from direct linear estimation of a non-additive iron ore attribute. Data from a magnetite project are used to determine the circumstances under which such biases may be of material impact. The implications for iron ore resource estimation, geometallurgical modelling and grade control are outlined and discussed.CITATION:Cornah, A J, 2013. Assessment of the impact of non-additivity in the estimation of iron ore attributes, in Proceedings Iron Ore 2013 , pp 129-136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By D. L. Bickel

This report presents a Bureau of Mines study intended to determine if horizontal stress trends exist and if the stresses can be projected for improved mine design in a selected coalfield. The horizontal stresses were determined in three mines in the Yampa Coalfield and one mine in the adjacent Danforth Hills Coalfield of northwestern Colorado. Stresses were determined from stress-relief measurements using a three-component borehole deformation gauge and overcoring techniques developed by the Bureau. A least-squares method of calculating the average rock stress components in the horizontal plane was performed. Physical properties of the rock from the test sites are also included. For the Yampa Coalfield, the maximum horizontal compressive stress in the floor ranged from 363 to 1,956 psi, and the maximum horizontal compressive stress in the roof ranged from 235 to 875 psi. For the Dan-forth Hills Coalfield, the maximum horizontal compressive stress in the floor ranged from 360 to 1,494 psi, and the maximum horizontal compres-sive stress in the roof was 1,033 psi. Results indicated a trend of low horizontal stresses in the Yampa Coalfield that have not impacted ground control conditions in mines less than 1,000 ft deep.

Jan 1, 1988

Ultrasonic Extinction for High Resolution Particle Size and Concentration Analysis

Sep 13, 2010

By Arnold Hammons

Automated temporary roof support (ATRS) systems have been incorporated into roof bolters since the 1970?s. During roof bolting, many injuries have occurred from large pieces of draw rock falling inby the ATRS beam and tipping back into the operator?s area. Other injuries have occurred due to smaller, sharp rocks falling onto the operator?s hand and arm during initiation of roof bolt drilling. These injuries are attributed to weak immediate roof, sometimes called roof skin failure. Even though ATRS systems support the roof and provide a measure of protection against roof skin failure, additional hazards sometimes do exist immediately inby and outby the supported roof. Design innovations such as the ATRS mounted rocker pad deflector systems have been designed to improve the roof bolter operator safety. This paper will inform the reader of the hazards, machine evolution through different design solutions, and the current state of the art in preventing roof skin failure injuries when roof bolting.

Jan 1, 2009