Search Documents

By Jacques Ouellet, Ferri Hassani

"Within the mining industry paste backfill technology has evolved over the last two decades. This technology aims at producing safe and cost effective backfill of high strength. When used as cemented backfill underground the usual practice in the mining operations was to consider the backfill as a component under the production engineer responsibility. With its growing use in various site conditions some problems were encountered. Over time the mechanical characteristics of paste backfill could deteriorate. Investigations on these problems brought an increased understanding of paste backfill chemistry. Effectively, paste backfill is produced with tailings slurry having sometimes very complex chemistry and mineralogy. The bonding agents can be sensitive to the chemistry of these slurries. Today, a new understanding of the complex chemical reactions involved in cementing paste backfill is derived from concrete research literature. Cemented paste backfill is a manufactured product and as thus all steps involved in its making must be looked at. Both the processing engineers and mining engineers need to be involved. The proposed paper will go over the various developments and new understanding gained over the years on paste backfill chemistry. The authors had the opportunity to work with various Canadian mines that implemented paste backfill in their operations. Chemical alterations case study will serve to illustrate the importance of a good understanding of cement and paste chemistry. The authors will then conclude on research orientations needed to bring a more efficient use of paste backfill technology. The crucial role of the processing engineers in the paste backfill manufacturing will be discussed.INTRODUCTIONPaste backfill is usually prepared from a mixture of solids and water containing at least 15% particles smaller than 20 microns with the addition of binders for mechanical strength. Historically, tailings had been classified to extract the fines and only the coarse part was placed underground as sand slurry. Paste fill was researched in the last three decades to enable mining operations to use all the tailings, including fines, in backfill. The outcome of the early studies showed that paste fill provides high strength but due to preparation complexities and transportation problems is expensive. A greater understanding of the transportation mechanisms and advances in dewatering technology in recent years has resulted in more practical use of paste backfill."

Jan 1, 2002

By Robert B. Hopler

To understand any technology it is necessary that a thorough background of how we got to the present stage is necessary. To do that with the subject of initiation devices we need to begin many hundreds of years ago.

Jan 1, 1990

By W. B. Berwald

[Accurate ~cusirc::ie t of euusu.rface r,resw rus £Uld tee:: ?er:~t:,res in producin+ oil and as wells is one of tine ast iy,ulortant steps ever t,.s:en to place the rprwctice of retroleum ,-iroduction on an exact scientific basis. i'reerures and teial.or-tures in a -petrolcuia r4:, rvoir. have a rn..r..ed influence over the o:wvement of oil and ~c s both within the. reservoir and t~:rou,=Ii the various-size "flow otrin;;u" of proLucin,; wells to tine surface. Knovrled: ?c of theso fc,.ctgrs form a Laois for cny attei:ant to [.,-~ly eciantific j:cthods to the solution or analysio of mc.nj proble;ae encountered in the production of oil and 1c_c, Without a.ccur:tc mcaaurx,ients of reosures r:.nd tcn::paratuxes within the rocervoit and -well 'flo-,r strinL:s" tae aI,licution of w.ny proved enbinecrin and scientific princiy-,loo is on %,]

Jan 1, 1935

By M. Faraji

Inclusions formed in a high-carbon, manganese-silicon killed plain steel (Fe-0.77C wt%) were studied. Various techniques were used to characterise the inclusions, and the latter were classified according to their chemical composition, size and morphology. The main constituent elements entering the inclusions were Mn, S, Al, and oxygen. Alongside MnS and some Al2O3 inclusions many non-metallic inclusions appeared in complex forms, consisting of silicates, sulphides and oxides. Duplex oxy-sulphides, mainly MnS combined with Al2O3, or SiO2 were the most common complex multiphase inclusions in this steel. The nanoindentation technique was used to assess and rate different types of inclusions and data of the hardness and elastic modulus of individual inclusions at room temperature are presented.

Jan 1, 2010

By G. Morizot

La preconcentración es un proceso que permite eliminar material estéril contenido en una mena, cuyo objetivo principal es la preparación del material para el proceso final de concentración. En ese sentido, el presente texto señala las ventajas, los procesos, la molienda selectivas y clasificación, separación magnética y la separación por emisión o adsorción por radiación.

Sep 1, 1981

By R. T. Stain

Integrity testing of deep foundations is now common practice in Europe, indeed in the City of London such testing is a contractural requirement on every site. This paper is in two parts: Part 1 describes the most commonly used test methods and their applications. Part 2 presents a case history where both of the above techniques were used.

Jan 1, 1987

By Steve Kral

More than 111,350 mining and construction industry professionals from throughout the world gathered in Las Vegas, NV, March 19-23 for ConExpo-Con/Agg 2002 and IFPE 2002. The triennial event is the Western Hemisphere’s largest equipment show for the quarrying, aggregates, construction and ready-mixed concrete industries. Despite the difficulties in the world economy, ConExpo-Con/Agg 2002 attracted more than 2,450 exhibitors from throughout the world. This was an increase from the 1,882 exhibitors that were on hand for the 1999show. And this year’s show occupied more than 180,225m2 (1.94 million sq ft) of exhibit space at the Las Vegas Convention Center. This was an increase from the160,900 m2 (1.73-million sq ft) occupied at the 1999event.

Jan 1, 2002

By Michael S. Wieland

"Toxic fumes cause fatal andnonfatal incidents in underground mining, where the working environment tends to trap the fumes, hindering the restoration of non-harmful conditions. Workers can underestimate the residual fume toxicity and return to the work site too quickly. The toxic fumes from charge explosions depend upon a number things: formulation ingredients, mixture uniformity, water resistance, hole contaminates, rock hardness, and dust interactions. Transitory hole-to-hole waves can cause partial desensitization, ruin the reaction kinetics, and worsen the fume toxicity.Traditionally the toxic fume hazard for a candidate explosive is resolved from a requisite tally of fume components. The resolution starts with the fume spectrum, a tabulation of specie concentrations, transformed to standard reference conditions and readjusted to remove the air dilution. The resultant influence, which is referred to as relative fume toxicity RFT, is deduced by a formula rule with some chosen constants and the requisite concentrations. The RFT result is normally compared to an RFT criterion that represents the worst-case (maximum) tolerable fume toxicity, as stipulated by regulations or otherwise."

Jan 1, 1997

By A. N. Kumar

Two fabrication stages in the manufacture of pipelines are identified as causing significant deterioration of the steel plates, namely cold bending and welding. The objectives of this work include quantitative assessment of the degradation of the quality of the steel plate by the loss of fracture toughness, and an estimation of the safe working pressure. The study was conducted on three API grade steels: X42, X46 and X60. After cold bending by the UO technique, various welding technique were employed for joining of the bend plates along the pipe length. A crack-tip opening displacement parameter (CTOD) was used at the onset of initiation and at the first load maxima as the criterion for assessing the toughness degradation under various fabrication stages and regime (such as WZ, HAZ and parent body). In addition, strength, hardness and impact energy values were determined to check the degree of degradation. Microstructural and microfractographic investigation of the fractured samples were also carried out in the scanning electron microscope (SEM). X60 grade steel plate suffers from CTOD toughness loss by around 38 and 55% after welding and cold bending, respectively, for the conditions studied. A combined effect of the two stages results in a loss in toughness by around 70% for the same steel. In X42 grade, the loss in impact energy ranges from 78 to 35 J due to electrical-resistance welding study (ERW). Crack resistance curves are also obtained for the steels to study the crack growth resistance behaviour and to supplement the information on crack initiation behaviour. The orientation of the pearlite banding, as observed on the fracture plane with respect to notch front and applied loading direction appears to have a strong influence on the microvoid-coalescence mechanism of fracture as well as the toughness values. An integrated analysis of the performance of pipelines, considering all these key factors, is discussed.

Jan 1, 2005

By A. Navarra, F. Mucciardi, H. Marambio, R. Parra, F. Oyarzún

"Discrete event simulation (DES) is an appropriate framework for the plant-wide analysis of copper smelters. These smelters apply a common set of chemical reactions: copper-iron sulfides are blasted with oxygen-enriched air, sending the iron into a slag phase and the sulfur into the offgas. Moreover, conventional copper smelters exhibit similar operational dynamics: a smelting furnace operates continually, feeding into an alternating set of converters that produce batches of blister copper. The thermochemical and operational commonalities of copper smelters are integrated within the DES framework. This serves as a common basis to begin evaluating the system dynamics of individual smelters. For complex problems, the simulation framework should be developed in phases, incorporating feedback from different personnel who have complementary perspectives. Sample computations are provided in this paper based on the Hernán Videla Lira smelter, whose production is constrained by meteorological conditions. IntroductionWorld copper production is approximately 18.5 million t/y (Brininstool, 2015), worth $80 billion a year. Out of this total, 75 percent comes from the pyrometallurgical processing of sulfide minerals (Fig. 1), which occurs in copper smelters. The remaining 25 percent is from the hydrometallurgical treatment of oxides and complex ores (Rotuska and Chmielewski, 2008), which uses solvent extraction and electrowinning.The current paper describes the pyrometallurgical processing, recognizing that the underlying thermodynamics and kinetics are well known (Degterov and Pelton, 1999), with the notable exception of minor element transport, such as arsenic (As), antimony (Sb), bismuth (Bi), silver (Ag), gold (Au). The latter is an ongoing area of research, as smelters are faced with increasingly complex ores (Devia, Wilkomirsky and Parra, 2012; Swinbourne and Kho, 2012). This paper focuses on the system dynamics of copper smelter operations, which has received considerably less attention than the chemical thermodynamics and kinetics.Smelter engineers and managers may contribute to the sustainability of their plant by improving their understanding of operational system dynamics. Indeed, we have prompted smelter improvement projects (Navarra, 2016; Navarra et al., 2016; Navarra and Mendoza, 2013) simply by adapting methodologies that are commonly used in other sectors. These previous works incorporate principles from computer-integrated manufacturing (Groover, 2000) and theory of constraints (Dettmer, 2007), featuring the use of discrete event simulation (DES)."

Jan 1, 2017

By Fred L. Bishop

This paper describing the methods employed in the purchasing and supply departments of the Miami Copper Co., Miami, Ariz., is one of a series being prepared for and published by the United States Bureau of Mines on office practice in mining operations. GENERAL DESCRIPTION The Miami Copper Co.'s plant is located about 1 mile from the town of Miami, in the Globe-Miami Mining District, Gila County, Ariz. The property consists of a complete mining plant, concentrator, high-pressure steam power plant, and many other attendant structures. In normal times the company employs about 1,500 men, and mines and mills about 6,000,000 tons of ore annually.

Jan 1, 1932

By J. Nakayama

For drilling large diameter holes for deep foundations, the common and distressing difficulty of long standing has been in coping with ground containing rocky formations and boulders. Where geological formation contains weathered rock or boulders, or deep rock socket is specified, drilling equipment occasionally is found to be unable to drill through and therefore will need supplementary equipment and procedures. Incentive of the MACH Drill Development has been to realize a capable drilling system for rocks of weathered to fresh rock without losing its applicability to usual overburden. Through seven decades' experience of manufacturing and operation of boring machines, the best features of all sorts of drillhead are known such as the drag bit, wing bit, auger bit, diamond bit, rock roller bit, down-the-hole hammer bit, etc.

Jan 1, 1988

By R. S. Warfield

The Kasna Creek copper deposit near Lake Kontrashibuna in the Lake Clark region, Alaska, was the object of an investigative project by the Bureau of Mines during the fall of 1948. Recessed because of inclement weather, it was completed in 1949. This project was a part of the Bureau of Mines program in Alaska for the development of critical and strategic minerals. The ore bodies are contact-replacement deposits in limestone. Mineralization is mainly specular and micaceous hematite associated with chalcopyrite, calcite, chlorite, quartz, and amphibole. The deposit, on the right limit of Kasna Creek approximately 2 miles from the shore of Lake Kontrashibuna, is composed of two mineralized zones that range in altitude from 2,350 to 2,650 feet. This report contains a brief history of the prospect, description of the physical setting of the property, its geology, and the factual results of the Work performed by the Bureau of Mines.

Jan 1, 1951

By Roy A. White

The development of a fire and rot-resistant coating treatment for mine timbers, along with the associated processing technology, is described. Included are a literature search, laboratory studies of polyimide-fungicide coatings, and leaching and fungus growth studies on coated wood blocks. Finally, an economic analysis is performed tor various levels of production.

Jan 1, 1977

By James P. Ludwig

This report provides the results of a two year study of the projected time and cost requirements for new mine development in Wisconsin and is based on a unique blend of information from mining company officials, state regulatory agency officials and contractor experience. Through formal cooperative and review agreements with Kennecott Copy per Corporation, Exxon Minerals Co., U.S.A. and Noranda Mines Ltd., and the Wisconsin Department of Natural Resources plus informal arrangements with knowledgeable Wisconsin persons, lists of the tasks and subtasks required to plan a new mine in Wisconsin were developed. Times and costs were assigned to all tasks and subtasks and these data reviewed by all cooperators. Critical Path Method Diagrams were then developed for a generalized mining project. Total time and cost for the premine planning process was estimated to be 25..1 years and 223 person-years of professional time excluding public affairs effort respectively. By eliminating redundancies in the process and by increasing project efficiency through early public review and participation, recom¬mendations were made to lessen the time and lower the cost of premine planning. The streamlining recommendations could shorten the overall critical path length to 18.16 years and lower the cost to 208 person-years of professional time excluding public affairs effort. The estimated distribution of professional effort (cost) for mine planning in Wisconsin approximates 50.5% for traditional mine engineering tasks, 36.6% for environmental-regulatory tasks and 12.9% for traditional geological-exploration tasks.

Jan 1, 1979

By M. J. Kovalik

The effect of oxidation by air at temperatures ranging from 200° to 390° C on the change of chemical and physical properties of Pittsburgh-bed coal was studied as a function of processing time and temperature. The goal was to prepare a nonagglomerating fuel from a strongly coking coal for use in continuous carbonizing processes and in fixed-bed gasifiers. The oxidized coal was carbonized in a bench-scale apparatus, and the coke strength was evaluated in a Roga tumbler. Strength of the coke was progressively reduced with time of oxidation until the coking power of the coal was apparently destroyed. Time requirements to obtain an essentially nonagglomerating product were inversely related to processing temperature. Gaseous products released from the coal during oxidation reduced the yield of the desired nonagglomerating product, which decreased with time of oxidation at constant temperature and with increase in processing temperature at equal time. Oxidation at a temperature slightly above the lower limit of the plastic temperature range of Pittsburgh-bed coal was most effective because of the short processing time required and moderate processing losses.

Jan 1, 1963

By R. Ramírez, N. Aslin, G. Ríos, T. Bravo, A. R. Almansa

Lacy copper has been an on-going concern at Atlantic Copper for at least 10 years and was first reported to Glencore Technology in mid-2010. Over the past 12 years, many of the plates were replaced due to age and general deterioration however; plate passivation and lacy copper issues have persisted. After analyzing all the possible causes of this phenomena, it was found that the problem is caused by a degradation of stainless steel as a consequence of the deposition of Sb oxides. These deposits act as passivating agents of stainless steel, which reduces the density of copper nuclei, causing defective copper deposit, with low thickness and ductility. After doing several tests for reducing/removing the phenomena, the over-riding factor was found to be the anode-cathode overlap. An adequate overlap eliminates the problem of "lacy copper". This was verified during an eight month trial with anodes extended 2.5cm in length. Longer anode not only avoids the appearance of lacy copper, but also recovers cathodes that already have lacy copper. On the other hand polishing of plates only gives rise to a temporary solution that requires on-going polishing, to avoid the re-appearance of lacy copper. INTRODUCTION The electrolytic copper refinery of Atlantic Copper in Huelva (Spain) was commissioned in 1970 with an initial capacity of 40,000 t of cathodes per year. In 1975 the copper refinery was expanded to 108,000 t/year. From 1994 to 1996, a new expansion together with the implementation of ISA permanent cathode technology led to a capacity of 215,000 t/y. Since 1995, a progressive increase in the current density up to 350 A/m2 has been accomplished, which together with an increase in the number of cells from 1,120 to 1,204, has led to the present cathode production capacity of 290,000 t/y A lack of copper deposition in the lower part of the steel permanent cathodes was first reported in 2010. This phenomenon is known as “Lacy copper” because of the appearance of the copper deposit as it can be seen in Figure 1. The occurrence of this phenomena was relatively low and was assumed to be originated by an excessive anode scrapping. Nevertheless, in December 2015 Lacy Copper was observed in a significant amount of copper cathodes giving rise to the following issues: Increased tramp copper – housekeeping and maintenance problems Poor appearance of cathode deposit and untidy looking bundles

Jan 1, 2019

By Jesse A. Miller

ALTHOUGH the element titanium was discovered by William Gregor in 1790, over a hundred years passed before it was put to commercial use. The first commercial application of titanium was as an alloy additive to iron and steel, and the first ferroalloys were produced domestically in 1906. Titanium pigments were developed somewhat later and have been produced in the United States since 1918. The use of titaniferous material in welding-rod coatings first gained acceptance ill the mid-30's. The metal titanium has only had commercial importance since 1948; domestic production for that year was 10 tons. The relative importance of these major uses of titanium in various forms may he gaged by the consumption of titanium dioxide (Ti02) for these purposes in 1954. Of a total of 440,000 short tons of Ti02 consumed in 1954, 95 percent of the total was consumed for pigments; 2 percent for welding-rod coatings; 1 percent for non-titanium-base alloys and carbide; and 2 percent for miscellaneous uses. The titanium-metal industry is in its infancy, but it has more than doubled its output every year from 1948 to 1954, reaching 5,370 short tons in 1954.

Jan 1, 1957

By Adam Powell, Matthew Earlam

INFINIUM, Inc. is scaling up a new molten salt electrolysis process for producing rare earth metals. Instead of conventional carbon anodes, this process uses Pure Oxygen Anodes™ which employ a stabilized zirconia solid electrolyte between the molten salt and anode. This eliminates two problems with today's rare earth metal production technology. First, it eliminates carbon anodes and contamination of the product by carbon and its impurities, enabling 10-100 times larger batch size than current practice, and lower labor costs. Second, it eliminates emissions of perfluorocarbons (PFC) such as CF4 and C2F6, which are very problematic greenhouse gases with 6000+ times the global warming potential of CO2. The zirconia also enables a sealed vessel with no LiF emissions, creates a reducing environment enabling use of low-cost welded steel vessels, and either produces a high-purity oxygen by-product or can use natural gas to reduce the necessary electrical energy with no HF production. This paper will describe the technology and its current status for rare earth metal production.

Jan 1, 2014

By Marco A. Vera

"This paper investigates the froth function in flotation and the associated upgrading process. Flotation literature has revealed that one of the main functions of the froth phase is the cleaning of bubble-particle aggregates by rejection of entrained material. The cleaning and transport processes across the froth phase exert straining forces on these aggregates on their way up to the froth surface. These forces will impact on the recovery of bubble-particle aggregates.The grade at the top of the froth (TOF) is a parameter related to the quality of particles collected by bubbles in the pulp zone (true flotation). It has recently been demonstrated that TOF corresponds to the maximum practically attainable grade described by the recovery-grade (or enrichment ratio) curve. TOF lumps all the processes experienced by the bubble-particle aggregates before reaching the launder concentrate. This paper describes a methodology for quantifying flotation performance by means of the top of the froth sample - a touch of froth.INTRODUCTIONFroth flotation may be the most important mineral processing technique, but its theory is complex and is not completely understood even though many aspects have been studied and reviewed (Teague, 1998; Wills, 1992).Two distinct particulate systems prevail in the flotation process: a pulp phase and a froth phase (Figure 1). The pulp zone had been studied extensively; however, it is only recently that techniques to measure the froth zone performance have been developed (Contini et al., 1988; Falutsu and Dobby, 1992; Feteris et al., 1987; Seaman, 2002; Vera et al., 1999b).Flotation involves a number of mass transfer processes, occurring in the pulp phase and the froth phase. The formation of the froth and its subsequent removal are considered to be two important steps of the process. Phenomena that occur in the froth phase are known to affect flotation performance significantly (Cutting et al., 1981).Because the froth has a high free surface energy (as a result of the extensive interfacial surface between liquid and air), it appears thermodynamically unstable. The foaming is a dynamic balance, as new bubbles are added continuously from the pulp, while others disappear from the top. Under steady-state conditions, the volumes of added and subtracted air are equal (Booth, 1953)."

Jan 1, 2003