Search Documents

The 112th Annual National Western Mining Conference (NWMC) hosted by the Colorado Mining Association (CMA) drew some political heavyweights, if by voice only, into the fray of two of the hottest topics that the mining industry is currently facing ? climate change and the new energy economy. A changing political landscape in Colorado, as well as in Washington D.C., has given rise to questions about the economic future of the United States and the mining industry?s role in that future. While there has been a recent push away from traditional energy sources to a ?new energy economy? that is rich in renewable energy sources such as wind and solar, the NWMC?s agenda emphasized the role that minerals will play in new energy technologies. The conference was also full of talks about the industry?s role in reducing the United States? reliance on foreign oil and other mineral commodities. To that end, an impressive lineup of speakers were invited to attend the three-day conference Feb. 8-11, in Denver, CO. Unfortunately, Mother Nature had other plans and three of the four headliners, including Denver?s mayor and Democratic candidate for governor of Colorado, John Hickenlooper, were unable to get to the conference because of a massive blizzard on the East Coast locked them in Washington, D.C. However, with modern technology, a full auditorium heard presentations from Hickenlooper, National Mining Association (NMA) president and chief executive officer Hal Quinn and Glenn Kelly, vice president, government affairs for NMA. Republican candidate for governor of Colorado, Scott McInnis, did speak to the crowd in person.

Jan 4, 2010

By M. Kumaran, A. Vetriselvan, A. Purantharan

"This paper presents a case history of evaluating the stability of a distressed earth bund and rectification measures carried out. A 5.45 km long, 7m high earth bund for drinking water storage was constructed in Andhra Pradesh. During construction of the bund following were observed – (a) a longitudinal crack at the downstream side (b) Bund on the downstream side along the crack settled to a max of 700 mm and (c) downstream rock toe level area raised by heave up to 175 mm. Investigation of the events made important contributions to the fundamental understanding of the behaviour of large earthworks of this type. It was found that the variation in subsoil strata was not addressed during the execution.After careful evaluation, stone columns were recommended as a suitable ground improvement technique. Stone columns were used as a reinforcement to improve the shearing resistance of foundation and in turn ensure stability. By using and applying advanced geotechnical engineering analysis tools and modelling techniques, earth bund and its foundation was analysed and examined against failure by slope instability. Stone column design was carried out using in-house computer program GEOSTONECOL and stability of earth bund was analysed using TALREN software. Earth bund construction was completed after ground improvement and is performing satisfactorily.INTRODUCTIONIn order to supply water during summer season, Government of Andhra Pradesh decided to construct a 7m high and 5.45km long earth bund summer storage tank. It was one of the largest earth bund summer storage tanks in whole of South India at the time of its construction. During construction, the earth bund has undergone sudden distresses. Investigation of the series of events occurred during construction has made important contributions to the fundamental understanding of the behaviour of large earthworks of this type. This paper presents the reasons for earth bund failure, slope stability assessment of the distressed earth bund and recommendation of stone column as a suitable ground improvement remediation technique.DESCRIPTION OF STUDY SITEThe characteristics of the original construction are briefly described as follows. A shallow cut-off trench was excavated below existing ground level at the centreline of bund as shown in Fig. 1. Below the base of the trench a cut-off grout curtain was installed. Upstream and downstream shell earth filling was carried out using Clayey Sand ‘SC’ type soil. At some locations, bottom of cut-off trench has reached as deep as 12m from the existing ground level."

Jan 1, 2017

By David R. Winfield

I would like to thank you for spending the time with me today to review the FLIR PathFindIR thermal imaging camera system: It is truly an innovative safety system that has the added benefit of offering increased efficiency Our company the Winsted Group, specializes in mobile video systems that are fully customizable to address standard and unique operational requirements in a variety of industries from heavy equipment cameras to police and military digital recording systems, high end video camera systems are a hallmark of Winsted?s product line. The use of thermal imaging camera systems to enhance mobile safety is a relatively new concept as it relates to their use in both transportation and heavy equipment operation. This technology, like so many before it, has been adopted for civilian use from its military roots. The identification of enemy combatants through their heat signature has given our troops a decisive edge in military operations in total darkness Likewise, the ability to discern people and objects that give off heat is a significant step forward in collision and accident avoidance. The PathFindIR camera system that I am demonstrating today is so advanced that it cannot be exported outside of continental North America without a US government approved export license I would like to commence my presentation with a short video clip that discusses the technology associated with the FLIR PathFindIR Thermal Imaging camera systems. The video demonstrates the operational effectiveness of thermal imaging camera systems installed on a vehicle operating on the roadway at night, of course there are definite parallels to use in a mining environment, primarily the fact that lighting is limited and the chance for vision limiting dust is ever present. We are, of course more concerned with personnel safety in our mines than encountering wildlife on the roadside. From the same perspective, the transport driver is just as concerned with encountering a stalled vehicle as our mine truck operators are with other mine traffic.

Feb 1, 2008

By Laurence A. Dahners

As part of the strategic minerals program, the Bureau of Mines conducted a diamond-drilling project on three barite properties in eastern Tennessee and western North Carolina during the summer and fall of 1944. These properties, the Moccasin Gap prospect and the Krebs property in Cocke County, Tenn., and the Sandy Bottom mine of the Stackhouse group in Madison County, N. C. (fig. 1), are known to have produced some barite. The Bureau of' Mines project was planned to prospect for extensions of the ore bodies. A total of 3,169 feet of diamond drilling was done in 15 holes on the three properties. Tabulations of sample analyses and drill-hole logs are presented in this report. Two other mines of interest in the area are the McCoy and the Williams in Cocke County, Tenn. The Williams adjoins the Krebs. No drilling was done by the bureau in either of these properties.

Jan 1, 1949

By Oliver C. Ralston, Dorsey A. Lyon

The data reported in this bulletin are largely the result of experiments conducted by the Salt Lake City station of the Bureau of Mines in cooperation with the department of metallurgical research of the University of Utah. The work on lead is only one of the phases of the investigations carried on at that station during the years 1914 to 1916. The results of similar work with zinc ores and with copper and other ores will be published in future reports of the bureau.

Jan 1, 1918

By Joshua Hoffman, Braden Lusk, John Rathbun

A Flyrock Prevention Taskforce was established in Kentucky with the support of Kentucky's Department of Natural Resources, Kentucky's Explosives Industry, and the University of Kentucky. This paper presents the initial work of the Flyrock Prevention Taskforce towards its missions of identifying the root causes of flyrock incidents based on the analysis of previous events, and tracking the progress of flyrock elimination in the future. Work identifying root causes of flyrock events is presented through the development of a database which manages information about the blasts which caused flyrock. This data includes: blasting and seismograph records, drill logs, videos of the event when available, company notes/incident reports, and any additional information regarding probable cause. Work tracking the progression of flyrock elimination efforts is presented in this paper through the introduction of a flyrock index. Several metrics are proposed for this index, and are discussed for their appropriateness and shortcomings. In order for these indexes to be valid forms of tracking flyrock incident rates additional records must be kept and reported, such as the annual consumption of explosives by surface coal blasting. Suggestions for record keeping, flyrock investigation practices, and means of tracking flyrock incident rates are proposed in this paper.

Jan 1, 2013

By Douglas Bartley, Jay Elkin

The state of Pennsylvania was at one time one of the leading coal producing states in the east. However, legislation and industry trends over the last 10 years have adversely affected the amount of bituminous coal mined in Pennsylvania and the whole eastern United States. The application for and approval of a new mining permit is a very costly and arduous task. When a new mining operation is established it is crucial that nothing within the operator’s control causes the operation to stop producing. This paper discusses the action taken by a small mine in Pennsylvania when their blast induced vibrations rose to levels that typically would have resulted in a total mine shut down by the regulatory body governing such operations.

Jan 1, 2003

By E. L. Garton

The Bureau of Mines for a number of years has been conducting an investigation of crude petroleum from producing fields in the United States and the Western Hemisphere and has published a series of reports on these fields. Analyses of crude-oil samples from many oil fields of Oklahoma are given in Bulletin 2913. Analyses of 21 representative crude oils from various producing zones of the Oklahoma City field are given in this report. A close study of the analyses reveals very few differences in the general characteristics and chemical properties of these oils.

Jan 1, 1932

By Pierre Beaudoin

"This paper deals with the repairs made on two damaged mills. It investigates briefly the causes of the damage, explain its nature and the design of the repair. It explains the detrimental effect on operation and the solutions implemented to reduce them. Finally, to review the follow-up required for such repairs. LOCATIONThe Holt McDermott Mine is located 75 kilometers Northeast of Kirkland Lake and 30 kilometres west of the Quebec border in Northeastern Ontario. The town of Kirkland Lake is located approximately 500 kilometres north of Toronto. HISTORYThe discovery of gold in Holloway Township dates back to early 1920. In 1984 Barrick Resources, which amalgamated with Camflo Mines, acquired more claims on the property and initiated an extensive drilling program. By 1985, the drills indicated reserve increased to 2,500,000 tonnes grading 6.8 g/mt. In 1986 a production decision was made and in 1988 the mine was officially opened.As of December 31, 1998, 4,691,507 tonnes grading 5,66 g/tonnes have been milled from 4 ore-bodies. The mill started up in June 1988."

Jan 1, 2001

By J. Geisler

When addressing Germany’s resource supplies, we need to distinguish between those domestically available and imported ones. Resource extraction ostensibly competes with the designation of protection areas. However, the parallel existence of wildlife and plant life, and operations in the areas used for resource extractions is continually underestimated. The European Commission has compiled guidance documents facilitating the extraction of resources from protected areas. With regard to resource productivity, the market appears to be the appropriate instrument for minimising resource consumption. Policy makers are now called upon to create a legal framework leading to a consensus accepted by society.

Jan 1, 2011

By Zhuo Chen, Jun Zhou, Jiemin Zhou

Samples of the reacting suspension particles were taken from the reaction shaft of a commercial flash furnace at different heights. The processes of matte and slag formation and morphology of the samples in the shaft were observed and analyzed. Variations of matte and slag composition in the shaft were investigated. By analyzing the samples taken from the settler at different locations, settler processes were studied such as slag formation, agglomeration and separation of matte-slag phases, Fe3O4 reduction, copper-in-slag reduction etc. In accordance with the characteristic of matte and slag formation the flash furnace can be divided into 6 functional regions, and a mechanism model called as “Micro bath process” is proposed for matte and slag formation in a commercial flash furnace. INTRODUCTION During flash smelting, concentrate particles scattered in the reaction shaft complete their oxidation reactions in suspension. The droplets produced fall into the settler beneath with a small amount of un-melted solid particles, agglomerate and separate into matte and slag layers which are tapped out from their tap holes separately. With respect to the extent of slagging reaction in the reaction shaft, there isn’t any commonly accepted understanding in literature (Kimura, Ojima, Mori & Ishii, 1986; Kemori & Kondo et al.,1988; Kemori, Denholm & Kurokawa, 1989; Fagerlund &Jalkanen, 2000). Some assume that the slagging reaction in the shaft can be ignored and some propose that all slag is produced in the shaft. With regards to the characteristics of the physical-chemical changes of concentrate particle in the reaction shaft, although there are some research results reported from pilot scale and commercial scale experiments (Kemori, Ojima & Kondo, 1988; Hagni, Vierrether & Sohn, 1988; Jorgensen, Taylor, Dickinson & Stevenson, 1992; Swinbourne, Simak & Yazawa, 2002; Kivinen & Tuominen, 2005), they are generally limited themselves to theoretical analysis and calculations. No studies are published concerned with the processes of matte and slag generation in the shaft, quantitative analysis of the processes, variations of matte and slag composition and morphologies of the melts along the axis of the shaft, etc.

Jan 1, 2019

By L. Flett, S. Woods, C. Deredin

"Following a significant reduction in world Imperial Smelting Furnace (ISF) capacity from 2003 to 2008, a major optimization initiative was successfully carried out on the lead upgrading and bulk (zinclead) flotation circuits in the Brunswick Concentrator.This paper describes the process improvements that have taken place in order to reduce the quantity of bulk concentrate:•,Increase in lead upgrading rougher flotation circuit capacity•,Installation of a closed-circuit bulk regrind utilizing MillPebs and 150 mm Cavex hydrocyclones•,Installation of two additional cleaner flotation stages on the bulk circuit•,Optimization of the manipulated variables in the lead upgrading and bulk circuitsINTRODUCTIONThe Brunswick Mine (Xstrata Zinc Canada) is located near Bathurst, New Brunswick and is one of the world’s largest lead/zinc mines. Milling of ore commenced in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore from the No. 6 open pit mine. The planned closure of the mine will take place at the end of the first quarter in 2013. The ore is a complex massive sulphide, consisting of approximately 20% valuable minerals, 60% pyrite and 20% silicates.A simplified flowsheet for the concentrator is given in Figure 1. The overall flowsheet involves SAG milling, secondary ball milling, selective flotation, and dewatering by thickening, filtering and drying. The complexity of the flowsheet evolves from the requirements for fine grinding and the production of four concentrates: zinc (sphalerite), lead (galena), copper (chalcopyrite) and bulk (sphalerite plus galena).Primary hydrocyclone overflow feeds the copper-lead aerator-roughers for flotation at pH 9.0 with soda ash. Plant xanthate (80-20 sodium isopropyl and potassium amyl) and AP407 are used as collectors in the copper-lead circuit. The rougher concentrate is directed to the copper-lead regrind circuit and the tailings are fed to the secondary grinding circuit. The secondary hydrocyclone overflow from the secondary grinding circuit feeds the copper-lead rougher-scavenger banks. Rougher concentrates are reground to a P80 of 28 µm prior to three stages of copper-lead cleaning. The first stage of cleaning is done in an open circuit with the tail reporting to the cleaner scavenger. The cleaner scavenger concentrate reports to the regrind circuit and the cleaner scavenger tail combines with the rougher/scavenger tail to feed the zinc circuit. The second and third stages of cleaning are performed in closed circuit with the cleaner tail being recycled to the copper-lead regrind circuit. The average final concentrate grades 23% Pb, 3% Cu and 704 g/t Ag, and is fed to the copper separation circuit."

Jan 1, 2013

By I. Tsolas

This paper presents the use of non-parametric approach (i.e., data envelopment analysis, DEA) for the development of environmental sustainability indicators in mineral processing using environmental, economic and/or integrated indicators (i.e., indicators that interrelate two dimensions of sustainability). A case study based on real publicly available data is presented to illustrate how the proposed approach can be implemented in practice. The merit of this approach, which is based on the productive efficiency framework, is that it provides environmental sustainability indicators that can be used internally for benchmarking purposes and externally for sustainability reporting.

Jan 1, 2008

By Alain Blouin, Mohamad Sabsabi, Aissa Harhira, Paul Bouchard, Greg Lithgow

"The objective of this study was to demonstrate the application of Laser-Induced Breakdown Spectroscopy (LIBS) to the continuous analysis of online monitoring of Al, Mg, Ni, Mn, Si and Fe in nickel ore limonite and saprolite slurry samples. Analysis was performed on slurry samples in air at atmospheric pressure. Two pure samples of limonite and saprolite were used. Mixtures of the two samples in varying proportions were used to build calibration curves, study the influence of solid/liquid ratio, and evaluate short and long term reproducibility. The LIBS measurement of these elements is independent of the water content (from 70-85%, the range allowed by our setup). Repeatability of the measurement and long term reproducibility (from day-to-day) were below 1.2 % and 2% respectively for all the elements studied in our conditions. The results obtained showed that an industrial LIBS analyzer could provide the chemical composition of the six elements Al, Mg, Ni, Mn, Si and Fe within 1-2 minutes.IntroductionThe metal-producing industry faces the major challenge of increasing productivity, reducing costs, and maximizing benefits from existing equipment. By pyrometallurgy, metal making involves the basic steps of charging the furnace, melting the charge and refining. By hydrometallurgy, the metal refining is carried out through the dissolution of the metal by chemical reaction and electrolysis. During refining either by pyrometallurgy or hydrometallurgy, it is critical that operating parameters be adjusted and controlled so that the chemistry of the melt or the solution is within predetermined limits. Presently, the complete turnaround time for sampling, sample transfer, analysis and communication of the results to the operators is often 30 minutes or more."

Jan 1, 2016

By David J. Hoadley

This report describes the development and limited testing of a semi-automatic, raise climber, Compact Service Hoist System designed for stope access in underground metal and nonmetal mines. Demonstrated capabilities of the system include a 1,000-lb payload capacity, control from the traveling cage and from up to three remote stations, operating in vertical or inclined raises 3 ft in diameter and up to 300 ft in length and a travel speed of 50 ft/min. The system has the capability of operating in crooked raises because the conveyance climbs two stationary wire ropes suspended down the raise. The drive unit is electrically powered with power and control signals supplied to the drive unit through an umbilical 'cable also suspended down the raise. The system has been designed for portability, ease of installation and minimum raise development. The hoist has been demonstrated successfully in an above ground test tower. This report provides a detailed description of the hoist design and its demonstrated performance to date.

Jan 1, 1985

By Ahmad Ghahreman, Lin Li

Silver and cupric ions have been proven to play the roles of catalysts to promote the oxidation kinetics of chalcopyrite in acid solution. In this study, the interaction between silver ions and cupric ions during ferric leaching of chalcopyrite in sulfuric acid solution has been investigated. The electrochemical study by Tafel analysis showed a significant boost of dissolution rate for chalcopyrite dissolution in Fe3+- Cu2+ containing sulfuric acid solution after Ag+ was added in the solution. For 10 ppm Ag addition, the dissolution rate of chalcopyrite increased to 7.94 ×10-6 A/cm2 from 3.2 ×10-7 A/cm2, when Ag+ was absent. On the other hand, the effect of Cu2+ on the dissolution of chalcopyrite in Fe3+-Ag+ containing sulfuric acid solution was not obvious from electrochemical measurements. The chalcopyrite leaching tests in different acid solutions showed that silver addition had an obvious catalytic effect on promoting chalcopyrite dissolution. Comparing the leaching rates of chalcopyrite leached in Fe3+ containing, Fe3+-Ag+ containing, Fe3+-Cu2+ containing and Fe3+-Cu2+-Ag+ containing sulfuric acid solutions, it was found in Ag+-Fe3+-Cu2+ containing sulfuric acid solution, the leaching rate was highest among all the aqueous acid systems. Further leaching tests suggested that with increase of the Ag+ concentration from 0 to 20 ppm, the leaching rate of chalcopyrite in Ag+-Fe3+-Cu2+ containing sulfuric acid solution also increased and reached 57.62% with 20 ppm Ag+ addition after 24 h. INTRODUCTION Chalcopyrite is the most important copper mineral in copper hydrometallurgy and it accounts for nearly 80% of the universal copper resource (Olvera, Rebolledo, Mora, Dixon, & Asselin, 2018). The hydrometallurgy of chalcopyrite has been intensively studied with emphasis on solving the slow dissolution kinetics of chalcopyrite in acid environment. A variety of aqueous systems, such as sulfate (Hiroyoshi, Miki, Hirajima, & Tsunekawa, 2001), chlorides (Liu, Chen, & Yang, 2017), and ammonia (Hua et al., 2018) have been studied to improve copper leaching. From another perspective, chalcopyrite leaching studies have indicated that the mechanism of chalcopyrite dissolution in acid solution is essentially electrochemical (Li, Kawashima, Li, Chandra, & Gerson, 2013). Therefore, extensive studies have recently been carried out to explain the dissolution kinetics of chalcopyrite in different media by various electrochemical techniques.

Jan 1, 2019

By Paul. E. Pesonen

Since early in 1940 the Bureau of Mines has been concerned with possible means of utilizing manganese-bearing materials from the Missouri Valley manganese deposit. During the period between July 1945 and August 1947, the Bureau of Mines undertook to complete certain phases of the problem by re-evaluating the results of earlier work and supplementing the findings by additional operations and field studies considered necessary to permit drawing of final conclusions. Distinctive discoloration marks the outcrop of the manganese deposit which is exposed on both flanks of the Missouri River Valley and its major tributaries for a peripheral distance of approximately 523 miles in south-central South Dakota. The apparent magnitude of the deposit, judged largely from observation of the outcrop, had led to much speculation as to its actual value in terms of tonnage and grade. Similarly, investigative work aimed at developing a means of winning a usable manganese-rich product from the deposit had reached no conclusion, except that certain methods showed more promise than others for accomplishing the final objective.

Jan 1, 1948

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1952 was made under a co-operative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 94 samples of aviation gasoline which include, for the first time in this series of reports, data on five samples of grade 108/135 aviation fuel. Data also are given for 34 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers? production in their laboratories and the results submitted to the Bureau of Mines for compilation. The products of 20 manufacturers of aviation gasolines and of 16 producers of aviation jet fuels are represented.

Jan 1, 1953

By Mustafa Akser

The Pipestone Lake anorthosite complex in Manitoba, Canada, was recently been re-identified as a potential source for titanium, iron, and vanadium. The present study utilized a 350 kg hard rock sample, which originated from the "Main Central" zone of the deposit. Commercial pilot-size equipment, such as dry low intensity roll magnets, wet high intensity magnets (WHIMS), and high tension electro-dynamic roll separators, was employed. As products, ilmenite up to 48.5% TiO2, and magnetite concentrates up to 87.9% Fe3O4 with 5.25% TiO2 were obtained. The majority of the vanadium reported to the magnetite concentrate. Subsequent characterization of various separation products shed light on the potential grade and recovery of the minerals from this deposit.

Jan 1, 1996

By Qian (Ken) Liu, Remi Proulx

A large scale blast damage project was carried out over the past two years at INCO Ltd Manitoba Division co-funded by the Canada/Manitoba Mineral Development Agreement. The experiment was conducted at the T-3 Mine in two mining stopes with an experimental drift developed in the hanging-wall for the installation of monitoring instrumentation. The objective was to observe and subsequently to reduce ore dilution by monitoring the performance of blasts, the hanging wall movement, as well as the cavity of the open stopes.

Jan 1, 1995