Search Documents

By I. B. Cadoff, J. C. Bilello, R. Rosenberg

Diffiusion of magnesium into the surface of LiF crystals to controlled depths and subsequent heat treatments provided a wide range of surface zone harahesses and structure, The bend strength of the LiF crystals was increased by as much as an or-dev of magnitude. Ductility was achieved when dislocation generation occurred in the diffusion zone or when dislocations penetrated to the surface from the intevior. A critical surface hardness of 130 to 140 kg per sq mm was found helozu which generation could take place in the diffusion zone and ahoue which the zone was impenetrable, This hardness was obtainable by several methods, among them the aging of quenched MgF2 -LiF solutions to produce MgF, precipitation. Maximum hardness was ohtained in quenched specimens with no visihle evidence of MgF,. Diffusion-zone formation followed a parabolic rate law and an activation energy of 20.9 kcal per mole was obtained for the process. RECENTLY, the properties of ionic crystals as related to surface condition have been receiving much attention, specifically the transitions between ductile and brittle behavior. Originally Joffe 1 showed that NaCl crystals could be made ductile by immersion in water and related this to the elimination of surface microcracks. Aerts and DeKeyser 2 and Gorur 3' have subsequently shown that ionic crystals are inherently ductile and are embrittled through contact with air. Machlin and Murray4 hypothesized that a layer of NaCIO3 produced by contact of ozone with NaCl induced embrittlement by acting as a barrier to outward dislocation flow. westwood,' Rosenberg and Cadoff,9 and Bilello and cadoff' have reported surface strengthening of LiF crystals by coating with a magnesium compound and then heat treating for adherence. The major effect of the coat was to inhibit dislocation-slip lines from reaching the specimen surface. westwoods showed microcrack formation and fracture to be caused by slip-band interactions at the surface. The material presented in this paper is an extension of the work reported earlier by Bilello, Rosenberg, and cadoff'6,7 and illustrates the wide range of surface properties and bulk behavior obtainable by use of heat-treated magnesium-diffused surface regions in LiF crystals. EXPERIMENTAL PROCEDURE The LiF single crystals were obtained from the Harshaw Chemical Co. Some batch to batch variation was observed; therefore all specimens for a given test series were cleaved from the same crystal. The typical dimension used was 1 by 0.1 by 0.40 in. Surface damage resulting from cleavage was removed by chemically polishing in a 2 pct NH4OH solution. Each group of specimens was given a vacuum anneal at 700°C for 4 hr to provide a base standard for measuring comparative effects of various surface treatments. To produce the reacted surface zone, the annealed specimens were immersed in a boiling suspension of MgF, in doubly distilled HzO, agitated slbwly for 30 sec, removed, and dried at room temperature. Uniform coatings of MgF, were deposited with a thickness of approximately 5 mils. It should be noted that this technique can be modified for use with crystals which are soluble in water by using boiling absolute alcohol as the dissolving medium. This was found effective for the coating of NaCl with MgF2. The diffused surface zone was obtained by annealing the coated samples at elevated temperatures in a vacuum of lob4 mm Hg. Penetration depth was controlled by varying the annealing time from 1/2 to 28 hr. After heat treatment, the samples were tested for bend strength and hardness. Load was applied by four-point bending in a hard-beam testing jig. Four-point rather than three-point bending was used to provide a wide area of constant stress and to minimize the effect of localized inhomogenities in the specimen. The deflection rate was 8 x min-' and the distance between knife edges was 1/4 in. Load-time curves were obtained from a chart recorder coupled to the machine and converted to resolved shear stress on the shear plane vs deflection, as plotted in the figures. The unstressed portions of the sample outside of the two outer knife edges were used for the microhardness studies. Microhardness measurements were made with a Bergsman tester attached to a Reichert metallograph. All hardness impres-

Jan 1, 1964

Current mine ventilation systems have evolved from simple, limited energy, series or multi split layouts motivated by low suction, slow running, surface fans. Concentration of coal production from fewer working places and ventilation splits, and varying needs, hazards and challenges, however, have led to substan- tial changes. Modern ventilation systems, therefore, are more complex, sometimes more interdependent on others, more energy intensive, and are founded on the use of multiple airways and greater suction, higher speed surface ventilators and often booster fans. Intensi- fication of output has resulted also in higher gas emission rates, the wide adoption of fire- damp drainage, and sometimes in particular problems such as spontaneous firedamp emissions. Some coal mines are subject to spontaneous outbursts of coal and firedamp. These and related matters and current practices and developments are leading to discernible trends, potential advances, and further changes in Practice.

Jan 1, 1983

By Pol Duwez, H. E. Martens

The high temperatures encountered in the operation of jet engines have imposed most drastic requirements upon the materials used in their construction. There are two different approaches to the materials problem connected with the design of parts in contact with high temperature gases. The first approach is to use a material which will perform satisfactorily at a temperature comparable to that of the gas. The second approach is to use a cooling system so that the material is maintained at a temperature appreciably lower than that of the gas. Besides the conventional method of cooling by means of a liquid in contact with the material exposed to a high rate of heat transfer, a less orthodox method consists of making the part to bc cooled of a porous material', so that the cooling fluid can be forced through the pores, In this scheme, the temperature of the coolant moving in a direction opposite to that of the heat flow increases gradually while passing through the porous material, and the coolant forms a protective layer on the surface exposed to heat, This method, referred to as ((sweat cooling," was pro- posed at the Jet Propulsion Laboratory in September 1944, and the experimental work on the preparation of porous metals was started early in 1945. The sweat cooling method opens new lines of research in powder metallurgy by extending the field of application of porous metals. The porous metals available at the present time are used mostly as bearings or filters, and a rather limited number of alloys are made for these applications. In addition, the fabrication of bearings or filters does not require a very close control of the permeability, while in the case of sweat cooling such a control is of primary importance. In designing a sweat cooled part it is imperative to assure a given rate of flow of coolant under certain conditions of Pressure drop. Generally, the Proper pressure drop and the rate of flow of coolant are deduced from heat transfer and design considerations, and consequelltl~ the Permeability of the Porous metal to be used is also determined. It is therefore necessary for the designer to have available a continuous series of porous metals covering a range of permeability as wide as possible. Contrary to the requirements established in the fabrication of filters, the actual pore size of a porous metal intended for sweat cooling is of little consequence, except for its effect on permeability. The tensile strength is likely to be of great importance for some applications. Since the tensile strength of a porous alloy decreases with increasing porosity, an important problem is to develop porous alloys having the maximum permeability with minimum porosity.

Jan 1, 1949

By J. T. Eash, N. B. Pilling

As a group, the alloys of iron, nickel and carbon are, in application, one of the most versatile of the ferrous alloy family, and while many investigations have been made of their properties and structure only a few attempts have been made to show the microstructural relation over a wide range of composition. It is neccssary at once to be clear about the kind of structural relation with which we are concerned. The equilibrium diagram provides quantitative data regarding structural make-up and its variation with temperature, but equilibrium structures often are far different from the technologically significant ones. This is particularly true of steels and cast irons, and some of the most important cornponents of their structure may have no place in the diagram of equilibrium. The fugitive phases that result from transFormation are dealt with in a highly detailed and descriptive manner in. the S-curves originated by Bain. The present effort lies in a still different field, which is to portray the relation between sweeping changes in composition and in resultant structure, under controlled but nonequilib-rium conditions of thermal treatment. The Guilletl diagram presented in 1903 was the initial attempt at such a correlation and frequent references to this diagram can be found in the literature even though later work has shown it to require considerable modification. Kase2 published in 1925 a diagram that was based upon observations of furnace-cooled melts: At low carbon contents this diagram agreed fairly well with experience in showing pearlite to exist in alloys containing up to 6 per cent nickel, and completely austenitic steels at 24 to 28 per cent nickel. At high carbon contents, however, irons were indicated as being martensitic at around 2 per cent nickel and austenitic at 12 per cent nickel; these interpretations are open to serious question. Based upon experience with steels and cast iron, Wickenden3 suggested a diagram that agreed fairly well with Kase's in the steel range but which presented a wide departure from it in the higher-carbon, high-nickel regions. In its broad picture, the Wickenden diagram is an approach to "practical" structures. Reference may be made at this point to the efforts of Marsh5 to construct an iron-nickel-carbon equilibrium diagram by the coordination of scattered data, which are described at length in the monograph cited. None of these preceding attempts has appeared to meet the need for an exposition of the structural sequence that is encountered in traversing the nickel-steel nickel-cast-iron range under what might be called ordinary departures from equilibrium. ExperimentaT. Conditions Since the intent has been to establish structures developed under arbitrary conditions, experimental details have perhaps more than usual importance. Three of these conditions should particularly be noticed: (I) the material was cast and not subjected

Jan 1, 1942

By R. I. Jaffee, J. G. Dunleavy, W. Hodge, H. R. Ogden

IN a search for an improved conductor for use in field wire for the L. S. Army Signal Corps, an alloy of copper and silver was developed from which it was possible to obtain 29 B & S ga. strands with tensile strengths in excess of 160,000 psi combined with an electrical conductivity of over 70 pct IACS. Such a favorable combination of strength and electrical conductivity has not been reported previously in the rather extensive literature covering this subject. The properties obtained from various binary alloys of copper and silver, together with the method of fabrication of these alloys which has been developed to obtain the properties desired in fine wire strands, are discussed in this paper. LITERATURE The effect on the electrical conductivity of copper of the various elements in solid solution is shown in Fig I, taken from published data by J. O. Linde and others.' It will be noted that silver in solid solution depresses the electrical conductivity to a lesser extent than any other element for which data are given, and is followed rather closely by cadmium, and then by chromium. Zinc, which lies between cadmium and chromium, has so high a solid solubility in copper that the data for zinc are scarcely comparable to the data for the other two in the range covered. Not many data are available on the strain hardening of copper-rich Cu-Ag alloys. Corson2 reports a 3 pct Ag alloy properly cold worked and annealed to have 100,000 psi tensile strength and 90 pct IACS conductivity. On straight cold working, Hessenbruch3 reports 101.000 psi for a 5 pct Ag, 0.3 pct Be alloy, and 129,000 psi for a 30 pct Ag, 0.5 pct Be alloy. Here it would he expected that much of the strain hardening came from the silver content of the alloys. The copper-rich side of the Cu-Ag diagram, according to Stockdale,4 is shown in the upper part of Fig 2. The electrical conductivities for copper-silver alloys annealed at 750 and 350°C, taken from the work of Johansson and Linde,5 are shown in the lower part of Fig 2. The sloping line corresponds to the conductivity of solid solutions of silver in copper, and the horizontal offshoots correspond to the conductivity of the two-phase alloys in equilibrium at the two temperatures shown. The electrical conductivities are very high, even for the 750°C anneal. The potentiality for age hardening from supersaturated alpha copper solutions appears to be excellent from the solubility line, but Smith and Lindlief6 have shown that the response to age hardening of solution-annealed alpha alloys is not good. They found that the tensile strength of a 5 pct Ag alloy aged at various temperatures was not as great as in the quenched condition, even though, anomalously, the hardness increased from RB68 to RB78 by annealing for 4 hr at 400°C after a 750°C quench. Weist7 also found that the alloys increased in hardness

Jan 1, 1948

By Catharine T. Fogg

The U.S. Bureau of Mines investigated the availability of platinum, palladium, and rhodium from 16 deposits in four market economy countries (MEC's). Major recoverable products include 164 Moz of platinum, 80 Moz of palladium, 13 Moz of rhodium, 24 Moz of ruthenium, 4 Moz of Iridium, 2 Moz of Osmium, and 10 Moz of gold. The 12 deposits in the Republic of South Africa are estimated to account for 96.7 pct of total recoverable platinum. The base-case scenario estimates the long-term cost of production including recovery of capital, but provides no return on the investment or O-pct discounted cash-flow rate of return (DCFROR). The total production costs in January 1990 U.S. dollars ranged from $325/oz to $1,288/oz of platinum compared to an average January 1990 price of $492/oz. Approximately 83 pct of total recoverable platinum was economic at a cost level of $4S0/oz or less. At the IS-pct DCFROR, only 26 pct of total recoverable platinum was economic. For platinum-group metals (PGM), attention has been focused on the ratios of the three primary metals: platinum, palladium, and rhodium. Sensitivity analyses were performed to determine the impact long-term rhodium price increases could have on the total cost of production for platinum and palladium.

Jan 1, 1993

By Tony Lipiec, Ian Orford

"A key part of plant design is the selection of the design tonnage which is the hourly tonnage target that the equipment selection is based on. Its selection is critical for ensuring that the nominal tonnage which is critical to the financial performance of the project will be met. With deposits being developed at lower grades, higher tonnages and a higher degree of hardness variability, it is essential to ensure that the design process selects the comminution equipment which will be able to deal with the impact of this ore quality variation.Ore hardness and its variance are key factors to be taken into consideration for the selection of the design tonnage. It is well accepted that for the nominal or name plate tonnage to be consistently achieved, it is necessary to base the design tonnage on a hardness value greater than the average ore hardness of the deposit to be mined. The question is how much greater should this design value be to ensure that the nominal tonnage is met to the satisfaction of the project financial model. Standard industry practice is to set the design tonnage by:1. Select an ore hardness percentile that is greater than the average ore hardness to be the basis of the nominal tonnage. Typically either the 75th or 80th percentile value from the data set will be selected.2. Selection of a design factor to multiply by for determining the design tonnage, i.e. the design tonnage = tonnage (based on the average ore hardness) multiplied by design factor.This paper discusses the selection of the design ore hardness through the use of modelling or the use of a design factor. It further shows the impact of ore hardness variance on the capacity of the process and its ability to meet the nominal tonnage. Insight is provided as to what ore hardness percentile value should be selected balancing the shortfalls of tonnage for ores harder than the design value versus the above target production achieved for ores softer than the design ore hardness."

Jan 1, 2016

By A. E. Worthington, R. F. Meldau

An analog computer study was made of the reduction of the magnitude of the SP by formation geometry and resistivity effects. Practical field .situations were studied. The analog data were converted to the form of departure charts. These charts may he used to determine the reduction in the SP due to the above eflects pith good precision Quantitative interpretation of the SP log in terms of formation water resistivity is presently based on the premise that the observed SP is equal to the electrochemical potential developed across a shale between the mud filtrate and the formation water. This procedure inherently assumes that, first, no electro kinetic (streaming) potential is present, and, second, that the SP is not reduced by resistivity or geometry effects in the formation. When, however, such a reduction of the observed SP does occur, one may write, SP = b,E, b, E, (1) where SP is the observed self-potential opposite the center of the bed under consideration. In this case, E, is the electrochemical potential, E, is the electrokinetic potential, b, is the electrochemical reduction factor, and h, is the electrokinetic reduction factor. The first assumption above is equivalent to assuming E, = O in Eq. 1 and the second assumption is equivalent to h, = b, = 1. Examination of electric logs shows that for many formations of interest the observed SP is reduced below its maximum value. The object of this work is to aid quantitative SP interpretation in at least some of these situations by obtaining values for b, and b, in Eq. 1 as functions of realistic combinations of bed thickness, depth of invasion, and formation resistivity. The only previously published work in this field known to the authors is by H. G. Doll' in 1948. He evaluated b, under conditions permitting exact analytical solution. His work clearly established the importance and qualitative nature of formation geometry and resistivity effects upon the SP, but the necessity of obtaining analytical solutions restricted his study to situations of limited practical interest. In order to extend such studies to practical combinations of formation parameters which do not lend themselves to feasible analytical solutions, the results reported in this paper were obtained by use of a special analog computer. THE ANALOG MODEL The analog model used for this study was the Guyed Analog Computer which originally was designed and built for resistivity log departure curve studies. It consists of a two-dimensional mesh of resistors, with the vertical mesh corresponding linearly to vertical distance along the borehole, and the horizontal mesh corresponding to radial distance from the borehole axis. By proper choice of horizontal resistor values, a three-dimensional, axially symmetric, borehole-formation problem can be modeled with this two-dimensional array. These and other details of the model are contained in a paper by H. Guyod'. The geometry used for the SP studies with the analog is depicted in Fig. 1. This configuration has a horizontal plane of symmetry, and, hence, the model, and the following discussion, need only to be concerned with one quadrant such as shown in Fig. 2. A further simplification arises by considering that both the natural potential sources and those used in the model have fixed internal impedance. Therefore, the current flows produced by these sources can be separated and studied independently ( i.e., the superposition theorem can be applied). SP = SP, i SP, = h,E, + b,E, ,(7)

By C. R. Fast, George C. Howard

Laboratory and field testing of various squeeze cementing techniques and materials revealed that many improvements could be made in squeeze cementing operations. The use of a slow-pumping squeeze cementing procedure permitted the control of the quantity of cement displaced into a formation and aided in obtaining a high final squeeze pressure. Field testing indicated the desirability of obtaining high final squeeze pressures, the need for improved formation breakdown fluids, and the necessity of controlling the pressure differential during testing after a squeeze job. INTRODUCTION During the past few years, squeeze cementing operations have been investigated, both from the theoretical as well as the practical point of view, in an effort to arrive at some solution to the many and varied problems that arise with this type of operation. A review of well files indicated that in many instances, wells were being squeeze cemented four and five times before a satisfactory pressure buildup was obtained. There seemed to be considerable variation in opinion as to the proper method of squeeze cementing, as well as disagreement as to the proper breakdown agent, the quantity of cement that should be used, type retainer and length of WOC* time that was necessary. Consequently, it was deemed advisable to approach this problem theoretically, field testing each idea developed in hopes of eventually arriving at a squeeze cementing procedure that would give reasonable assurance of a successful job after one squeeze cementing operation. This investigation was. therefore, divided into two broad headings: (1) Preliminary studies, which include both theoretical and laboratory studies, and (2) Field investigations to determine the proper squeeze cementing methods. PRELIMINARY STUDIES Overburden Pressure Studies Squeeze cementing problems are so intimately related to the earth's overburden pressure that solutions to them are very difficult, if not impossible, without an understanding of the nature and magnitude of the overburden pressures encountered at the depths of producing wells. It was thus felt that the first approach to research on squeeze cementing should be made through a study of these pressures. Since there has been rather loose usage of a number of the terms related to overburden preasure by different writers, the terms to be subsequently used are defined here. Theoretical overburden pressure is the calculated pressure at any given depth exerted by the theoretical weight of overlying formations as calculated from the average rock density. Fluid displacement pressure is that pressure at which fluid can be injected into a formation after it has been broken down. It may be more or less than the theoretical overburden pressure. Formation breakdown pressure is that pressure at which a formation parts or breaks and is usually thought of as fluid displacement pressure plus rock strength. Breakdown agent is that fluid with which the formation is fractured. The first step in the study of the earth's overburden pressures involved a review of pertinent technical literature. The general opinion expressed was that the overburden pressure gradient of the earth's formations is roughly 1.0 psi per foot of depth, and that application of sufficient pressure to stratified formations. will cause them to part at or parallel to the bedding planes. The second step in the study of overburden pressures involved a study of available well data in an effort to obtain some definite information as to the actual values experienced in the field for the above mentioned terms. Data from 115 cement squeeze jobs in the Gulf Coast area and 46 cement squeeze jobs and acid jobs in the West Texas-New Mexico area were closely analyzed. The analysis of these data showed that the average formation breakdown

Jan 1, 1950

By Adrian C. Dorenfeld, Theodore Balberyszski, Strathmore R. B. Cooke

This paper reports results of studies of sulfidiza-tion of base-metal oxides and silicates with gaseous sulfur, hydrogen sulfide gas and pyrite and of their subsequent flotation with xanthate collectors. It has been established that a 100% conversion of the oxides of lead, zinc, copper and manganese into their respective sulfides is possible and is a function of reaction time and temperature. Sulfidization of chrysocolla (with malachite and azurite inclusions) resulted in a product containing covellite, chalcocite and digenite in proportions depending on conditions of sulfidization. Reacting cassiterite with gaseous sulfur, H2S or pyrite at various reaction temperatures resulted in its partial conversion to a tin sulfide. Flotation of the products of sulfidization indicated that their behavior is similar to that of natural sulfide minerals, the recovery being a function of the con-version of the oxides to their respective sulfides. The gradual depletion of high-grade sulfide mineral deposits has turned the attention of the mineral industry to the recovery of metals from the oxides and silicates. Anionic (fatty acid) and cationic collectors have in some cases made flotation of nonsulfides possible, although, in general, flotation of oxide ores is not as yet an economic process. Consequently, many attempts have been made to sulfidize the surface of the relevant oxide mineral and thus make it amenable to to In recent years, Bautista and sollenberger4 have investigated the conversion of a number of oxides to sulfides by reacting them with molten sulfur. This paper presents the results of .investigations carried out at the School of Mineral and Metallurgical Engineering at the University of Minnesota to study the flotation characteristics of some sulfidized minerals. It is divided into two parts: The first describes the sulfidization of a number of oxides and a silicate, and the second presents the flotation behavior of the products of sulfidization. SULFIDIZATION OF METAL OXIDES AND SILICATES Experimental Procedure: SULFIDIZATION WITH HYDROGEN SULFIDE GAS — Sulfidization with H2S gas was carried out in a horizontal tube furnace (Fig. 1). The temperature of the furnace was regulated by means of a Variac and determined with a chromel-alumel thermocouple. The constant temperature zone in the furnace was about 6 in. in length, and it was within this zone that the experiments were carried out. The gases employed were supplied from standard compressed gas cylinders, and passed through a glass-wool filtering tower before entering the Pyrex reaction tube. Gaseous products were bubbled through a water tower (used as a flow indicator) and excess H2S was burned off at the end of the outlet tube. Samples of reagents or minerals were placed in a 3-in. Alundum boat and inserted within the constant temperature zone of the furnace. Nitrogen gas (6 ppm O2 content) was passed through the tubes at room temperature to remove air in the tube, and continued to pass while the furnace was heating up. When the required temperature was reached, H2S was allowed to enter the tube and the supply of nitrogen was shut off. At the end of the reaction period, the reverse procedure was carried out, the samples being cooled to room temperature in a nitrogen atmosphere. The flow rate of H2S gas was maintained fairly constant in all experiments, although the rate was not determined. SULFIDIZATION WITH SULFUR POWDER - To study the sulfidization of minerals with sulfur (liquid or gaseous), samples of the mineral, together with a measured quantity of sulfur powder, were placed in a stainless steel (SS316) reaction vessel (Fig. 2). The reaction vessel was heated in a vertical resistance coil furnace, the temperature being regulated through a Variac. At the end of the experiment the vessel was cooled to room temperature before the sample was removed. Cooled products were leached with CS2 to remove any free sulfur. SULFIDIZATION OF TIN CONCENTRATES - Fifty gram samples of sulfidized tin ore were prepared by mixing -48 mesh Bolivian tin concentrate with -48 mesh Ottawa sand in various proportions and sulfi-dizing these samples with H2S in the horizontal tube

Jan 1, 1969

By John C. Draper

The principal object of an underground coal mine transportation sys tem is to move coal from the face where it is produced to the outside of the mine where it is prepared for market. In addition to the movement of coal, a transportation system must also move supply materials to the inside; it must move men in and out of the mine ; and it must move rock and other debris out of the mine for disposal. Usually, mine haulage is divided into three categories named for the various areas of the mine served: 1) Face Haulage. This is used at face from the mining machine to the intermediate transport system. 2) Intermediate or Secondary Haulage. Generally this is used between face haulage and main haulage. Sometimes this is merely an extension of the main haulage. 3) Main Haulage. This extends from the secondary haulage to the outside and is usually either a track or conveyor system, sometimes a combination of both. Transportation modes of coal in the various areas pose different problems, but the whole system must be synchronized. For instance, at the face the coal should be removed quickly from the various places to facilitate the movement of machines, whereas the intermediate system just passes the same coal on to the main transportation system. Selection of the transportation system must be based on the seam height, mining methods used to extract the coal, capacity required, ease of coal handling, and haulage efficiency. When driving rooms, mine cars can be used. They often simplify supply haulage and rock handling because they can also handle these items. Conveyors could be used and would have a greater haulage capacity but they cannot handle supplies easily or segregate the rock. When using a different mining method, such as longwall, mine cars cannot be used because there is not sufficient space to move the cars at the face nor can the cars haul the coal without delays which would cause excessive losses in production. As for ease of handling

Jan 1, 1973

By K. R. Janowski, H. Conrad

As part of a program to establish the effect of crystal imperfections on laser output, a detailed study was made of the dislocation structure of ruby crystals obtained from varioius sources. Using KHSO4 as an etchant, a detailed mapping of the dislocation structure on the (0001) and the (1150) planes was carried out. A less extensive study was made of the rhombohedral planes. The average dislocation density on the basal plane was 1.5 to 3 x 106 cm&apos;2 and on the (1120) planes -5 x 10&apos; cm-2. Howe7!er, considerable variation existed between areas on a given plane. The subboundaries in the basal plane tended to lie along [1100] type directions while those on the (1120) plane tended to lie: a) parallel to the basal plane, b) along truces of the (1101) plane, and c) along normals to the traces of the (0001) planes. The orientations suggest that mang of the dislocations lie on the (0001), (1701), and (1150) planes A Laue back-rellection nnalysis Of c-axis wander in one crystal revealed a gradual increase in misorientation from me end of the crystal to the other, with a maximum variation of 1°35&apos;. Slight etching of a mechanically polished crystal revealed mumerous polishing scratches, suggesting the existence of a plastic flow layer. It is recognized that chromium concentration, lineage, and other crystalline imperfections play a role in the efficiency of ruby lasers.&apos; Consequently, it is desirable to establish in detail the imperfection structure of ruby crystals to be used as lasers. Some exploratory work along this line had already been done by Barnes&apos; and Dils and Martin.&apos;" How- referred to as the morphological system, as described by Kronberg.4 The Miller indices given in the present paper will be based on this morphological system. In this system, the three common growth planes are the (0001), the {1120}, and the {1101}.5 Since these planes are of high stability, it is expected that they are most suitable for study by the etch-pit technique. In the present investigation, a detailed mapping of the dislocation structure was carried out for the (0001) and the (1130) planes. A less extensive study was made of the etch-pit structure on rhombohedra1 planes. An analysis of dislocations in sapphire (the ruby host) was first made by kronberg,4 who postulated that slip on the (0001) plane occurred by motion of dislocations with Burgers vector 1/3 <1150> and that these dislocations might dissociate into quarter partials. An etch-pit technique using boiling phosphoric acid was developed by Scheuplein and Gibbs6, 7 for identifying dislocations intersecting the (0001) planes and the planes near (2021) in sapphire. Al-ford and Stephens8 were able to reveal dislocations on the (0001) and {1120} planes in sapphire and ruby by etching in fused potassium bisulfate (KHS04) at 675°C. The termini of basal dislocations [(000l), <1120>] were revealed by Palmour and Kriegel9 on {1120} and {1010} by thermally etching sapphire. Bond and Harvey10 were able to decorate dislocations in sapphire by adding 1 pet by weight of ZrO2 to the Al2O3 powder used in the growth of the crystals by the Verneuil technique and then heating the grown crystals for 4 hr at 1500°C. They found, using optical transmission microscopy, that many dislocations had straight segments which were parallel to one of the six [1120] directions in the basal plane. Single dislocation lines curved smoothly from one alignment to the other, turning through angles of 60 to 120 deg. Also observed were isolated hexagonal loops, approximately 10 µ in diameter, the sides of which lay along the same directions as did the longer dislocations. MATERIAL AND ETCHING PROCEDURE The ruby specimens used in this study (all containing approximately 0.04 pet Cr) had been obtained from four different sources: Linde Co., Meller Co., Valpey Crystal Corp., and those grown at Aerospace Corp.* For the initial phase of this study, several specimens were cut from the slab shown schematically in Fig. 1 which had previously been cut from a disk boule obtained from the Linde

Jan 1, 1964

Mount Isa Mines&apos; Hilton Mine was brought into large-scale production in 1990/91 at a time of sharply falling metal prices. To ensure the operation&apos;s survival and eventual prosperity there was an urgent need to reduce operating costs and increase revenue. A target of a 40 per cent increase in productivity over five years was set. Strategies to obtain the required improvements were developed on the basis of greater involvement and increased contribution from the workforce, major changes to the mining methods and the development and application of new technology. This paper describes the organisational, operational and technological changes that have been implemented at Hilton and presents the results achieved to-date.

Jan 1, 1993

By J. E. Fox Jr., J. L. Lummus, J. P. Gallus

Fresh water or brine drilling fluids may be kept free of suspended drilled solids by the addition of a water soluble acrylamide-carboxylic acid copolymer at the flowline. Addition of from .01 to 0.2 lblbbl of the polymer solution to drilling fluids containing less than 5 per cent clay solids by weight causes the solids to flocculate and settle rapidly to the bottom of the pits. Solutions of the polymer injected at the pump suction reduce the loss of water to permeable formations without impairing the permeability to oil. The use of drill-itlg fluids clarified with the polymer has resulted in increased drilling rates, extended bit life, and lower drilling fluid costs. INTRODUCTION Field experience and the results of a number of investigations have established that the accumulation of solids in drilling fluid reduces drilling rate.&apos;-&apos; Drilling with water makes possible higher drilling rates than can be achieved with mud but in many areas drilling with water may not be feasible because of the possibility of encountering high formation pressures or by-dratable formations. To combat these conditions, the drilling fluid must possess certain physical properties such as viscosity, density, fluid loss, etc., which require the presence of solids. The current trend in drilling fluid treatment is to maintain as low a percentage of solids as is possible without harmfully affecting the mud properties needed for drilling. Mechanical separating devices such as wet cyclones and decanting-type centrifuges are proving to be an economical means of controlling the percentage of solids and thereby maintaining low solids muds. Also: special muds have been developed for the purpose of retarding the hydration of drilled solids so that they may be more easily removed by shale shakers or settling pits. In some areas, such as West Texas, the characteristics of some formations will permit drilling with water. However, because of the dispersion of drilled solids, it is usually not possible to maintain clear water even with the aid of mechanical separators, or by utilizing large settling pits. For this reason the commonly used term "water drilling" is a misnomer since the water usually contains some solids. Because of the improved drilling rates and other benefits which might be effected, a laboratory and field study was made of the use of flocculating agents for maintaining clear water for drilling. PROCEDURE Laboratory—Solids Settling Two techniques were employed to determine the effectiveness of flocculating agents in settling solids from drilling mud. First, the rate of fall of solids was measured in graduated beakers containing mud treated with various flocculating agents. Natural gum, oil-in-water emulsions prepared with ethoxylated nonyl phenols and diesel oil. and a powdered synthetic acrylamide-carboxylic acid copolymer* (hereinafter referred to as "polymer") were tested as flocculating agents in both fresh water and salt saturated muds containing 4 per cent solids. The polymer was not added in the powder form directly to the muds but was first dissolved in water in a concentration of 3.5 lb/bbl. The polymer solution was then added directly to the mud. The concentration of the flocculating agents, including the polymer, was varied. High rates of fall of the solids indicated high flocculating efficiency. A second technique consisted of measuring the time in minutes required to obtain clear water at the pump suction after addition of the various flocculating agents at the flowline. These tests were made using a model mud circulating system having a total volume of approximately 10 gal. The natural fresh water and brine muds used contained 4 per cent solids. A sketch of the circulating system appears in Fig. 1. The circulating rate

By C. Zener, J. H. Hollomon

IT Is commonly recognized that a given material may be described as ductile or brittle only with reference to the conditions of test. Thus under the usual test conditions quartz is brittle, but under high pressures it is ductile. Salts that are brittle at room temperature become ductile at elevated temperatures. Pitch, brittle with respect o rapid loads, flows at low rates of loading. Pearlitic steel, ductile under the usual conditions of test, may be embrittled under the proper conditions of combined stresses, temperature, and rate of loading. EARLIER INVESTIGATIONS A clear analysis of the conditions necessary for plastic flow and for fracture was first given by Ludwik,1 who introduced two types of stress, the "flow stress" and the "stress at fracture." These stresses may refer to tensile or to shear stresses, or, in fact, to any type of stress. Ludwik considered these two stresses to be independent of one another, functions of the conditions of test and of the prior history of the material. For the purpose of analysis, both a flow stress and a stress at fracture can be envisaged as functions of strain over the entire range from zero to infinite strain. Thus, the material is brittle if the stress at fracture is less than the flow stress and ductile if the reverse is true. According to Ludwik&apos;s analysis, the problem of determining the effects of combined stresses, of temperature and of strain rate upon the behavior of metals reduces to a problem of determining the effect of these variables upon the flow stress and upon the stress at fracture. In the present paper, methods are described for determining the effects of two of these variables, temperature and strain rate, and examples are given of the dependence or now stress and stress at fracture, upon these two variables. The effect of combined stresses will be discussed in a succeeding paper. The flow stress may be determined from a load-diameter curve. Load-diameter curves were obtained over a wide range of temperature and over the limited range of strain rates obtainable with the lever-type Riehle machine used. The. curves were then converted to an extremely wide range of strain rate by making use of the equivalence of the effects of changes in strain rate and changes in temperature, previously proposed2 and demonstrated&apos; by the authors. According to this principle of equivalence, strain rate E and temperature T affect the flow stress only through a single parameter p of the form: p = EeQ/RT [I] In this equation, R is the gas constant (2 cal. per gram mol per deg. C.), and Q is a heat of activation, which varies from material to material, and may depend upon the strain, but not upon the strain rate or the temperature. There is associated with every value of p a flow-stress curve. Combinations of strain rate and of temperature that give the same p have the same flow-stress curve. Therefore, merely by changing the temperature of test, the effect of changing the strain rate may be obtained. Thus, under isothermal conditions, the material will behave the same at

Jan 1, 1944

By K. Adham, T. Buchholz

"Significant capacity increases to meet new production demands can often be fulfilled through debottlenecking of an existing production facility, rather than the more expensive option of building new plants and facing new environmental and infrastructure challenges. To achieve that goal, it is important to model and calculate the existing ultimate capacity of each processing plant area, and that of each key equipment sector within the plant areas. This paper describes a methodology of how process modeling tools can be used to simulate the processing steps, how to estimate their existing and ultimate capacities, and how to determine the sweet-spots (minimum cost points) for a plant expansion – leading to a road map of the subsequent debottlenecking project implementation.The debottlenecking technique is presented through a generic work-flow narrative which can be applied to different mineral processing studies, starting with establishment of heat-and-mass balances, drawing a bottleneck diagram, brainstorming capacity increase options, and preparing a cost-capacity curve. Hatch has successfully applied this technique to a number of plant capacity studies, with great benefits to our industrial clients.INTRODUCTIONWith the softening of the metals and minerals prices, and the escalated costs of building new processing plants, it is now economically more viable to improve and debottleneck the existing facilities, rather than build new ones. However, spending new money on old plants requires careful considerations, in order to identify the most economically advantageous incremental steps of improvement and the best potential returns on investment. Process modeling, hand in hand with plant measurements, can identify the best scenarios to balance the three aspects of plant capacity (nameplate, utilization and yield), both at the global and the individual system and subsystem levels."

Jan 1, 2016

By R. W. Shearman, F. Weston Starratt

A new center for mining and metallurgical research is developing at Sterling Forest, N. Y., under the auspices of Union Carbide Corp. Here is to be located the Union Carbide Nuclear and Ore Research Laboratories. In truth, history has repeated itself; the Sterling Forest area in the days of the Revolutionary War, and for many years thereafter, was the mining and metallurgical center of the US. For in these Ramapo hills along the New York-New Jersey border, iron ore was mined, pig lion was cast, and the weapons of war and the plowshares of peace were forged. Before embarking on an historical pilgrimage to yesteryear-a brief description of Sterling Forest. Located in Orange County, N. Y., near Tuxedo, immediately north of the New York-New Jersey State line, and just west of the Erie Railroad and the New York State Thruway, Sterling Forest is approximately 35 mi from New York City. Title was acquired in 1956 from the Harriman family by City Investing Co. Its President, Robert W. Dowling, has established himself as a city planner, having conceived such projects as Pittsburgh&apos;s Gateway Center and Philadelphia&apos;s Penn Center. A unique, self-contained community -is planned that will contain light industry and centers for research and engineering. Colonies of homes will be interspersed throughout the 20,000 acres of forest land, lakes, and rolling hills. Culture will not be neglected, for Sterling Forest will be the new home for the annual Empire State Music Festival The Sterling Forest Gardens, 125 acres of landscaped woodland and streams, will become the "world&apos;s largest permanent floral showplace" The Sterling Forest International Research Building was opened earlier this year, and designed to provide all facilities needed by small growth research companies. The first major company to acquire land to construct research buildings at Sterling Forest is Union Carbide. 1763 ... Discovery of iron ore In turning back the pages of history, a fascinating story can be told of special interest to the metallurgist, the mining engineer, and perhaps even the sociologist. For, where new communities are planned today, older communities had been born, matured, and died. In these hills had lived the. iron miners, the blacksmiths, the lumbermen, the masons, and the teamsters that had given America its start in heavy industry. This was the area where the forests were crisscrossed with many wood roads that brought logs to the charcoal pits, and iron ore to the furnaces. Men make history. Our story brings forth many names of men known as ironmasters, or as industrial leaders-Hasenclever, Faesch, Erskine, Townsend, Ryerson, Parrott, Cooper, Hewitt, Jay Cooke, and Harriman. The name Sterling is derived from a Scotch Lord, the Fifth Earl of Stirling (in its earlier spelling). Lord Stirling was one of seven Englishmen granted a patent of land in the Ramapo hills by Queen Anne in 1707, known as the Cheesecock Patent. He sent an agent, Cornelius Board, to America in 1730, with the express purpose of looking for copper deposits. While he found no copper in his travels up and down the Ramapo Valley, he did find iron ore in two localities: first, in the vicinity of what is now Ringwood, N. J.; second, five miles to the north. There he constructed a forge and furnace at the edge of a lake in 1736, naming the land Stirling Property, after his patron. In 1740, the Ogden family in Newark bought land from Board at Ringwood and began smelting of iron in 1741. The Ringwood story Soon, a genius in the person of Peter Hasenclever appeared on the scene. He was attracted by an advertisement in the New York Mercury for March 5, 1764, in which David Ogden of Newark offered

Jan 1, 1961

By Lee Hillard Meltzer, Ralph E. Davis

INTRODUCTION During the past few years emphasis has been placed upon methods of estimating the future expectancy of gas production from natural gas fields. Before technical methods were applied, the production expectancy over future years was based upon the knowledge of gas well behavior, learned through long experience and embedded in the "know-how" of men long in the gas producing business. It is doubtful that a technical study of future expectancy of a gas field or a group of fields was ever prepared for the preliminary planning of a natural gas pipe line system built prior to about five years ago. The decline in well production capacity was naturally recognized by all familiar with the business since its earliest beginnings more than 75 years ago. In 1953, the Bureau of Mines published Monograph Number 7, "Back-Pressure Data on Natural Gas Wells and Their Application to Production Practices," which gave to the industry the first technical analysis of the decline in production of individual gas wells. This method affords a means of estimating the future production in relation to decline in reservoir pressure. The demand for technical determination of expectancy of future gas productivity from fields or a group of fields led technical men to the application of the knowledge of well behavior to the problems. The decline in a well&apos;s ability to produce as pressures declined could be estimated by the use of the curve known as the "back-pressure potential curve" as developed by the Bureau of Mines. A field containing few, or even numerous, wells could be analyzed on the basis of the sum of potentials of all wells. In most studies of this nature, the problem is to estimate the rate of production that can be expected, not only from present wells but also, from wells that will in the future have to be drilled into the reservoir being studied. The "back-pressure potential" method requires that the following data be known or estimated: (1) Proved gas reserves. (2) Current shut-in pressures and rate at which shut-in pressures change with production. (3) Back pressure potential data on wells in the source of supply. (4) Ultimate number of wells which will supply gas, and their potential. (5) Limitations on productivity such as line pressures against which the wells will produce, friction drop in the producing string, and so forth. It is evident that the resulting estimate of gas available in each year for a future of say, 20 years, contains many uncertainties. While the method may have considerable merit for a field that is fully developed, it cannot be completely dependable in fields that are only partially developed. In such cases, some of the data upon which it is based can only be estimated or assumed. In the study of this problem during the past few years, a method has been developed which we believe has great merit, especially when applied to fields subject to substantial future drilling, and when applied to the study of fields which, on the average, appear to have characteristics similar, in general, to the average of the fields used in the development of the "yardstick" outlined herein. From an analysis of the production history of 49 reservoirs which are depleted, or nearly depleted, a curve has been constructed which shows the average performance of the reservoirs during the declining stages of production. When properly applied, this "average performance curve" can be used to determine the stage of depletion at which a reservoir or group of reservoirs will no longer be able to yield a given percentage of the original reserves. "AVAILABILITY" AND "AVAILABILITY STUDIES" The rate at which. a reservoir will yield its gas depends basically upon physical factors, such as the thickness and permeability of the sand, the effect of water drive, if any, and other conditions, and upon economic factors, such as the number of wells drilled. Within the ranges set by the physical conditions, a rate of delivery tends finally to become established. The rate (or range of rates) represents a balance between the interests of the operator, who desires the maximum return from his property and of the pipe line owner, who desires to maintain a firm supply for his market. This balance, which is influenced by the terms of the contract, determines the capacity which will be developed by the operator, and the time and rate at which the decline in production is permitted to occur. Thus the "availability" of gas

Jan 1, 1953

By Liu Y

Ventilation, air leakage, and various cutting, loading and support movement operations all have a role in dust distribution on longwall faces as shown by the results of a large number of dust measurements on different longwall operations in the Bulli seam on the South Coast. It is concluded that leakage of air on the face has demonstrable mfluence on the exposure of the shearer operator to dust level. It is possible to calculate dust generated by various elements of a rrurung operation on the face from a single point measurement. In the examination of dust deposition from the source of generation as a function of particle size, it is found that respirable dust can remain airborne over long distances without any significant drop in concentration, if unobstructed.

Jan 1, 1995

By Richard H. Hopkins, R. W. Kraft

A new technique facilitating the rapid determination of the three-dimensional morphology of phases suspended in an opaque matrix is described. The vapidity of the technique is based upon continuous cinephotomicrographic recording of specimen microstructure as the specimen surface is removed under controlled conditions in an electrolytic cell. The advantages of the technique for determining spatial morphologies in opaque materials are illustrated by application of this method to the study of the configuration of faults in a specimen of directionally solidified CuAl2-Al eutectic alloy. A spatial model of the eutectic fault network deduced in this manner has substantiated the facts that faults in this alloy tend to lie parallel to one another in a direction close to that of the specimen growth axis and that the majority of faults tend to bridge lamellae rather than run parallel to them as growth proceeds. For the specimen studied fault density decreased as growth proceeded. ALTHOUGH metallographic observation is a powerful tool for investigating the correlation between structure and properties in metallic alloys, ordinary metallographic methods suffer the fundamental limitation that any conclusions concerning the three-dimensional structure of these opaque materials must rely upon inference from two-dimensional microsections. For this reason it is frequently impossible to make valid judgments regarding the true spatial distribution of the micro-constituents in specimens under investigation. Several techniques have been devised to circumvent the basic limitation of planar microsec-tioning and employed with varying success. These include construction of three-dimensional models of alloy microstructure from sequences of photomicrographs,1-3 quantitative deduction of spatial features based upon statistical studies of data from random and/or selected plane microsections,4-6 and selective dissolution of one phase in a two-phase alloy to reveal the topography of the phase remaining.&apos; However these techniques also have certain obvious disadvantages. Construction of three-dimensional models is a very time-con- suming procedure due to the tedious polish-etch-photograph cycle needed to obtain the necessary photomicrographs to portray the spatial microstructure. Statistical methods by their very nature give only average values of the quantities being studied and cannot therefore give a detailed physical picture of the microstructure to be observed. Finally, the technique of selective dissolution is only applicable in systems where the phases are of vastly different chemical reactivity; it is of little use in the study of single-phase alloys. Since the determination of the three-dimensional structure of opaque materials is hindered by two facts—the materials are opaque to radiation in the visible spectrum and construction of spatial models of microstructure is quite laborious—two solutions to the problem suggest themselves: 1) use radiation of energy great enough to render the alloy transparent, i.e., some microradio-graphic method, or, 2) devise a rapid means to section and record alloy microstructure. Stereomicroradiography has indeed been used to study internal arrangements of phases in several materials8,9 but the method, in general, is limited to very thin specimens (due to X-ray absorption) and simple microstructures. It would seem then that development of a rapid, simple, and generally applicable technique for studying the details of alloy microstructures in three dimensions can best be undertaken by following the second approach above. Using this idea a new technique for rapid evaluation of spatial microstructures was developed based upon cinephotomicrographic recording of the micro-structure of a specimen undergoing controlled electrolytic dissolution. It was further felt that application of this technique to the careful study of the spatial configuration of faults in a CuAl2-Al eutectic alloy would yield information that could be correlated with the extensive data3,6,10-12 already compiled concerning the solidification and crystallography of this eutectic. The practicality and usefulness of similar methods for studying three-dimensional features in alloys has recently been illustrated by the study of dislocation loops in zinc13 and spheroidized structure in steel.14

Jan 1, 1965