Search Documents

By Henry Mulryan

THE largest and purest known deposit of diatomite is being actively mined and processed 3 ½ miles south of Lompoc, Santa Barbara County, Calif., by the Johns-Manville Products Corporation. The workings FIG. 1-LOCATION OF DIATOMITE DEPOSIT AT LOMPOC. cover 4000 acres, the depth of economically recoverable diatomite being 1000 ft. (Fig. 1). Lompoc, a community of 2500 population, is situated in the Santa Ynez River Valley 10 miles inland from the Pacific Ocean. It is 44 miles

Jan 1, 1936

By Jennifer Peirce Brandt

Project documents and the United States Army Corps of Engineers? permit for construction of the Stemmers Run Relief Wastewater Force Main across the Back River in Baltimore County, Maryland specified a minimal width, steel sheet pile cofferdam and a 12 feet wide, pile supported, timber decked, causeway trestle ? both approximately 1700 feet in length. Due to the impractical width of the causeway, the contractor desired to combine the cofferdam and the causeway structures in order to minimize wetland disturbance and maximize access for construction equipment. The resulting support structure was a steel sheet pile cofferdam, approximately 17 feet wide, internally braced, and capped with transverse timber deck mats to serve as the access and work trestle for the trench excavation, pipe bent construction, and trench backfill. Construction of this cofferdam/causeway progressed from the north shoreline toward the middle of the river. Then, working back toward the north shoreline, the contractor excavated, installed the 54 inch diameter pipe and H-pile support bents, and backfilled the trench in increments of approximately 60 linear feet. Excavation spoils from one section were used to backfill the preceding section. As the pipe installation progressed toward the north shore, the steel sheet piling and timber deck were removed. As sufficient sheet piling and deck mats were removed, the contractor began the process anew from the opposite shoreline using the reclaimed materials. The project was complicated by the presence of deep, very soft, weight of hammer, silts and organic clays and an unbalanced, hydrostatic head of 20.5 feet. In addition, concurrent pile driving, excavating, and backfilling in successive cofferdam sections required the use of heavy, long reach, hydraulic backhoes, and a 200 ton capacity crawler crane which controlled the design of the timber causeway deck and its supporting sheet piles.

Jan 1, 2008

By Bertha Farfán del Carpio Vera

En este resumen se presenta los estudios iniciales que nos permitirán descubrir nuevas propiedades de estos 2 elementos, al ser transformados en áridos livianos, cuando luego de un proceso de precipitación química y a través de la catálisis heterogénea, son depositados en una sustancia de soporte conocida como zeolita clinoptilolita. Ambos metales Pb y Zn, adhieren totalmente a la zeolita, la cual se comporta como un catalizador metálico dispersado, siendo los metales Pb y Zn, los que se depositan sobre la anterior pasta para formar los pellets.Luego de mezclarse completamente, el soporte y el material catalítico se compactan, se someten a un proceso de extrusión.

Sep 1, 2017

By N McIntyre, M Edraki, K R. Jain

From the very early stages of a mining project, there is a requirement to predict the chemistry of potential drainages from various waste storage facilities. However, using relative masses to scale chemical loads measured by laboratory kinetic tests, such as humidity cells, to a full-scale mine waste facility will lead to concentration predictions that are unrealistically high for many dissolved constituents. Scaling factors developed by various procedures indicate that laboratory rates may range anywhere from two to eight times (Drever and Clow, 1995) to 100 to 1000 times faster than field rates (Malmstrom et al, 2000; Smith and Beckie, 2003; Ritchie, 1994). This contribution will use previous works and secondary data to discuss the significance of scale in water quality predictions. It will also present primary experimental geochemical and numerical data from a column leaching study on coal spoils to discuss potential applications of mesoscale leaching tests in bridging the gap between bench-top tests and field scale trials.

Aug 2, 2023

By K. L. Morton

This technical note reviews the status quo of mud rushes and flooding, which have claimed them lives of many people in underground mines in South Africa and globally. Given that the causes are well known and can be managed, the note calls for the development of a national and global standard on flood and mud rush prevention in order to save lives.

Mar 30, 2026

By N. R. Ayupova

Several metallogenic zones including Sakmara, Magnitogorsk, and East-Ural zones were revealed in the Ural fold belt (Fig. 1). These zones are considered to be the paleogeodinamic sectors corresponding to marginal sea, island arc system, and uplift respectively. Ferruginous-manganiferous sediments in the Southern Urals are hosted by the basalt-rich volcano-sedimentary series of the Magnitogorsk paleoisland arc system with West- and East Magnitogorsk island arcs and Sibai inter-arc basin. The manganiferous mineralization occurs in association with the Middle Devonian stratabound hematite-quartz rocks and bedded red jaspers localized on the foot or handing walls of massive sulfide deposits. Fe-Mn nodules are widespread in jasper horizons on the flanks of manganese deposits. We have studied Fe-Mn nodules from the Faizulino and Yanzigitovo Mn-deposits formed in the Sibai inter-arc basin and compared them with well known Fe-Mn nodules from modern oceans.

Jan 1, 2010

By M. M. Tilman

The Bureau of Mines conducted research to evaluate superplastic behavior in commercial magnesium-base alloys AZ6IA, ZK60A, ZW3, AZ3IB, ZWI, and an experimental Mg-12 pct Al alloy. Strain-rate sensitivity indices (m-values), maximum elongations, and effects of superplastic elongation on tensile properties were determined on fine-grained sheet. Inert-gas-pressure hemisphere-forming tests were conducted on selected sheet stock of the five alloys. Formability trials on AZ31B alloy sheet were conducted on industrial equipment for comparison with commercial superplastic forming of Zn-AI alloy. Closed-die-forming tests were performed on extruded ZK60A rod. All alloys exhibited well over 100-pct elongation, indicating superplasticity, at temperatures and strain rates near the maximum m-values. Tensile properties were generally reduced following 100-pct superplastic elongation, but not to an extent that would preclude use of the commercial alloys in the superplastically deformed condition. The potential for industrial superplastic forming of AZ31B sheet was indicated by hemisphere forming in the laboratory and substantiated in industrial forming trials.

Jan 1, 1982

By W. G. Davenport

The Cu content of industrial flash furnace concentrates varies considerably. It is usually around 30% Cu (Tables 2.1, 3.1) but it may be as high as 55% Cu and as low as 20% Cu. The mineralogy of flash furnace concentrates also varies. The most common Cu mineral is chalcopyrite (CuFeSz), but many concentrates contain bornite (CuSFeS4), chalcocite (CU2S), covellite (CuS) and even native copper (CUO). Pyrite (FeSz) :is also present in many concentrates. This chapter examines how concentrate composition affects flash smelting -with specific reference to 'low-Cu-grade' FeS2-CuFeSz concentrates. Chapter 14 does the same with 'high-Cu-grade' CuzS-CuFeSz?concentrates.

Jan 1, 2001

By Li Shanqing, Xu Jianghua, Li Hongmei, Huang Peijie

Cold rolled high strength steel are playing a very important role in reducing automobile weight for energy saving and environment protection. In recent year, more and more high strength steel were manufacturing in steel company. But there are some problems in the cold rolling process for high strength steel products. Periodic thickness deviation especially in strip head or tail is an important one in these problems. In this paper, the reason of periodic thickness deviation was analysed and a new AGC algorithm called Property FFC for high strength steel in tandem cold rolling was developed. The application of this new algorithm shows that it can reduce the thickness deviation.

Oct 1, 2019

By G. B. Shea

In 192b, there wore 47 fatal accidents in the California petroleum industry, 14.6 per cent more than occurred in 1927 when 41 men lost their lives in the drilling, producing, manufacturing, and marketing divisions of the industry. This increase in the number of fatal accidents for 1928 has caused the first upward trend in the fatality curve of the California petroleum industry since 1923. In no other year during the 6-year period have the fatalities in any one year been greater than those for the preceding year. This fact should be given serious consideration and study by the petroleum industry, and an endeavor should be made to cause the number of fatalities again to decrease and conform to the previous gradual declining trend of the fatality curve. The following chart shows the trend of fatal accidents during the past six years:

Jan 1, 1929

By S. J. Hemberger, F. W. Lee, J. H. Swatz

"INTRODUCTION This investigation was undertaken in 1939 for the purpose of securing the necessary information relating to the field techniques and accuracy that would be needed for magnetically surveying State-wide areas. The Florida,peninsula was chosen for such a study for two reasons: First, because it is geologically ideal for such an investigation, since it comprises a series of unconsolidated, flat-lying Tertiary and Cretaceous sediments of low magnetic susceptibility covering a complex and much-folded crystalline basement comprised of rocks carrying strongly -paramagnetic materials; second, because information concerning the structural trends of the crystalline basement would be of great interest and Importance in the study of Appalachian orogeny and the relationship of the Florida Peninsula to both the Appalachian and Antilleantectonte systems. The results of this magnetic survey have clearly demonstrated that the magnetic anomalies reflect variations in the crystalline a basement. To the degree which the structures of the crystalline basement control the structures of the overlying sediments these results are useful for oil exploration.MAGNETIC OBSERVATIONSAll magnetic measurements were made with a vertical Aekania magnetic variometer having a temperature compensated needle. All observations were tied into two base stations located at Fort. Myers and Gaineeville, Fla. The absolute vertical magnetic intensities at these two bass stations were determined by the United States Coast and Geodetic Survey within an accuracy of + 10 gammas. The accuracy of the base station variometer used in the present survey was of the order of ± 3 gammas. The sensitivity throughout the survey of the magnetic variemoter used on the traverses approximated 30 gammas per scale division and it is estimated that the probable error between stations along a traverse would be about + 5 gammas. Measurements were started on traverse C near Fort Myers and tied into the Fort Myers base station established by the Coast and Geodetic Survey. Twelve traverses, comprising 1,500 station observations, wore occupied between the Fort Myers and Gainsville base stations. When the cumulative total of these 1,500 interim observations was tied into the Gainesville base station it was found to differ by only 30 gammas from the value obtained by the Coast and Geodetic Survey for that base. The observations were adjusted for this difference."

May 1, 1945

By J. R. Nettle

A method has been developed in the laboratory for successfully electro-refining titanium metal. Refining is accomplished in e fused-salt electrolyte using offgrade metal as the anode and collecting the purified metal at the cathode. The characteristics and requirements of the various alkali chlorides tested as electrolytes are discussed in relation to relative ease of purification and serviceability. The various types of cells designed and tested for electrorefining are illustrated and their method of operation discussed. The individual advantage of each cell and the purpose for which it was designed are reviewed. The magnitude of the cathode current density was found to depend largely upon the quantity of soluble titanium chloride in the electrolyte. The physical condition of the anode also greatly affected the cathode current density.

Jan 1, 1957

By Richard G. Almes

Since the failure of a major coal refuse disposal embankment and impoundment in the Buffalo Creek watershed near Man, West Virginia in early 1972, there have been extensive changes in the design and construction requirements for coal refuse disposal facilities located throughout the United States. The primary emphasis has been on improving the safety of these facilities, particularly for impoundments which are capable of storing millions of gallons of process water and storm runoff. The Mine Safety and Health Administration (MSHA) of the U.S. Department of Labor (formerly the Mining Enforcement and Safety Administration, U.S. Department of interior) has been the lead federal agency in promulgating regulations pertaining to coal waste disposal. In 1974 and 1975, studies were undertaken by our firm under contract to the Mining Enforcement and Safety Administration to prepare a comprehensive engineering and design manual to be used by operators and engineers in the planning and design of coal refuse disposal facilities with the intent ion of avoiding any more Buffalo Creek failures. The resultant 800-page document addresses major subjects such as safety, environmental controls, and cost. Specific topics include characterization of coal refuse, classification of disposal facilities, project planning, geotechnical investigations, testing and design requirements, hydraulic and hydrologic design, environmental factors, operations, and monitoring, instrumentation, and maintenance.

Jan 1, 1980

By Robert L. Frantz

The various facets of university-company cooperative activities and the opportunities for collaborative research for the mineral industries are presented in this paper. The advantages and disadvantages of various alternative research funding arrangements for the researcher, the university, and the sponsoring corporation are discussed. Examples of university-industry cooperative research programs are briefly outlined. The concept of a cooperative mining research program is presented. The improvement of performance through techno- logical developments and human skills may well be the greatest competitive edge available to the U.S. mining industry. In this regard, the need for new endeavors between industry and universities can hardly be overemphasized.

Jan 1, 1984

By F. G. Miller

Over the past 30 years, the coal industry has been continually striving to perfect methods for cleaning fine coal to acceptable ash and sulfur contents while maintaining maximum product yield. The flotation process has been part of this effort and its importance is expected to grow as new utilization technology demands finer and purer coal products. The work outlined in this paper is part of a larger effort aimed at development of new and improved flotation systems for removing sulfur and ash from as-mined coal as well as for producing super-clean coal for future markets. The concepts and data presented are now serving as a basis for designing fine-coal circuits in which improved efficiency is obtained by optimum use of flotation.

Jan 1, 1986

By Leonard Obert

THIS REPORT presents methods and principles useful in designing underground mine openings and pillars in competent rock formations. Two types of formations are considered: (1) Massive formations, in which openings are generally mined with an arched roof, and (2) bedded formations, in which openings are generally mined with a flat roof. Design principles for openings and pillars in massive formations are obtained by considering the maximum tangential stresses developed around single and multiple openings for stress fields of various types. Design principles for openings and pillars in bedded formations are obtained by considering the average stress in pillars and the maximum stresses in roof layers. Experimental procedures for making stress, strain, and in situ physical-property measurements in underground mines to check design calculations are outlined and the results discussed.

Jan 1, 1960

By THOMAS LEONBRD WATSON

I. INTRODUCTION. THE results embodied in this paper are based on a careful field- and laboratory-study of the lead- and zinc-deposits of the Virginia-Tennessee district, begun in the latter part of the summer of 1904 and completed in the spring of 1905, preparatory to the publishing of a State report .on them. A separate description of the individual deposits in Virginia is purposely omitted, since I have already described them in considerable detail in a State report. The Tennessee deposits are described here in some detail for the reason that no detailed record of them has yet been published. Practically, this paper summarizes the results obtained from a study of the geology of the ore-deposits of the district as, a whole. (I had the pleasure of visiting the deposits of Virginia and Tennessee with Dr. H. Foster Bain of the U. S. Geological Survey, in April, 1905. Figs. 21 and 22 are from photographs taken by Dr., Bail.) II. HISTORICAL. . The first authentic records of lead-mining .in Virginia date hack more than 150 years; and the old lead-mines at Austinville, on New river in Wythe county, V a., were the first to be worked. Colonel Chiswell, a native of Wales, and one of the earlier adventurers in southwestern Virginia, was one of the first operators of the Austinville mines. Chiswell's operations at Austinville commenced in the year 1750, and closed shortly after the beginning of the Revolutionary War, in the' year 1776, covering a period of about 25 years. From that time to the present, mining has been carried on almost continuously in the Virginia area. For many years after the Virginia mines were operated, mining was confined exclusively to the lead-ores. The zinc-ores

Mar 1, 1906

By Horace C. Porter, F. K. OVITZ

Much has been written of the changes undergone by coal in storage and the deterioration of coal through exposure to the weather. In order to obtain definite information for the benefit of the Government departments and of all who store coal in large quantitieS', a series . of tests was begun in the fall of 1909 under the supervision of tT. A. Holmes, then chief technologist of the United States Geological Survey, and was continued by the Bureau of Mines after its establishment in 1910. The tests were confined to determinations of the loss in heating value of the coals and did not include a study of other deterioration; for exaIp.ple, in coking quality or the yield of by-products in coking. The Bureau of Yards and Docks of the Navy Department cooperated in tests of New R~ver (W. Va.) coal, a variety largely used by the Navy. A preliminary report presenting a brief account of the early results of these tests has been published by the Bureau of Mines as Technical Paper 16.a The detailed report is presented in this bulletin, which gives a fu11 account of the tests and the analytical data covering a period of five years' storage. Data of somewhat similar experiments for shorter periods with gas coal from the Pittsburgh bed, with Pocahontas coal on the Isthmus of Panama, and with Sheridan, Wyo., subbituminous coal, which is used for railroad and other purposes in the West, are included. The tests of New River coal, in cooperation with the Navy Department, were undertaken to determine the advantage to be gained by storing coal under water, and particularly under salt water. Small lots were used in order to make the tests of maximum severity, and parallel experiments were made with run-of-mine and crushed coal under one-fourth inch size. All of the small lots tested under the different conditions (except those tested near Key West, Fla.) were taken as representative portions from one large original lot. The tests of Pocahontas coal, which, like the New River, is semibituminous, were undertaken chiefly to determine th.e effect of the tropical conditions in Panama. They were made on an outdoor pile of 100 tons of run-of-mine coal. Pittsburgh gas coal, a high-volatile, bituminous type used at gas and by-product coke works, was exposed for test at Ann Arbor, Mich., in cooperation with the University of Michigan. The university agreed to make tests at successive intervals of storage to determine, in its illuminating-gas experiment station, the yields of gas and byproducts from the coal. The coal, screened lump, was stored in about 4-ton lots out of doors in open bins. Subbituminous coal, which is mined in Colorado, Wyoming, and other States, and is known also as "black lignite," is commonly supposed to deteriorate rapidly in storage, especially by "slacking" or crumbling of the lumps. The tests herein described were undertaken at Sheridan, Wyo., in cooperation with the Chicago, Burlington & Quincy Railroad Co., in order to determine the extent of this slacking and the accompanying loss of heat value. The tests were in open bins holding 4 to 12 tons.

Jan 1, 1917

By M. Nakai, G. Itoh, R. Yamada, A. Kurumada

In order elucidate the mechanism for poorer fatigue properties of 7000 series aluminum alloys than those of 2000 series alloys, the effect of the test environment on the fatigue crack growth of the two series alloys was investigated, considering the relationship to hydrogen embrittlement. Two 7075-type and four 2024-type alloys were T6-tempered and T4-tempered respectively, and subjected to fatigue crack growth tests in moist and dry environments. When tested in moist air, fraction of intergranular crack path was higher in the 7075-type alloy with coarse equi-axed grains than in the 2024-type alloy with similar microstructure. This was in accord with the larger crack growth rate in the 7075-type alloy. Both the intergranular crack path fraction and the crack growth rate were decreased by changing the environment to the flow of nitrogen gas. Thus, the large fatigue crack growth rate of the 7075-type alloy is attributable to hydrogen embrittlement.

Jan 1, 2015

By K. Yarnaguchi

In the Mitsubishi Continuous Copper Converting Furnace, calcium femte slag is used. Due to its extremely high basicity, the improvement of corrosion resistance of the refractory lining is in need. In order to clarify the corrosion mechanism and to search for a new corrosion resistant material, first, the surface snuctures of bricks corroded in molten slags were observed by EPMA. Second, the dissolution behaviors of sintered MgO-based pellets containing various oxide additives were examined. It was found that the formation and the dissolution of magnesiofemte at the surface of the bricks play an important role in their corrosion and an addition of NiO, Mn02, or Ti02 to MgO is effective in stabilizing the magnesio-femte and improving the corrosion resistance of MgO.

Jan 1, 1994