Search Documents

By Oscar E. Harder, H. A. Grove

It is now just a quarter of a century since Fred W. Taylor§(23) pub-lished his classical paper On the Art of Cutting Metals, describing his researches in which he, in cooperation with Maunsel White, had developed what is essentially the modern method of heat-treatring high-speed steels. Regarding this research, Dr. Sauveur,(22) in his address on Steel Wizards, Past and Present, at the annual banquet of the American Society for Steel Treating in Philadelphia in 1920 said, "The discovery of high-speed steel, or if you prefer, of the treatment imparting high-speed properties to certain steels by Taylor and Maunsel White I am inclined to consider as our one epoch-making contribution to the metallurgy of steel." It was at about that same time (1900) that Taylor exhibited high-speed steels, heat-treated by the improved process, at the World's Exposition in Paris and attracted much attention by showing that the steels would operate at such feeds and speeds that the tips of the tools were visibly red hot. This observation must have started metallurgists to wondering regarding the relative hardness of the various steels at red-heat temperatures. Considerable work has indeed been done in an effort to measure the hardness of high-speed steels and related materials in the red-heat range, using various methods. The result's, however, have been only partly satisfactory, owing to experimental difficulties. The present investigation had as it's immediate inception an address by J. V. Emmons, of the Cleveland Twist Drill Co., to the Columbus Chapter of the American Society for Steel Treating in 1931, in which he deplored the fact that comparatively little was known with regard to the hardness of high-speed steels at elevated temperatures, in spite

Jan 1, 1933

By R. J. Wagner, Jim Douglas Jr., P. M. Blair

The calculation of the behavior of an oil reservoir during a water flood has long been an important problem to reservoir engineers. Buckley and Leverett derived the differential equation which describes the displacement of oil from a linear porous medium by an immiscible fluid, but this equation could not be solved by the methods of classic mathematics. Consequently, in order to integrate the equation over the length of the reservoir, they neglected the effects of capillary pressure. In the present paper, a numerical method has been developed for determining the behavior of a linear wafer flood with the inclusion of capillary pressure. The differential equation which was derived for the case of incompressible fluids is second order and non-linear. This differential equation was approximated by an implicit form of difference equation which is second order correct in both time and distance. An electronic digital computer was used to perform the numerical solution of the difference equation. INTRODUCTION The problem of calculating the flow and distribution of fluids in an oil reservoir subjected to a water flood has long challenged the reservoir engineer. The ability to solve this problem would provide a valuable tool for the design and study of field waterflooding programs. One of the first contributions in this field was made by Buckley and Leverett,'.' who developed a method of calculating waterflood performance in a linear reservoir. Their technique was limited by the practical necessity of excluding quantitative consideration of capillary pressure. It is the purpose of this paper to describe a method for calculating the behavior of a linear water flood with capillary pressure considered. This method, although limited to the linear case, should serve as a step toward the solution of the two- or three-dimensional waterflooding problem which would better describe actual reservoirs. The treatment of the problem has assumed that the reservoir is linear and homogeneous, that both oil and water -are incompressible, and that gravitational forces may be neglected, and that water is injected into one end of the reservoir and oil and water are produced from the other. Though these assumptions may not be directly applied to natural reservoirs, they are closely approached in many laboratory core tests. The physical problem has been represented mathematically by means of a differential equation and suitable boundary conditions. The inclusion of capillary pressure effects causes the differential equation to be second order and non-linear, and it is not amenable to solution in terms of known functions. Nevertheless, the problem may be solved by numerical methods. The authors have successfully calculated several cases from the start of water injection through to depletion of the hypothetical reservoir using realistic capillary pressure and relative permeability characteristics that were chosen so as to put the method to a test. DIFFERENTIAL EQUATION In two- or three-dimensional problems involving the two-phase flow of incompressible fluids through a porous medium, the equations describing the flow can be combined until only two dependent variables remain, the pressure in one phase, and the saturation of one phase. These variables appear in two simultaneous partial differential equations which are derived on the basis of the conservation of mass and Darcy's law as applied to two-phase flow. For a linear reservoir, this system of differential equations can be reduced to a single, nonlinear, second order, parabolic differential equation for one dependent variable, the saturation of one phase. For incompressible water and oil, it can be shown that the conservation of mass for the two phases requires that Where q, and q, are the water end oil flow rates per unit cross-section, s, and so their saturations, +, the porosity, and [ and T, dimensional space and time variables. Darcy's law, as extended to two-phase flow including the effect of capillary pressure,' is as follows:

By T. Hadley, Northern Minerals Ltd, C. S. Griffith, T. A. Safinski, K. H. Soldenhoff, M. Fainerman-Melnikova, A. Manis

"ANSTO Minerals and Northern Minerals have been working together since 2012 on the process flowsheet development for the Browns Range project for the recovery of the heavy rare earths (Dy – Lu, + Y). Initial efforts were directed toward defining the most efficient and direct flowsheet for the Preliminary Feasibility Study (PFS), issued in June 2014, then towards the Definitive Feasibility Study (DFS), issued in February 2015. These goals were achieved by undertaking comprehensive laboratory and continuous piloting programs. Further improvements to the flowsheet following the DFS have been made. This publication provides an overview of the evolution of the process flowsheet based on these laboratory and piloting programs from the PFS through the DFS and beyond.INTRODUCTIONNorthern Minerals Ltd (Northern) has been working on developing their flagship project at Browns Range for the recovery of the heavy rare earth elements (HRE, Dy – Lu, + Y). The project is located in the north of Western Australia as shown in Figure 1. The Total Mineral Resource at the project is currently estimated at 8.98 Mt @ 0.63% total rare earth oxides (TREO) comprising 56,663 t of contained TREO using a cut-off grade of 0.15% TREO. Of the Total Mineral Resource, 58% is classified as Indicated Resource, with the remainder in the Inferred Resource category.The deposit is characterised by breccia-hosted, hydrothermal, HRE-rich, xenotime mineralisation. The main gangue mineral associated with the xenotime is quartz. The distribution of rare earths (RE) observed for the xenotime mineralisation at Browns Range is presented in Figure 2. Extensive test work has shown that the xenotime can be readily beneficiated to between 20 – 40% rare earth oxide (REO) using a process consisting of crushing and grinding, followed by magnetic separation and flotation steps. Continuous piloting of this process was conducted on ~80 t of trench-sourced ore in late 2013 at SGS Perth, to produce ~2 t of ~20% REO mineral concentrate (MC) for hydrometallurgical testing. The composition of the MC produced during piloting is presented in Table 1."

Jan 1, 2016

By E. V. Kleber, V. F. Novy, R. C. Vickery

The constitutional diagram has been determined in part for the sgstem Gd-Fe. Seven intermetallic compounds have been found at compositions corresponding to the following Gd-Fe ratios; 2:3, 1.2, 1:3, 2:7, 1:4, 1:5, and 2:17. The GdFe, com-pound has a congruent melting point above 18000C, whereas all of the remaining compounds melt incongruently, A eutectic exists at 13 wt pct Fe at a temperature of 860°C. ALTHOUGH an increasing amount of information is becoming available on the metallurgy of pure rare earth metals, relatively few studies have been made on alloy systems of the rare earths with the transition metals; iron, nickel, and cobalt. Even less data are extant on gadolinium alloys although it could be expected that such alloys might possess interesting structural and magnetic properties. In this paper, we report investigation of the gadolinium-iron alloy system. Studies on systems containing nickel and cobalt will be presented in subsequent papers. Previous data on gadolinium-iron compounds have been reported by Endter and Klemm1 and Jep-son and Duwez.2 Both reports agree on the existence of the GdFe2 phase, which crystallizes with the C-15type structure (face-centered cubic). This is in accord with results of the present work. EXPERIMENTAL The gadolinium metal used was prepared by met-allothermic reduction of high purity gadolinium fluoride. A typical analysis of the metal thus produced indicated the principal impurities to be oxygen, 0.24 pct, and tantalum, 0.2 pct. The iron metal used for alloying was a reagent grade material. Alloys were prepared by arc melting mixtures of the respective metals. Appropriate quantities of the two component metals were carefully weighed, blended and compacted. The compacts were then melted in an arc furnace consisting of a water-cooled copper hearth plate and a water-cooled tungsten-tipped counter electrode contained in a brass vacuum chamber. The furnace was evacuated to an absolute pressure of less than 1 with the leak rate established as being less than 20 per min. The furnace was then back-filled to a pressure of 25 mm of Hg, with a 75 pct He-25 pct Ar mixture. Arc melting at 25 v and 300 amp was maintained for about 30 to 60 sec until the entire visible area of the sample became molten, by which time surface tension had drawn the molten metal pool into a large bead. After allowing the furnace to cool, the alloy button was inverted and the melting process repeated. A series of melts was made covering entire composition ranges from 100 pct Gd to 100 pct Fe. All samples were examined metallographically in the as-melted condition. As the phase diagram became rationalized, and differential thermal analysis had given indications of temperature arrests, annealing was carried out in vacuo or in argon. Generally, compositions containing more than about 60 pct Gd were heat treated at 750°C and alloys containing less than this quantity of gadolinium were annealed at 1000°C. Prolonged annealing times were of the order of 100 to 200 hr. Metallographic examination was repeated on the annealed materials. Although little material loss was noted during alloy preparation, chemical analyses were made on all specimens prepared. The following standard, analytical techniques were used. Samples were dissolved in hydrochloric acid; insoluble material was filtered off, ignited and fused with potassium pyro-sulfate. The cold melt was leached with dilute acid and the solution thus obtained added to the main sample solution. Gadolinium was always determined gravimetri-callv as oxide from oxalate ignition. Iron was removed from an aliquot sample by electrolysis on a mercury cathode at approximately six volts. Gadolinium in the iron-free electrolyte was then precipitated as oxalate which was subsequently ignited to oxide. Iron was determined volumetrically in an aliquot solution by reduction with stannous chloride fol-

Jan 1, 1962

By C. M. McCulloch, Maurice Deul

A geologic study of Mines 32 and 33 in Cambria County, Pa., was conducted as part of a methane control research program. Areas of high methane emission and roof instability are encountered which are related to the structural and stratigraphic features that characterize the geologic setting of these mines. Locally the folds trend N 20° E ±2°, the direction of the butt cleat in the Lower Kittanning coal. The face cleat strikes at N 69° W ±2° and the systematic rock joint in the surface bedrock strikes N 67° W ±2°This suggests that a directional stress oriented N 70° W produced the folds and influenced the directions of coal cleat and systematic joint sets. Analysis of SLAR indicates three directions of prominent regional lineation: N 39° E, N 31° W, and N 70° W. Little gas was encountered during development mining; large volumes of gas are encountered when roof falls. Most of the gas comes from strata above the mined coal; therefore, to control methane, roof instability must be controlled. Roof falls and high rates of methane emission are most likely where less than 30 feet of many thin layers of limestone, shale, and sandstone occurs between the Lower Kittanning coal and the next coal and in zones along the margins of a sandstone channel.

Jan 1, 1973

By John J. Sammarco

Computer-related accidents have caused injuries and fatalities in numerous applications. Normal Accident Theory (NAT) explains that these accidents are inevitable because of system complexity. Complex systems, such as computer-based systems, are highly interconnected, highly interactive, and tightly coupled. We do not have a scientific methodology to identify and quantify these complexities; specifically, NAT has not been operationalized for computer-based systems. Our research addressed this by operationalizing NAT for the system requirements of safety-related computer systems. It was theorized that there are two types of system complexity: external and internal. External complexity was characterized by three variables: system predictability, observability, and usability -the dependent variables; internal complexity was characterized by modeling system requirements with Software Cost Reduction dependency graphs, then quantifying model attributes using 15 graphtheoretical metrics the independent variables. Dependent variable data were obtained by having 32 subjects run simulations of our research test vehicle: the light control system (LCS). The LCS simulation tests used a cross-over design. Subject perceptions of these simulations were obtained by using a questionnaire. Canonical correlation analysis and structure correlations were used to test hypotheses 1 to 3 - the dependent variables predictability, observability, and usability do not correlate with the NAT complexity metrics. Five of 15 metrics proposed for NAT complexity correlated with the dependent data. These 5 metrics had structure correlations exceeding 0.25, standard errors < 0.10, and a 95% confidence interval. Therefore, the null hypotheses were rejected. A Wilcoxon signed ranks test was used to test hypotheses 4 to 6 - increasing NAT complexity increases system predictability, observability, and usability. The results showed that the dependent variables decreased as complexity increased. Therefore, null hypotheses 4 to 6 were rejected. Lastly, this work is a step forward to operationalize NAT for safety-related computer systems; however, limitations exist. Opportunities addressing these limitations and advancing NAT were identified. Lastly, the major contribution of this work is fundamental to scientific research - to gain knowledge through the discovery of relationship between the variables of interest. Specifically, NAT has been advanced by defining and quantifying complexity measures, and showing their inverse relationship to system predictability, observability, and usability.

By Dennis B

The Hilton Mine, 20 km north of Mount Isa was discovered in 1947. The underground mine has been a significant producer from 1989. The long development history is the result of complex orebody geometry, difficult metallurgy, dewatering problems and competition for development funds from the then expanding Isa Mine at Mount Isa. At present it produces 1.4 million tonnes annually. Its 21 million tonnes of reserves are necessary to supplement Isa Mine production.Hilton Mine is located in the Urquhart Shale formation of the Mount Isa Group, within the Mid Proterozoic Mount Isa Inlier. The seven developed orebodies have suffered strong structural deformation. Each orebody has a unique mixture of mineralogy and texture which effects ore value and metallurgical performance. These characteristics have proven useful for correlation purposes.The faulting and folding have caused difficulties with orebody interpretation, geomechanical complexities and has influenced the choice of mining methods: Initial cut and fill and open scope designs have given way to bench mining methods in response to better understanding of the eedloav and economic constraints.

Jan 1, 1993

By Raynor Linzey, Karl M. Busen

The formation of thin films of silicon oxide by anodic oxidation of silicon and the subsequent removal of these films by an etch is a process often used for the evaluation of concentration distributions Profiles) in silicon layers by the differential sheet conductance method. The accuracy of the resulting profile is very strongly influenced by the uniformity of the thickness of the reacted silicon. Normally, it would be expected that for a constant number of coulombs passed the thickness would be the same from oxidation to oxidation. Investigations show that in certain electrolytes, for a given number of coulombs passed through an n-type silicon sample, the thickness of the reacted silicon increased with increasing resistivity. Even for the same resistivity the thickness varied sometimes by a factor of 1.5. When an electrolyte was used which consisted of 10 pct water by volume in ethylene glycol with 4.0 g KNO per 1000 ml of solution, anodiza-tion at 5 ma per sq cm led to satisfying results. Short-time anodizations gave oxide layers of a higher apparent density than those experienced from thermally gown silicon oxides. THE functioning and the electrical characteristics of semiconductor devices are based upon the incorporation of "impurities" into a single-crystalline body of suitable material and on the concentration distribution (profile) of this impurity. The incorporation can be achieved by well-known processes as, for example, by diffusion, epitaxial growth, alloying, or ion implantation. Often the profile resulting from these processes is not known. A powerful tool to learn about a concentration distribution is given by the method of differential sheet conductance which employs successive four-probe measurements on a layer subjected to stepwise removal of thin sublayers. Differential sheet conductance vs position (or penetration depth) of a sublayer is plotted and a smooth curve is drawn through the data. From this curve the profile is then calculated. When the semiconductor material is silicon, the sublayers are removed suitably by anodic oxidation of the silicon and subsequent dissolving of the formed silicon oxide by an etch. The accuracy of the resulting profile is very strongly influenced by the uniformity of the sublayer thickness. Normally, it would be expected that, for a constant number of coulombs passed, the thickness would be constant from oxidation to oxidation. Investigations showed that for sublayers several hundred angstroms thick the reproducibility can be rather poor. Therefore, efforts were made to obtain a reliable technique for uniform removal. The present paper describes such a technique and certain phenomena which were encountered during the investigations. APPARATUS AND TECHNIQUE The first report on the investigation of concentration distributions, where for differential sheet conductance measurements thin silicon sublayers were removed from a diffused layer by anodic oxidation, was given by Tannenbaum. The author reports the removal of sublayers which for the most part were 400 thick. More advanced device designs now require much narrower layers. When it was tried in these laboratories to determine profiles within such layers, difficulties were encountered with respect to sublayers which by necessity had to be thinner than the ones reported by Tannenbaum. The apparatus used for the investigations is sketched in Fig. 1. Two cylindrical containers connected by a wide tube are filled with an electrolyte. The left container receives the cathode whereas the right container is closed at the bottom end by a sample support consisting of a Teflon base and a copper pedestal. The silicon sample (1 by 1 cm) is mounted to the pedestal embedded flush in the Teflon base using silver paint (Degussa) for electrical contact. Pyseal is applied to the edges of the sample to protect the copper pedestal from the electrolyte. The base is mounted to the container using a water-tight silicon rubber gasket. Fig. 2 gives a view of the sample support. The copper pedestal is connected to the positive side of a power supply operating at a constant current output (Kepco Model ABC 425M). The electrolyte which has been reported by Duffek et al. consisted of either 2 or 10 pct water by volume in ethylene glycol and 4.0 g KNO3 in 1000-ml solution. The electrolyte is best prepared

Jan 1, 1967

By Carle R. Hayward

This work was first undertaken in the metallurgical laboratory of the Massachusetts Institute of Technology in 1907 by L. A. Dickinson, E. Phelps, and V. S. Rood, under the author&apos;s direction. They attempted to determine the diagram for the system Cu2S-MiS, but several inexplicable results were obtained. The following year, P. H. Mayer with Mr. Dickinson carried on some experiments with nickel sulphide and found that the molten material slowly lost sulphur until it reached a composition corresponding to the compound Ni3S2, established by Bornemann.l At this point the composition remained stable. The freezing points of the mixtures gradually fell off with the loss of sulphur. Since the above facts seemed to explain the erratic results obtained in the first experiments, Mr. Mayer with F. Jaeger attempted in 1910 to establish a correct equilibrium diagram for the Cu2S-Ni3S2 series. They prepared pure Cu2S and Ni3S2 and determined the cooling curves for various mixtures. The fusions were made in a platinum resistance furnace and the temperatures were measured with a platinum-iridium thermocouple connected with a Sullivan galvanometer. The curve was established for mixtures containing more than 40 per cent. Cu2S, but they were unable to determine certainly the direction of the curve beyond that point. Nothing further was attempted with this series until the present year, when the work was carried to a successful conclusion with the assistance of A. Butts, Jr., and E. H. Weil. The results of this work are given in the following pages. Preparation of Cu2S.—A piece of cathode&apos; copper from the Buffalo plant of the Calumet & Hecla Co. was cut into shavings by a shaper and converted into sulphide by heating in boiling sulphur. A porcelain casserole was used for the purpose, the heat being furnished by a Bunsen burner. It was found that after boiling in the sulphur for an hour the copper shavings were completely converted into sulphide. The liquid sulphur was then poured off, leaving the solid sulphide in the casserole in

Jan 1, 1915

By Lance Helwirg

New high and low double outfall bridge structures for a juvenile fish bypass system have been constructed on the Washington Shore approximately two miles downstream from the Bonneville Dam on the Columbia River. The high and low outfalls each extend approximately 400 feet into the river from the Washington shore and are designed to release juvenile salmon into the river at above-water discharge elevations for improved survival rates. The two outfall structures include post-tensioned concrete double box flume girders approximately 7 feet high by 13 feet wide, which will be submerged in river flows as high as 15 feet per second. Each of the 6 offshore foundation piers is composed of a single 10-foot diameter reinforced concrete drilled shaft with a permanent steel casing embedded into the river bottom approximately 100 feet. Challenging outfall design conditions included designing the entire structures to be submerged for long periods of time in 15-feet-per-second river water flow with a 60-foot cantilever at the end of each outfall, and with the superstructure 70 to 80 feet above the river bottom. Figures 1-1,1-2, and 1-3 show the high and low outfall structure overhead photos and elevation view.

Jan 1, 2001

By F. Keller, J. D. Edwards

The anodic treatment of aluminum presents problems of scientific as well as of commercial interest.l-3 Of particular interest is the fact that, during the anodic oxidation process, the oxide continues to form at the metal-oxide interface under any oxide previously formed. This has led to speculation as to the mechanism involved in the formation of the relatively thick oxide coatings that are used commercially for decorative or protective purposes. Furthermore, the ability of certain types of oxide coatings to adsorb dyes and other substances has stimulated research to determine the actual structure of these adsorptive coatings. It has been found that anodic oxide coatings on aluminum are composed essentially of aluminum oxide. They are formed by the action of oxygen ions penetrating to the metal surface during the electrolytic oxidation treatment. These coatings can be formed in a number of different electrolytes, as for example, those which contain sulphuric acid, chromic acid, oxalic acid, or boric acid. These are the commonest and most useful electrolytes employed commercially. Except for certain specific conditions of formation, the coatings in general have been found to be amorphous alumina, as far as can be determined by X-ray or electron-diffraction methods. Anodic oxidation processes can be arranged in three rather general classes if they are grouped in relation to the solvent action of the electrolyte on the coating.4 In the first class, the electrolyte has little or no solvent action on the coating that is formed. In general, coatings produced under such circumstances are nonporous and non-adsorptive. In the second class, the electrolyte exerts an appreciable solvent action on the coating. These coatings are porous and adsorptive. Finally, for the third class, the electrolyte tends to dissolve the coating about as rapidly as it is formed. This action produces electrolytic brightening or anodic polishing of the aluminum surface and at most leaves only a very thin film of oxide. The nonporous and nonadsorptive type of oxide film is represented by the coatings that are formed when solutions of boric acid are employed as the electrolyte. It is especially significant that these impervious films are formed in electrolytes that exert little or no solvent action on the coating. Where a boric acid electrolyte is used, the coating tends to form rapidly, with the result that the flow of current is soon reduced to substantially zero. This indicates that the growth of the coating has stopped. As a rule, the thickness of the coating is roughly proportional to the voltage employed for formation and the coatings of this type are exceedingly thin. In an electrolyte of this type, the coating has a high resistance when the aluminum is made anode; consequently, any current that may flow (leakage current) is very

Jan 1, 1944

By John T. Norton, Robert J. Anderson

The purpose of this paper is to report evidence, regarding metal structures, that is contradictory to the amorphous-metal hypothesis of Beilby, and particularly evidence that is opposed to the proposition that a vitreous amorphous layer is produced by polishing a piece of metal. According to the theory of Beilby, which has been developed by Rosenhain and others, polishing a piece of metal greatly affects the condition of the metal at or near the surface polished, making that surface entirely different in character from the metal beneath. A vitreous amorphous surface film is said to be formed. The polishing process, on the basis of Beilby&apos;s explanation, is well known and does not require discussion here, but it is advisable to seek the precise meaning of the term "amorphous." According to Beilby, "amorphous means non-crystalline in the most intimate sense of the word; the molecules arc not marshalled in crystalline order and orientation." According to Rosenhain, the amorphous condition is that assumed by a metal when the crystalline arrangement is completely broken up so that the atoms exist in a state of disorderly arrangement similar to that which exists in the liquid state. Thus, from the point of view of the phase rule, the "amorphous phase" is regarded as being identical with the liquid phase. Amorphous metal is often likened to an undercooled liquid. A crystalline substance is one in which the atoms are arranged in space according to some definite repeating geometrical pattern. The existence of amorphous metal has not been definitely proved. The evidence offered here that amorphous metal probably does not exist is of a direct nature and is afforded by x-ray diffraction effects given by a number of metals and alloys when polished, cold-worked, and annealed. Considerable of the experimental work was carried out with substantially pure aluminum and the aluminum alloy duralumin, but many of the observations made on these materials were checked by similar observations on copper, iron, tin, zinc, lead, mild steels, and

Jan 1, 1925

By M. M. Tilman

The Bureau of Mines conducted research to determine whether it is possible to substantially improve the fatigue resistance of lead sheet by means of surface coatings. Five types of coatings were applied to unalloyed chemical lead sheet. Flexural tests revealed that the best fatigue resistance was obtained with coatings of vacuum grease. Vacuum-grease coatings on unalloyed lead sheet resulted in fatigue resistance at least as good as that of the fatigue-resistant alloy Pb-0.04 Ca. Coated lead sheet was also tested in short-time tensile tests and in tensile creep tests. Tensile and yield strengths were increased by several of the coatings with only moderate loss of ductility. Creep resistance was also improved in varying degrees by most of the coatings. The Bureau also conducted research on the effectiveness of noise barriers by using sheet lead in combination with other materials. Noise barriers consisting of continuous-cast sheet lead with gypsum board were found to be effective and relatively inexpensive barriers.

Jan 1, 1978

By F. Forscher

Pronounced porosity, decreasing with distance from the fracture surface, is found in the necked region of tensile specimens tested at room temperature or liquid nitrogen temperature. A hydrogen solution treatment followed by a quench prevents pore formation in tests at —196°C, but has little effect on tests made at room temperature. Reduction of area values at —196°C are strikingly improved by the same treatment, but show no improvement in room temperature tests. The experimental results support the hypothesis that strain-induced porosity results with hydride initially present or, in material containing less than 50 ppm H, with hydride precipitated by strain aging. ZIRCONIUM&apos;S advent as an engineering material in nuclear reactor construction has brought forth many investigations concerned with the properties of this metal and its alloys. Some attention has been given to the ductility of the metal.1, 2 Particularly, the effect of hydrogen on the impact strength was noted," indicating a pronounced dependence of ductility on the hydrogen content and its distribution in the metal. Micro graphic:&apos; and X-ray diffraction studies&apos; have shown that a precipitated hydride phase causes embrittlement in zirconium,&apos; which implies a distinctly different mechanism from that causing hydrogen embrittlement in steels."-&apos; In the latter case, it is assumed that atomic hydrogen diffuses to rifts, where it forms molecular hydrogen under such internal pressures that it causes the rifts to enlarge, leading to fracture. Thermo-dynamic studies of the Zr-H system8, 9 also indicate that the internal pressure of molecular hydrogen would be too low to cause any damage to the zirconium at room temperature, and the formation of a zirconium hydride (d phase) is favored." It is noteworthy that this phase has a face-centered-cubic structure and nearly 18 pet larger molar volume than close-packed-hexagonal a-zlrconlum&apos; Other features of the ductility of zirconium are the absence of a typical cup-cone failure upon tensile testing, a pronounced strain-induced porosity in the necked region of a tensile bar, Fig 1, and the associated spongy appearance of the fracture surface A tremendous improvement in ductility at liquid nitrogen temperature can be observed following a heat treatment that retains the commonly present quan- tities (10 to 50 ppm) of hydrogen in solution. Such tests show a typical cup-cone failure and the absence of strain-induced porosity, Fig. 2. The present paper reports results of an investigation into the causes of strain-induced porosity in zirconium. Room temperature tensile fractures of mild steel, aluminum, and titanium have also been examined for strain-induced porosity. In each case porosity could be detected, but the amount was orders of magnitude less than was found in zirconium. Of the three metals, titanium showed the strongest effect. Material, Specimens, and Preparation The greater part of this investigation was done on Westinghouse crystal bar zirconium, are-melted, forged, and hot-rolled. Chemical analyses of the hot-rolled plates are given in Table I, along with those of the Foote crystal bar zirconium used in this work. The specimens were machined from the hot-rolled plate (1550°F) of 1/2 in. thickness and subsequently heat-treated according to one of the treatments shown in Table IS. All specimens were machined round, the longitudinal axis in the rolling direction, with a gage

Jan 1, 1957

By G. L. Oldright, T. B. Brighton, C. M. Dice

The base bullion from the lead blast furnace contains varying amounts of the impurities left in the smelter feed by the concentrator, regardless of the method of smelter operation. These impurities may be held in part in mechanical suspension rather than being present as true alloys. However, usually there is little free space in the crucible in which to separate these drosses before the bullion is taken from the lead well. When such a dross is melted in a laboratory crucible and allowed to cool, the products obtained are lead bullion, speiss, and matte in well separated layers. Typical analyses of layers are: Analyses. Per Cent Element Bullion Speiss Matte Pb.............................................. 92.0 41.2 38.3 Cu.............................................. 2.4 36.3 40.6 As............................................... 4.0 16.5 4.3 Sb............................................... 0.7 0.2 0.4 S................................................ 0.6 1.9 13.1 Fe............................................... 0.0 0.0 0.0 Totals......................................... 99.7 96.1 96.7 The absence of iron in these products drossed from the blast-furnace bullion proves that the impurities for the greater part are not simply finely divided blast-furnace speiss or matte that has been dissolved or dispersed in the lead, but are held in solution by the liquid metal and rise to its surface as infusible compounds when the temperature of the bath is lowered. In general, the drosses made locally are metal sulphides and arsenides and not oxidized compounds. The large content of metallic lead also does not seem to be retained because of oxidized compounds

Jan 1, 1937

By Glatthar J. W, Lauder D. W, Manlapig E. V, Mackinnon I. R

The Ok Tedi copper orebody consists of porphyry and skarn orebodies. The skarn orebodies, identified by different mineralogies, are the source of high intermittent fluorine levels in the mill concentrates. This paper discusses the results of t

Jan 1, 1998

By Katherine Mather

This paper is an attempt to put together petrographic, physical, and chemical data about the large and varied group of rocks generally called limestones. Results of the properties of these rocks on their performance as concrete aggregates are discussed. CRUSHED stone classified as limestone comprises about 70 pct of the crushed concrete aggregate and roadstone produced in this country, and the product has amounted in the recent past to about 97 million tons per year, valued at more than $123,-000,000.&apos; Therefore an evaluation of the properties of rocks classified in these statistics as limestones and an ability to predict their behavior as aggregate in portland cement concrete are matters of considerable economic consequence to producers and consumers of aggregate. This paper is an attempt to put together petrographic, physical, and chemical data about the large and varied group of rocks generally called limestones. It also points out certain results of the properties of these rocks on their performance as concrete aggregates. The problems encountered in efforts to explain the behavior of limestones, dolomites, and related rocks as concrete aggregate lie on the frontiers between the ignorance of the geologists and the ignorance of the engineers. The mineral composition and textures of the rocks have not been adequately explored and described, and the effects of mineral composition and texture on the performance of aggregates have been worked out in only a few cases. There are instances of unsatisfactory performance and some generalizations of those experiences. There are many more examples of satisfactory performance than of unsatisfactory, but there is practically no published information as to why a particular aggregate was satisfactory in a specific use. There are all too few investigations of undeteriorated concrete; more is known about the pathology of concrete than about its normal structure and aspect. As part of the investigation of aggregates, the classification of rocks is not an end in itself, but is a step toward recognition of properties expected to influence the behavior of aggregates in their intended use. Rock of any type may perform well or poorly as concrete aggregate, depending on the physical condition of the rock, its physical and chemical properties as compared to those of the matrix in which it is placed, and the circumstances under which the concrete is exposed. Some classification and descrip- tion of the limestones is necessary to distinguish subgroups whose members will probably behave in similar ways and to evaluate the group as a whole. The group name, limestone, includes and tends to conceal the identity of rocks that have a very great range in chemical and mineralogical composition, structure and texture, conditions of deposition, subsequent history, and suitability for use as concrete aggregate. All the rocks classified as limestones include one or both of the most abundant rock-form-ing carbonate minerals, calcite and dolomite, as major constituents. Carbonate rocks is a more descriptive and more accurate group name than limestone, which has generally been used to include dol-omitic or magnesian limestones and dolomites as well as calcitic limestones. Classification and Description of the Carbonate Rocks The question of names to be applied to the carbonate rocks may appear academic, but it is of practical importance as long as there are specifications for aggregate that result in acceptance or rejection of rocks by name and as long as failure to make distinctions among the carbonate rocks leads to misunderstandings of their properties and of what may be expected of them in performance. Materials included in production statistics as limestone and tested for concrete aggregate as limestone range in fact from calcareous shale and calcareous or dolomitic sandstone and argillaceous limestone and dolomite to calcitic limestone and pure dolomite and to rocks close to calcitic and dolomitic marble. To take a simple example: consider two manufactured coarse aggregates, both dense and unweathered, one composed principally of crystalline calcite and the other of crystalline dolomite, but both known as limestone. If each is used as coarse aggregate in a standardized concrete mixture with the same fine aggregate used in both cases, made into concrete specimens, and tested in accelerated freezing-and-thaw-ing, the test results will probably be quite different, because of the differences in internal bond and thermal properties between the two aggregates. As long as both aggregates are called limestone, the test results cannot be explained, or used except in a very limited way; if the aggregates are distinguished as limestone and dolomite and the consequent differences in texture and thermal properties are recognized, the results are reasonable. Classification of the carbonate rocks used as aggregate should be based on structure and on composi-

Jan 1, 1954

By Ralph W. M. Lai, D. W. Fuerstenau

This paper presents the results of a study of the principles which control the distribution of ultrafine particles between an oil phase and an aqueous phase. Alkyl sulfonates were used to control the wettability of fine alumina particles and to stabilize the water-isooctane emulsion system in the extraction process. The effects of sulfonate chain length, sulfonate adsorption, pH, and oil-water ratio on the recovery of solids in the oil phase were investigated. Higher extraction was found under conditions which yield higher hydrophobicity and large interfacial area of the oil-water emulsion. Today there is considerable interest in developing methods for the recovery of fine particles from disseminated ores. One such method might be the extraction of fine particulate solids from aqueous suspensions into an oil phase, and one example of a successful industrial process based on oil-water distribution phenomena is the emulsion flotation process used in concentrating manganese ore.&apos; The oil agglomeration process of Farnand, Smith, and Puddington has been suggested for concentrating tin ore. Patents 3-4 for oil flotation processes extend back to that of William Haynes in 1860. The basis of all these processes is directly related to the stabilization of emulsions with solid particles. The first extensive study of oil-water emulsions stabilized by finely divided solids was made by Pickering. Later, Briggs,6 weston, 7 Chessman and King,8 and Leja and Schulman9 experimentally demonstrated how solid particles control water-oil and oil-water systems. Hildebrand10 suggested that fine particles can stabilize an emulsion because the fine particles are partially wettable by both oil and water, that is, that the contact angle must be finite. Takakuwa and Takamori 11 recently applied emulsion inversion to the study of collector adsorption in flotation systems. At the Royal School of Mines, Shergold and Mellgren12 are currently carrying out a comprehensive study of the extraction of fine particles into an organic liquid phase. In the present study of the liquid extraction or oil flotation of ultrafine particles, the recovery of hydro-philic alumina particles of 0.1-µ average diameter was determined after separating an isooctane-water mixture (emulsion) into its two phases. Alkyl sulfonates of different chain lengths were used to change the wettability of the alumina and to effect emulsifi-cation of the oil-water mixture. The effects of the oil-water volume ratio, sulfonate adsorption, and pH on the recovery of the fine particles were investigated. Since the surface charge on an oxide such as alumina is determined by the adsorption or interaction of H+ and OH- with the surface, pH control is extremely important. Furthermore, since the zero point of charge (zpc) of alumina13-14 occurs at pH 9 to 9.4, major adsorption effects with anionic collectors in these systems will occur below pH 9. The results of the foregoing investigation are discussed in terms of the recovery of the fine particles, the oil-water ratio, contact angles, surface tension, the adsorption of sulfonate onto the solid surface, and the emulsifica-tion of oil. MATERIALS AND EXPERIMENTAL METHODS Materials: The particulate solid used in all the experiments was Linde "A" alumina, a high-purity, readily available form of a-alumina. The surface area of the alumina, as evaluated from measurements of stearic acid adsorption from benzene, was 14.5 sq m per gm, based on a value of 20.5 sq Å for the cross-sectional area of stearic acid.13 All aqueous solutions were prepared from triply distilled conductivity water. Other materials included high-purity crystals of sodium alkyl sulfonates, isooctane, and, for pH adjustments, reagent grade hydrochloric acid and sodium hydroxide-Because sulfonic acids are strong acids, they are

Jan 1, 1969

By V. A. Phillips, M. Safdar Ali

The tensile properties of Cu-0.20 pct Al, Cu-0.45 pct Mg, Cu-0.27 pct Cr, and Cu-0.22 pct Be solid-solution alloys were studied at -196°, 18°, 2509 and 500°C on wires internally oxidized at 900°and 1000°C. Internal oxidation produced marked increases in yield strength relative to pure copper, particularly at low temperature. The yield strength decreased with increase in temperature to a much greater extent than predicted by current theories of dispersion hardening. The strengthening effect of internal oxidation persisted throughout the entire stress-strain curve, but since a marked loss of ductility occurred at all test temperatures, only modest increases in tensile strength were realized. INTERNAL oxidation involves the preferential oxidation of a baser solute in a relatively noble solvent by diffusion of oxygen into the solid. Since the process is diffusion controlled, it is expedient to carry it out at a high temperature often approaching the melting point. The amount of solute is limited and the oxidation conditions adjusted so that oxygen diffuses inwards to meet the solute causing reaction to progress inwards and form subscale instead of only sur face scale. The reaction can be made to occur throughout the thickness of thin material producing a fine dispersion of oxide inside the metal. C. S. Smith1"3 appears to have been the first to recognize the true nature of the process of internal oxidation. Although extensive kinetic and metal-lographic studies followed by Rhines and coworkers,4-5 Chaston7 andMeijering and Druyvesteyn8 working independently were the first to report hardening effects due to internal oxidation. These results prompted detailed studies of the effects of internal oxidation on the hardness, tensile, creep, and fatigue properties of a number of alloys by G. C. Smith and coworkers9-12 in England, on hardness by Gottardi13 in Italy, and on hardness and tensile properties by wood14 in the U.S.A. Publications dealing with other aspects of internal oxidation will not be reviewed here. Internal oxidation of solutes having a high affinity for oxygen provides a means of obtaining very fine dispersions stable in a suitable atmosphere at temperatures well above those at which most age harden ing precipitates coalesce. The process therefore offers a method of producing thin sheet and wire of possibly outstanding creep resistance. The size limitation might be overcome by internally oxidizing porous powder compacts made from alloy powder before final sintering. PREPARATION OF ALLOYS The alloy ingots, which were approximately 5 1/2 in. long by 1 in. diam, were made up in a high-frequency furnace, using as raw materials OFHC copper, 99.99 + pct Al, high-purity magnesium, and master alloys of Cu-4.19 pct Be and Cu-10 pct Cr. The alloys containing aluminum and magnesium were melted ii closed high-purity graphite crucibles and solidified in the crucible which was lowered partly Out of the coil to give a hot-top effect. The alloys containing beryllium and chromium were made by melting in vacuo in alumina-lined sillimanite crucibles. The magnesium, chromium, and beryllium

Jan 1, 1960

By G. E. Keller, G. D. Coe

Several methods have been devised for rapid determination of sulfur in coal using a high-temperature combustion furnace. The fundamental principles of the various methods are similar but the techniques vary widely. The method described herein is no different in principle from some of its predecessors but varies considerably in technique. Originally devised to overcome the low-accuracy criticism leveled against the others, the tube-furnace method has proved successful for limited applications. Work is being done to widen the applicability of the technique. Subsequent to the work of A. Vita1 in 1920, a number of investigators have published data dealing with the rapid determination of sulfur in coal using a high-temperature combustion furnace.2-5 These, together with several unpublished methods, involve wide differences in technique although they are all similar in principle. Investigation of typical details of procedure showed that poor precision or accuracy could be attributed to one or more of the following: 1) inadequate quantity of sample to be representative, 2) a delivery tube temperature too low to confine condensation to a washable area of the tube, 3) no provision for back washing the delivery tube, 4) incomplete absorption of the sulfur compounds due to inadequate bubbler, and 5) the false assumption that all of the sulfur is evolved as sulfur dixoide. The method herein discussed is no different in principle from some of its predecessors; the differences are in technique. Although the method is rapid—a determination can be completed in 5 min— accuracy has riot been sacrificed in order to achieve speed. MATERIALS AND EXPERIMENTAL WORK Fig. 1 shows the arrangement of the equipment. A metered volume of oxygen is passed through calcium chloride for removal of moisture, then through Ascarite for removal of carbon dioxide, and thence through a glass tee to the feed end of the combustion tube. Connected to the side arm of the glass tee is a rubber tube that is closed with a pinch clamp during combustion of a sample. The products of combustion are expelled through a Vycor bubbler, the end of which is submerged 3 cm below the surface of a 1 pct hydrogen peroxide solution contained in a 300 ml high-form beaker. At the completion of the 4-min combustion period the contents of the beaker are titrated to a yellow end point, using a methyl red indicator, with 0.05 N sodium hydroxide (or sodium tetraborate). The pinch clamp on the tube leading from the tee in the oxygen line is then opened and mouth suction applied to draw the hydrogen peroxide up into the bubbler past the ell, almost to the rubber tube connecting the bubbler to the combustion tube. This washing of the bubbler is repeated until no further acid reaction with the indicator is obtained. The hydrogen peroxide-sul-furic acid solution is then titrated to the final yellow end point. Test work conducted at the Robena Laboratory disclosed the following critical conditions that had important bearing on the precision of the method: Weight of Sample: Several series of tests wherein the sample weight ranged from 0.1 to 0.5 g of -60 mesh coal showed that the lowest variance (standard deviation squared) resulted from the use of 0.5-g samples; the variance was slightly greater when 0.3-g samples were used, and with less than a 0.3-g sample weight the variance increased rapidly with decrease in weight. Although the use of a 0.5-g sample invariably resulted in a very slight explosion as soon as the sample entered the hot zone of the combustion tube, this did not detract from the precision of the method. Temperatures: Mott and Wilkinson5 found that a combination of low temperature (1250°C) and low oxygen flow rate (less than 700 ml per min) tended to give high results due to formation of oxides of nitrogen. Although the method herein employs a much higher oxygen rate than 700 ml per min, as an additional precaution to assure accurate results, 1315°C (2400° F) is recommended as the most desirable furnace temperature. The temperature of the elbow of the bubbler should be at least 75°C to minimize condensation

Jan 1, 1961