Search Documents

By Jan Visman, James W. Parkinson

GENERAL INTRODUCTION Sample collection, preparation and analysis are all steps in a single process designed to provide information about a much larger amount of material than the sample itself. For example, information about the ash content of a unit train load of coal may be derived from a single, relatively small sample of perhaps a few hundred pounds (liters) extracted from the entire shipment. These three steps can be thought of as links in a chain, allowing the simple analogy that the strength of the chain, or, in other words, the value of the information is only as strong as the weakest link. Sample collection, discussed in Part 1 of this chapter, is critical because analytical procedures can do no more than reveal the characteristics of the sample presented to the laboratory. If that sample does not properly represent the population to be characterized, neither will the analysis of that sample. Sample preparation is also a critical part of the chain. Any change in the nature of a sample between the time it is collected and the time it is analyzed will appear to reflect the nature of the population. For example, sample preparation procedures that allow air to partially dry the coal sample before reaching the laboratory will cause the sample analysis to indicate a lower moisture content than the sample originally had. Other changes can be more subtle. Second only to moisture loss, oxidation reactions generally cause the greatest problems. Oxidation of a coal sample can alter surface properties, changing flotation response. In extreme cases, combustion parameters, such as caking or agglomerating properties or mineral composition, such as pyrite content, can change. Water samples can also be altered by oxidation. For example, ferrous iron can oxidize to ferric iron, possibly changing water quality parameters such as pH. Sample analysis, the subject of Part 2 of this chapter, is the final link in the chain. Obviously, no laboratory procedure can correct for problems created by improper sample collection and preparation. At the same time, poor analytical techniques will create incorrect information about the total amount of coal from which the sample was extracted (the population) in the same manner as improper sample collection and preparation. The key to gaining correct information about the population is to view these three steps as parts of a single process. Following proper techniques through only one or two steps of the process will not produce accurate information.

Jan 1, 1991

A sample of fifty fractured low chromium-molybdenum alloy drill steel rods was investigated. Each rod was of the forged collar integral tungsten carbide type in common use in Australia.Examination of a new rod of the same type showed that a zone of spheroidized carbide about 0·25 in. wide was present about 12 in. from the shank end.Examination of the fractured rods revealed that 78 per cent. of failures occurred within 0·25 in. of the spheroidized zone at the shank end but in the main stem of the rod rather than actually in this softened zone where it might be expected to occur.This predominant type of failure at the shank end in the steel rods is caused by a highly anodic region corresponding to the first stages of spheroidization of carbides present in the steel. Accelerated corrosion in the narrow band havil\g this structure induces the formation of stress-concentrating corrosion pits, 78 per cent. of failures in this region being due to corrosion fatigue.The remaining 22 per cent. of failures, occurring in the as-rolled stem, were due to either corrosion fatiglie if failure were initiated at the water-hole surface of the drill rod, or to a decarburized outer surface if failure originated at this surface.Temperatures producing spheroidization were determined as 6007600C.Evidence suggests that approximately 75 per cent, of shank-end failures in all forged collar drill rods can be attributed to corrosion fatigue occurring preferentially in that section showing partial spheroidization of carbides· produced by the forging and hardeningoperations.Methods are suggested for reducing the frequency of fatigue failures in drill rods.INTRODUCTIONAn integral part of all tunnelling operations through rock is the drilling of suitably placed holes i:n.to which explosive is subsequently rammed and exploded.The drilling operation, whether for metalliferous mining or for general civil engineering constructional work; is...

Jan 1, 1955

By M. K. Foster

Ten horizontal retort zinc blocks of a modified Hegeler design are in operation at Nueva Rosita, Coahuila, Mexico, and produce approximately 170 t of spelter daily, or 62 000 t/year. A block consists of two furnaces of 448 retorts each, making 8960 retorts as the plant complement. Each furnace block is fired with natural gas and air maintaining the combustion mixture in the furnace always slightly reducing. No attempt to recover energy through waste heat boilers is made. The spelter moves to market by rail and truck either in palletized bundles weighing approximately 1060 kg, as loose slabs weighing 26.5 kg each, or as 1088 kg ingots. At present 46% of the metal is exported and 54% is consumed domestically in Mexico. The present day trend toward equalized or alloyed spelter, as well as special shaped castings results in sales of 35% of the entire plant's production. Sulfuric acid is also produced by the Contact Process using vanadium pentoxide as the catalyst. The plant is basically a Monsanto contact system, producing approximately 68 t of 100% sulfuric acid daily. Both 98.5% sulfuric acid and 20% oleum are available. All of the acid made is consumed in Mexico. Shipments are made in 26,900 dm3 tank cars.

Jan 1, 1970

By Robert Mehl

PART I. ORIENTATION RELATIONSHIPS IN OXIDE LAYERS Oriented overgrowths and intergrowths among both metallic and nonmetallic substances have been recognized and studied for well over a century. The work of Widmanstätten in 1808 on the geometrical struc-ture in meteorites, a structure known by his name, demonstrated that oriented intergrowths can occur in purely metallic systems. This fact led to much of the early microscopic study of alloys, contributing greatly to the advance of physical metallurgy. The problem has been attacked again in recent years in a comprehensive fashion, with the object of dis-covering what atomic movements may occur during phase changes in alloy systems. Much of this work has appeared in the A.I.M.E. TRANS-ACTIONS in a series of papers published by Mehl and coworkers beginning in 19311. Although many aspects of this general problem remain unsolved, it may be said that the orientation of a new phase forming by precipitation from solid solution or by transformation invariably bears, a unique relationship to the orientation of the phase from which it formed, and that similarity in atomic patterns on atomic planes in the two phases play an important part in determining the orientation relationship. Analogous orientation relationships exist in oriented intergrowths in nonmetallic systems-mineral or inorganic. In 1827 Haidinger2 dis-covered natural intergrowths of hematite and magnetite, and demon-strated that the rough form of the magnetite octahedrons was delineated by small crystals of hematite, of which the basal (00.1) planes lay parallel to the octahedral cleavage planes of the magnetite. The description of this orientation relationship was later completed by von Rath3, who showed that the edge (00-1):(10-1) in hematite lies normal to the [111]

Jan 1, 1937

This paper will discuss specifically the performances of vibrating screens having circular motion with inclined decks and linear motion with horizontal or near horizontal decks and both related mainly to coal, metalliferous, and other granulated solids applications where screening and efficient classification is required. Some misconceptions have been applied in the past with regard to making a screen type selection using either circular throw or linear throw and therefore this paper will endeavour to clarify these misconceptions.

Jan 1, 1984

By Kneisley RO

This paper presents a brief overview of current bump mechanics theories and pillar design methodologies, and relates these concepts to experiences at two mines located in a north- central Utah coalfield where different pillar designs were used to control mountain bumps. Experiences gained at the first mine demonstrated the successful implementation of a two-entry, 9.8 m (32 ft)-wide, yield-pillar design. A U.S. Bureau of Mines field study quantified the timing of chain pillar yielding and resulting load transfer from the gateroad. In-mine pillar response, although apparently sensitive to site-specific conditions, compared favorably to estimates derived using two yield- pillar design methods. A second study conducted at another mine located in the same district, but subjected to different geologic conditions, documents the unsuccessful attempts to employ progressively narrower three-entry pillar designs based on successes achieved at the first mine site. This second mine never achieved a true yield-pillar design. Use of pillar widths ranging between 9.1 m (30 ft) and 27.4 m (90 ft) always resulted in violent bumps in the tailgate pillars. The pillars were either too large to yield, or too small to support peak operational loads. Hypothetical gateroad systems were evaluated using both analytical and empirical approaches for configurations comprised of two rows of conventional pillars, and systems incorporating both yield and abutment pillars. Analysis concluded that yield pillars less than 6.1 m (20 ft) wide and abutment pillars ranging between 30.5 m (100 ft) and 39.6 m (130 ft) square would be required to achieve a stable gateroad design. However, results of a field study conducted on a two-entry, 36.6 m (120 ft)- wide abutment pillar concluded that abutment pressures from the first panel overrode the pillar, and that a still larger pillar may be required to preclude bumps in the tailgate during second panel mining. Without the benefit of a demonstrated in-mine success, it is not clear which design would ensure elimination of gateroad bumps.

Jan 1, 1992

By L. L. Handy

Two equations are compared for calculating imbibi-tion rates of water into porous media. A linear relation was found to apply when the square of the volume of water imbibed was plotted against time for water imbibing in natural rock materials. The effect of adsorbed organic materials on surface wettability was determined from measurements of rate of imbibition, water saturation and water permeability. INTRODUCTION An understanding of the mechanisms by which water displaces oil from porous media requires an understanding of the role of capillary forces in the displacement process. The capillary forces are determined by properties of the water-oil-solid surfaces. Consequently, some measure of the surface properties of reservoir rocks is necessary if displacement behavior in oil reservoirs is to be predicted from laboratory measurements. Several experimental procedures have been proposed to assign quantitative wettability indexes to reservoir rock surfaces. The most recent of these proposals are those of Bobek, Mattox and Denekas' and Amott.' These indexes are designed to show a continuous variation from the preferential oil-wet to the preferential water-wet systems. They require measuring some property of the rock which is a function of surface wettability. The quantities are measured on unaltered core material and compared with values obtained for known oil-wet and water-wet extremes on the same material. These methods are useful but are semi-empirical in nature. They have the disadvantage that the measured quantities may be functions of other variables in addition to surface wettability. Some understanding of the behavior of water-oil-rock systems may be obtained from studies of the simpler water-air-rock systems. Surfaces of a given wettability are more easily maintained for the latter. Also, certain approximations can be made for the flow of water and air which are not justified for water-oil flow. The theoretical and experimental work discussed in this paper is part of a study of the role of capillarity in the dynamic displacement of air by water. The expec- tation is that observations for the water-air system will lead to generalizations which are applicable to water-oil systems. THEORY Imbibition is defined as that process by which one fluid displaces another from a porous medium as a result of capillary forces only. Differential equations have been derived to describe the displacement of oil by water during imbibition, but these equations have not been solved.".' With certain assumptions, however, solutions are possible for water-air imbibition.

By Michael J. Taylor

Introduction A prime goal in the design and operation of uranium milling waste or tailing disposal systems is to mitigate adverse effects of tailing liquid on the adjacent groundwater. Adverse effects are often defined as modifying the groundwater quality in such a manner as to have detrimental health effects on downstream users. To accomplish this goal, the following three types of systems are employed with regard to the seepage and groundwater aspects of waste disposal: Type I Systems Seepage is allowed to occur unabated from the tailing disposal facility. Detrimental radionuclides and chemical elements are prevented from causing adverse downstream effects by natural purification actions in the subgrade geologic materials and the near zone groundwater. Monitoring is required to assure the predicted natural purification is occurring. The consequences of seepage loss is minimal since the m be predicted with current investigation and analytical techniques and can be evaluated as to effectiveness during operations. Type II Systems Seepage is partially retained in a waste impoundment or leakage from a designed retention system is anticipated. Natural purification is relied on for controlling migration of detrimental radionuclides or chemical elements, or contingency planning is employed to collect and return the tailing liquid to the impoundment. Installation efforts and concern for escape of tailing liquid are greater than for Type I systems, but extra precautions to preclude all seepage are not implemented. Monitoring is required to detect leakage and/or assure the natural purification of escaping tailing fluid. The consequence for accidential excusions are moderate, and will be excessive only if massive system failure occurs. Type III Systems Seepage is totally restricted by a costly system constructed and operated with extra care. Natural

Jan 1, 1980

By E. Miller, J. M. Eldridge, K. L. Komarek

The thermodynamic properties of- liquid Mg-Pb allojs have been determined by an isopiestic method from 18 to 42 at. pct Pb and by a thevmodynumic analysis of the phase diagram frofiz 0 to 100 at. pct Pb. In the overlapping composition range the magneszupn activity values derived by the two methods are in excellent agreement, thus mutually supporting the correctness of the Mg-Pb phase diagram previously determined by the authors and of the acticitzes deriz~ed isopiestically. SEVERAL studies have been made of the thermody-namic properties of liquid Mg-Pb alloys. Wagner and Engelhardt,1 Lantratov,2 Knappwost,3 Sryvalin et al.* and Wilson5 used the electromotive-force method, Scheil and Wolf8 and Schmahl and Sieben" applied the transpiration technique, and the present authors8 utilized the phase diagram to determine the activity of magnesium in the Mg-Pb system. The results of these studies are not in very good agreement and could not be incorporated into a general systematic analysis of the thermodynamic properties of the homologous series of the Mg-Group IV B systems Mg-Pb,8 Mg-Sn,° Mg-Ge,10and Mg-Si.11 The thermodynamic properties of the Mg-Pb system were therefore re investigated by an isopiestic technique which has been developed for similar studies in the Mg-SnB and Mg-Ge10 systems- Lead specimens, contained in iron or graphite crucibles, were heated in a temperature gradient in an evacuated and sealed titanium reaction tube and equilibrated with magnesium vapor of known vapor pressure to form alloys of compositions which depended on their temperatures, the temperature of the magnesium vapor source, and the thermodynamic properties of the system. EXPERIMENTAL PROCEDURE Magnesium (Dominion Magnesium Ltd., Toronto, Canada) of 99.99+ pct purity and lead (American Smelting and Refining Co.) of 99.999 pct purity were used. In the early experiments, Runs 2 and 3, the alloys were contained in uncovered high-purity iron crucibles. Alloys formed in the uncovered iron crucibles had to be chemically analyzed owing to the slight volatility of lead under the imposed experimental equilibration conditions. The compositions of these alloys were determined by a gravimetric analysis of lead as lead chromate. To avoid this problem, the remaining runs were made in covered graphite crucibles machined from high-density (1.92 g per cu cm) graphite rods (Basic Carbon Corp., Sanborn, N.Y.) which had a maximum ash content of less than 0.04 pct. The non- i reactivity of graphite with lead and magnesium has been previously established,' and the experimental procedure has been described in full detail.' In the runs using covered graphite crucibles it was found that the weight increases of the crucibles and their contents after equilibration equaled the magnesium contents of the alloys within the accuracy of the chemical analysis (i0.3 at. pct Pb). Clearly, the small lid openings of the graphite crucibles prevented significant lead losses during a run, and the weight increase was therefore taken as the magnesium content of the alloys. EXPERIMENTAL RESULTS At thermodynamic equilibrium the magnesium partial pressure of the specimens equaled that of the reservoir. Since the magnesium reservoir was always maintained at the temperature minimum of the system, the activity of magnesium of any specimen was given by the ratio of the magnesium reservoir pressure to the vapor pressure of pure magnesium at the specimen temperature. The standard state was chosen as liquid magnesium and the vapor pressure of liquid magnesium

Jan 1, 1968

By K. A. Gschneidner, O. D. McMasters

DgIel-ential thermal, nretallographic, and X-ray paramzetric methods were used to establish the Yb-Pb phase dingram. The terminal solid solubilities in the system are less than 0.2 at. pct. Lead additions lower the 792°C transformation tewzperature of pure ytterbiun~ at 787°C by means of an inverted peritectic veaction. Ytterbium additions raise the 327oC melting point of lead to 329°C by means of a perilectic reaction. Three intermetallic compounds Yb2Pb, YbPb, and YbPb, melt congruerttly at 1246", 1116o, and 740°C. respectively. YbsPb3 forms by a peritectic reacliorz at 1250°C. YbzPb crystallizes in the PbCh (C23) type structure and the orthorhombic latliceo constants are a, = 7.478. bo = 5.225, aud C0 = 9.549A. YbsPbs crystallizes in the hfnsSi3 (D8a) type structure. The hexa~nal lattice constants for this phase are a, = 9.325 and co = 6.92d. YbPbl crystallizes in the cubic AuCU3 (Ll2) type structure with a: = 4.8628 + 0.0008A. YbPb is diwrorphic with the structure change occurring al 507°C upon healing. The crystal structures of the two forttzs were not determined. Eulectic reactions occur at 5.1 at. pct Pb and 769oC, 41.5 at. pct Pb and 1086oC, and G8.0 at. pct Ph and 717°C: RELIABLE information concerning the alloying behavior of most of the rare-earth metals is scarce. A systematic study of the rare earth-lead alloy systems now in progress is an effort to supply such information. Determination of the phase diagram of the Yb-Pb alloys is the first step of this study. Variations in the valence of normally divalent ytterbium may be studied by comparing the characteristics of the Yb-Pb alloys to those of the trivalent rare earth-lead and of the divalent alkaline-earth-lead systems. Of particular interest are the melting temperatures of the intermetal-lic compounds since these are known to be high relative to the melting points of the constituent metals. Crys-tallographic and magnetic susceptibility data for the rare earth-lead alloys are to be included in the comparative study. Results from this and subsequent investigations should provide a better understanding of alloy formation. EXPERIMENTAL PROCEDURE Materials. The major impurities in the ytterbium and lead used in this investigation are listed in Table I. The lead was obtained from Cominco Products, Inc., and was specified to be 99.99 pct pure. The ytterbium was prepared in this laboratory by the lanthanum reduction of the oxide followed by a distillation of the ytterbium. Alloy Preparation. The alloys were prepared by

Jan 1, 1968

By B Cronin, M Gao, M F. Young

Fine grinding technology has become extremely important for Mount Isa Mines Limited in the last decade for flowsheet development for the McArthur River deposit and in rejuvenating the Lead-Zinc Concentrator at Mount Isa. Regrinding products with 80 per cent passing seven microns and 12 microns were required, respectively, for the McArthur River ore and the Lead-Zinc Concentrator at Mount Isa. Development of the ISAMILL, a horizontal stirred mill with a gross mill volume of 4000 litres (a net volume of 3000 litres), has been successful in delivering the required grinding product sizes with an energy consumption acceptable to a mining operation. The ISAMILL performance for processing both lead and zinc streams at Mount Isa is discussed in this paper, including the milling energy efficiency, the media wear and the size-by-size recovery data for one flotation process following the fine regrinding stage. The potential use of the ISAMILL technology at various phases of the mining cycle is also discussed.

Jan 1, 1998

By C. H. Jr. Herty

ALMOST every metallurgist who has given the Howe Memorial Lecture has had a personal contact with the distinguished gentleman to whose honor this hour is devoted. Unfortunately for me, such personal contacts were not possible. However, in the preparation of a thesis on the open-hearth process, one of my earliest tasks was to make a survey of the literature, and it was from Professor Howe's Metallurgy of Iron and Steel that I drew a number of references to previous work which formed the foundation for my reading. In his volume there is such a complete exposition of the then current thought on the subject of slags and on their role in the elimination of phosphorus from steel that I feel no hesitation in discussing in this Howe Lecture the subject of "Slag Control." In the present era of close specification, the drive for uniformity of product, and the close inspection of the product and of the cost sheet, the utmost efforts must be made to control the steelmaking variables to the best advantage of the steel producer. One of the major variables is the slag in the furnace and its effect upon the composition and quality of the metal. What advantages are to be gained from slag control? In the broad sense the advantages must be tremendous, because the very foundations of good steel melting are based on "shaping up" the slag to a point where, with proper temperature, the heat is ready for the final additions. Every melter works toward these ends through his experience with innumerable heats of steel. The elimination of undesirable constituents such as phosphorus and sulphur is entirely a matter of slag composition and physical nature, a point well known for over half a century. The role played by the slag in assisting in proper heat transfer from roof and flame to the steel has been equally well known. In more recent years there has come the problem of oxygen control in the more accurate gaug-ing of additions for making high-grade rimmed steel for the new strip mills, and in the deoxidizing additions for grain-size control and cleanli-ness of forging steels, both carbon and alloy. In this problem the oxidiz-ing characteristics of the slag are of prime importance.

Jan 1, 1940

By J. F. Havard

Gypsum is a useful industrial mineral found abundantly on the earth's crust. It is inexpensive to mine and process, and its calcined products have a wide range of readily controllable properties such as strength, density and setting time. It has proven to be such a useful material indeed, that ten American companies, operating some 57 calcining plants in 25 states in 1958, produced or imported in that year a total of 13,649,000 tons of the crude mineral valued at $39,361,000, which they then converted into manufactured products with a value of $329,070,000. Gypsum (CaSO4.2H2O) is calcium sulfate with two molecules of combined water, which are responsible for most of its useful properties. It is closely associated in most deposits with anhydrite (CaSO4), which contains no combined water and has limited commercial value in the United States. Man has long recognized the useful qualities of gypsum. It was utilized by the Egyptians in the construction of the pyramids and, later, by the Romans for important structures. Many of the ancient peoples prized gypsum for artistic and ornamental purposes, carving statuary from alabaster and making casts with plaster. The tabular variety, selenite, was used for windows, and the light transmitted through these windows reminded people of light from the moon (selene), hence the name selenite. The use of gypsum continued through the Middle Ages and into modem times. Benjamin Franklin was a famed exponent of gypsum because he applied ground gypsum to clover fields in the form of large letters which later read, in the more luxuriant growth, "land plaster used here." Gypsum is still used as an effective conditioner for some soils, but in recent decades, particularly in North America and Europe, it has become much more important as a major material for the building industry. Description Gypsum and anhydrite are closely associated minerals. Gypsum is found in a number of forms: massive rock gypsum, alabaster, selenite, satin spar, and gypsite. Anhydrite is found as massive rock or as smaller bodies or isolated crystals included in gypsum. Massive Rock Gypsum comprises most of the commercial gypsum and occurs as a sedimentary rock, interbedded in most places with shale, limestone or dolomite. This rock is soft and crystalline. Its color is white or shades of gray, pink, yellow, brown or other colors. Alabaster is a pure, compact and fine-grained variety suitable for use in sculpture or turning into artistic forms; it may be white or selected for attractive coloration. Selenite is gypsum crystallized in flat, transparent, flexible foliated plates, found in clays or in surface vugs in gypsum. Satin Spar is a fine silky fibrous variety with the axes of the crystalline fibers perpendicular to the vein or joint in which it has formed. Gypsite is an earthy mixture of gypsum with clay and sand in secondary formations; it is sometimes useful as a soil conditioner and has been used in making base-coat plasters. Pure gypsum contains 20.9 pct combined water, 46.6 pct sulfur trioxide (SO3) and 32.5 pct lime (CaO). Standard specifications (American Society for Testing Materials Designation C 22-50) read that minimum purity for material to be called gypsum is 70 pct CaSO4.2H20. Most of the commercial gypsum is 85 to 95 pct pure as produced. Impurities in

Jan 1, 1960

By P. W. Ramsey, E. J. Boyle, E. A. Anderson

ONLY a few zinc-rich alloys are in commercial use today, and these depend largely upon solid solution effects for their desirable properties. Typical examples are rolled alloys containing about I per cent of copper, with or without additions of elements such as magnesium,1 and die-casting alloys containing about 4 per cent of aluminum with small amounts of magnesium and sometimes copper.2 A number of elements are capable of forming alloys with zinc, which do not enter into solid solution except in limited degree. The present paper considers one such system, zinc-titanium, in which alloys having potentially useful properties in the rolled form were found. ZINC-TITANIUM SYSTEM The zinc-rich portion of the zinc-titanium diagram, as determined by standard methods in this laboratory,3 is shown in Fig. I. The portion of the diagram of significance in the present work extends from 0 to about 0.5 per cent titanium. Gebhardt4 places the eutectic at 0.45 per cent, but the evidence in favor of the composition given in Fig. I is considerable. The solid solubility of titanium in zinc is very low indeed and possibly places these alloys in a somewhat different category from the commercial alloys previously mentioned. ALLOY PREPARATION All of the alloys used in this work were prepared with titanium metal of 98.9 per cent purity. In most cases high-purity zinc (99.99 per cent) was used but sufficient work was done later to show that zinc of about high-grade composition would yield approximately equal results. Best practice in alloy manufacture seemed to be to prepare a zinc-titanium hardener by adding about 4 per cent of titanium metal to molten zinc and holding under a boric acid cover, with frequent stirrings, at 750°C. until the titanium had dissolved. The desired titanium content could readily be obtained in the final alloy by adding the calculated amount of this hardener. The alloys proved to be quite stable in composition, unless overheated, and, with reasonable temperature control, required no cover or flux to prevent loss of titanium content by oxidation. HOT-ROLLING TESTS Three alloys containing, by analysis, 0.05, 0.12, and 0.23 per cent titanium were selected for preliminary study. Slab cross sections revealed a marked grain refinement* (Fig. 2) in the two alloys of highest titanium content. Cast unalloyed zinc has a columnar grain structure similar to that shown for the alloy of lowest titanium content but without the scatter of small equiaxed grains at the center.

Jan 1, 1944

By H. T. Hildage

Although Greater New York does not bear any resemblance to a great mining district, the mining operations that are being conducted in and about the city are both extensive and interesting in character. With regard to the extent, it may be mentioned that, at present, there is more dynamite used in New York than in any mining district in the United States; that there are under construction about 38 miles of tunnel, and that 66 miles more are projected, most of which must be constructed .in the near future; that since 1903 at least 2,000,000 tons of earth has been removed in underground work, in addition to about 3,500,000 tons that has been removed in open-cut in connection with tunnel-work, and many times this quantity that has been removed in excavating foundations for buildings not connected with tunnel-work; and that there are to-day probably more than 5,000 men engaged in mining-work in and about New lrork City. These undertakings include almost every operation connected with underground work, from exploration by means of trench and boring, to the sinking of large shafts and the driving of large tunnels through every kind of ground from hard rock to soft, semi-fluid silt and quicksand. It is proposed in this paper to give a general description of some of the methods and appliances used in the opening-up of a " mine " in a large city, and a brief description of some of the &'mines" now being developed in New York, connecting as far as possible the methods described with the particular work for which they were designed, in order to give a general idea of the

Jan 1, 1908

By J. J. Rutledge

I. Description of the Clinton Ores and Associated Rocks. The Clinton rocks in Stone valley comprise (1) thick layers of deep-red shale, (2) layers of reddish-gray shale interspersed with beds of sandstone and thin beds of extremely fossiliferous limestone, and (3) yellowish-gray shales alternating with thin layers of olive-colored shales. These layers of shale are all very thin and are at no point massive.' A bed of gray-white sandstone varying in thickness from 12 to 30 ft. occurs in the upper portions of the Clinton shales. This is called the ore sandstone, a name given to it by Rogers and adopted also by the Second Pennsylvania Geological Survey. It is the surest guide to the presence of the iron-ore bed, which lies below its lower edges at distances varying from 10 to 20 ft. This ore sandstone, in the valley, lies generally at very low inclinations, but often is locally subjected to considerable changes in dip. At its outcrop this ore sandstone weathers very easily and yields a rather sparse crop of stone, composed of dirty, iron-stained boulders. Upon the roads these boulders are quite well rounded, and bear fragments of crinoid stems and other fossil forms. The ore sandstone exhibits at many points evidences of former movements in this very great thickness of the shales, and as it is the only stratum in this series competent to transmit and record stresses due to structural movements, its evidence is of considerable importance in determining the occurrence of movements in times past.

Jan 1, 1910

By A. Kaufmann, B. Cullity, G. Bitsianes

T0 determine the bulk of the phase diagram, techniques for melting, thermal analysis, heat treatment, metallography, and X-ray diffraction that have already been described were used.' It proved difficult to get definitive results for most of the alloy system because of the large number of compounds, their high melting points, and their extreme brittle-ness which made metallography difficult. The final phase diagram, essentially as shown in Fig. 1, was issued with considerable trepidation.' The phase relationships at the two ends of the system were defined with satisfactory accuracy. In the central region between U,Si, and USi, there was great uncertainty concerning the melting points and even the composition of the compounds. At the uranium end of the system, it is quite clear that a eutectic exists at about 985 °C and approximately 8 or 9 atomic pct Si. The a-to-8 transformation is not appreciably altered by silicon, but the 8-to-y transformation is raised to about 795°C. There is appreciable solid solubility in y-uranium, as demonstrated by the micrographs of Fig. 2. The occurrence of the E phase was not suspected at first, since the alloys as melted and furnace cooled gave no X-ray diffraction or thermal arrest indication of it. However, suitable metallography revealed a rim around each of the compound particles as shown in Fig. 3. Heat treatment above 600°C revealed that the rim was another phase which formed by peritectoid reaction between uranium and U,Si,. This reaction proceeds slowly and it is difficult to get it to go to completion. Consequently, there is some uncertainty concerning the exact composition of P and the exact peritectoid temperature. On the basis of various metallurgical studies, it was decided that the most probable composition for t was about 23 atomic pct Si. Metallographic examination shows the closest approach to a single phase at this composition. Likewise, density and hardness measurements of heat-treated alloys shown in Figs. 9 and 10 show a change in slope at 23 pct Si. This is revealed most clearly by plotting the difference in hardness or density between chill-cast and heat- treated alloys as shown in Fig. 4. Zachariasen2 was able to index the diffraction lines of P and to determine the arrangement of the atoms in the unit cell. He concluded that the composition must be US. However, it is felt that the metallurgical studies are reliable and that Zachariasen's X-ray work does not furnish positive proof that the P phase exists exactly at the stoichiometric composition U3Si. There are many instances in alloy systems where a phase does not occur at the composition dictated by the molecular structure. It is possible that the chemical analyses used in the present work were subject to some systematic error. This seems unlikely, however, since recent work in several laboratories seems to show excess compound at 25 atomic pct Si.

Jan 1, 1958

By McQuiston. F. W., E. C. Tveter

Sulfide mineral flotation has been applied to all naturally occurring sulfides and several synthetics. Of even more importance is the fact that economic separations are now being made between sulfides of essentially all the different metals. The variety of methods and minerals involved in such practice make it difficult to characterize them except in terms of general factors which influence the practices used. Ore grade and mineral composition are the major factors determining the processing method and the extent to which processing must be carried to achieve optimum economic return for a given ore. Since the choice of treatment is also affected by such factors as mine location, shipping charges, smelter schedules, each ore is a separate problem even though mineralization may be similar; The dissemination of minerals in the ore naturally determines the fineness of grind required for liberation. However, since grinding costs are a major part of most milling costs, emphasis has been placed on means of rejecting gangue minerals at the coarsest size possible. This has led to increased flotation of middling products or bulk concentrates for subsequent regrind and retreatment. Reagent development has also played an important part in present plant practice. Relatively few new frothers and collectors have found application during the past 25 years and many have disappeared. In general practice, re- agent combination choice is now fairly consistent with the type of collector being chosen on the basis of the mineral to be floated, the frother on the basis of pulp alkalinity, and the modifiers primarily on the basis of minerals to be rejected. REPRESENTATIVE FLOTATION PLANTS The milling operations described in this chapter have been selected primarily to illustrate these differences in ores and processing methods for the major types of ore minerals. The compositions of these minerals are shown in Table 1. These concentrators were chosen as representatives, both on the basis of geographic location and mineral content of the ore treated. At least one mill is included from each of the major producers, but the primary object was to show the practice employed for the various ore minerals and the different approaches to the middling problems encountered. The individual plants which have contributed data to this study are listed in Table 2, with a summary of their operating data, and are discussed in the order shown.

Jan 1, 1962

By Brad W. Taylor

"During the past several months, I have introduced to civil and structural engineers an innovative solution for the integrity testing of concrete using the Thermal Integrity Profiler (TIP) Wire Cable System by Pile Dynamics. While in the process of “educating” highly-trained professionals about a technological breakthrough, I ended up being educated myself about their needs for quality control/quality assurance (QA/QC). With that in mind, I would like to focus on their two key areas of concern:• How complex is the TIP installation process?• How does the QA/QC engineereffectively analyze and report TIP test results?A few months ago, during a discussion with a senior QA engineer, he asked a question that stopped me in my tracks: “Why should we do foundation testing at all?” Turning it around, I asked, “Why wouldn’t QA/QC personnel want to know everything they could about their critical infrastructure foundation?” Honestly, I didn’t answer his question nor did I fully comprehend what he was trying to say. With his experience, the engineer understood that there has not been an integrity test or a combination of integrity tests that could deliver an inside the cage and outside the cage (cover) complete data set that would provide a definitive profile of the entire shaft. Crosshole sonic logging (CSL) becomes more effective the larger the diameter of the shaft becomes, with a maximum effectiveness between 70% and 80%, but does not provide any data of the integrity of the shaft beyond a straight line between CSL tubes. Gamma-gamma logging (GGL) provides qualitative information about the concrete surrounding the GGL tube and device, and it provides information about a small percentage of the drilled shaft concrete near its outside edge."

Jan 1, 2017

By W. H. Emmons

Most mineral deposits change as they are followed downward on their dips. Some of these changes are due to primary arrangement; different ores were precipitated at different depths when the deposits were formed. Other changes are due to weathering or secondary enrichment. The chief changes resulting from weathering, in the main, are understood and standard changes are recognized. The processes are relatively simple. They take place at ordinary temperatures and pressures and can be duplicated in the laboratories. Moreover, there are thousands of deposits available for study, because the processes take place near the surface where the development of mines is begun. The changes due to primary arrangement of the deposits of the metals are not so well understood. Deposition has taken place at higher temperatures and our knowledge of the chemistry of the processes leaves much to he desired. Very few experimental data are available. The deposits, moreover, offer fewer examples because many mines are not developed to depths where the changes can be studied and a change to unprofitable material usually results in stopping work. Most students of ore deposits now accept, as confirmed, the hypothesis that nearly all lodes and related deposits were formed by solutions originating in intrusive igneous masses. Outward from these masses, the deposits at many places are grouped in zones and the arrangement noted from the intrusions outward are commonly the reverse of the changes noted from the surface downward in a single lode. A study of the changes in groups of deposits, from the parent intrusion outward, will throw light on the changes to be expected in a single lode downward. Recause the changes in series of deposits from the intrusive outward may all be observed near the surface, where more data are available, it is possible to increase the number of examples many fold and to apply the statisttical method of study with greater confidence of avoiding error. It is not everywhere possible to identify the parent igneous body to which a group of ore deposits are related. Several kinds of criteria are available; certain groups are superior to others. By applying the

Jan 1, 1924