Search Documents

In the process of mining the lower seam in a multi-seam operation, a lot of oblique fract- ures appeared in the upper seam which was in the equilibrium zone. These fractures closed soon after the lower face line passed. Despite the occurrance of some degree of undulations, and and step-like unevenness, the upper seam was subsequently extracted without difficulty. When attempting multi-seam extraction, from the height of the equilibrium zone, the minimum distance between seams in ascending mining should be predicted. By analysing roof con- vergences data and the geometrical configuration of subsidence profile, it was found that the minimum safe distance for ascending multi-seam mining depends on the mining height of the lower seam and the properties and structure of the inter-stratified rocks.

Jan 1, 1986

By E. Hosca

Alternative tailgate loading conditions due to conventional and conventional/yield pillar combinations were evaluated to define roof loading. In order to isolate different loading situations, the tailgate entry was considered as part of the roof-pillar-floor system, which is controlled largely by the structural integrity of each member. A data bank of case studies was compiled, which contains details of roof and floor lithology, structure, support, and mining data, including any failure modes. The range of loading conditions that any tailgate can be subjected to was identified to form the basis of numerical modeling. Numerical modeling was then conducted on tailgate openings to determine roof, floor, and rib responses, including failure modes to a variety of loading conditions. Trends developed from the numerical modeling were modified using field data to form the basis for support evaluation and application. The effects of support were modeled numerically to determine optimum load capacity and points of application for reducing the potential for entry failure.

Jan 1, 1994

By Bruno C. Boik

INTRODUCTION Cost Management is the evaluation and control of project scope, budgets, and costs with the objective to minimize costs and maximize the benefits to be derived from the use of project resources in conformance with Criteria stipulated or approved by the Owner. In order of importance, Cost Management is one of the most prominent Project Management functions because of its impact on the financial success of the venture. Cost Control and Cost Accounting are essential parts of Cost Management. The principal objectives of Cost Control are to monitor project commitments and expenditures, and measure performance for the detection of variances from acceptable standards and from control budgets so that timely action can be initiated to minimize costs. Cost Control is evaluation of current costs and projection of future costs, rather than the reporting of actual costs. Cost Control is not Cost Accounting. The primary objectives of Cost Accounting are the determination, classification, analysis and reporting in useful detail of actual costs. Following are some considerations on Cost Management and Cost Control as practiced by Owners and Contractors of industrial projects, Mining and Metallurgical projects in particular. COST MANAGEMENT Functions Conforming with the requirements of Owner's Criteria, the principal Cost Management functions are to • evaluate estimates of project costs and establish budgets for a scope of work and schedule; conversely, evaluate the scope of work that can be executed most effectively within a budget and schedule. • promote investigations and comparative evaluations of alternate designs and plans to find the most cost effective way to execute a project and minimize its operating costs. • based on Cost Control and Cost Accounting input, evaluate and initiate appropriate actions to correct deviations from approved budgets. assess project economics, the effect of changes on project economics and, if necessary, revise Project Criteria to modify their impact on costs.

Jan 1, 1986

By John Fritz

Gentlemen of the American Institute of Mining Engineers : I desire to thank you sincerely for the distinguished honor you have conferred upon me by electing me to the presidency of this society, a position which in the past has been filled by some of our most distinguished and ablest members, men eminently qualified by education, practical training and a business ability which has enabled them not only to fill the position with credit to themselves, but as well with honor to the society. In deference to a custom long established, by which the presidentelect is expected to read a paper on some subject with which he is more or less familiar, I have thought that a brief review of the methods employed in the manufacture of iron, as witnessed by myself, and reaching back to 1838, would interest some of our older members and give our younger ones a glimpse into the trials and difficulties encountered in those early days by the pioneers in this great industry. In 1840, 12 to 20 tons of pig-iron was the make of a furnace per week—at this time from 1200 to 2000 gross tons. In 1840, 3 to 4 tons No. 4 wire rods per turn. They have lately made 176 gross tons in 11 hours. In 1840 I have not the quantity of puddled iron made; but it was

Jan 1, 1895

As bizarre an example of competitive salesmanship to be imagined took place last June in Western Australia. A half dozen world renowned mining groups received a Japanese iron and steel investigatory mission. Geologists, engineers and businessmen, all specialists in iron ore, representing elements of the Japanese government and steelmakers, politely grilled each iron ore group for technical information and plans for property development. At stake were sales contracts with Japan for many millions of tons of iron ore. Since approximately two dozen visitors were involved, it was necessary to divide them into four groups for dispensing information, transportation and accommodations at the remote exploration camps. In a continent noted for its wide open spaces, the hinterland of Western Australia is spectacularly lacking in settlements. The state has better than one third of Australian land and statistically 0.8 persons per sq mile. In reality, however, over 400,000 of the 800,000 population reside in Perth. Under such circumstances, properly receiving and feting these important visitors would seem to be difficult but the competing exploration groups vied ingeniously to outdo each other in hospitality.

Jan 10, 1964

By A. E. M. Warner, A. Vahed, P. J. Mackey

In the decade 2002 to 2012 some 6.7 million tonnes of new copper concentrate production capacity was brought on line, corresponding to 2 million tonnes of contained copper. This increase in concentrate supply necessitated the commissioning of a number of new copper smelters as well as the modernization and/or expansion of existing plants to meet the demand. This paper gives an overview of the copper extractive industry, reviews recent copper production trends and changes in the copper industry, including an examination of pyrometallurgical and hydrometallurgical technology developments. WorleyParsons has supported a number of the projects involved in these developments and this role is briefly discussed. The paper introduces a number of ideas related to possible future directions of the copper industry.

Jan 1, 2014

By Aziz NI, Guo H

Most of the existing models of the mechanisms of drilling and cutting processes are oversimplified in both stress state and failure criterion. On the other hand numerical modelling techniques are a more versatile method with great potential for development. In reviewing drillability and predicting performance of excavation machines the empirical tests, which simulate the physical breakage action in excavating processes are seen to be the best in terms of penetration rate predictability. Future methods of determination of drillability should concern the breakage characteristics and rock abrasivity involved in the two basic types of attack, i.e., percussive and rotary drilling.

Jan 1, 1988

By Syd S. Peng

Full-face shield leg pressures in a longwall panel for a three-month period were collected and analyzed. The pressure data were presented in the following forms: full- panel full-face shield pressure, individual shield pressure, full-face shield pressure, full-panel time-weighted-average pressure, and relationships among setting pressure, final pressure and pressure increment. Although shield pressure varies from shield to shield and from cycle to cycle, the setting pressure and face advance rate do control the 6nal pressure and time-weighted average pressure.

Jan 1, 1997

By A M. Robertson, R Lefebvre

Air movement and associated oxygen transport through waste rock dumps has the potential to significantly enhance the rate of oxidation of pyrite-bearing material. While this is a desired outcome for most heap leach operations, airflow in waste rock storage facilities can result in significant increases in generation and acceleration of acid rock drainage. Hence, a good understanding of internal airflow through waste rock dumps is required to control ARD and minimise any associated liability. The principal mechanisms contributing to airflow and oxygen transport in a waste rock pile include: diffusion; advection due to a thermal gradient (chimney effect) and/or wind pressure gradients; and advection due to barometric pumping. While diffusion is typically limited to a near-surface zone of a few meters depth, advection and barometric pumping have the potential to move air (and oxygen) to much greater depths into the pile. In general, the more permeable the waste rock material, and the greater the height-to-width ratio of the waste rock pile, the greater is the potential for advective air movement. The reactivity of the waste rock material as well as the coarseness (hence air permeability), and the spatial variability of these properties within a pile, have a strong influence on the magnitude of thermally induced advection. In contrast, air movement due to barometric pumping is controlled by the waste rock porosity, changes in ambient air pressure and the heterogeneity of air permeability of the waste rock dump. Results of field monitoring and numerical modelling using TOUGH AMD are presented to illustrate the concepts on air movement in waste rock piles discussed in this paper. During the design and construction phase, airflow can be controlled by judicious placement of reactive waste rock and use of selective placement techniques to control the internal structure of the waste rock facility (eg introduction of horizontal layering, prevention of inclined, high-permeability, channels (æchimneysÆ)). Several closure measures are available to minimise airflow including: placement of a low-permeability cover to reduce air entry; and placement of a non-reactive cover material to isolate reactive material from the zone of active airflow and/or regrading of the waste rock pile to obtain a geometry and internal structure less susceptible to advective airflow.

Jan 1, 2003

By Christopher Mark

The demographics and safety record of the pillar retreat segment of the U.S. coal industry was analyzed using statistics collected by the Mine Safety and Health Administration. Pillar recovery is practiced primarily by mines in Appalachia and the Midwest. Using 1993 data, the accident rates and productivity of a large sample of pillar re- mines were found to be similar to other room-and-pillar mines in the same geographic areas. Pillar recovery apparently accounts for about 10% of all U.S. underground production, but has been associated with about 25% of the mf and rib fatalities during 1989-96. However, of the 28 fatalities that were analyzed, only 4 occurred for which no citations were issued for violations of mining law. Nearly one- half of the fatal incidents occurred during the mining of the last lift or pushout. All four no-citation incidents occurred during the removal of the last lift during a "Christmas tree" extraction sequence.

Jan 1, 1997

By Paul T. Allsman

THIS CHAPTER reviews the highlights of developments in mining technology during 1956 and presents a special report on the design of mine openings in stable ground. This special report is presented each year in an endeavor to stimulate use of the scientific approach to the solution of problems related to mining technology. Assuming that the literature on mining technology reflects trends in mining, it appears that two areas of activity were given most attention in 1956. One was research on mining technology,4 and the other was improvement of transportation, particularly trackless transportation, both at surface and underground mines.

Jan 1, 1958

By J. P. Rees

Describes methods of dust-sampling such as weighing the dust caught on cotton-wool, the sugar tube, konimeter, circular konimeter and the thermal precipitator. Covers the work of mine dust inspectors, the Miners' Phthisis Prevention Committee and the Chamber of Mines Dust Department.

Jan 1, 1947

By Helmer Hedstrom

GRAVITY surveying with the torsion balance or the pendulum for ore prospecting purposes has generally not been considered practical or even possible. It is the intention of this paper to show that a fast and sensi-tive gravimeter can be very useful in ore prospecting, as an auxiliary to the electrical and magnetic instruments. A number of gravimeters have been constructed and put in practical use in the last seven or eight years; for instance, by Ising, Lejay-Holweck, Haalck, Hartley, Thyssen, Noergaard, the Humble Oil and Refining Co. and the Gulf Production Co. Their main application, apart from their use for geodetic surveys, has been for structure mapping in oil prospecting. There is no record that any of them have been used for ore prospecting. About the middle of 1934 the Boliden Mining Co., in Sweden, began experiments in constructing a static gravity meter sensitive enough for ore prospecting. Calculations and considerations that will be discussed later in this paper showed that this would necessitate an accuracy in the measurements of 0.1 milligal-roughly, one ten-millionth part of the total force of gravity. The first successful practical field tests of the instrument were made in January 1936. About the middle of 1937 the Boliden gravimeter was perfected. Ore prospecting with this instru-ment is now regular practice in Sweden, especially for the testing of indications given by geoelectric and magnetic methods.

Jan 1, 1938

By Ellis Clark

During the winter of 1877-78 the Glendon Iron Company, by the advice of the superintendent, Mr. Frank Firmstone, decided to make the experiment of exploding a heavy blast of gunpowder in their limestone quarry at Cedar Hill, Palmer Township, Northampton County, Pennsylvania. The amount of limestone used in the five furnaces of the company is about 60,000 tons per annum, and it was thought that with successful results? this entire amount or more would be thrown down at a single operation, disintegrating the mass to a greater or less extent, and obviating the necessity of blasting and boring the rock from the face of the cliff, both of which operations are slow, and therefore, costly. The rock at the quarry is Auroral limestoue, or No. 2 of the old Survey. No fossils have ever been found in the quarry, nor in the immediate vicinity. The nature of the rock varies considerably in

Jan 1, 1879

The St George orebodies are situated within the tectonically disrupted eastern limb of the Boogardie Syncline.Highly disturbed rafts of banded chert formations occur within a sequence of felsic volcanic tuffs. The chert forms the hostrock for the gold mineralization.The gold distribution within the irregular and narrow banded chert formations is erratic and patchy. The average gold content of the two orebodies is between 3 - 4 g/t Au.Economic mining of these relative small, irregular and low grade St. George orebodies can be carried out by using a highly selective mining method.The highly selective mining method uses an excavator as the principle mining tool. Blasting, breaking and loading of the rocks is done in a different way than by using a front-end loader as with the conventional mining method. Simple, and therefore cheaper, blasting breaks the rocks and lifts them up without major displacements.

Jan 1, 1984

By D. W. Fuerstenau, S. Raghavan

This paper presents a brief summary of some of the thermodynamic aspects of flotation processes. Thermodynamic considerations that control interfacial and wetting behavior in mineral/water/air systems are discussed. Particular attention is given to the thermodynamics of collector adsorption.

Jan 1, 1976

By S. Özgen

In this study, the possibility of beneficiation of chromite tailings in the Uckopru/Fethiye-Turkey region by a combination of hydrocyclone and multigravity separator (MGS) was investigated. The two significant operational parameters of hydrocyclone, which were diameter of the apex and diameter of the vortex, and the three significant operational parameters of the MGS, which were drum speed, tilt angle, and wash water, were varied and the results were evaluated with the central composite rotatable design. In order to produce a chromite concentrate by hydrocyclone and MGS, mathematical model equations were derived by computer simulation programming, applying the least-squares method using Minitab 15. Second-order response functions were produced for the grade and recovery of chromite concentrates.

Jan 1, 2012

In the hard rocks of the Nordic countries of Norway, Sweden and Finland underground works have a long tradition. Today the subsurface has been taken into use for a wide variety of purposes. In this paper only the more uncon- ventional examples are described such as caverns for drinking water, sand bunkers, molasses silos, wine and liquor stores, cold stores, heat storage, waste disposal and state archives. The particular use of unlined high pressure tunnels and socalled air-cushions for hydropower schemes is discussed. The dual use of subsurface air-raid shelters for sports activities seems to be a special Nordic tradition. Some cost figures are given and the advantages of using the underground is Discussed.

Jan 1, 1987

By C. J. Hall

An investigation of multi-shaft airflow problems by the author in 1976 (1) was presented in the hope of arousing considerable written comment, but in fact-. only one contribution (2) was forthcoming. The investigation in this paper is taken several stages fur¬ther, because the matter is of major importance in many American hard rock mines with complex networks extending over thousands of meters vertically. The examples used have all been generated thermodynamical¬ly and checked by motive column (denisty) calculations. Dry air has been used to reduce the amount of time spent on the rather complex calculations, but it has been shown (3) that the principals developed apply equally well to air/vapor/water mixtures. Initially the subject is investigated using both thermodynamic and motive column analyses. The latter part of the paper concentrates on a motive column presentation. Both methods are, of course, equally valid and give identical answers to any situation when correctly applied, as is shown in the worked examples.

Jan 1, 1980

By Michael G. Li

Prediction of acid rock drainage (ARD) for low-sulphide, low-neutralisation potential (LSLNP) mine wastes is methodologically different from that for normal sulphidic mining wastes. In this paper. LSLNP wastes are conveniently defined as those with S2 < 1% and ABA-NP2 < 20 kg CaCO3 eq/t. The distinctiveness of ARD prediction for LSLNP materials originates from their frequently low oxidation rates and is mainly attributable to two reasons. First, the utilisation efficiency of available carbonate neutralisation potential (CNP2) rapidly deteriorates when the sulphide oxidation rate per unit mass of waste drops below a certain level. Reducing the flushing rate of a waste has the same effect as increasing the oxidation rate. Second, silicate neutralisation becomes increasingly important as oxidation rates diminish, and can no longer be ignored in LSLNP materials as it often is for normal sulphidic mine wastes. In this paper, the effects of oxidation rate, pore gas CO2 partial pressure, and flushing rate on ARD prediction for LSLNP materials are theoretically demonstrated with the help of modelling using the computer program MINTEQA2. A new methodology for ARD prediction for LSLNP materials is presented in terms of a prediction procedure. Finally, a case study is given to validate some of theoretical aspects discussed and to illustrate the use of the newly proposed ARD prediction procedure.

Jan 1, 2000