Search Documents

By Adam Gerondale, David Hemstreet, Lisheng Shao, Kenji Yamasaki

"Foundation soils of a proposed single-span bridge over a busy railroad in Anchorage, Alaska included a layer of sensitive, non-plastic to low-plasticity silt. Slope stability analyses showed that, without ground improvement, the proposed abutments would not be stable immediately following the design earthquake due to the liquefaction of the sensitive silt. Wet soil mixing was selected to mitigate the liquefiable soils and assure abutment stability because: (i) it is a non-vibratory method and can be used for areas adjacent to the railroad tracks and underground utilities, as well as in areas not sensitive to vibration; and (ii) preand post-ground improvement testing, such as SPT or CPT, is not required. Eliminating the liquefaction hazard at the site also allowed for the abutments to be economically supported on shallow spread footings. A total of 511 soil-cement columns were constructed at the two abutments, each with a diameter of 8 feet (2.4 m) and an average length of 20 feet (6.1 m), extending from about 30 to 10 feet (9.1 to 3.0 m) below finished ground elevation. The columns were laid out in a shear wall pattern (in the longitudinal direction of the bridge) to increase stability under the loading by approach embankments.INTRODUCTIONAlaska Department of Transportation and Public Facilities (Alaska DOT&PF) is currently constructing West Dowling Road Overcrossing in Anchorage Alaska. It will be a single-span, steel box girder bridge approximately 200 feet (61 m) long and 100 feet (30 m) wide. It will have approach embankments, about 40 feet (12 m) high, on both sides. It will carry the new extension of West Dowling Road over double tracks of Alaska Railroad and Arctic Blvd. Foundation soils of the abutments consist of surficial fill and peat layer underlain by soft silt which is likely to liquefy and lose strength under shaking by a design earthquake. Both deep and shallow foundations were considered to support the bridge abutments. The design team pursued the option of improving the foundation soils and using shallow footings. Several ground improvement methods were evaluated, out of which wet soil mixing was selected as the best option.In situ wet soil mixing (hereinafter simply soil mixing) is mechanical mixing of soil in its location with cement slurry and produces soil-cement (soilcrete) columns that are stronger, less permeable, and less compressible than the original soil. Soil mixing is used for various applications including reinforcement of soft soils, excavation support, liquefaction mitigation, cutoff walls, etc. This paper presents a case history of soil mixing successfully used to improve foundation soils of bridge abutments to allow the use of spread footings."

Jan 1, 2015

By Gianni Shena, Francesco Montanari

"Recent improvements in the resolution of X-ray computed tomography (CT) make it a promising alternative to traditional time consuming, error prone laboratory procedures for mineral liberation analysis, such as heavy liquid fractioning and measurements on polished sections. All indications are that in a few years CT will be well-established in many laboratories as a rapid technique for accurate liberation studies. In this scenario it would be able to provide liberation spectra or washability data in tens of minutes following sampling. However, although CT is a fast evolving technology, its on-line application is unlikely in the foreseeable future.Dual-energy (DE) radiography is another X-ray technique originating from non-destructive evaluation (NDE) and medical fields, which allows retrieval of the volumetric content of valuable components from two-phase particles in a fraction of second. Two radiographic images at different X-ray energies of a single particle or a monolayer of particles are taken in short time sequence. The thickness of the two phases is calculated particle by particle by image subtraction, whereupon particle grades can be derived. The development of the method for on-line applications requires the presentation of non-overlapping particles in the gap in the X-ray source detector measurement couple. Straightforward extension of the principle to multiphase systems is not possible. The paper reviews the state of the art of these two techniques as applied to mineral liberation problems."

Jan 1, 2003

By Shawn A. Cefalu, Matthew J. M. Krane, Kent J. VanEvery

"Segregation during electroslag remelting (ESR) of a nickel-chromium-molybdenum alloy (Ni-8 wt% Cr-25 wt% Mo) has been modeled. Features of the model include species transport and AC electromagnetic effects coupled with fluid flow, heat transfer, and solidification. The effect of varying ingot diameter and melt rate, on macrosegregation patterns, local solidification time, and liquid pool profiles obtained from this model are demonstrated. The results show that the macrosegregation in the ingots correlates to the filling velocity.IntroductionElectroslag remelting (ESR) is a secondary melting process used to refine the chemical composition and the microstructure of metals. Macrosegregation of solute elements causes defects in ESR ingots, including freckles and the maldistribution of phases. These defects are not correctable through heat treatment due to the large length scales over which they occur. However, the frequency and distribution of these defects may be minimized, or even prevented, through process control based on an understanding of the conditions that lead to their formation.In the past, studies have been conducted on the effect of the process parameters on the shape of the melt pool and the thickness of the mushy zone [1-7]. In these studies, the shape of the liquid pool is determined by consideration of the heat and fluid flow induced by electromagnetic (Lorentz) force and thermal buoyancy. The transport of solute and the resultant solutal buoyancy effects were not considered in these macroscopic models. Defect formation is tied to formation of secondary phases (e.g., freckling and white spots in nickel superalloys) [5,8]. In cases where secondary phase formation is calculated (e.g., [6]), phase fractions are determined using a micro-scale model given the local solidification time (LST) and local thermal history from the macroscale model.Using the local thermal history from the macroscopic transport model to predict microstructure increases the importance of the accuracy of those results. This investigation models the macrosegregation of molybdenum during the ESR of a Ni-Cr-Mo alloy. The effect of macrosegregation on pool shape and depth is demonstrated, along with its effect on the local solidification time. By comparing the relative effects of the melt rate and ingot radius, a better understanding of the factors that affect macrosegregation, and ultimately secondary phase formation may be obtained."

Jan 1, 2004

By C. Eswaraiah

A drop weight tester (DWT) is designed and fabricated for the purpose of analyzing single particle impact breakage characteristics of different ores. The test results were evaluated through the breakage distributions of different size fractions at five different input energy levels. The breakage parameter, t10 (Narayanan, 1986) is used to represent the degree of size reduction, which is assumed to be representative of the breakage product size distribution obtained from single particle breakage. Representation of breakage distribution with this method consist one more breakage dependent parameter (a). To evaluate the impact breakage characteristic of different ores, a mathematical relationship was established to analyze the dependency of breakage parameters, t10 and a on specific input energy (EIS) or fracture energy (Tavares et al, 1998, Fandrich, 1998), specimen size (?) and Bond?s operating work index (WI0). Mathematical results developed gives adequate model for all ball mill modeling. It can be concluded that the drop weight test method is a useful and practical way of evaluating the impact strengths of various ores and results of which can be used in modeling mills.

Sep 1, 2012

By Sanchita Chakravarty, Sumantra Bhattacharya, Divya Jyoti, A. K. Mukherjee, Soni Jaiswal

"Release analysis is independent of collector and frother dosage and type, but it is primarily influenced by the degree of liberation or “state of release of the sample”. The shape of release curve is an indication of the degree of liberation. This paper briefs about the effect of reagent combination, particle size and surface characteristics on the release analysis of difficult-to-clean LVC coal.Release analysis of three LVC coal fines obtained from two different coalfields of India was carried out at three different size levels such as -0.5mm, (-0.5+0.1) mm, and -0.1mm. The collectors used were n-dodecane and commercial diesel oil. Incomplete liberation of coal fines even at a size of -100µm, corroborated by photomicrographs of ROM and clean coal macerals, in a great measure reduced the flotation-based cleaning potential of the fines. FESEM images of fines reveals that the adherence of ultrafine onto the surface of relatively coarser particles reduced the clean coal recovery. The results obtained also appear to be coal, reagent combination and, particle size and particle surface specific. Only one coal indicated the liberation as is usually expected for -0.1mm particles with a reasonable yield of 65% at 18% ash. INTRODUCTION Froth flotation has a long history of being used to treat coal fines. Coal flotation is considered to be difficult, if the percentage of Near Gravity Material (NGM), i.e. essentially locked particles, in flotation feed is >10% [Aplan, 1993], which is usually the case with all the coking coal fines in India. The fines are rich in vitrinite, so valuable for coking coal. Unfortunately, there appears to be no standard procedures to determine the separation efficiency of froth floatation. Release analysis proposed by C.C. Dell in 1953 [Dell, 1953], aimed to determine the ultimate floatability of coal. Several other techniques had been proposed but release analysis technique has been considered to be a vast improvement over the batch flotation process [Forrest et al. 1994]."

Jan 1, 2018

By Oscar Damiani

El presente texto señala la distribución general de las brechas encontradas en el depósito de Toquepala, especialmente la distribución de la brecha de colapso, a través de ciertas orientaciones. Esta distribución incompatible con el origen diatrémico propuesto anteriormente, sugiere la posibilidad de establecer preliminarmente que el depósito ha sido originado por el fenómeno conocido como «magmatic stopping» emplazado en un área de debilitamiento ocasionado por la intersección de varias fallas pre - existentes, generando de este modo el «breccia pipe».

Sep 1, 1968

By R. E. Moore

The lining systems currently in use in BOF furnaces, certain steel ladles, and the slag line of electric are furnaces were developed during the late seventies through the mid-eighties using a trial and error method of combining aggregate, carbon sources, additives and binders. They are currently based on magnesia, graphite, metal additives and resin binders, the selections of each being tied to the anticipated intensity of the use conditions. The general functions of the respective constituents are well appreciated, however, there is still a great deal that is not known about how the socalled antioxidants protect the graphite nor how impurities from the graphite and the aggregate enter into the wear processes. In a simplified assessment of wear processes, it appears that if the deoxidized layer can be kept very thin, less than 810 mm in depth, and if the viscosity and quantity of the matrix glassy phases can be controlled to resist erosion of the deoxidized layer, lining life can be maximized for the various applications. This paper will discuss the characteristics of the starting materials systems currently being employed for applications requiring a deoxidation function to realize extended wear. It will not attempt to explain all the complex interrelationships between the respective constituents but will point to the potential for improvements through the use of improved constituents.

Jan 1, 1991

By A. R. Udupa

The reduction roasting behavior of chalcopyrite has been investigated using various combinations of a desulfurizing agent, i.e., CaO or Na2CO3, and a reductant, i.e., CO, H2 or C. Using these, combinations the sulfur is removed from the mineral as CaS or Na2S rather than SO2 as is the case with conventional copper smelting and converting. The laboratory reduction ex¬periments were conducted using thermogravimetric analysis (TGA) and boat tests of mixed combinations of fine particulate reactants subjected to a continuous gas stream. The degrees of metallization were determined by both weight loss and chemical analysis methods and the products examined using optical and scanning electron microscopy and electron probe microanalysis. The percent reduction after one hour at 900°C ranged from 60% to 94%. From these data It was possible to provide postulations as to the controlling reduction mechanisms.

Jan 1, 1983

By D. B. Dreisinger, M. R. Tavakoli

Vanadium has been produced from both primary and secondary sources having various compositions. Vanadium pentoxide and vanadium trioxide are the most available and known sources of vanadium oxides. In this paper, an overview of leaching both oxides has been reported. The problem of vanadium pentoxide leaching under acid conditions is the low solubility of the dissolved vanadium. This was investigated and then supplemented with further studies of leaching at mildly basic pH’s as well as under acid reductive leaching conditions (to form vanadium (IV)). Atmospheric oxidative leaching of vanadium trioxide was investigated using oxygen and ferric ion as the oxidant. It was shown that the leaching of vanadium trioxide using oxygen is very slow; however, ferric ion can dramatically increase the kinetics and leach efficiency.

Jan 1, 2014

By CK Tsang, Jack Muir, Dharman Gersch, Joshua Barry

Correct face pressure is critical to safe operation of a closed face TBM. If inadequate face pressure is applied, this will lead to excessive ground movement, and may result in collapse of the tunnel face. Face pressure calculations are performed manually every few meters along the tunnel alignment. With the application of a 3D ground model, ground profile information can be extracted for automatic computation. This will significantly improve the efficiency and accuracy and is adaptable to changes in design parameters. This paper will discuss the development of automatic computation techniques in extracting information from a 3D ground model.

Jun 13, 2021

By Stephen R. Holsinger

During the year of 1972 ASARCO's Silver Bell embarked upon a project that would test a modified grinding circuit using direct digital compute against the performance of its other five grinding lines, implementation and subsequent outcome of that project has been previously reported in a paper by Pitts, et al. The main purpose of the present paper will be to describe major problems incurred during the implementation of this control strategy on the remaining five primary grinding lines and their solutions. Also included will be a discussion of changes made in operating philosophy and methods used since that report was written. Description The Silver Bell concentrator is a 10,436 tonne/day copper sulfide plant supplied by ore from two separate open pits approximately 4 km. apart. As well as receiving ore from these two main pits, ore is received from several exten¬sions of both pits. The ore bodies are variable in rock type and the extensions have increased this variability. Grinding is carried out by six primary, single-stage, 3.20M x 3.66M Allis Chalmers grate discharge ball mills in closed circuit with four Krebs D20B cyclones (Fig. 1). Each of these grinding circuits is controlled by four independent but interactive control elements. These control elements are the fresh ore feed, the water added to the feed end of the mill, the water added to the ball mill discharge sump, and the cyclone feed pump speed. At the present time, instrumentation for measuring primary process variables consists of Merrick weightometers for fresh ore feed, orifice plates coupled with differential pressure transmitters (dp's) for incoming water measurements, back-pressure diaphragm coupled with a dp for estimating ball mill discharge sump level, a magnetic flowmeter for determining cyclone feed velocity and a nuclear density gauge for measuring cyclone feed density. All measuring instruments develop electrical signals that are measured as 2-10 V DC "inputs o the computer interface.

Jan 1, 1977

By B Wu, C Zhao, B Lei

At present, the friction factor is calculated by measuring pressure drop and airway configurations. However, the workload of on-site measurement is heavy, and the measurement results are easily disturbed by the external environment. In order to meet the need of intelligent ventilation to quickly and accurately obtain the friction resistance of roadway. Based on the important of roughness in Atkinson friction resistance formula, in this paper, fractal theory is used to characterise the 3D rough surface, and a method based on fractal dimension to describe the roughness of roadway surface and calculate the friction resistance was proposed. A computational model of friction resistance for fractal characterisation of roadway 3D rough surface was established. The parameters of the model were deduced and verified by using Nikuradse experimental data. The fractal dimension of roadway surface was calculated by 3D laser scanning data of Kailuan roadway, the established friction resistance calculation method was compared with the field resistance measurement results. It is considered that the calculation method of friction resistance based on fractal theory is reliable and can well represent the influence of 3D rough surface characteristics of roadway. The result show that the new established friction resistance formula compared with the traditional Atkinson formula in Nikuradse experimental, the average relative error is 6.874 per cent, and compared with the measured results of ventilation resistance in Kailuan experimental roadway, the relative error is 6.667 per cent. Comprehensive evaluation and analysis suggest that the new formula can well reflect the influence of 3D rough surface on friction resistance, combined with 3D laser scanning technology, the friction resistance of roadway can be calculated quickly and accurately. This research provided a reference for the key technology and theoretical development of intelligent ventilation parameter measurement.

Oct 12, 2022

By S McGregor, J Sharp, I Entezari, T Boulter

The piezocone penetration test (CPTu) is one of the primary screening tools used by the mining industry to evaluate whether tailings are susceptible to liquefaction (static or cyclic). Liquefaction analysis using the CPTu is influenced by the fines content of the soil, and most CPT screening tools empirically use the behaviour type index (Ic) to correct for fines. The issue with this approach is that such empirical relationships have been developed using data collected from natural soils and their applicability to different tailings deposits needs to be studied. In this paper, we explore the use of machine learning to develop a site-specific model to estimate fines content of tailings using gamma piezocone penetration testing (GCPTu) measurements. The results are then compared to the fines content derived from the soil behavior type index (Ic) proposed by Robertson and Wride (1998). A dataset of paired GCPTu and laboratory results were compiled and a support vector machine (SVM) algorithm was employed to calibrate a model to estimate tailings fines content from in-situ GCPTu data. We calibrated GCPTu data to geotechnical 75 μm fines content measured in the laboratory. The geotechnical fines content is the fines content as a percentage of solids. The development dataset was comprised of paired GCPTu-laboratory results collected in 2009-2019 from a mining area with predominately clay mineral and quartz sand tailings. Results show that the developed model predicts the geotechnical 75 μm fines content of the studied deposits with 7.8% error. The Ic based method estimates the fines content with 31% error. Evidently, the Ic method is not applicable to the studied tailings deposits. It is appreciated that many tailings fines do not contain clay, and that the success on this program may not be repeatable everywhere. However, the authors wish to point out that the application of site-specific machine learning algorithms may be used to significantly improve empirical geotechnical parameters.

Jul 1, 2021

By Jahnavi Parmar, Pranav R. T Peddinti, Saloni Pandya, P. S. Prasad

Coastal cities are in desperate need of suitable land to meet the ever-increasing demand for urban infrastructure to support commercial, residential, tourism, and off-shore activities. Countries with a lengthy coastal line, such as India, possess significant areas of wide spread highly saline soils subjected to periodic seawater intrusion. One such soil stratum was encountered at the Gulf of Cambay, Bhavnagar district, Gujarat, India. Due to the high volume of river runoff, the Gulf has a positive water balance. The relative humidity ranges from 65 to 86 percent, making the climate semi-arid to sub-humid. The high salinity, mineral content, basaltic origin, and deeper water table offered the impetus to investigate applicability of various soil treatment options for such saline soils. Admixture stabilization techniques have been shown to help with problematic soil features. The Current study aims to determine effectiveness of addition of locally available lignite fly ash (10% - 30% by weight) and cement (6% - 9% by weight) to Bhavnagar saline soil in respect of strength, electrical conductivity and CBR. In this assessment, a comparison of stabilized and unstabilized saline soil mixtures is expected to highlight the need of understanding influence of treatment on instinctive performance of stabilized saline soils, as well as assist practitioners in efficacious treatment of extreme saline soils for diverse geotechnical and construction applications.

Sep 1, 2022

By R Dwyer

Iron ore currently mined in Australia generally requires very little beneficiation. However, depleting high-grade resources means that in the future low-grade iron ore deposits will need to be mined to meet the increasing demands of the global steel industry. Along with the increased demand, the industry faces additional pressure to reduce the environmental impact of mining and mineral processing. This has stimulated research beyond incremental improvements to conventional processing into alternative low-impact processes, including biotechnological approaches to mineral processing.Bioflotation and bioflocculation have emerged as relatively recent technologies, in which bacteria and/or their extracellular material may be used as flotation reagents (collectors or modifiers), enabling improved selective separation of minerals. The primary advantage is the production of a selective, environmentally-benign alternative to conventional flotation reagents. A biotechnological approach may also be taken in the beneficiation of high-phosphorous iron ores utilising bacteria capable of iron reduction and phosphorous solubilisation.Samples from three iron ore deposits in Western Australia were examined for bacteria suitable for iron ore benefi ciation. A number of common soil microorganisms including Pseudomonas spp, Limnobacter thiooxidans, Paenibacillus spp, and Ralstonia insidiosa were identified using culture-independent molecular techniques. A number of anaerobic species belonging to the genus Clostridium were also identified in the core samples. Selected aerobic species were enriched and isolated on high nutrient media in the presence of haematite. Several of the isolated strains showed an affinity for iron ore, attaching to haematite in enrichment cultures and further demonstrated through adhesion studies. Other isolated species such as Ralstonia isidiosa and Pseudomonas stutzeri are known to solubilise rock phosphates in soils and have potential for the removal of phosphorous from Australian iron ores.

Jul 11, 2011

By Lihong Zhou, DAVOOD BAHRAMI

A reliable and stable ventilation system is essential to the safe operation of underground mines. The stability of a mine ventilation system becomes extremely critical while responding to a fire incident since an unstable ventilation system will pose a risk of airflow reversal. The reversed airflow could bring the fire contaminants such as toxic gases and smoke unexpectedly to working areas. In the past few years, there has been a growing interest in the study of ventilation network stability using the concept of resistance sensitivity, which is described as an indicator of how the airflow in an airway is reacting to a resistance change of other airways. Several methods of calculating the resistance sensitivity in a mine ventilation network have been carried out by researchers and scholars around the world. However, the proposed methods heavily rely on a vast amount of mine ventilation simulations, which are very time consuming and computer-power intensive, especially for a large-scale mine ventilation network. In this paper, a derivative method calculating the resistance sensitivities with a single mine ventilation simulation has been developed and implemented into a mine fire simulation software, MFIRE. The results from the derivative method were verified against the results from a traditional method. The derivative method has been proven to be reliable and accurate.

Jun 7, 2022

By Terence Makanyire, Animesh Jha

The dissolution and chemical properties of vanadium, zirconium, and niobium in rutile lattice are analyzed by comparing the octahedral site preference energies, with respect to Ti4+ ion in the solvent phase. The oxides are often present in rutile lattice and interfere in achieving the quality of pigment grade TiO2 due to favourable Gibbs energy for dissolution in the solvent rutile matrix. Binary mixtures of V2O5 { TiO2; Nb2O5 { TiO2 and ZrO2 { TiO2 with compositions of 80, 85, 90, 95 and 97 wt% TiO2 were made, pelletized and sintered at 1100 °C for 24 hours. The solidsolution mixtures were then cooled and leached in 2M NaOH for 3 hours at 60 °C. Phase and lattice parameter characterizations, and microstructural and compositional analyses were then carried out using X-ray diraction and SEM/EDX, respectively. The leachates were analysed by Atomic Absorption Spectroscopy (AAS), using which the solute dissolution model for oxides were investigated.

Jan 1, 2014

By Matthew John M. Krane, Patrick E. Krane

This study examines the operations of the Cowper stoves attached to an iron blast furnace from a Second Law perspective. The exergetic efficiency of a 3-stove system operating at cyclic steady state is determined using a model accounting for the thermal, mechanical, and chemical flow exergies of the top gas and blast air, as well as the thermal exergy stored and released in the stoves. The analysis covers the heating and mixing of blast gas in one on-blast stove, and the combustion of top gas and its use to heat two on-gas stoves. The effect of different cycle times, and blast furnace operating conditions on the exergetic efficiency of the cycle is examined, and the optimal cycle time for different blast temperatures found. In addition, a study of the combustion parameters quantifies the advantages of using enriched oxygen in the combustors.

Mar 1, 2018

By Y. Zhang, M. Yekich, C. Zhou, C. Jobes, J. Galanko, D. Tuchman, J. Srednicki, J. Carr

The continuous personal dust monitor (CPDM) is an essential instrument for working in hazardous environments, is used to monitor real-time coal dust exposure, and is mandated by the Mine Safety and Health Administration (MSHA) for underground coal mines. Researchers from the National Institute for Occupational Safety and Health (NIOSH) found that it is possible for electromagnetic interference (EMI) between a CPDM and a proximity detection system (PDS) to occur. Various approaches have been taken by researchers and manufacturers to address this EMI issue. Administrative controls were recommended to keep the CPDM six inches away from the wearable PDS device. Shielding pouches were made to contain the electromagnetic (EM) emission from the CPDM. Metal shielding was added to major EM emitting components. EMI filtering with large capacitors was introduced to mitigate EMI. Most recently, a novel magnetic-field-cancellation-based approach was developed and achieved remarkable results. In this paper, we provide a comparison between these approaches. The pros and cons of each approach are presented and discussed, so that mining device manufacturers and operators can best evaluate the technology and controls that improve the health and safety of mine workers.

Feb 1, 2023

By Shamim A. Dar, & Samsuddin Khan, & K. F. Khan, Mohd Shuaib

The Late Paleocene–Middle Eocene phosphate nodules of Solan District of Himachal Pradesh belong to green facies of Subathu Formation of Sirmur group. Field observations indicate sporadic distribution of phosphatic nodules in the yellow brown to rusty brown, buff-colored bleach shales. Phosphatic nodules are dull earthy to dark grayish in color and break with sharp and conchoidal surfaces. Studies of phosphatic nodules using petrological microscope, X-ray diffractometry, and scanning electron microscopy (SEM) attached with energy dispersive X-ray (EDX) reveal that cryptocrystalline apatite (fluorapatite) is the dominant phosphate mineral. Silt sized silica is the dominant gangue, whereas pyrite and muscovite are present as minor gangue. The phosphate minerals occur as oolites, pellets, and cryptocrystalline apatite in the groundmass. Silica veins form a network replacing the original phosphatic matrix. Brown to brownish black color may be attributed by the organic matter in the phosphatic nodules. Completely phosphatized radiolaria and partially pyritized planktonic foraminifera are observed. There is corroboration of organic matter in the form of microbial filaments in the groundmass of apatite. The findings in the present investigation indicate that the different forms of the minerals, their texture, and distribution in the phosphatic nodules might be due to environmental vicissitudes in oxidizing to reducing conditions followed by replacement processes. Presence of microbial filaments may be due to the active role of microorganisms during the formation of these phosphatic nodules.