Search Documents

Longwall mining in Australia is approaching maturity. Longwall production from 'state of the art' Australian longwall mines now rivals similar US based longwall operations. Regrettably however, Australian gate road development rates in general fall short of the required development to longwall production ratios that are required to sustain annual longwall production capabilities. By contrast, most US based longwall mines achieve the required development to longwall production ratios to sustain their longwalls. This is despite many having to drive three heading longwall panel gate headings to meet regulatory requirements.

Jan 1, 1998

By Cyril Wells, Robert F. Mehl

THE practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out 1,13 This importance ties chiefly, though by no means only, in the study of carburizing and in the study of reactions involved in the eutectoid inversion in steel The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in y-Fe and their mutual effects are measured with precision The present paper reports the results of meas¬urements of diffusion coefficients D of manganese in -y-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients [$] Data on the rate of diffusion of manganese in y-Fe have been reported by Fry2 and by Paschke and Hauttmann 3 Claussen4 calculated the diffusion coefficient D from Fry's data as 3 X 10-10 sq cm per sec at 960°, which will be shown to be incorrect by many orders of magnitude Paschke and Hauttmann gave a rough value of 9 6 X 10-8 sq cm per sec at 1400° Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon METHOD AND MATERIALS Method -The method employed is identical with that used earlier 5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded The diffusion anneals were performed in argon, except one (test 18) in which hydrogen was employed for purposes noted below The temperatures reported are accurate to about 3° and constant within I°C , the diffusion times are reported to the nearest half hour The specimens were furnace-cooled after the diffusion anneal at about 2° per min Layers, usually 0 004 in thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0 01 per cent Mn, the distances of these layers from the interface was measured to ±0 0002 in The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions e The D values calculated by these two methods do not differ appreciably 5 The Grube solution was used except in tests in which the effect of concentration upon D was greater than 50 per cent, in such cases the Matano method, which explicitly provides for the variation of D with concentration,1 is the more reliable In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer In 3 of the 30 tests, however, this is not justified, and the D values

Jan 1, 1941

By H. C. Goodrich

At the Utah Copper mine, steam shovels were first used, in 1906, for the removal of overburden, and in June, 1907, for the mining of ore. Prior to 1907, the ore came from underground development work and from stoping. The use of the steam shovel gradually increased until 1914; since then all material, both overburden and ore, has been loaded by power shovels operating on the various benches of the mine. During these 19 years, there has been a great improvement in open-pit mining, largely in the use of equipment having greater capacity and dependability. The history of the development of mechanical shovels and related equipment, as affecting the Utah Copper Co., would be interesting and would justify considerable space; but of greater interest at this time is the operation of the equipment now in use. The Utah Copper mine is in a great deposit of copper-bearing monzo-nite, which occurs as a prominent headland of the Oquirrh range of

Jan 1, 1925

By D. W. Evans

Mine subsidence problems due to coal extraction have occurred in a number of areas throughout the United States. Depending on the local geology, the depth of the mined seam, the type of mining method employed for extraction, and other related factors, subsidence can result in anywhere from slight displacements to a total loss of ground. These conditions can have serious consequences on the health and safety of the people living above the mined areas. A number of methods exist to provide support for the ground overlying mines. All of these methods employ some mechanism for providing additional support to either the roof of the mine or the sides of the pillars. Since failure usually occurs due to overburden stresses which are transmitted to the roof and pillars, these methods employ techniques to counteract stresses induced due to the coal extraction. The applicability of any particular method will depend on the availability of backfill material, the areal extent of the affected area, and of course, the cost. The primary use of coal ash for subsidence control has been as a backfill material for the stabilization of large areas. Large scale backfilling projects for subsidence control have been performed in Rock Springs, Wyoming, Wilkes-Barre and Scranton, Pennsylvania, and in Fairmont, West Virginia. Some of these projects have utilized sand, as well as, coal ash as backfill material. Much of the backfilling work performed in the United States has been done in an effort to control mine subsidence in abandoned mines. South Africa, on the other hand, has used backfilling extensively both for ash disposal and to increase extraction in active mines. The utilization of repetitive fill and mine techniques has resulted in extraction increases of as much as eight percent in shallow mines and as much as twelve percent in deep mines.(1) The coal ash injection system which can be used for backfilling depends largely upon whether the mine voids are dry or submerged. For dry mines, hydraulic or pneumatic conveyance systems can be used, while submerged mines are limited to backfilling by hydraulic methods. The use of coal ash as a backfill material has a number of advantages, such as: 1. Coal ash is available in areas throughout the United States and in many instances is conveniently located near areas requiring backfilling. 2. Coal ash is available in significant quantities since many coals when burned will result in about 15 to 30 percent ash by weight. 3. Coal ash as backfill is, in many instances, the most economical alternative fill material. Due to the costs associated with above ground disposal, power companies will often times give the material away to lower their overall operating expenses. 4. Coal ash is usually pozzolanic in nature, that is, this material results in cementitious bonding within the backfilled matrix of material.

Jan 1, 1982

By Jun-Yan Chen, Stefan H. Boshkov

Metal mining in the People's Republic of China has shown great growth during the last three decades. Over 150 new iron ore mines and nonferrous base metal mines have been opened since 1949, althouc.11 most of them of medium and small size. Concurrently, many old mines were enlarged and reconstructed. The production of iron ore has grown from less than 1.5 million tons per year in 1949 to almost 76 million tons in 1978. A corresponding increase in the total annual output in the nonferrous metal mineral industry has also been noted. It is well known that the PRC is very rich in metal mineral resources. The reserves of tungsten, tin, antimony, molybdenum and iron ore are ranked in the top three in the world. Recently, some copper porphyry ore deposits were discovered in Jianxi and Anhui provinces. Some large nickel-copper sulfide deposits were discovered and have been developed in North- West China. Huge iron ore deposits have been found in Liaoning, Hebei and Szechwan provinces. However, the bulk of the iron ores are low grade. The growing metal mineral production has met basic domestic needs since 1949; it has also proven China's big resource potential. Mining methods have also undergone development in the past 30 years. About 80% of the annual output of iron ore comes from open pits, whereas about 58% of nonferrous metal ores come from underground mines. Blasthole open stoping, sublevel caving and induced block caving are widely used in Chinese underground metal mines (table 1). This paper summarizes in detail the planning for and application of these three bulk mining methods in the nonferrous and iron ore mines in China. CLASSIFICATION OF UNDERGROUND MINING METHODS The main principle of the classification of underground mining methods in PRC is ground support in the stoping cycles of the mining blocks or stopes. Table 2 lists this classification. It is essentially the same as that given in the SME Mining Engineering Handbook. Be- cause pillar removal is a secondary mining operation, using a variety of methods, they are not included in this classification. As is the case with most classifications in science and technology, there is no precise division between the classes of mining methods. Because of the rapid development of consolidated filling techniques in the past twenty years, some types of open stoping methods use fill in order to improve the ground conditions for the secondary recovery stage. Thus, these mining methods have features of both methods using no artificial support and those using artificial support. In this classification, this type of mining method is placed in the latter category. The shrinkage stoping method has been employed extensively to mine steeply dipping narrow veins of tungsten and tin in the Jiangxi, Hunan, Guangdong and Guangxi provinces. Shrink- age stoping is placed under the class of mining methods without artificial support be- cause this reflects the nature of the Chinese experience. The function of the broken ore serving to support the footwall and/or hanging wall is limited, because the expectation is for the host rocks to remain unsupported until the stope is drawn empty. APPLICATION OF BULK MINING METHODS Bulk mining methods consist of blasthole open stoping, sublevel caving and block caving. These stoping methods have much in common, such as: bulk ore materials blasted by long holes; higher production rates of stopes or blocks and higher production efficiencies of the whole mining systems.

Jan 1, 1981

By Scott G. Britton

Today's coal mines are turning more and more to belt haulage as the key system to transport coal out of the mine. The advantages of using belt for both intermediate and main haulage are numerous. Belts are reliable high capacity haulage mediums that can be utilized at low operating costs. They are adaptable to rolls in the coal seam and can handle relatively steep grades. They are not noisy, operate with a minimum amount of labor, and are easily extended and retracted. Belts require the least power of any haulage medium, are easily controlled by push- buttons and interlocks, and present low fire and safety hazards. Belt haulage can also be the largest source of operational problems for mine management when not installed correctly. This chapter and Chap. 6 concentrate on proper installation of both the static and dynamic components of efficient belt haulage. This chapter looks at the static system component, composed of the belt drive, its installation and operation, as well as belt takeup and transfer point construction. These components do not change readily over the life of the installation, hence the term static system. Chap. 6 discusses the dynamic system of belt line construction, which includes belt splicing, breaking down and reanchoring the tailpiece, and extending the belt line, plus operational and maintenance items for belt operation. This chapter is divided into three major topics. The first is a general discussion covering the points necessary for designing an efficient haulage system; the second looks at installing belt drives, head rollers, and takeups, and the third discussion centers on installing efficient and effective transfer points along the haulage system. Each will address the design and construction issues facing the engineer or construction supervisor in charge of installing the system. Before looking at the static system, it may be useful to review some of the basic design factors and considerations of all belt haulage systems. The material usually carried on an underground belt is a mixture of raw coal and rock, commonly known as run-of-mine (ROM) coal. This mixture has certain material characteristics that guide the mining engineer to the final and proper belt selection. The characteristics looked at most frequently are: 1) Angle of Repose is the angle at which the material will freely make a pile. Most ROM coal averages a 35"-39" angle of repose. 2) Angle of Surcharge is the angle a pile will assume on a moving conveyor. This ranges from 5" to 15" less than the angle of repose in most materials. For ROM coals, 25" is the average angle of surcharge. 3) Flowability, which determines the maxi- mum cross-sectional area needed to carry any given material on a belt. It is measured by the angles of repose and surcharge of a material and also serves as an index of the safe incline angle for the belt line. These characteristics, plus practical engineering research and development work are defined by an organization called the Conveyor Equipment Manufacturers Association (CEMA) for most bulk materials. CEMA also provides a code for each classified material depending on the characteristics above and the subjective considerations of the average size to be encountered, the abrasiveness of the material, and any miscellaneous characteristics (oil resistive, corrosive, etc.) which may be important. For coal, CEMA (composed of member companies in-

Jan 1, 1983

By P. Raffinot, C. H. G. Bushell, S. Hodgson, E. F. Milner, H. J. Bosshardt, N. Draper, D. E. Pickett, Edwin T. McKnight, J. Prieto

Zinc ranks third and lead fourth in world nonferrous metal conumption. In 1972 the free world consumed 3,333,000 mt of refined lead and 4,422,000 mt of refined zinc. The lead tonnage was divided into the following end uses: storage batteries (42%), lead allows (7%), pigments and chemicals (11%), cable sheathing (9%), gasoline additives (13%), pipes and sheets (8%), and miscellaneous uses (10%). The corresponding distribution of zinc uses in 1972 was galvanizing (39%), die casting (26%), brass (15%), rolled zinc (8%), oxide excluding American Process zinc made directly from concentrate (6%), and other uses (6%). The pattern of usage of lead and zinc varies considerably from country to country. During 1972 in the USA 49% of refined lead was consumed in storage batteries, 19% in gasoline additives, and only 3% in cable sheathing, whereas in the United Kingdom 28% of the lead was consumed in batteries, 14% in cable sheathing, and 14% in gasoline additives. For zinc the major US uses were die casting (41%) and galvanizing (37%), with about 3% consumed as rolled zinc; corresponding usages in the same applications in France were 12, 28 and 28% and in Australia 12, 67, and 3%, respectively. The outstanding resistance of lead to corrosion, its density, and

Jan 1, 1985

By R. E. Ogilvie, J. I. Goldstein

The a and y solubility limits in the Fe-Ni phase diagram have been redetermined at temperatures above 500°C. Both a diffusion-couple and a quench and anneal technique were used. The solubility limits were measured with an electron-probe micro-analyzer. The nickel concentration at the phase boundary is increased below 700°C and the a solid-solubility range is much larger than had been previously measured. The solubility limits are also extrapolated to 300°C. It is suggested that the solubility of nickel in a FeNi reaches a maximum in the temperature interval 400o to 500°C. THE equilibrium diagram has been of great use in the field of meteoritics, where the phase relations between kamacite (a) and taenite (?) in metallic meteorites can be described by means of the Fe-Ni diagram. The study of metallic meteorites by electron-probe microanalysis has cast some doubt on the accuracy of the presently available Fe-Ni diagrams.1, 2 Recent thermodynamic studies of the Fe-Ni system also suggest that the diagram may be in error.3 For these reasons the high-temperature (800o to 500°C) part of the diagram was redetermined. INTRODUCTION The currently accepted Fe-Ni diagram is that of Owen and Liu.4 Above 910°C, there is a region of complete solid solubility, ? (fee). Below 910°C, the a (bee) phase is stable in pure iron. The effect of increasing amounts of nickel is to stabilize the y phase. The phases that form when Fe-Ni alloys are heated or cooled bear little relation to the equilibrium diagram. If an alloy is cooled from the y state and held at a temperature within the a + y field, no evidence has been found for the occurrence of the y - a transformation.5 If the alloy is cooled to low enough temperatures the y phase breaks down into a supersaturated bee phase called a2. In fact, in alloys over 27 pet Ni the y phase is retained at room temperature.6 The a, phase has the same composition as the original y. The temperature at which a2 forms, the M, temperature, has been determined experimentally.' A state of equilibrium can be approached by cooling below M, to form a2 and then reheating the alloy into the two-phase region of the diagram. The y phase will then begin to precipitate out of the a2 phase and grow. The growth of the phase, however, is quite slow. Using the interdiffusion coefficients -Da of Goldstein et al.,8 it is estimated that it takes about 1 year to grow a 10-µ-wide region of ? at 700°C in a 5 pet Ni alloy. Owen and Liu4 used the technique just described to form the equilibrium phases. The phases present were determined by means of X-ray analysis. The accuracy of their diagram depends on the number of alloys available near the phase boundary at a given temperature. In this study two different techniques were used to determine the a/a + ? and ?/a + ? solubility limits. The inherent accuracy of both techniques was greatly improved over that used by previous investigators because the phase-boundary compositions were measured with an electron-probe microanalyzer. PROCEDURE The two methods used to determine the Fe-Ni diagram are the diffusion couple (D.C.) and the quench-and-anneal (Q.+A.) techniques. In the first method, diffusion couples whose diffusion path goes through a two-phase region of the phase diagram were used. A description of the technique used for making the diffusion couples has been described in a previous paper.' After the diffusion treatment a discontinuity in the resultant concentration vs distance profile was measured. The nickel concentrations in the a and ? phases at the interface of the discontinuity are the solubility limits of the a and ? phases in the phase diagram at the diffusion temperature. If the interface com-

Jan 1, 1965

By Robert E. Green

Formulae are given for calculating the modes of wave propagation in a single-crystdl specimen possessing a given crystallographic orientation. Such calculations lead to determination of the orientation factor appearing in the Granato-Lucke theory for the attenuation of these waves due to dislocation damping. A detailed treatment is given for the case of an aluminum crystal possessing the orientation having a maximum Schmid fac -tor of 0.5. FOR a number of years the attenuation of ultrasonic waves propagating in metals has been used to investigate various phenomena causing internal friction.Most of the experiments were performed on polycrystalline test specimens and the waves were assumed to be propagating in an isotopic medium. However Alers 6 in 1955 and more recently Hikata et at. Chiao and Gordon,8 and Swanson and Green 10 have used measurements of attenuation of ultrasonic waves to study internal-friction changes in single crystals. These authors were concerned with the energy losses experienced by the ultrasonic waves due to dislocation motion induced by plastic deformation of the crystals. Alers measured the attenuation of 7 mc per sec ultrasonic pulses propagating in zinc single crystals before, during, and after plastic deformation. Simultaneously he measured the time-dependent plastic strain at constant stress in order to study the correlation between this strain and attenuation. The crystals were oriented in such a way that the applied stress provided a direct shear on the slip plane, thus causing the deformation to proceed by slip on this plane. At the same time the high-frequency sound pulses were sent through the crystal perpendicular to the slip plane. He found that the attenuation of transverse waves, the stress vectors of which lie in the slip plane, was very sensitive to the deformation. The polarization of the particle displacements, associated with these waves, relative to the applied static shear stress, and hence the direction of slip, had no obvious effect on the results. The attenuation of longitudinal waves was affected by the deformation only when the slip plane was not perpendicular to the propagation direction. This indicated that the attenuation was caused by dislocations introduced by the deformation and moving only in the slip plane. Hikata et al. made simultaneous measurements of attenuation, velocity changes, and stress-strain relations on aluminum single crystals deformed in tension. Both longitudinal and shear waves were used, at frequencies of 10 and 13 mc per sec. They placed emphasis on the choice of propagation modes and polarization of the ultrasonic waves, such that interactions between these waves and dislocations on selected slip systems could be investigated. They also selected specimens possessing specific crys-tallographic orientations, which allowed investigation as a function of the number of equally favored slip systems under the applied stress. They found that, for symmetrical orientations, the change of attenuation decreases with the increasing number of equally favored slip systems, i.e., in the order

Jan 1, 1964

By E. M. Wise, T. E. Kihlgren, N. B. Pilling

Systematic data are presented on the relation of composition of nickel silvers to color, tarnish resistance, hardness and liquidus temperatures, for alloys containing up to 30 per cent nickel and 50 per cent zinc, further modified at certain nickel and zinc contents by 0 to 8 per cent of tin and 0 to 10 per cent of lead. Attention has also been directed, using a still more limited range of alloys, toward a study of tensile properties and such casting properties and characteristics as fluidity, shrinkage and pressure tightness. In some of these, rather broad ranges of composition are dealt with; in others, it has been expedient to focus attention on the Federal Specification 20 per cent nickel silver casting alloy, WWP-541. Introduction The demand for an alloy essentially white in color, which could be cast and worked by simple methods and which possessed strength and corrosion-resisting properties superior to the usual brasses, led to the discovery and early use of cupronickel alloys containing zinc, and sometimes tin, lead and other metals. This type of alloy was generally known as 'German silver until the war, when the term "Nickel Silver" became generally accepted. The element principally responsible for the white color of the alloy and for its strength and corrosion resistance is nickel, which may constitute from 8 to 30 per cent of the alloy. The functions of the other elements will be described later. The manifold uses of nickel silver are largely due to its color, corrosion resistance, ease of casting, fabrication, joining and rather moderate cost. In many instances the alloy is finished by grinding and polishing while in others it may be finished with a silver or nickel plus chromium plate. Electroplates applied to a nickel silver base behave more satisfactorily than those applied to the softer and less resistant alloys, and owing to the white color of the underlying metal the article will retain a pleasing appearance despite local failures of the plating.

Jan 1, 1935

By G. W. P. Rengstorff, L. E. Olds

High purity molybdenum ingots containing controlled amounts of a single impurity element (oxygen, nitrogen, or carbon) were prepared. These ingots were tested for ductility by bending test specimens at various temperatures. The relationship between the plastic behavior of the ingots and their chemical composition has been determined. MANY proposed applications for molybdenum require ductility at or near room temperature. At the present time, it is possible to obtain wrought molybdenum with considerable ductility only if special fabrication techniques are used to control the grain structure. Starting with are-cast or powder metallurgy ingots, the usual methods for obtaining ductility rely on fabrication procedures that result in fibered microstructures in the finished product. Recently, it has been found that the ductility of either powder metallurgy or are-cast molybdenum can be improved by uniform recrystallization of the metal to a very fine equiaxed grain structure.' The need for a fibered or a fine grained structure may limit the practical usefulness of molybdenum. For example, welding. which may be used in fabricating the metal, generally produces coarse grained structures that lead to brittleness. This applies, certainly, to currently available commercial molybdenum. Although commercial molybdenum is brittle when the grains are coarse, it has been shown experimentally that fine grained structures are not always essential for ductility. For instance, as-cast molybdenum with a coarse columnar grain structure is ductile if it is sufficiently pure.' Because high purity cast molybdenum has good ductility even when coarse grained, it is probable that the brittleness in coarse grained commercial molybdenum is caused by the impurity content of the metal. Although the general effects of impurities on the cold ductility of molybdenum have been known in a qualitative manner for some time, no quantitative evaluation of these effects has been available. The present investigation was made in order to determine more accurately the effects of oxygen, nitrogen, and carbon on the cold ductility of cast molybdenum. Oxygen has long been known to be detrimental to ductility, although the minimum amount which will embrittle molybdenum has been open to speculation. Parke and Ham" showed that ingots with oxygen contents above 0.003 pct could not be forged. Maringer and Schwope have described the embrittle-ment of molybdenum wire by oxygen. A discussion on the effects of heat treatment on the distribution of oxygen in molybdenum has been given by Perry, Spacil, and Wulff." Although nitrogen would also be expected to have harmful effects on ductility, no extensive work has been done previously to determine whether this is so. However, Tury and Krausz" found that wires presumably with less than 0.007 pct N were brittle. Carbon is added to commercial cast molybdenum for deoxidation. Parke and Ham" have shown that molybdenum containing as much as 0.06 pct C could be forged if the oxygen was kept below 0.003 pct. Also, Bruckart and others' found that the room temperature ductility of sintered molybdenum improved with carbon contents up to 0.84 pct. However, Rengstorff and Fischer' found that residual carbide particles in cast molybdenum apparently had an unfavorable effect on room temperature ductility.

Jan 1, 1957

By A. E. Powers

YEARS of experience and research have shown that molybdenum, tungsten, and vanadium are among the most useful and effective elements in augmenting the high-temperature strength of heat-treatable, ferritic steels. Grün, for example, in conducting an early survey of the strengthening effects of various elements in annealed, low-carbon steel at 750° and 930°F (400° and 500°C), found molybdenum and vanadium to be the most effective.' Holtmann comprehensively studied the strengthening effects of molybdenum and vanadium in quenched and tempered steels at 930°F as a function of microstructure and carbon content.' He found creep strength to be related to the saturation of the austenite at the austenitizing temperature, such that strength is increased by alloying until the y loop is reached—the terminus of complete austenitization. Beyond this degree of alloying, the inability to heat treat will result in lower strength, at least for low and moderate creep temperatures. Tungsten, owing to higher cost than molybdenum, has been little used in ferritic high-temperature steels. As a result, very few investigations have been made of its high-temperature strengthening ability, and reliable data on its effectiveness are not available. Grün rated tungsten far less effective than molybdenum at 930°F (500°C) on a weight-percentage basis.' However, Tammann has found that tungsten is as effective as molybdenum in raising the recrystallization temperature of iron. For this reason Smith, in a review of the subject, has advocated a re-examination of the influence of tungsten on the high-temperature strength of steel.' In any study of the effects of alloying additions on high-temperature properties, recognition must be made of the many variables involved, some of which can be controlled but have been ignored in innumerable investigations of the past, and some of which are difficult or even impossible to control. One cannot, for example, assign a definite strengthening index to any one alloying element, for this will be dependent upon the microstructure (heat treatment and mechanical treatment), testing con- ditions (temperature, time, and stress), and the complete composition of the steel (accompanying alloying elements, impurities, etc.). One ever-appear ing variable, hardness or tensile strength at room temperature, may be eliminated by heat treating all of the alloys to a single hardness level. An attempt may be made to control the variable of primary quenched structure by oil or water quenching the test specimen. The control of such variables may not be possible in cases of widely varying compositions, but at least such deviations should be recognized. Material and Procedure The alloys, made as 30-lb ingots in an induction furnace, all had the same base composition of about 0.18 pct C, 0.85 pct Mn, and 0.48 pct Si. They were grouped as follows: Mo Group—Containing up to 5.2 pct Mo. W Group-Containing up to 6.0 pct W. V Group—Containing up to 3.3 pct V. Mo-V Group—Containing up to 2.7 pct Mo and up to 1.4 pct V. Mo-W Group—Containing up to 2.5 pct Mo and up to 2.5 pct W. The steels, listed in Table I, were forged to ¾ in. sq bars and the material for the high-temperature, rupture-test specimens was further swaged to %-in. round bars.

Jan 1, 1957

By W. B. Nelligam, J. Tittman

Refinements in radiation logging techniques during recent years have involved increasing usage of scintillation ditectors. These detectors produce voltage pulses whose heights are related to the energies of the gamma rays which initiate them. Analysis of the gamma-ray spectrum, as indicated by the pulse heights, yields information about the chemical elements composing the formations surveyed. Refined scintillation counter techniques can furnish chemical information concerning earth formations in situ, from a study of the gamma-ray spectra emitted by the formation either naturally or as a result of neutron bombardment."' Accompanying the rising interest in gamma-ray scintillation spectroscopy, there has been increased activity in the development of accelerator-type neutron sources (in contrast to encapsulated chemical-mixture sources). Such neutron generators are attractive for several reasons: (1) they greatly reduce radiation hazards to personnel; (2) there is a great reduction in contamination danger if they are lost in the hole; (3) they can produce larger neutron intensities than can conveniently available encapsulated sources; and (4) they are capable of being pulsed, thus permitting new techniques in logging. In the past, both accelerator and encapsulated neutron sources have been used by others in conjunction with scintillation-detector pulse-height analysis. The results have not been too encouraging, due to the interference among different gamma-ray spectral lines and to the fact that the gamma-ray peaks were not too clearly distinguishable above the large and ill-defined background "noise".'.' This paper is a status report on laboratory studies of a technique using a borehole accelerator as a neutron source, which gives an improved scintillation spectrum, thus permitting more accurate chemical analyses of the formations penetrated. The Schlumberger-accelerator neutron source' is presented; the origins of inelastic and of thermal-neutron, capture gamma rays are dis- cussed, and results are given for some laboratory measurements performed in borehole geometry. THE NEUTRON GENERATOR-TUBE ACCELERATOR In the attempt to develop an accelerator neutron source which would have the desirable properties outlined in the "Introduction" and which would operate satisfactorily under borehole logging conditions, a small-diameter, cylindrical, neutron generator tube has been developed. This tube utilizes the principle of accelerating deuterons (heavy hydrogen nuclei) by a high voltage so that they bombard a tritium (heavy, heavy hydrogen) target. The resulting reactions produce large numbers of neutrons of 14 Mev energy. Furthermore, the tube is permanently sealed and, thus, the use of pumping techniques in the sonde is avoided. The tube consists of a pressure control, an ion source in which the deuterons are stripped of their electrons, an accelerating gap down which the deuterons are sped by the high voltage, a secondary electron suppressor and a tritium-loaded target. Obviously, the tube requires auxiliary circuitry in a sonde for the control of the ion source, tube pressure, high voltage and other operating variables. Neutron yields, both continuous and pulsed, have been produced under simulated field conditions in the range between 1 and 10 times those conventionally used in neutron logging applications. For the experiments discussed in this paper, neutron-pulse repetition rates in the range between 500 and 5,000 pulses/sec are adequate. Furthermore, by making suitable adjustments in operating conditions, one can vary the pulse width from a minimum of several microseconds up to dc. As will be seen later, the present application to well logging does not require that one have available pulses of neutrons which are appreciably shorter than the time it takes for fast neutrons to slow down to thermal energy in water. As a consequence, much of our interest has been directed towards the operating characteristics of the tube with pulses longer than about 10 microseconds in duration. Our experience to date shows that tubes can be operated in this manner with reasonably constant, average neutron outputs.

By David R. Mitchell

THIS paper is limited primarily to a description of dry coal-cleaning processes in which air currents are used to effectuate a separation between coal and refuse. Processes depending mainly on differences in the coefficient of friction, resilience and shape are not described unless the use of air is necessary for the proper functioning of the process. The air cleaning of coal is of primary importance to the coal industry of the United States. From figures presented in the 1941 edition Mechannual,1 it is estimated that at least 12 million tons of bituminous coal was cleaned in the United States during 1940 by machines using air as the separating medium. One of the current problems confronting the coal-preparation engineer is the dry cleaning of small sizes and slacks. Progress in machine development for the cleaning of small sizes has been slow in recent years in the United States of America; it has been much more rapid in Britain and on the European continent. This paper does not attempt an exhaustive survey of all these developments, and only machines and processes that have found considerable commercial application are cited. Further, no critical analysis has been made of the theory involved in the separation of coal from refuse by processes using air as the separating medium other than that necessary for an understanding of particular machine designs and applications. HISTORICAL SUMMARY The possibility of using air for the separation of coal from refuse was recognized early by mining men and many attempts were made to develop commercial machines. The ingenuity of the early experimenters is to be marveled at in view of their lack of knowledge of the theoretical principles involved. As in other arts, practice has largely preceded theory. Yet, science and practice play a game of leap frog, now one ahead, then the other; the careful experimenter governs his efforts along practical lines by adapting his experiments to the limits prescribed by scientific laws. By first studying developments and the theory involved, it is not only possible to adapt processes to new uses but also to reduce materially operating cost and to build larger units without costly failures. Although many inventors have applied for patents for separating minerals by the use of air currents, the literature in regard to coal is meager. Berrisford2 describes briefly some of the early attempts to clean coal without the use of water. Several of the examples cited by him are reproduced herein. Fig. I shows a machine used for grinding and sizing, in which rollers running in a pan with a perforated bottom and fan opening on the side crushed the coal, which was then carried by the air currents to a settling chamber. The heaviest particles dropped out first and the light ones farthest away, as shown. In the year 1864, a machine was made that could be used as a sizer or to separate dirt from coal with a sized feed (Fig. 2).

Jan 1, 1942

By R. N. Thurston, E. A. Nesbitt, G. Y. Chin

A general relalionship between the amount of glide shear (due to slip) and the macroscopic shape change has been developed. Since the deformation can be large, finite strain analysis is employed. In this treatnzent, the shape change is expressed by a deformation gradient matrix, F - [axi/aXj1, where X and x refer to the initial and final positions of a particle. This matrix is readily evaluated in terms of the amounl of glide shear, a , and the direction cosines of the slip-plane normal and the slip direction for a single active slip system. In the case of deformation from slip on several systems, the product F(a) of the several deformation gradient matrices is first calculated. Then, by assuming that the final configuration is reached by a long series of small shears of magnitude a, occurring more or less alternately in the several slip sys- IN problems of crystal plasticity, it is often necessary to relate the amount of glide in the operating slip systems to the macroscopic strain components. This relationship is relatively simple when only small strains are considered. In this case the separate strain contributions from several slip systems are additive. Such a procedure is incorrect in the case of large plastic deformation. To the authors' knowledge, no general treatment of the latter problem has appeared in the literature. In specific instances, Mark, Polanyi, and schmid3 have derived the relationship between glide and axial elongation during tensile pulling of a single crystal when only one slip system is active. A similar relationship for duplex slip was worked out by v. Goler and Sachs.4 Taylor and Elam5 have also studied in detail problems of large plastic deformation. Due to uncertainties as to the slip systems at the time, terns, the final deformation gradient matrix can be obtained. Mathematically, the problem is reduced to finding the limit of F(dN as N — m while a — 0 in such a way that the Product Na = 0, a ftnite conslant designatzng the accunzulated amount of shear. It turns out that this limit is simply , where F, is the matrix whose elements are the coefficients of a in the F(a) matix. Application is made of the present treatment to a fcc crystal of Perlrzalloy compressed on the (110) plane and contrained to elongate zn the [112] directzon. In addition, it is shown that one rnay readily obtain from the general analyszs the well-known formulas relating elongation, amount of glide shear, and amount of lattice rotation for crystals deforming by single and double slip under tension. however, they were mainly concerned with proving that slip occurs on {111}(110) systems in fcc metals. The present general treatment arose out of recent investigations of magnetic anisotropy in cold-worked Fe-Ni alloys6 as well as some related problems in strength anisotropy of single crystals.' Detailed application of the general analysis will be provided in the case of a Permalloy single crystal compressed on the (110) plane and constrained to elongate only in the [112] direction. It will be seen that, as expected, the small strain approximation leads to significant errors after moderate straining. It will also be shown that the present general treatment yields the formulas of Mark et al. and of v. Goler and Sachs in those specific cases. GENERAL CONSIDERATIONS Consider a homogeneous deformation in which a material point initially at moves to both positions being referred to the same set of Cartesian axes. Such a deformation can be

Jan 1, 1967

By Thomas Egleston

DURING the year 1873, my attention was called to the frequent accidents, resulting from the breaking of rails, on the different railroads in this' country, and I was requested to investigate the subject. The plan of investigation I proposed was to ascertain, in as many cases as possible, the exact hist* of broken rails, both in this country and in Europe; to collect information in Europe relating to the tests which rails used there were required to undergo, and to experiment upon the pieces of rails broken on the road, with a view to ascertain whether their fracture was due to their chemical constitution, bad manufacture, to a reduction in strength owing to temperature, or to physical changes in the constitution of the rail. The investigation was commenced by the collection of statistics, and for this purpose I spent several months in Europe, collecting information on the subject of broken rails, as well as the life of iron and steel rails generally, and inquiring into the systems of purchasing and of testing them employed by the railroads there, intending, on my return, to make a series of analyses of rails broken, both in this country and in Europe; to ascertain, if possible, how far great cold had an influence on the fracture; to examine whether the rail broken, either on the road or afterwards, underwent, at or about the fracture, any physical change, and to make a series of experiments on the strength of rails manufactured in the United States or sold in the American market. Unfortunately, the panic of 1873 came on, just before my return from Europe, and prevented the carrying out of the larger part of the plan proposed; as, however, I had collected in the meantime, a large number of statistics of different kinds from all parts of Europe, and had made a number of interesting experiments and investigations, I have thought it would be worth while to communicate some

By T. Egleston

DURING the year 1873, my attention was called to the frequent accidents, resulting from the breaking of rails, on the different railroads in this country, and I was requested to investigate the subject. The plan of investigation I proposed was to ascertain, in as many cases as possible, the exact history of broken rails, both in this country and in Europe; to collect information in Europe relating to the tests which rails used there were required to undergo, and to experiment upon the pieces of rails broken on the road, with a view to ascertain whether their fracture was due to their chemical constitution, bad manufacture, to a reduction in strength owing to temperature, or to physical changes in the constitution of the rail. The investigation was commenced by the collection of statistics, and for this purpose I spent several months in Europe, collecting information on the subject of broken rails, as well as the life of iron and steel rails generally, and inquiring into the systems of purchasing and of testing them employed by the railroads there, intending, on my return, to make a series of analyses of rails broken, both in this country and in Europe; to ascertain, if possible, how far great cold had an influence on the fracture ; to examine whether the rail broken, either on the road or afterwards, underwent, at or about the fracture, any physical change, and to make a series of experiments on the strength of rails manufactured in the United States or sold in the American market. Unfortunately, the panic of 1873 came on, just before my return from Europe, and prevented the carrying out of the larger part of the plan proposed ; as, however, I had collected in the meantime, a large number of statistics of different kinds from all parts of Europe, and had made a number of interesting experiments and investigations, I have thought it would be worth while to communicate some

Jan 1, 1875

By H. J. Snyder

Both the room-temperature and 600°F (315°C) primary solid-solution phase boundaries for the silver comer of the Ag-Cd-In temary system have been determined using X-ray diffraction and metallo-graphic techniques. Solid solubility of indium in silver at room temperature and 600°F (315°C) is shown to be between 20.3 and 21.7 wt pct, and corrects the previously extrapolated value of 18 wt pct appearing in the literature. The solid solubility of cadmium in silver at room temperature, not previously established, is shown to be between 34.9 and 41.3 wt pct. The solid solubility of cadmium in silver at 600°F (315°C) is confirmed as 43.2 wt pct. The shape of the primary phase boundary line for the subject temary system appears straight at room temperature and curves con-vexly towards the solvent (silver) comer at 600°F (315°C). THIS investigation was undertaken to initiate development of the Ag-Cd-In ternary diagram by establishing the primary solid-solution phase boundary in the silver corner of the diagram. At the present time, a diagram for this ternary system is not available, while this system appears to offer potential for a variety of uses. One alloy in the system has already proven to be useful as a control rod material in nuclear reactors.1"3 To encourage additional exploration of the potential of the system an understanding of its ternary diagram would be beneficial. It is towards this end that the present study is directed. LITERATURE SURVEY In undertaking this study, a comprehensive literature survey was first conducted to find information that would be useful for guidance. Useful knowledge did result from investigating the respective solubilities of indium and cadmium in silver as indicated in the binary constitutional diagrams of the systems Ag-In and Ag-Cd and also reviewing possible shapes of ternary primary phase boundaries. Weibke and Eggers~ used metallographic techniques to establish the system In-Ag as illustrated in Fig. Is This diagram shows that silver in the solid state is capable of dissolving approximately 18 wt pct In. This solid solubility of indium in silver holds true from room temperature up to 1276°F (691°C), then decreases continuously up to 1'761°F (960.5"C), the melting point of the silver. The solid-solubility limit of indium in silver established by Weibke and Eggers has been confirmed by Hume-Rothery and Reyno1ds. G Durrant' used a method which consisted of microscopic examination of quenched specimens to establish the Cd-Ag system as displayed in Fig. 2.' The primary phase boundary of Fig. 2 proved to be in good agreement (ie., within 1 wt pct) with other studies*'1' of the Ag-Cd system made using X-rays and metallog-

Jan 1, 1968

By Alexandra Amiel

Tarkwa Gold Mine is owned by Gold Fields Ghana, IAMGOLD and the Government of the Republic of Ghana in a 71%, 19% and 10% ratio. The mine is operated by Gold Fields Ghana. This large, low-grade, open pit, gold mining operation is located in Tarkwa, in the Western Region of Ghana, approximately 320 kilometres by road, west of Accra, the capital of Ghana, West Africa. In the Financial year ended June 2007, the operation mined a total of 108 million tonnes of which 22 million tonnes was ore. The mined ore is processed through three gyratory crushers supplying two heap leach pads (North and South) and a carbon-in-leach (CIL) plant. Before the 6 Sigma project commenced, the current fragmentation was resulting in sub-optimal feed size to these crushers. It was decided to use 6 Sigma methodology to improve the fragmentation. A defect was defined as a fragmentation analysis indicating less than 95% passing 750 mm. The objective was to improve fragmentation in order to achieve a constant throughput to the north heap leach crusher of 1500 t/hr, a 5% increase in pit loading efficiency and a 50% decrease in rock breaker hours, equipment damage costs and in-pit sheeting costs respectively. However, this was not to be achieved at the expense of grade control as Tarkwa is exploiting a low grade, high volume deposit and therefore ore dilution must be kept to a minimum. This paper is intended to take the reader through the various 6 Sigma phases of the project (Define ? Measure ? Analyse ? Improve ? Control) which have resulted in a 10% reduction in loading times, of which half has been attributed to improved fragmentation, as well as a substantial increase in blasted stocks. The focus has been on both drilling and blasting parameters as both processes had to be taken into account. These parameters are technical but personnel factors were also identified and dealt with as they arose. In order to measure the impact of any change in the process parameters on the fragmentation size distribution, cameras have been acquired. One has been installed looking into the bowl of the north crusher and the other one was dedicated to field observation, of individual blasts. Both are used for on-going fragmentation analysis. At Tarkwa, mining efficiency is strongly dependent on good fragmentation as well as the presence of un-blasted ?toes? on the pit floors. Crusher throughput depends on an acceptable ore fragment size. Compliance to plan with regards to actual hole depths was temporarily monitored by manual hole dipping, but, this is now being replaced with a fully automated Drill Data Management system developed by Sandvik and Modular Mining. The Six Sigma methodologies, using control charts based on data collected in the field, allowed the mine to improve methods with regards to the control of blasted material. It also enforced the implementation of a quality control programme encompassing the entire Drill and Blast process.

Jan 1, 2008

By George A. Grandy, D. W. Fuerstenau

Simulation of nonlinear grinding systems is discussed in the context of the size-discretized batch-grinding model. A linear approximation of environment-dependent (or nonlinear) selection functions is postulated for systems which exhibit feed grinding orders less than unity. For this, a convex linear combination of zero and first-order selection function forms is used to obtain an analytical solution that can be used for simulation. An example in which marked nonlinear behavior occurs is rod-mill grinding. Accordingly, a series of grinding experiments was carried out in a batch laboratory rod mill to test these techniques; agreement between experiment and the model was found to be very good. Recently, significant progress has been made in the simulation of linear grinding systems by using a population balance mathematical model. Herbst and Fuer-stenaul presented a parameter estimation scheme that can be used with the size-discretized batch-grinding model, and Gumtz and Fuerstenau3 have extended these techniques to the simulation of locked-cycle grinding. Grandy et aL." summarized the simulation of linear systems and noted important alternate solutions to the batch-grinding equation. Kelsall et a1.'-" discussed the dynamic simulation of linear batch grinding, as well as linear open and closed-circuit grinding. In all of these, the key word is linear, which certainly restricts the engineer trying to simulate a variety of grinding systems. This paper discusses an approach for the simulation of non-linear grinding systems, particularly those which exhibit grinding orders less than unity. Experimentally, dry rod-mill grinding is used to evaluate the technique presented. Batch Grinding Model The size-discretized batch-grinding model has been discussed in detail by Mika et al.'.' and by Herbst and Fuerstenau,' and therefore, will only be briefly developed here. The model is formulated by making a differential mass balance of each size fraction in such a manner that the equation parameters are precisely defined in terms of selection and breakage functions,' which can be either calculated'.' or estimated1 from experimental data. The model is phenomenological because it averages all stress-application events in the system and, therefore, does not distinguish the manner in which individual particles are stressed.' For this average environment, the resistance of all particles in a size fraction to breakage is defined by that size-frac-tion's selection function; and when fracture occurs from an average event, the breakage product size distribution is defined again by that size-fraction's breakage function. The model is deterministic and is derived in terms of a continuous time variable and a discretized size variable,' i.e., the n mass fractions associated with the n defined size intervals (see Table 1 for nomenclature).

Jan 1, 1971