Search Documents

By R. H. Jacoby, V. J. Berry, R. C. Koeller

The experimental phase behavior of several field gas-condensate systems, one field volatile oil system, and a series of synthetic systems having gas-oil ratios from 2,000 to 20,000 scf/bbl stock tank oil was measured. The data were used to calculate the depletion performance of the field systems at their respective reservoir temperatures and of the synthetic systems at various temperatures. The results of the performance calculations were used to prepare correlations of total stock tank oil and separator gas in-place, and the amount of each recovered by primary depletion. Data needed to use the correlations are initial gas-oil ratio, initial tank oil gravity, reservoir temperature and reservoir pressure. The correlations presented should be useful for estiinating recovery from reservoirs producing volatile oils or rich gas condensates having gas-oil ratios from about 2,000 to 30,000 scf/bbl of stock tank oil. INTRODUCTION Prediction of depletion performance for gas-condensate reservoirs usually requires extensive laboratory work or lengthy phase-behavior calculations. For many small gas-condensate bearing zones the expense of such work is often not justified. Furthermore, where large holdings are involved, it is useful to have estimates of future oil and gas production in advance of the results of a laboratory analysis, even if such work is ultimately planned. For these reasons, it would be of value to have a method for rapidly estimating the depletion performance of gas-condensate reservoirs from the type of field data usually available. Few data on the reservoir depletion performance are available for the purpose of developing correlations. The increasing number of gas-condensate discoveries and the advent of high-speed computers have stimulated the development of methods for predicting performance. Such calculated performance data have been shown to be reliable and are becoming accepted as a basis for reserve estimates and for engineering studies. It therefore seems satisfactory to use results of performance predictions themselves for the purpose of developing the desired correlations. Such an approach is described in this paper. Several rich natural gas-condensate systems (gas-oil ratios of from about 3,600 to 60,000 scf/bbl) and one natural volatile oil system were studied (2,363 scf/bbl). In addition, to provide a more systematic basis for correlating purposes, a series of related, synthetic reservoir fluid mixtures was also studied (GOR's from about 2,000 to 25,000 scf/bbl). The purpose of this paper is to show how the recovery of oil and gas by primary depletion may be estimated from surface gas-oil ratio, reservoir temperature and pressure, and tank oil gravity. procedure Experiments Companion samples of gas and oil were collected from the high pressure separators in nine different fields at the time of their discovery. These samples were each recombined in accordance with the respective producing GOR to reproduce the reservoir fluids. Eight of these fluids, designated F-2 through F-9, were rich gas-condensate systems at the respective reser-

By A. L. Holmes

Significant technologic advances were made in open pit mining during 1973. The industry faced mounting problems on one front where expansion of stripping activities encountered enlarged public resistance and on another where manpower and materials were in short supply. These challenges, along with the challenge and opportunity to meet the increased demand for mining products including materials for energy production, placed a premium on technical developments and their application. The demands on technology also included the providing of facilities and methods to economically extract minerals from deposits of lower grade, lesser accessibility, and where other uses of land approached the value of its minerals. Detection of Failures in Slope Walls The Bureau of Mines has undertaken research directed towards providing a mine operator with the opportunity to take corrective action before a potential slide becomes a problem.

Jan 2, 1974

By S. Y. Fantaye

This paper discusses the design, construction and performance of a 30 inch thick diaphragm wall recently constructed in Baltimore, Maryland at Inner Harbor East. The project site is an established marina and waterfront property. The geologic profile consists of fill, alluvial silt and clay, Potomac sand and clay, decomposed rock, and weathered rock on top of gneiss bedrock. The approximately 1,300 ft long perimeter diaphragm wall serves as a water cut-off, perimeter basement wall and support of excavation for the high rise project?s five levels of below-ground parking. Due to the fast track construction and the tight schedule, the initial design of the diaphragm wall was based on a limited amount of geotechnical information. Supplemental borings were then performed along the alignment of the wall to verify the design assumptions and wall depths. Additionally, the design criteria required that the wall be keyed into a competent stratum with low permeability. The Engineer of Record for the diaphragm wall, Mueser Rutledge Consulting Engineers (MRCE) completed the design and produced accelerated construction documents allowing the developer to release the drawings early for bid. This paper describes the theoretical soil parameters used to develop the loads, moments, and shears for the design of the diaphragm wall and the temporary tieback anchors. It also discusses the refinement of these soil parameters using the observed wall displacements and tieback pre-stressing forces as a baseline. This paper compares the calibrated parameters to the values used in the design of the wall. It explains how the soil structure interaction model was developed and the soil parameters calibrated using PLAXIS 2D non-linear finite element software. The paper also discusses the use of the proprietary CWS joint by Soletanche/Inquip JV as end stop between consecutive wall panels and the unique top-down construction utilized to support the diaphragm wall at the Southeast double re-entrant corner.

Jan 1, 2008

By E. I. Radzinovsky, D. W. Dareing

This paper presents theory which is used to predict rock-bit bearing life reduction due to simple harmonic variations in bit forces. The theory is based on the premise that if a constant load acts for a certain fraction of the life which the bearing would have if that constant load were applied for its entire life, then the same fraction of thelife of the bearing is consumed. Total bearing life is related to simple harmonic variations in bearing life associated with instantaneous bearing loads. The results show that rock bit bearing life is not affected appreciably by forces commonly impressed upon a bit, but it is affecied appreciably by relatively large dynamic bit forces occasionally encountered during drilling. In addition, the results show that the life of sealed bearings is more sensitive to bit force variations than is the life of unsealed bearings. INTRODUCTION Roller bearings are important components in roller cone rock bits because they transmit a large portion of the drill collar weight to the formation being drilled. Unfortunately, they have a relatively short life under down-hole drilling conditions. Roller bearings are usually the first bit components to fail, and their failure leads immediately to failure of the entire bit. Short roller bearing life, and thus short bit life, is due mainly to high unit loads transmitted by the bit and to the adverse environment in which the bearings operate. The results of the study discussed in this report show how dynamic bit forces also affect roller bearing life. The purpose of this paper is to discuss theory developed to predict the effect of different magnitudes of periodic bit forces on roller bearing life. Theoretical results are used to compare the life of rock bit roller bearings subjected to steady forces to the life of rock bit roller bearings subjected to unsteady forces similar to the type of unsteady forces measured at the bit with a special downhole recording instrument. BACKGROUND AIanufacturers of bearings have conducted laboratory tests which show how bearing life is affected by steady bearing load. 1 The well-known empirical equation which defines bearing life follows from bearing test data. It is: where L = bearing life, hr P = bearing load, Ib C = constant q = exponent (constant). The effect of environment on bearing performance is manifested through the exponent q and the constant, C. King,2 in similar tests conducted on roller bearings used in rock bits, showed that, in addition to the load, the environment (abrasive materials, chemical components, etc.) greatly affects bearing life. His data, which show how the life of roller bearings in a 7-7/8-in. W7R bit rotating at 60 rpm is affected by bit weight and fluid environment, are displayed on a log-log plot by broken lines made up of straight line segments. Each broken line corresponds to a given environment. One segment (q = 1.4) of the broken line corresponding to a fluid environment of barite mud is shown in Fig. 1 along

Jan 1, 1966

By Elaine T. Cullen, Albert H. Fein

Federal law mandates that all miners receive safety and health training when first entering the mining industry and at least 8 hours annually thereafter. Although the mining industry has historically relied on an experiential master-apprentice model for training new employees, the formal safety training provided to miners is generally done in a classroom, with mixed results. In a series of stakeholder meetings held by NIOSH across the West in 1997-2000, trainers identified significant gaps in materials that were available to teach new and experienced miners. They asked whether NIOSH could develop effective materials to fill these perceived gaps, as well as make training more effective for those who were required to attend, but who often refused to be attentive. Adult learning theories, social learning theories, mentoring, and storytelling were all employed in the development of a series of safety training videos that have become very popular in the mining industry. This Report of Investigations describes the theoretical frameworks that were used, the process that was developed to produce the videos, and the results of the evaluations as to whether or not they were effective in training new and experienced miners.

Jan 8, 2005

By N. P. Goss

ASTERISM appearing in X-ray Laue dia-grams is an extremely sensitive index of changes in the internal structures of indi-vidual grains of polycrystalline metals. It indicates the existence of various forms of subboundary structure or subdivision within the grain. The present viewpoint is that the grain is made up of lattice blocks having substantially the same size and shape.1-4 When these blocks all assume exactly the same orientation, the crystal is perfect and asterism is absent. Cleaves and Thompson5 observed that the hardness of iron is virtually constant over a range of grain sizes. It is quite possible that the subboundary structure caused this, and that the latter is just as important as grain size itself. While the experiments reported here are not con-clusive, they do support this viewpoint. Metals can, under certain conditions, be prepared entirely free from asterism, but this preparation does not necessarily require long heating or slow cooling, as will be shown here. In this paper a distinction is made be-tween mosaic and distorted grain struc-tures but the difference is only a matter of degree. In a previous paper9 it was shown that the grains can become distorted even during heat-treatment. The block structure exists inherently, even in a perfect crystal; the size and shape of these crystallites, or lattice blocks, varies, depending upon a number of factors. Goetz, for example,7 has shown that a metal before crystallizing from the molten state must go through a paracrystalline phase with oriented groups of atoms about 10-14 to 10-15 c.c., or 10 5 cm. in size.

Jan 1, 1940

By W. H. McFarland

The mechanical properties have been determined for a large number of alloy-free martensitic steels with carbon contents ranging from 0.08 to 0.20 pct and with manganese contents of about 0.4 to 0.5 pet. These steels were tested 1) as water-quenched, 2) after quenching, temper rolling, and tinning, and 3) after tempering treatments which involved temperatures from 400o to 1300oF and times from 1 min to 8 hr. The majority of these tests represent steel from commercial-size coils, i.e., strip 32 in. wide, coil weights up to 20,000 16, and steel thicknesses from 0.0055 to 0.024 in. As a result of these treatments, it has been shown that as-quenched low-carbon alloy-free steels can be produced with tensile strengths ranging from 140,000 to 220,000 psi and tensile elongations from 3.0 to 4.0 pet in 2 in. The tensile strength of the as-quenched martensites can be represented by the equation, tensile strength (ksi) = 119 + 560 (wt pet C). The response to tempering of these steels is related to previous work by Muir, Averbach, and Cohen and by Grange and Baughman. Strain aging of low-carbon martensite has also been investigated. If low-carbon steels are defined as those steels with a maximum carbon content of 0.2 pet, it is found that the literature on low-carbon, alloy-free martensites contains little data on the mechanical properties of these steels. However, the following facts concerning low-carbon alloy-free martensites seem firmly established:'-' 1) The major factors in controlling the strength of the martensite appear to be a) fine structure, b) the internal strain resulting from the transformation, and, particularly, c) the amount of carbon in solid solution. 2) In low-carbon steels, the martensite is auto-tempered and is in the form of needles with only minor amounts of internal twinning, whereas the martensite in high-carbon steels forms as plates which are internally twinned on a fine scale. 3) Care must be taken in comparing the results of work that has been done on low-carbon steels with varying amounts of alloying elements to data on plain carbon steels. As has been noted by Irvine, Pickering, and Garstone,6 alloying elements generally lower the martensite start temperature and, thereby, decrease the amount of auto tempering obtained during the quench. This makes it difficult to

Jan 1, 1965

By M. R. Tek, M. L. Katz

The flow of fluids in stratified porous systems, in which adjacent layers of the system are in communication over part or all of their common interface, in many instances involves crossflow between layers. A theoretical study has been made of the unsteady-state flow of slightly compressible fluids during depletion of bounded stratified porous systems. Consideration has been restricted to single-phase flow, with negligible capillary and gravity effects. Analytical expressions have been derived for pressure distribution and for (luxes at the producing face in two-layer systems with complete fluid communication between layers. These expressions occur in the form of double Fourier and Fourier-Bessel series. The method of extending the solution to any number of layers is demonstrated by deriving the equation for pressure distribution in a three-layer system. On the basis of the exact results for two-layer systems, certain generalizations regarding the behavior of stratified systems in general are presented. The performance of stratified systems, in terms of cumulative flux as a function of time, is shown to lie at all times between bounds established from single-layer theory. The upper bound is given by treating the system as a single layer with arithmetic average physical properties. The corresponding lower bound is the summation of the fluxes from each layer as treated individually. Variation in performance of stratified systems between the upper and lower bounds is determined by the extent to which crossflow occurs in the system. The principal parameters affecting the amount of crossflow are the vertical permeability of the system, the ratio of system thickness to "radius of drainage" and, for radial systems, the ratio of system thickness to interior radius. At very early times, the system performance is near the lower bound. As time and the radius of drainage increase, the per- formance tends toward the upper bound. INTRODUCTION One of the principal problems confronting the reservoir engineer today is the incorporation of the effect of reservoir heterogeneity into predictions of reservoir performance. The first part of this problem is the characterization of the actual reservoir heterogeneity in a mathematically useful manner.1, 2 It is then necessary to calculate the effect of this heterogeneity on the system performance. It is frequently possible to estimate this effect by comparison with the known behavior of an idealized system. One such idealized system is the stratified or "layer-cake" model. Many studies have been made of the behavior of stratified systems, from both a theoretical and experimental standpoint. The great majority of the theoretical studies have been concerned with systems of separated layers, with no fluid crossflow. Among the more noteworthy of such theoretical papers is that recently published by Lefkovits, et al,3 in which a comprehensive analysis was presented for the behavior of bounded stratified systems which are unconnected except at the wellbore. Three recent references have dealt with stratified systems including the effect of crossflow. Jacquard4 has presented mathematical derivations pertaining to depletion of two layer systems producing at constant rate. A doctoral dissertation by Katz5 contains analytical solutions and tables of results for pressure distribution and fluid flux during constant-terminal-pressure depletion of two-layer and three-layer systems with crossflow, together with tables of eigenvalues necessary in the computations. The dissertation also presents results from experimental studies of stratified systems using a heat-transfer analog model. This paper is largely based on the material in this dissertation. A third paper has been presented by Russell and Prats6 since completion of the work resented herein, containing mathematical derivations for and discussion of the behavior

By W. R. Ingalls

In reviewing the history of the metallurgy of zinc, I shall pass hastily over what is only of antiquarian interest. That has been excellently treated by Dr. Bernhard Neumann in "Die Metalle" (1904) and has been described briefly in my "Production and Properties of Zinc" (1902), in my "Lead and Zinc in the United States " (1908), and in other metallurgical works of more or less the same date. In this present monograph, I have it in mind to confine myself mainly to technical practice, especially to that of the last 75 years, prior to which period advance was slow and of no great moment. The ancients made brass by the cementation process, i.e., embedding copper in a mixture of calamine and carbon and heating, whereby zinc oxide was reduced and zinc was vaporized and combined with the copper. Zinc was isolated by some of the alchemists, who named it and knew something of its properties, but made no use of it. Long before then, however, zinc was produced in India. Later it was produced in southern China. Possibly the Chinese obtained their knowledge from India. The Chinese in remote places still produce small quantities of zinc. I have seen photographs of their furnaces; or pots, for they hardly deserve the dignity of being called furnaces. I imagine that they are the same that were used centuries ago, for I cannot conceive of anything more primitive. Anyway, it is certain that the idea of a commercial production of zinc in Europe was imported from the Orient, where the metal was known in commerce as Speauter and Spiauter, whence speltrum and finally our term spelter. Tutanego and Tuteneague are other old names. Dr. Isaac Lawson went to China about 1730, expressly to discover the method of its production. What connection there was between Isaac Lawson and John Champion we do not know, but the latter obtained in 1739 a patent for a process of distillation downward and at some time between 1740 and 1743 erected a works at Bristol and actually began the manufacture of spelter. A production of 200 tons per annum is mentioned. In about the year 1766, Rishop Watson visited the Champion works and saw the process in operation, which previously had been

Jan 1, 1937

By H. N. Eavenson

EaRly in 1917, the United States Coal & Coke Co. secured options on several tracts in Harlan County, Ky., aggregating about 19,000 acres in area, and after careful prospecting by outcrop openings and diamond drilling, completed the purchase late in July of that year. This property is situated in the eastern end of Harlan County, south of the Poor Fork of Cumberland River, and extending across Big Black Mountain to the Clover Fork of Cumberland River, a distance of about 7 mi. (11.3 kg.). It extends from the Kentucky-Virginia line westward for about 6 mi. Looney Creek, which empties into Poor Fork, crosses the property for about 4 mi. (6.4 kg.), and as several of the seams within the property outcrop along this stream, it afforded an easy, and the logical, place for development. The property is on the northern side of the geological trough formed by the uplifting of Stone Mountain, on the southern, and Pine Mountain, on the northern side; the northern boundary along Poor Fork is practically at the base of Pine Mountain. This area has been described in various geological reports. The main seam on this property is the one known variously as the "C," Benham, Keokee, Taggart, and Roda; it is also called, by the Kentucky Geological Survey, the Kellioka seam of the western portion of Harlan County. This seam averages, in this property, about 5 ft. (1.5 m.) in thickness, although local rolls reduce this thickness considerably over small areas, and at the extreme western end of the property the seam splits. It is usually clean, although occasionally a small parting occurs within a few inches of the bottom of the seam; it is one of the best coking and gas coals in the United States. The average analysis of this coal is given in Table 1.

Jan 1, 1922

By C. W. Hoffman, W. R. Hinken

Probability sizing, a fairly recent development in the field of particle separation, is now under investigation to determine its value to the mining industry. The method employed is probability sizing through a vibrating network of decreasing screen openings. While probability sizing is not new, the possibility of using it for coarse, highly abrasive ores at high tonnage rates has only recently appeared to merit practical consideration. The advantages of probability sizing vs. conventional screening methods are: (1) reduced space requirements for a high capacity unit, (2) fewer moving parts, (3) more versatile product sizing selection, (4) reduced maintenance requirements, and (5) lower power consumption. Screening is a necessary part of virtually every crushing circuit. At some stage in the process, particle separation becomes a controlling factor in the operation. The basic type of screen in use today is the vibrating unit, which usually employs a mechanical vibrator of one type or another to obtain sizing and material transportation across the screen surface. The vibrating screen has its limitations and inherent problems. Operators must live with: (1) high maintenance — worn rods, screen cloth, spacers, cross members, chutes, etc., (2) low capacity in relation to floor space requirements, (3) extreme noise levels, (4) high power consumption, and (5) structural problems in the screens and supporting steelwork. All plant operators have become tolerant of these drawbacks through the years, and little innovation has been developed in screening. The vibrating screens in use today incorporate improved metals, more efficient power sources, better lubricants, and increased manufacturing skill, but the basic machine itself remains unchanged. Screening is a relatively small part of most plants' operating expenditures and gets relatively little attention from research and development. The HiProb sizer is a new approach to the problem of particle separation on a high tonnage basis. Developed by Dr. Fredrik Mogensen (president of Fred-rik Mogensen, A. B. of Djursholn, Sweden), this unit has found its primary acceptance in the sizing of wet or dry materials in the fine ranges. Climax has been working cooperatively with Mine and Smelter Supply Company, the United States licensee, on the adaptation of the sizer to obtain consistent recovery at a high tonnage rate on a — 3/8-in. separation. This was a new application for the sizer and opened up a whole new field of problems. Dr. Mogensen's machine utilizes the control of normal probability of falling particles and is designed to eliminate some of the undesirable features of vibrating screens mentioned earlier. The machine is light, compact, consumes less power than conventional screens and has a low noise level. PRINCIPLES Probability sizing is a process designed to allow solid particles to segregate with a high ratio of the materials reporting into their respective size fractions with a minimum amount of misplaced particles. Sizing is defined in this paper as segregation of dry solid particles into fractions of comparable sizes. Probability is usually estimated as the ratio of the number of ways an event might occur vs. the total number of allowable ways. The probability process described depends upon the fact that particles falling through a network will segregate across the sizing surface even though all openings are larger than the particles. The degree of segregation is dependent upon the particle size and the trajectory applied by the sizing network to each falling particle. Specifically, the process utilizes a maze made up of screen cloth to control the path of a particle in free fall as illustrated in Fig. 1. The usefulness of this probability sizing process is dependent upon the degree of efficiency of an effective maze. Primarily, a maze must be extremely flexible to meet the multi-faceted nature of solid particles and, at the same time, the degree of control must be reproducible so that a desired separation is predictable. Dr. Fredrik Mogensen has formulated a maze that is not only flexible and easily controlled, but, mote importantly, easily adaptable to a working machine.

Jan 1, 1970

By T. E. Schmieman, J. E. Miller, M. L. Rizzone

Both centrifugal and reciprocating-type pumps have been widely used in the transport of slurries. Although with some limitations, centrifugal pumps may be used, especially for short-haul systems, however, for the long pipelines the reciprocating pumps are better suited. A state-of-the-art review is presented in which a discussion of applications is made and some of the problems associated with meeting the proper design conditions for satisfactory service are discussed. Several developments underway give considerable promise of better pumps in the future, although the current level of development provides for an economical means to move slurries. The movement of liquids in pipelines necessarily occasions the use of pumps. The petroleum industry is familiar with the transport of solids through mud pumps and cementing and fracturing pumps where the movement of slurries is an everyday matter. In the drilling of an oil well, the circulating fluid utilized to remove drill cuttings is called drilling mud. This substance is usually a fairly sophisticated material designed to develop certain characteristics desirable in the drilling process. The cuttings are suspended in a moving column of this fluid and brought to the surface. The separation of the cuttings from the drilling fluids is accomplished by the use of shaker screens and settling pits; however, it is impractical to remove the cuttings completely and as a result they are pumped through the mud pumps back into the circulating stream. Over the years, mud pumps have been improved so that rather long life can be obtained from liquid end parts subject to the attritional effects of the abrasive-laden fluid. It is from this background that reciprocating-type slurry pumps have been developed. Centrifugal Pumps Centrifugal pumps have also been used to transport solids, where low heads are required, typically up to 200 ft or so, and for short hauls. The centrifugal pump is a hydrokinetic device wherein the increase in velocity of a fluid stream is converted to head, and to achieve high heads a large change in velocity is necessary. Abrasive laden fluids cause wear on impellers and casings as a result of erosion by the fluid and the suspended particles. Centrifugal pumps, therefore, can only be used where the internal velocity of flow is rela- tively low. The advantage of centrifugal pumps is their high capacity at relatively low capital cost and usually relatively small space requirement. One of the disadvantages of the centrifugal pump when used in slurry pipelining can be seen in its typical pressure-volume performance relationship, which tends to work against the application (see Fig. I). If an increase in pressure (head) is occasioned by flow restrictions in the pipeline, say by the dropping out of solids, a desirable characteristic of a slurry pump would be that it develop increased pressure to overcome the restriction. The centrifugal pump provides the increased pressure only at the expense of considerably reduced volume which then results in a lower flow velocity. With the reduced flow rate, adequate velocity to hold the material in suspension and keep it flowing in the line might not be achieved. If centrifugal pumps are considerd for the movement of solids in a long line, a series of pumps must be staged in order to provide the necessary motivating force. A large number of pumps in the line would be required, since each of the pumps could provide only a small pressure increment. An equal number of standby pumps

Jan 1, 1971

Pisolitic iron ores (also known as channel iron deposits) are an important resource of medium-grade iron ore in the Hamersley Province of Western Australia. They are a special case of transported pisolitic ferricrust, differing from normal transported ferricrust only in the exceptionally high iron and low alumina content. The pisoids typically range up to 5 mm in diameter with abundant particles of ferruginised fossil wood up to 15 mm in maximum diameter preserved in the sediment. Field observations indicate that pisoliths are commonly initiated by the action of raindrops on iron-rich soil. Pisolites form by the impact of raindrops forming coated beads of ferruginous soil, which after dehydration obtain additional coatings during successive showers. Thick deposits of pisolite that are transported and deposited primarily by sheetwash form in the distal regions of the pediment. A size range limited to particles that may be transported by extremely shallow water characterises the abundant fossil wood fragments. The absence of fine sedimentary layering in pisolitic iron ores is explained by the action of soil-forming processes after deposition, while the major coarse bedding features derive from successive erosional and depositional events in the evolution of the pediment. They are not deposited in channels by rivers which, in arid to semi-arid conditions, typically deposit quartz sands and gravels with characteristic point bars and current bedding, abundant ferruginous granules, but rarely pisoids. However, they may fill abandoned river channels.

Jan 1, 2007

By R. W. Ph. D. Raymond, Anton Filers, O. H. Hahn

THIS paper will treat of such works only as beneficiate ores directly in the mining districts. And when it is said that more than twenty furnaces exist in Utah, about as many in Nevada, five in Montana, and four in Cerro Gordo, Inyo County, California, it is obvious that a business so extended deserves attention. Wide apart as these different works are located, they have nevertheless to deal in nearly every case with the same or very similar circumstances and conditions, so that, with very few exceptions, virtually the same system of smelting is followed in all these establishments. This is the so-called method of reduction and precipitation in blast-furnaces. As the principal reasons for the employment of a blast-furnace process are to be considered : the low percentage of lead in the ores, the high price of the only available fuel, charcoal, and the exorbitant rates demanded for labor. The reasons why the reduction and precipitation process is preferred to a roasting, reduction, and precipitation process are the high prices of labor and materials, and the preponderance of oxidized ores over sulphurets, though in some cases the latter are quite abundant. The weight of these reasons will be better understood when the character of the ores to be treated and the object of the smelting are more minutely stated. The ores are in nearly all cases a preponderating mass of oxidized lead ores, such as cerussite, anglesite, and leadhillite, in which nests and nodules of undecomposed galena occur. Associated with these are : in Eureka, Nevada, arseniate of iron and arsenical pyrites, hydrated oxide of iron, quartz, and calcareous clay ; in Little Cottonwood Canyon and American Fork, Utah, iron oxide, and in some cases a combination of antimony, the nature of which I have not ascertained; also dolomite and quartz in widely varying proportions; in Bingham Canyon, Utah, only quartz and comparatively little oxide of iron, or iron sulphurets; in Cerro Gordo, California, oxide of iron, iron pyrites, antimonial compounds, copper ores, and, as gangue, carbonate of lime and quartz. In Argenta, Montana, occur, besides the above-named lead ores, pyromorphite, and molybdate of lead. The preponderating gangue of the Argenta ores is quartz, and there is here a larger proportion of galena than elsewhere in the West. In most of the localities named, the lead ores themselves contain sufficient silver to render its separation from the ore the main object of the smelting; but in some of the districts, and especially in Montana, the lead ores serve only to furnish the extracting agent for the silver of true quartzose silver ores, which at the same time contain a sufficient percentage of lead to make amalgamation impracticable. They are therefore beneficiated by smelting, although the lead itself has no market value.

Jan 1, 1873

By P. V. Faragher

A METAL or alloy finds its place in commerce in proportion to its ability to serve certain purposes better and more economically than other materials. While there is some overlapping of the fields of application of the various metals under discussion in this symposium, each one has its uses for which it is especially adapted. While aluminum is the most recent of the metals to enter the field, the development of the industry has been based on its peculiar properties, by virtue of which new uses for non-ferrous metals have been created. There has been substitution of this new metal for other members of the group but there has been a far greater development in entirely new fields. In common with the other non-ferrous metals, aluminum is resistant to atmospheric corrosion. It also withstands the action of many of the common chemical reagents, strongly alkaline substances being the notable exceptions. The outstanding properties on which the application of aluminum is based are its low specific gravity and its ease of fabrication into the forms in which it is used. It is noteworthy that this property of specific lightness is retained in all the commercial aluminum-base alloys. This statement does not apply to aluminum bronze; this is more properly a copper-base alloy, since aluminum enters into its composition to the extent of only about 10 per cent. None of the commercial casting alloys of aluminum has a density exceeding that of the parent metal by more than about 10 per cent., and some are actually lighter. In the so-called "strong alloys" of aluminum in which strengths comparable to that of mild steel are developed by heat treatment, the greatest increase in density is only slightly more than 3 per cent., and one of these, also, is lighter than aluminum. This property of lightness combined with the desirable mechanical properties of the alloys, makes aluminum especially suited for parts of moving assemblies where saving in power, as well as a decrease in stresses resulting from inertia and vibration, are of importance.

Jan 1, 1928

By E. Chin

Bangladesh, whose population probably passed 100 million by yearend, remained one of the poorest countries in the world, with a per capita gross domestic product (GDP) of $126.2 Its only economically significant mineral production was natural gas. A few other minerals or mineral-based commodities were also produced, generally for local consumption. These included cement, clays, nitrogenous fertilizers, limestone, salt, steel, and pilot plant production of ilmenite and rutile. Exploration for oil was a continuing quest, which was hindered by a lack of funding and a hesitancy on the part of foreign petroleum companies to make long-term or expensive exploration commitments. PODUCTION AND TRADE Production of natural gas continued to increase as more use was being made of the abundant gas reserves variously put at between 7 and 16 trillion cubic feet. The main consumers were nitrogenous fertilizer producers and electric powerplants, but other industries were converting to natural gas from imported coal or fuel oil wherever possible.

Jan 1, 1986

The Morning Session of the Forty-Eighth Meeting of the Rocky Mountain Coal Mining Institute convened in the Little Theater of the Broadmoor Hotel, Colorado Springs, Colorado, at 10:00.a. m.; June 2, 1952, Howard B. Crandell, President, presiding. PRESIDENT CRANDELL: Gentlemen, the meeting will come to order. I presume most: of you have heard the decision of the Supreme Court in the steel case. The decision was six to three that the President had no legal authority to seize the steel industry, and it is reported that the strike is already under way. Gentlemen, it is both a pleasure and an honor to talk to you who come to the meeting of the Coal Mining Institute, many of you, from long distances. Our program committee has suggested that the president give a 30-minute talk, but you may be at case because I assure you I won't take anywhere near that long, when we will pass to more instructive and enlightening subjects. Another reason for the short talk that I am going to make is that many men in this audience know more about coal mining, specialized subjects, than I do.

Jan 1, 1952

By Christopher J. Bise

INTRODUCTION Face haulage in underground mines and pit haulage in surface mines are the principal domains of rubber- tired haulage vehicles. In underground mines, cable- reeled or battery-operated shuttle cars and diesel-powered load-haul-dump vehicles are used; trucks are primarily used in surface mines. Although many concerns go into the selection of rubber-tired haulage vehicles, such as clearance and tire life, the most important factor from a mine-planning standpoint is the production capability of the vehicle in the mine environment. Therefore, this chapter will address this topic. UNDERGROUND FACE-HAULAGE VEHICLES The selection process for underground face-haulage vehicles is, in some respects, much simpler than that of the other haulage systems discussed to this point. It is simpler because these vehicles, which transfer the mined material from the face to the intermediate haul¬age system, are manufactured in various size ranges to cope with the confinement of underground opening widths and heights. However, since these vehicles oper¬ated in an intermittent fashion in conjunction with a constantly advancing face, the system's lack of perma¬nence and overall dynamic nature create a more diffi¬cult situation for predicting productivity. The emphasis in this section will be on prediction of productivity. There are three fundamental steps that must be taken to analyze the productivity potential of any face¬haulage system: l) Recognize the geologic (seam thickness, etc. ) and mining (opening widths, etc.) constraints that affect the velocity/clearance aspects of the haulage equipment, and select equipment from manufacturers' specifications with these con¬straints in mind. 2) Secure the elemental times of the face-haulage system. 3) Incorporate the elemental times into an accepta¬ble mine plan. By recognizing the geologic and mining constraints that affect the system layout, parameters, such as vehi¬cle payload, tonnage to be hauled per cut, and haulage distances, can easily be determined. Elemental times can be developed in two ways: 1) In an existing operation, a time study of the dynamic system can be conducted by placing three time-study engineers at the following static locations; (1) near the loading machine, (2) near the change-out point outby the face, and (3) near the dump. By synchronizing their watches and recording the actions of the haulage vehicles at these three locations, their time studies can be reduced to provide elemental times, such as vehicle tram rates (empty or loaded), vehicle discharge times, and loading rates. 2) In the absence of an existing operation, average values for the elemental times can be provided from other mines operating in similar condi¬tions, or by the manufacturers themselves.

Jan 1, 1986

By W. T. Turrall, M. J. Cook

A discussion of modern developments in beneficiation of fine sizes of anthracite, this paper includes a description of the plant flowsheet, an analysis of operating results, and a summary of fundamentals of mineral separation relative to plant operation.

Jan 9, 1953

By Walter P. Jenney

An investigation, conducted by the author, was begun in September, 1889, by the United States Geological Survey, having for its object the study of the questions bearing upon the occurrence and manner of formation of the deposits of lead- and zinc-ores in Missouri and the adjoining States. The field-work was completed in December, 1891. During the first season the State Geological Survey of Missouri furnished an assistant, and in other ways co-operated in the research within the boundaries of that State. In order that the ore-deposits of the southwest might be compared with those of other sections of the Mississippi valley, an examination was made of the lead- and zinc-mining area of Wisconsin-Iowa, and of the argentiferous lead-mines of the region extending westward from Hot Springs, Arkansas, to Indian Territory. In the discussion of the general geology, and in comparisons between the ore-deposits of the Mississippi valley and those of the Rocky Mountains, the writer has drawn largely from his personal experience, having been engaged for many years in professional work as a geologist and mining engineer in that region. The Director of the U. S. Geological Survey and the Scate Geologist of Missouri have kindly consented to the publication of the present paper. While giving the more important economic results, an endeavor has been made to set forth the unity of plan which appears in the formation of the deposits of lead and zinc of the Mississippi basin, and to show their relation to the argentiferous ores of the Rocky Mountains—that the ores of gold, silver, and mercury, and also of copper, antimony, zinc, and lead, have a universal common origin, irrespective of the geological formations in which they occur.

Jan 1, 1894