Search Documents

By Jeremy Butkovich

Dynamic soil-structure interaction (DSSI) analyses are becoming more common in bridge designs, especially in seismically active areas. Because of its proximity to two active fault zones, the Evergreen Point west approach bridge replacement will be base isolated, and will be designed using DSSI. The project team completed two independent bridge designs to satisfy peer review requirements. The designs required substantial characterization of the soil dynamic behavior using both laboratory and in-situ testing. The analyses made use of earthquake time histories spectrally matched to conditional mean spectra. This led to reduced, and more realistic seismic demands on the structure, compared to conventional uniform hazard spectrum matching. The bridge analyses suggest that the preliminary bridge design is relatively conservative. This will allow the design team to potentially reduce shaft/column diameters and reinforcement. The design team estimates that the dynamic analysis design could represent a net savings of around $60 to $90 million compared to a conventional design.

By Kazunori Matsushita, Masaru Sakakibara, Kenji Harada, Naotoshi Shinkawa, Mitsuo Nozu

The Sand Compaction Pile (SCP) method has been widely used as a typical countermeasure against liquefaction in Japan, and its effectiveness has been confirmed in many case histories of damages caused by the past large-scale earthquakes. A series of studies were conducted to evaluate the effectiveness of the compaction method and other factors, if any, in sustaining a seismic force that is greater than the assumed one and caused no damage. Based on the results of these studies, the Architectural Institute of Japan (AIJ) has indicated in its “Recommendations for Design of Ground Improvement for Building Foundations” published in 2006 that the liquefaction resistance ratio (tl/sz) of the composite ground, which consists of sand piles and surrounding compacted ground, is higher than the RL calculated by using the SPT N-values of the ground in-between the sand piles. In this paper, statistical analysis of safety factor against liquefaction, FL, was performed by using the SPT N-values of ground in Port Island and Rokko Island which were both fully reclaimed islands in Kobe city during the 1995 Hyogo-ken Nambu Earthquake (classified as intense shaking) and, together with the consideration of relative settlement, resulted in tl/sz of the composite ground being 1.5~2.5 times of tl/sz of the soil in-between piles after improvement. Furthermore, the liquefaction resistance curve of SCP-improved sites obtained from the relationship between SPT N-values and cyclic shear stress ratio during the 2011 off the Pacific Coast of Tohoku Earthquake, which was regarded as long-duration earthquake, was plotted to the left side of the curve originally proposed by Japan Road Association. Thus, the liquefaction resistance of the improved ground was found to be higher than that of the natural ground, even for the same SPT N-values, verifying the validity of the AIJ recommendation.

Jan 1, 2017

By H. Cevizci

"Numerical simulation of the plaster stemming method (PSM) was performed and compared with the conventional drill cuttings stemming method (DCSM). Many earlier in situ tests have proved that PSM can use the blast energy more efficiently than DCSM. Despite PSM generating more blast vibrations, it has advantages over DCSM such as better fragmentation and lower cost per unit volume of rock blasted. In this study, numerical simulation with Autodyn software using a 2D tool was employed to prove the efficiency of plaster stemming by comparing parameters such as pressure, Y-velocity, Y-force, internal energy, acceleration-Y, and compression. For example, the maximum pressure attained at the top of explosive column was 7 395 MPa for DCSM whereas it was as high as 11 945 MPa for PSM. Most of the computed parameters were significantly higher in PSM than those obtained for DCSM. This paper is the first study elucidating the efficiency of PSM by numerical simulation. It is concluded that PSM can save substantial amounts of money and effort. IntroductionThe stemming of blast-hole collars in surface mines with an inert material redirects blasting energy to the rock more efficiently, thus the blast-induced energy is utilized more effectively in breaking rock. With proper stemming, the gases should not escape due to loose stemming material. More efficient stemming with better confinement therefore increases the blast fragmentation. In addition, the distance of scatter is increased, giving rise to a looser rock pile that can be more easily loaded and transported. In order to improve the performance of a blast, stemming is used to help maintain the gas pressure over time (Konya and Konya, 2018). Proper stemming has been shown to increase the explosive efficiency by over 41% (Snelling and Hall, 1912).The most common stemming material in open pits and quarries is drill cuttings because of their ready availability at blast sites and the drill cuttings stemming method (DCSM) is a low-cost method. However, it has a major disadvantage in that dry drill cuttings eject very easily from blast-holes during an explosion, thus a great percentage of the blast energy is wasted and lost to the atmosphere. Cevizci (2012, 2014, 2013, 2017) studied blasting parameters in open pits and obtained better results with the plaster stemming method (PSM) in many limestone, basalt, and clay quarries. Moulding plaster is preferred for stemming because of the fast hardening time of 25–30 minutes."

May 1, 2019

Applying DEM to prediction of tumbling mill performance is challenging because several different modes of breakage are active in the process. As our knowledge of breakage and computational capacity improve, it is worth revisiting previous simulation tasks which did not produce a satisfactorily realistic description of a measured process. At SAG 2006, we reported the simulated and measured outcomes of treating a well characterised ore in a 1.2 m diameter mill. This well instrumented, pilot scale mill at the University of KwaZulu-Natal has been combined with some new approaches to ore testing to allow different modes of breakage to be tested. The mill design allows the rate of generation of fine material to be measured in close to real time for autogenous and SAG mill charges. The updated simulation model estimates mass loss with particle evolution and embeds the cumulative damage and breakage. The simulated results are compared with the measured results. Issues such as relating modelling inputs to particle breakage characterisation data and the accuracy of the predictions of the models are discussed.

Jan 1, 2012

By E. H. Christiansen

Gem-quality red beryl in the Wah Wah Mountains of southwestern Utah formed as a post-magmatic mineral in a topaz rhyolite flow. Unlike topaz, this beryl occurs along fractures in devitrified rhyolite, rather than in lithophysal vugs. The flow occupies a graben and perhaps a significant paleo-drainage. Beryl occurs at medial depths within the eroded flow, about 170 m below overlying mafic lava flows. Both beryl-bearing fractures and the host rhyolite show an unusual amount of argillic alteration compared with other topaz rhyolite flows. Alteration may be related to the incursion of surface water along shrinkage fractures within the flow. Whole-rock concentrations of CaO within the host rhyolite are very low (<0.01 % to 0.18%) compared with other topaz rhyolites and Be concentrations (about 20 ppm) are about average. Low Ca activities prevented fluorite precipitation and allowed Be transport as fluoride complexes. Beryl probably grew at subsolidus temperatures (-300-650°C), but above the temperature of kaolin development (200-300°C) as fluoride-rich vapors, released by devitrification, encountered fractures and mixed with vapors derived from surface water flowing through the fractures. Beryllium fluoride complexes reacted with water vapor, silica minerals, alkali feldspar, water, and Fe-Mn oxides along fractures to produce red beryl. Continued reaction of the cooling flow with surface water at lower temperatures probably produced a boiling, more acidic fluid that produced the argillic alteration. Consequently, eruption of low-Ca topaz rhyolite followed by entrance of surface water into medial portions of a devitrifying and still hot lava flow appear to be critical factors that led to red beryl formation.

Jan 1, 1996

By Felicia F. Peng

A laboratory fixed bed reactor was used in a study of generating clean thermal energy from coal fine refuse-limestone agglomerates. The major operation variables, including Ca/S mole ratio, agglomerate size, air flow rate and temperature, which affect the rate of sulfur fixation and combustible material utilization, have been examined. The test results show that 70 percent or more of sulfur fixation and 100% of combustible material utilization can be achieved depending upon sorbent, agglomeration, and combustion conditions. The coal fine refuse limestone pellet combustion process (CLC process) requires a simple flowsheet to convert coal fine refuse as a clean solid fuel, while meeting the strict air quality standards for SO2 emissions into the atmosphere. The CLC process is an attractive method to clean up coal slurry impoundments to protect our environment.

Jan 1, 1984

By W. K. Kleysteuber

This report covers the design and testing of a novel bulk materials conveying device by the Bureau of Mines. The transport concept of the device is to create a traveling wave with a steep front so that the bulk material slides and cascades down the front of the wave with some horizontal motion. Ideally, the front should act like a continuous chute. The concept of moving bulk materials along a belt without any forward movement of the belt itself was demonstrated. The conclusions reached were that the mechanism as designed could not overcome the inherent major disadvantages that would make the undulatory conveyor suitable for practical applications.

Jan 1, 1974

By A. E. J. Gallagher

There are many influences which have a bearing on the economics of industrial minerals production. The purpose of this paper is to discuss briefly three factors which have economic significance in the production of these mineral commodities. The three items of discussion include 1) the nature and relative value of the industrial minerals group, 2) project planning, and 3) market analyses. General aspects of these factors are familiar to most of us. However, an attempt will be made to give some current details regarding each. Also, in reality, project planning and market studies are usually so closely associated that they will be discussed jointly, rather than separately. This will be done by way of examples which show how these two activities actually evolved for two industrial minerals projects.

Jan 1, 1984

By B. D. Thompson

Many mines adopt necessarily conservative backfilling strategies due to a lack of understanding of their backfill behaviour. In the past five years, extensive instrumentation campaigns have focused on measuring in-situ cemented paste backfill behaviour. These tests have resulted in optimised backfilling efficiency through elimination or reduction of cure periods where; i) controls on backfill behaviour are understood, and ii) barricade pressures are demonstrated to be within a safe range using routine monitoring as a required QA/QC procedure. Recently, this work has been extended to consider hydraulic backfill operations. Two stopes have been instrumented at Vale?s Coleman and Garson Ramp mines. The instrumentation and deployment methods are discussed, and representative total earth pressure, pore pressure, and temperature data are presented. In one case, pressures in the stope are relatively low as drainage causes strength gain in the fill and so pressures are arched. In a second example, again, drainage causes strength gain in the fill, but increasing temperatures correlate with pressure increases even during downtimes in filling. These pressure increases are thought to be caused by thermal expansion of the backfill in confined locations. Generally, the instrumentation approach has proven successful in measuring hydraulic backfill behaviour and offers good potential for incorporation into a procedure to safely maximise backfilling efficiency through routine barricade pressure monitoring, when combined with safeguards to ensure adequate fill drainage.

Aug 1, 2013

By S. J. Dai

The cadmium and cyanide are main poisonous components in cyanide electroplating cadmium waste water of an electroplating plant in Shenyang. The content of cadmium is about 26 mg/L and the content of cyanide is about 11.782 mg/L in this waste water. The main form of cadmium and cyanide are ions which are Cd2+and CN?. Because the cadmium and cyanide exceeded the standard seriously, the waste water must be disposed before it discharges. The microbiological method of treating heavy metals in wastewater has many advantages. For example, it has a fast adsorption velocity, high processing efficiency, wide range of pH and temperature, few invest, low running cost, no the second pollution and so on. At the same time, the CN? could be degradated by some microbiology. The physical nature, the chemical nature of Bacillus mucilaginosus, the adsorbing condition and adsorbing regular of Bacillus mucilaginosus to cadmium in the wastewater are studied by using Bacillus mucilaginosus as adsorbent removing cadmium from electroplating wastewater. The experimental results show that the adsorbing rate of cadmium is over 92%, under the room temperature(about 25?), stiring revolution in adsorption being 800 r/min for 30 min, pH being 5 , the bacteria being cultured after 5d with the biomass of Bacillus mucilaginosus 40g/L (wet weight). The mechanism in biosorption process of Bacillus mucilaginosus to cadmium is analyzed and discussed by TEM , Zeta potential,and infrared spectroscopy analysis. The results showed, the chemical involving is main adsorbing form, while electrostatic attraction, ions exchange, hydrogen bonding and Van Der Waals force are concerned cooperatively. ?NH2 ?, ?C=O?, ?C=O?NH?CH2, ?CH3, ?OH are main adsorbing groups. At the same time, the floatablity of removing cyanide by Bacillus mucilaginosus is explored.

Jan 1, 2014

Energy benchmarking is widely applied across industries to determine the potential to improve energy performance. Unlike the many technologies for which energy benchmarks and efficiency rating systems are already in maturity, benchmarking of mining processes is still in its infancy. Benchmarking energy usage in mining operations, where energy costs are high and represent a significant portion of overall operating expenses, is challenging due to the uniqueness of each mining operation. Mines vary in terms of geology, geographic setting, ore body geometry, mineralogy which impact the mining method, material handling, processing and waste management. In order to gauge the opportunity for reducing the energy intensity of individual operations and also to compare the energy performance of operations on a global scale, the deployment of new benchmarking methodologies, models and frameworks is necessary. As a step towards the establishment of an accurate framework for benchmarking the energy consumption of mining operations, comminution, one of the more energy intensive mining sub-processes, was selected as the focus of a new energy benchmarking method. The methodologies and processes used to onset fragmentation in a rock mass to the crushing or grinding of rock to a size that is suitable for economic extraction are predominantly dependent on the ore properties. For this reason, site specific factors, such as the size reduction requirements and ore hardness were included in an energy benchmark model so that the energy performance of comminution processes at different operations could be normalized and compared on a global scale. Single particle compression breakage has been identified by several prominent researchers in the field of comminution as the upper limit of energy utilization in size reduction processes. For this reason single particle compression breakage was proposed as the basis of a work index for ores to be used as an input for the benchmark model. Overall, the new method showed that the energy benchmark for mineral comminution can be normalized and subsequently compared for a range of mining operations once the ore hardness has been appropriately characterized.

Aug 1, 2013

By T. H. Eyde

Natural Zeolites are a less expensive and in certain applications a superior alternative to organic ion exchange resins. Mining and metallurgical waste streams are difficult to treat because the effluents which contain potentially valuable heavy metals such as copper, lead, and silver are often highly acidic and contain significant quantities of suspended solids. Under rigorous operational conditions, certain natural zeolites can remove the metals, which if desired can be recovered by either elution or conventional smelting techniques. There are significant differences in cation exchange rate, selectivity and capacity as well as resistance to either high or low pH, blocking cations and tolerance to elevated or depressed temperature and pressure not only between different zeolite minerals but between the same mineral from different deposits. Applying natural zeolites to the treatment of mining and metallurgical waste streams depends on matching the specific zeolite to the effluent by characterization of the zeolite minerals.

Jan 1, 1994

By Tex M. Kubacki

On August 6, 2007, the Crandall Canyon Mine experienced a collapse which trapped six mine-workers. An MW 4.1 seismic event was recorded in conjunction with this collapse. An additional 54 seismic events were detected and located in the vicinity via routine processing techniques during the month of the collapse. Waveformbased cross-correlation detection techniques have been used to uncover 1,328 small, previously undetected seismic events which occurred near the collapse area between July 26 and August 9, 2007. This work has resulted in lowering the magnitude threshold of completeness from ML 1.6 to ML -0.5, a 2.1 order-of-magnitude improvement over standard processing techniques. Event locations have been computed using a double-difference inversion. The spatial pattern of events ultimately helps to delineate the extent of the collapsed area. It is shown that many of the large catalogued events (>ML1.6) tend to be closely followed by numerous (often 20 or more) smaller aftershocks. Cluster analysis of the known catalog reinforces prior work indicating the existence of seismic clustering on the east and west sides of the collapse. Research now demonstrates that it is possible to differentiate events related to the main collapse from those related to the rescue attempt following the collapse. The cross-correlation techniques described herein greatly improve the ability to detect small mining-induced seismic events. These methods may lead to improvements in assessing seismic hazards for conditions similar to those observed at Crandall Canyon preceding the collapse.

Jan 1, 2013

"A cationic surfactant, tetradecyl tributyl phosphonium chloride (TTPC), was first used as a collector. Flotation characteristics of muscovite using TTPC have been investigated through flotation tests. And dodecyl trimethyl ammonium chloride (DTAC) was tested for comparison. Their adsorption mechanisms on muscovite surface were clarified using zeta potential measurement, DFT calculation and molecular dynamics (MD). The flotation results indicate that the recovery of muscovite decreases when the pH increases in the presence of surfactants. When a maximum of recovery was reached, the dosage of TTPC was 2×10-5mol/L which was half of that of DTAC. Zeta potential measurements confirm that the TTPC displays a stronger collecting power than DTAC and is a superior collector for the muscovite flotation. DFT calculation and MD simulations show that TTPC interacts with the muscovite mainly through electrostatic attraction and hydrogen-bonding. The conclusions drawn from purely theoretical computations matched remarkably well with the experimental results. Keywords: Quaternary phosphonium salts; Flotation collectors; Flotation INTRODUCTION Muscovite mica is widespread in igneous, sedimentary and metamorphic rocks. It has the general composition KAl2(AlSi3O10)(OH)2. Muscovite mica exhibits perfect cleavage along the (001) plane, which exposes interlayer potassium ions[1-3]. In aqueous suspensions, the potassium ions readily enter into solution, leading to the development of a net negative charge on the (001) plane[4-6]. The surface of the muscovite mica is negatively charged at all pH > 1[7]. Due to the negative charge surface over the whole pH range of 2–12, the muscovite mica would not be expected to respond to anionic collectors in the absence of an activator. Conversely, the mineral is readily recovered using cationic collectors. However, until now, various amines and their derivatives (with N atoms as the center) are still the only available cationic collectors which still had their shortcomings such as weak selectivity, low flotation speed. Since few types of cationic collectors could be used, in some sense, the limitations of collectors are increasing significantly and the cationic flotation is facing more and more challenges. Quaternary phosphonium salts, as novel cationic surfactants, are widely used in antimicrobial, catalysis and surface modification field due to their biological activities, hydrogen bonding capability, stability and superior group electrical property[8-10]. There are a number of processes where quaternary phosphonium salt surfactants have shown better properties than quaternary ammonium salts and amines. Although the adsorption of quaternary phosphonium salt surfactants at the bacterium–liquid interface has been studied thoroughly, the case of adsorption in mineral surface has not been investigated thus far."

Jan 1, 2016

By A. Oberrauner

Electrostatic separation is a dry separation technique usable for many applications in the mining- and recycling industries. At the Chair of Mineral Processing intensified research has been done on this topic during the last years. One challenge was to measure the triboelectric charging of fine mineral particles in a triboelectric charging device consisting of an electrically insulated polyethylene rotor/stator assembly. These tests, performed on monomineralic samples, were accomplished in a climate chamber. It was shown that charging of minerals not only depends on rotor speed, feed rate and atmospheric circumstances but also on the properties of the applied electrostatic field. Tests on pure calcite in contact with the polyethylene rotor/stator system resulted in specific triboelectric charges up to +10 nC/g at low relative humidity. With more water present in the surrounding atmosphere, these charging values decreased significantly. However, at higher relative humidity, triboelectric charge values could be maintained after an electrostatic field of positive polarity was applied. Similarly, charging behavior was found with other hydrophilic minerals. The idea behind all these tests was to find the largest charging difference between minerals occurring together in a deposit and to be able to charge them oppositely, assuming that this means good sort ability in an electrostatic separator. The results gained from these investigations are shown. After having obtained many results on charging pure minerals, it became interesting to test the applicability of the charging tendencies on electrostatic separation of fines <100 µm. In order to do so, a separator for fine polymineralic powders was developed, constructed and combined with the triboelectric charging device, all being set up in a climate chamber. This new so-called coax-separator is presented along with first test-results.

Sep 1, 2012

By J. A. Maritz

"The Hedley and Grant formulation for pillar strength has been widely adopted by the South Africa hard rock mining industry. Today, some forty year later, this formula still provides the foundation for pillar strength calculations when designing for stability and utilising pillars in mine layouts. Various mine specific back analyses were conducted to adjust the equation parameters based on underground observations of failed pillars and comparing to the pillar stresses calculated using numerical models. In all these instances, the influence of shear stresses was ignored. The key to more representative pillar strength estimation is a better understanding of the pillar loading environment.In this paper, special mining cases are evaluated and the existence of shear stresses on the pillar loading environment is illustrated. By revisiting some back analysis data for optimisation of the equation parameters, recommendations were made in respect of the influence of the shear stress component and on how this should be considered in determining the pillar strength.INTRODUCTIONCommon practice on flat dipping, shallow and intermediate depth ore deposits in the South African hard rock and coal mining industry is to exploit the mineral resource using a room-and-pillar layout. The design methodology is mainly based on a Factor of Safety (FoS) approach, where the strength of the pillar is compared to the effective load on the pillar. In these environments, FoS values of 1.6 are applied as it was found to correspond to a probability of failure in coal mines of 0.001. As discussed by Ryder and Jager (2002) page 279: “For lack of anything else more substantial, the figure of 1.6 is generally used in hard rock pillar design in South Africa”. Dependant on the designed purpose of the pillar, the FoS might be selected as high as 2.0 where long term stability is required. The factors directly influencing the FoS include the pillar height (which is linked to the mining height), effective pillar width, a rock-strength factor and extraction ratio."

Jan 1, 2015

By R. E. Anderson

Canada encompasses an area of approximately 9,976,000 kilometres. It is comparable in size to the United States, but because of climatic conditions and limited transportation facilities, much of the area is unsuitable for agricultural or industrial development. We have a population of 22,000,000 - most of whom reside within a hundred mile belt paralleling the Canadian-U.S. border. Our principal cities in order of size are Montreal, Toronto, Vancouver, and Winnipeg. We have a total of 10 provinces, each of which elects its own - government. The Yukon Territory and Northwest Territories covering the northern half of the country, are administered by federal government agencies. The mining industry employs approximately 9% of the labour force and accounts for more than 40% of all tonnage shipped on Canadian railroads and inland waterways. In 1974 it produced $4,800 million in mineral wealth. Canada ranks first in world production of asbestos, nickel, zinc, and silver and has significant production of copper, iron, molybdenum, lead and other mineral commodities. During the past decade Canada, like many other western countries, has undergone dramatic economic and social change. This trend is continuing, and its effect on the Canadian mining industry has produced conflicting results. From the industry&apos;s point of view, some of the more negative aspects include a steadily increasing involvement by government at municipal, provincial and federal levels through the imposition of Stricter controls, regulations and taxation policies, a rising tide of nationalism, which advocates public ownership of all natural resources, the spectre of inflation (currently increasing at the rate of 8% per year) and unsettled labour conditions.

Jan 1, 1976

By V. A. Temeng, M. Owusu-Tweneboah, K. Awuah-Offei

The mining industry has long recognized the value of dispatch systems in open pit mines as they reduce load and haul costs. Over the years, researchers have proposed many dispatch systems with various limitations and advantages. The simplest dispatch algorithms are the so called 1-truck-for-N-shovels dispatch strategy. These algorithms are limited by the fact that their objective functions do not consider all the objectives of a mine and cannot be applied to all possible truck-shovel configurations. They are also myopic in nature. However, they are simple and computationally efficient and do not require occasional updates of the upper stage problem as required in multi-stage dispatch algorithms. In this work, an agent-based truck dispatch algorithm that conceptualizes trucks as intelligent agents that make autonomous dispatching decisions to maximize their utility is proposed. The advantages of this algorithm includes utility functions that encapsulate all of management’s objectives and agent’s with broad situational awareness. They are also more suitable for autonomous trucks. We evaluate the new algorithm against a simple 1-truck-for-N-shovels dispatch strategies using discrete event simulation. The simulation results show that the new utility function has significant advantages over 1-truck-for-N-shovels inspired utility functions. Future work will incorporate adaptive behavior into the model via reinforcement learning algorithm. INTRODUCTION In an attempt to optimize truck shovel operations in open pit mines in order to reduce the cost of haulage operation, which according to (Alarie and Gamache, 2002) is estimated to be about 50-60% of the total cost of mining, several effective and efficient strategies have been developed. Optimizing truck haulage systems in an open pit mine is one of the greatest challenges of mining engineering and has been the subject of many research projects. It is important that haulage systems are designed to be efficient, in order to minimise haulage cost, improve profitability and increase the total mine value. Although optimizing the number of trucks required in the operation of open pit mines can help reduce the cost, an effective and efficient truck dispatching system add value by ensuring that the available trucks are used efficiently. With truck dispatching systems, the trucks are normally dispatched between the crusher and dumping station (e.g. waste dumps and stockpiles), and the shovels in order to maximize the total output, obtain grades targets, reduce fuel consumptions and other objectives. Truck dispatching, which can have one or more objectives, is typically subjected to certain operational constraints such as truck and shovel capacities, empty and loaded trucks speed, among others. The problems associated with truck dispatching was first mentioned by Dantzig and Ramser (1959) after they made an attempt to determine the optimum routes of a fleet of delivery trucks between bulk terminals and a service stations. The problem occurs in several industrial systems besides mining (Alarie and Gamache, 2002; Gendreau et al., 2006; Rego and Roucariol, 1995). The dispatching problem, also referred in literature as the vehicle routing problem, has seen a number of modifications and extensions with Bertsimas and Ryzin (1991) presenting a dynamic and stochastic vehicle routing problem, and Ralphs et al. (2003) also adding to the original concept, the concept of vehicle capacity routing.

Jan 1, 2019

By P. K. Jimack, C. E. Goodyer, A. M. Mullis, P. C. Bollada

"We review the application of advanced numerical techniques such as adaptive mesh refmement, implicit time-stepping, multigrid solvers and massively parallel implementations as a route to obtaining solutions to the 3-dimensional phase-field problem with a domain size and interface resolution previously possible only in 2-dimensions. Using such techniques it is shown that such models are tractable even as the interface width approaches the solute capillary length.IntroductionMulti-scale modelling impinges upon many areas of science, engineering and technology where the interplay between processes occurring on disparate length and/or timescales can affect the properties of systems in a complex, and sometimes unforeseen, manner. One such is the processing of materials where interactions at the atomic scale, through the nano- and microstructural scale can have a profound affect on the macro-scale response of engineering components. Here we focus on one such problem, the crystallisation of alloy melts, to illustrate how a range of advanced numerical techniques make the modelling of such systems tractable.The modelling of solidification structures, in particular the growth of dendritic crystals, is a subject of intense and enduring interest within the scientific community, both because dendrites are a prime example of spontaneous pattern formation and they have a pervasive influence on the engineering properties of metals. For alloy systems, which form the vast majority of engineering materials, solidification involves the rejection of both solute and latent heat from the growing solid, forming a coupled diffusion problem in which both the chemical and thermal diffusion equations should be solved. The multi-scale nature of this problem arises from the disparity between the thermal and solutal diffusivities for most liquid metals, which are typically 10-5 m2 s-1 and 10-9 m2 s-1 respectively. The ratio of these two, referred to as the Lewis number (Le =Dia), is therefore typically of the order 10,000 and gives a measure of the multi-scale nature of the problem. In fact, in many cases the thermal diffusivity is so much larger than its solutal counterpart that thermal diffusion is considered instantaneous, wherein the system can be approximated as isothermal such that the multi-scale calculation does not need to be performed. This is certainly a reasonable approach in most conventional castings. However, there is a class of solidification problem in which this approach is far from satisfactory, namely Rapid Solidification (RS). The application of isothermal phase-field models in such situations are highly likely to produce spurious results or to fail totally, particularly for temperatures below To (the temperature at which the free energies of the solid and liquid phases are equal at the concentration of the bulk alloy), wherein partitionless solidification may occur."

Jan 1, 2013

By Pekka Taskinen

The converter-less nickel matte smelting technology (DON) adopted more than 20 years ago in Boliden Harjavalta smelter has been since that applied successfully to the processing of large number of nickel sulphide concentrates of various Ni-to-Cu ratios and MgO contents. The operational point of the technology is far from the conventional primary nickel smelting in the smelting-converting route. Therefore, a careful scouting of distribution equilibria of the base and trace elements in the smelting conditions of DON process has been conducted, in order to obtain quantitative information about the equilibria and thermodynamic properties of the nickel mattes at low iron concentrations, less than 10 wt% [Fe] in matte. The series of investigations has included novel experimental and analytical techniques for increasing the reliability and sensitivity of the phase equilibria as well as the element distribution observations carried out in typical high-grade nickel matte smelting conditions.