Search Documents

By S. Z. Khan, Veerendra Singh, Y. Rama Murthy, S. Prasad, Sunil Kumar Tripathy, Gajanan Kapure

"In this study, a low-grade ferruginous low-grade chromite ore was subjected to reduction roasting by using conventional heating as well as microwave heating. Sukinda chromite ore deposit contains majorly iron-bearing minerals as gangue phase. The magnetic susceptibility of these minerals enhances effectively after reduction roasting. Alteration of crystalline structure and magnetic property of these metals enables separation of low-grade ore by using magnetic separation. Conventional roasting studies by varying the temperature, time of reduction and reductant dosage were changed for low-grade ferruginous chromite ore. Similarly, microwave power, retention/exposure time and reductant dosage varied for reduction roasting studies under microwave environment. It is found that low-grade ferruginous chromite ore can be upgraded by reduction roasting and 61.2% Cr2O3 was recovered with a chromium-to-iron ratio of 1.93 from feed chromium-to-iron ratio of 1. Microwave reduction roasting studies resulted in upgradation of chromium-to-iron ratio to 1.73 with a recovery of 21% Cr2O3.INTRODUCTION The chromite ore occurs as a spinel containing oxides of chromium, iron, magnesium and aluminium. Most of the Indian chromite deposits are of ferruginous (rich in iron content) which indicates the abundance of ferruginous gangue minerals along with chromite. The primary use of chromite ore is towards the production of ferrochrome alloys. Chromite ores with less than 40% Cr2O3 and the chromium-to-iron ratio (Cr-to-Fe ratio) <1.8 is considered to be unsuitable for the smelting process (Tripathy et al. 2012, Tripathy et al. 2012a). A considerable amount of low-grade chromite ore and overburden excavated during chromite mining is getting accumulated every year, causing a threat to the environment. Its disposal poses a significant challenge and, hence, the beneficiation of low-grade chromite ore and its utilisation has been attracting a lot of attention. Different physical method of beneficiation methods is generally employed for the improvement of the Cr-to-Fe ratio (Tripathy et al. 2012, Murthy et al. 2011, Tripathy et al. 2012a, Tripathy et al. 2013, Tripathy et al. 2016, Tripathy et al. 2017, Tripathy et al. 2017a). It is observed that the enrichment of the chromite ore is carried out by using gravity and in some places by magnetic separation. However, the enrichment of Cr-to-Fe ratio from low-grade ferruginous chromite ore is difficult by using the above-mentioned beneficiation methods due to the presence of near gravity and near-magnetic susceptibility minerals along with chromite. However, an alternative beneficiation method is needed to explore for the beneficiation of such mineral deposits. Reduction roasting followed by magnetic separation is an alternative option for the separation of these types of ores which is widely reported for the iron and manganese ore (Li, et al., 2010; Chun, et al., 2014, Rath et al., 2018). These processes are majorly focussed on differentiating the magnetic susceptibility between minerals and subsequent separation by using magnetic field. The main advantage of such method is dry process option along with the pre-processed product for the costly smelting process. Also, the roasting of minerals in a microwave environment is also an active research topic in the recent time. So, the amenability of the separation feature of the roasting process by using conventional heating as well as microwave heating can be can be studied for the low grade ferruginous chromite ores."

Jan 1, 2018

By M. Iberico

A partir de los años 70 se incrementó el proceso de exploración y desarrollo de los yacimientos mineros submarinos. En este sentido, el presente trabajo describe el origen de los depósitos a partir de los descubrimientos de módulos manganíferos en el océano pacífico que hicieron Thompson y Murray. Posteriormente Buchanam demuestra la existencia de módulos ferro-manganíferos en aguas poco profundas ( 200 m. ), de composición diferente de las provenientes de aguas profundas. De otro lado, el trabajo señala también la división de los minerales marinos en tres categorías: las sales disueltas y en organismos, los sedimentos y depósitos en el suelo profundo submarino y los depósitos consolidados e inconsolidados de la plataforma continental. Por último, se describe los procesos de beneficio y las ventajas de la explotación de los recursos submarinos en el futuro de la minería submarina.

Nov 20, 1972

By Bora Okumusoglu, Devon K. V. Mothersille

"AnchorTest is an innovative software package, specifically developed for tablets, that permits ground anchor test data assessment and management in real time. The solution has two components: a front-end tablet app runs on the Apple iPad platform, and a back-end Cloudbased system running on Amazon Web Services with an online cross-platform website, which can be accessed from any PC, tablet or even mobile smartphone. This tool provides full data analysis and data management capabilities and portability to create greater efficiency in the anchor testing process. AnchorTest is programmed to accommodate the major international anchor testing codes and incorporates an intuitive user interface, which is revolutionary compared to conventional engineering software designs. The use of this tool creates an environment where the testing of ground anchors has effectively become a paperless exercise with greater efficiency and access to instantaneous feedback on the performance of anchors in relation to established acceptance criteria.Historically, project personnel record and analyze the results from anchor load tests using spreadsheets and a laptop computer and/or on predesigned paperbased test sheets (usually as a backup of the testing). In addition, the processing of the test results is not typically performed in real time as the testing progresses — the calculations and analysis are performed either afterward while still on site (if a field office is available) or after returning to the office. Undoubtedly, on larger projects containing numerous anchors where multiple anchor tests may be performed at the same time, processing, analyzing and accepting the load test data and results can be especially time consuming, which could cause delays to the construction schedule.DevelopmentThe need for a more automated and digitized approach to record, process and analyze the data from anchor load tests was highlighted at a deep basement project for a mixed-use development complex in Moscow, Russia. The diaphragm wall supporting the structure was approximately 1,970 ft (600 m) in perimeter length and about 148 ft (45 m) deep, with an excavated depth of about 82 ft (25 m), which required six levels of single bore multiple anchors (SBMAs). This project provided a challenge to recording, processing and signing off on the data generated from some 3,600 3-unit SBMAs. More specifically, for this project, three hydraulically synchronized stressing jacks were used to stress and proof test each 3-unit SBMA, which resulted in nearly 10,800 data plots of the load-extension tests being generated. This project served as the main impetus in the conceptual design and optimization of AnchorTest."

Jan 1, 2017

By M. Rubinstein, N. C. Koon, B. N. Das, V. G. Harris

"Copper and gold - based alloys having giant magnetoresistance properties were produced by melt spinning from arc melted and cast rods. The ribbon width varied between 1 and 2 mm and the ribbon thicknesses were in the range of 30 to 50 11m. The uniform microstructure of the cast rods indicated the composition homogeneity in the starting material. The ribbons showed composition uniformity across the cross section from EDX analysis. However, the spun ribbon microstructure changed from a 'frozen in' region near the wheel side to a nanosize spherically precipitated phase towards the freely frozen surface. The evolution of the microstructure from the spun ribbon state to the annealed ones was studied by optical microscopy, SEM and TEM. The structural information of the spun and annealed specimens was obtained from X - ray, electron diffraction, electron microscopy and ferromagnetic resonance. Magnetoresistance was measured by the four point probe method.IntroductionRecently. Giant Magnetoresistance. GMR. has been observed in sputtered thin films alloys of Ag. Au and Cu with Co and Fe [1. 2. 3]. The sputtered films are produced by condensation of the alloys from the vapor phase. These Ag. Au and Cu alloys are miscible and homogeneous in the vapor and liquid phase (except Ag alloys which exhibit phase separation even in the liquid phase) but immiscible and heterogeneous in the solid phase. In our work we have produced thin ribbons of the Cu and Au alloys about 30 µm thick from the miscible state in liquid phase by rapid solidification melt spinning. The microstructural development of the ribbons was investigated in the as - spun condition and on annealing. The other properties such as magnetization. GMR and Mossbauer Spectroscopy were also investigated in the various microstructural conditions of the ribbons."

Jan 1, 1994

By Ahmad Mahboubi

The damage caused by catastrophic earthquakes has always been an incentive towards more sophisticated building codes and requirements. In parallel to computer technology development, the engineers? attitude towards acquisition of more accurate results is increasing. This approach leads to designation of structural elements with more elaboration considering different aspects of their behavior. In addition, less simplified methods will be considered as satisfactory for analyzing such problems. The problem of soil-pile-structure interaction is one of the phenomena that can be included in this category. In general, there are two methods by which the study of soil-pile interaction phenomenon is studied. These include direct and sub-structuring methods. The sub-structuring approach relies on the linear or slightly non-linear behavior of soil since it employs the results of kinematic interaction analyses for inertial interaction studies. In the past, the kinematic interaction between pile-soil was considered as negligible. This was due to the softer nature of the surrounding soil that increased the time period of vibrations. However, more research revealed that although this approach was consistent in many cases, there were some sites where the time period decreased. This was due to the material properties of the foundation and the soil, in a way that caused the frequency of vibration meet natural frequency of the system. The second type of interaction is the inertial interaction which reflects the effect a structure on top exerts on the oscillation experienced by the foundation. This paper examines the impact of vertical load on the inertial interaction by virtue of impedance functions. Three different load cases for the structure at the top of a pile foundation were considered for the analyses conducted in this study. The changes in the stiffness and damping of the system by frequency are studied and finally, the results are presented.

Jan 1, 2010

By Jinjing Dua, Jun Zhua, Kuiren Liub, Bin Wang, Xiaolei Wua

V-Ti-Fe as hydrogen storage alloy was prepared by reducing metal oxides with a metallothermic reduction method. The deoxidation process of the V-Ti-Fe alloy was performed by electro-deoxidation and vacuum induction melting method, respectively. The results showed that the content of oxygen impurity can be controlled at about 0.2wt% after electrolyzing for 240min. Both the maximum values of hydrogen absorption capacity and the effective hydrogen desorption capacity are 2.65wt% and 1.01wt%, respectively. The deoxidization effect of vacuum induction melting process is more remarkable, with Ce as the reducing agent. It is found that Ce addition is beneficial for reducing the componential segregation, promoting the hydrogen absorption activation of V-Ti-Fe alloy. When m(Ce)/m(alloy) is up to 5%, the oxygen content has been reduced to 0.05wt% and the maximum hydrogen absorption capacity and the effective hydrogen desorption capacity are up to 3.36wt% and 1.85wt%, respectively.

Jan 1, 2015

By Long Meng, Yaodong Yi, Kuiyuan Chen, Zhancheng Guo, Yu Li

Blast furnace slag is the main by-product discharged in the iron and steel industry and contains considerable waste heat at dischargeing temperature between 1450 and 1550 °C. To fully utilize waste heat and slag, this study directly converted high temperature liquid Ti-bearing blast furnace slag into glass-ceramics via the “Petrurgic” method. Samples at different crystallization temperature were prepared and its influence on crystal phases, pore structure, and compressive strength were investigated via SEM, XRD techniques, and compressive strength measurements. Results showed that all glass-ceramic samples contained main crystals of perovskite, diopside and gehlenite and had a qualified mechanical performance with compressive strength above 100 Mpa, which meets the requirement of Chinese national standard for natural granite stone. With increasing crystallization temperature, pore size decreased, while the size of the perovskite phase firstly decreased and then increased with decreasing crystallization temperature. Samples had an optimum crystallization temperature of 1215 °C, maximum grain size and a densified structure with minimal pore defect.

Mar 1, 2018

By A. H. Geisler, F. Keller

Although the subject of precipitation from solid solution appears to be one of the more profitable fields in metallurgy for study with the electron Microscope, few comprehensive studies have yet been made. Occasionally electron micrographs have been published that illustrated alleged precipitation in various alloys, but frequently the apparent size, shape and distribution of the particles do not fully agree with those expected from theory or from observations of the Precipitate when the particles have grown to a size resolvable with the light microscope. The presence of a Widmanstatten pattern for submicroscopic precipitate particles has been demonstrated for only a few aged a1loys.l The initial problem has been the development of suitable techniques for applying the transmission-type instrument to a field that has been inherently associated with reflection-type microscopes. The various techniques have been the subjects of numerous publications, and instead of describing them individually here it will sufficc to say that the oxide film method has proved to be the most satisfactory method yet found for studying the microstructure of aluminum alloys with the electron microscope. This method has the definite characteristic advantage that the actual surface layer of the specimen is examined and not a plastic or silica replica. Doubtless suitable methods for forming and removing the oxide film could be developed for alloys of other metals. The purpose of this report is to point out the characteristics of the oxide film method that have been observed during the studies of numerous aged aluminum alloys and to present the results of these studies. Preparation OF Specimens The oxide film method for preparing specimens of aluminum alloys for examination in the electron microscope has been described in detail previously,¹,² Briefly, the procedure consists of preparing the metallographic specimen, forming the film by anodic oxidation and removing the film from the prepared surface of the oxidized specimen, The specimen is polished accordillg to the usual procedure for microscopic examination.³ he specimen may then be etched to remove flowed metal but etching to attack the alloy constituents or to leave them in relief as in the replica processes is not necessary. Electrolytic polishing is not generally recommended, Deep-etched specimens are used frequently, however, since they provide information that is not revealed by polished specimens and frequently present the same information more clearly than do the polished specimens, The surface preparation of specimens to be deep-etched is not important, since specimens that have been subjected to the first wet PoliShing operation are generally used, but frequently the as-rolled surface is Suitable. These specimens are then etched using a suitable macroetching reagent.

Jan 1, 1947

By J. F. Hazzard, R. J. Chalaturnyk, C. Khazaei

"Various measurement, monitoring and verification (MMV) techniques are used to ensure the safety of operations in petroleum projects. One of these techniques is microseismic (MS) monitoring of the caprock. A challenge in MS monitoring of caprock is that unlike projects such as tunnelling in hard rocks, the number of recorded events are much smaller and also wide spread through the rock mass which makes interpretation of the physical meaning behind the events very difficult.In this paper, a numerical technique is introduced and validated for coupling a finite difference code, FLAC3D (Fast Lagrangian Analysis of Continua), with a discrete element code, PFC3D (Particle Flow Code). Then, a similar approach is adopted for modeling microseismic events in the caprock. For this purpose, the underburden, reservoir and overburden layers are modeled by FLAC3D. A rather small section of caprock above the reservoir is nulled in the FLAC3D model and substituted by a PFC3D inclusion. The reservoir pressures are then applied to the reservoir section of FLAC3D. Once the FLAC3D cycles, there will be induced pressures in the caprock due to its undrained response to the change in pressures within the reservoir. These induced pressures are transferred to PFC3D as boundary velocities. Then the PFC3D cycles and sends back the boundary forces to FLAC3D. This back and forth process continues until equilibrium is reached. During this process, there will be bond breakages within the PFC3D inclusion that can be regarded as MS events. An algorithm for recording the microseismic energies based on a change in local strains is also implemented. The results are then compared with real data. The effect of injection fluid temperature is also studied. No significant appearance of microseismic events was observed due to injection of CO2 in both cases (i.e. with or without considering temperature). However, this continuum/discontinuum approach seems promising for understanding the microseismic response of caprock in more detail and also using the MS data for validation of geomechanical models."

Jan 1, 2015

By C. M. Haight

THE mine blacksmith and drill-steel sharpening shop at the Franklin mine of the New Jersey Zinc Co. is on the surface, adjoining the main shaft. It is a brick building, 51 by 30 ft. inside dimensions, with a corrugated iron roof and concrete floor. About two-thirds of the steels used are brought up through the main shaft; the remainder through two auxiliary shafts. The latter are carried to the shop by team or truck. At each shaft sufficiently large stocks of sharp drills of various types are kept to replace all the dull steels that may be sent up; while at the shop enough sharp drills are kept to replace the dull steels in. the stocks kept at the auxiliary shafts. Though this entails keeping a larger number of drill steels in service than might be required by other methods, there is less hurry in the sharpening shop and the steels have a longer period of rest. If a rest from use enables steel to recover from fatigue strains, this method secures that rest. The forms shown in Fig. 1 are supplied to each shift boss in books of 100. These are used to requisition sharp drills from the shaft stocks and enable the men at the tops of the shafts to sort out the required sizes and to have them ready to be sent to the various shaft stations. At one of the auxiliary shafts, the dull drills are placed on a platform from which they are dumped into the body of the wagon that takes them to the shop.

Jan 2, 1926

By Bunting HR

Developments since 1959 in major excavators to meet the high outputs of overburden and coal under the changing nature of the Morwell Coal Deposits of the Latrobe Valley are described. Particular reference is made to investigations of designs of the bucket wheel head configurations for the digging of flat batters on high faces, and examples are given of the wide use ofmodelsin these studies.An explanation is given of considerations leading to selection of the Long Boom or the Compact type of bucket wheel excavator for various applications. The past decade has seen increasing manufacture in Australia of components for excavators and similar machines. The measures undertaken to integrate these components with those from overseas (Germany) are described. A section of the paper deals with advances in Electrical Engineering for large excavators in Australia and its interdependenee with mechanical design and construction. Finally, as an example of the versatility of the bucket wheel excavator a description is given of a recent application for the mining of mineral sands in Northern N.S.W.

Jan 1, 1970

By Tom Dettweiler

Who We Are A global pioneer in discovery, development and recovery of deep-ocean assets Shipwrecks Deep-sea Minerals Company Overview Founded 1994 HQ ?Tampa, Florida USA Employees 45 Tampa + 150 Abroad Publicly Traded: NASDAQ:OMEX Requires Specific Financial Controls and Reporting

May 1, 2013

By Frank S. Palkovits

Over the past 30 years, underground paste backfill systems have been implemented across the globe in many configurations, each with a primary focus of providing high quality backfill to enhance mine operations. However, a number of key design drivers are not always well understood within design engineering firms that occasionally undertake this work, leaving opportunities on the table. Perhaps not always obvious to those newly embracing paste technology, identifying key drivers and opportunities attainable through a paste backfill system is generally not straightforward, requiring innovative approaches to securing higher productivity, availability, performance, maintainability, and operator health and safety. This paper describes a number of applications and audits of paste backfill systems for several challenging mine operations. Key challenges include iterative design aspects of availability of good backfill materials, plant location and configuration, general arrangement, and binder receiving/storage systems.

Oct 1, 2010

By F. Keller, A. H. Geisler

Although the subject of precipitation from solid solution appears to be one of the more profitable fields in metallurgy for study with the electron Microscope, few comprehensive studies have yet been made. Occasionally electron micrographs have been published that illustrated alleged precipitation in various alloys, but frequently the apparent size, shape and distribution of the particles do not fully agree with those expected from theory or from observations of the Precipitate when the particles have grown to a size resolvable with the light microscope. The presence of a Widmanstatten pattern for submicroscopic precipitate particles has been demonstrated for only a few aged a1loys.l The initial problem has been the development of suitable techniques for applying the transmission-type instrument to a field that has been inherently associated with reflection-type microscopes. The various techniques have been the subjects of numerous publications, and instead of describing them individually here it will sufficc to say that the oxide film method has proved to be the most satisfactory method yet found for studying the microstructure of aluminum alloys with the electron microscope. This method has the definite characteristic advantage that the actual surface layer of the specimen is examined and not a plastic or silica replica. Doubtless suitable methods for forming and removing the oxide film could be developed for alloys of other metals. The purpose of this report is to point out the characteristics of the oxide film method that have been observed during the studies of numerous aged aluminum alloys and to present the results of these studies. Preparation OF Specimens The oxide film method for preparing specimens of aluminum alloys for examination in the electron microscope has been described in detail previously,¹,² Briefly, the procedure consists of preparing the metallographic specimen, forming the film by anodic oxidation and removing the film from the prepared surface of the oxidized specimen, The specimen is polished accordillg to the usual procedure for microscopic examination.³ he specimen may then be etched to remove flowed metal but etching to attack the alloy constituents or to leave them in relief as in the replica processes is not necessary. Electrolytic polishing is not generally recommended, Deep-etched specimens are used frequently, however, since they provide information that is not revealed by polished specimens and frequently present the same information more clearly than do the polished specimens, The surface preparation of specimens to be deep-etched is not important, since specimens that have been subjected to the first wet PoliShing operation are generally used, but frequently the as-rolled surface is Suitable. These specimens are then etched using a suitable macroetching reagent.

Jan 1, 1947

By E. C. Lane

This report on properties of commercial motor fuels is the twelfth in a series made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the United States Department of the Interior. The first report contained data on motor gasolines sold during the winter of 1935-36.V The -present report, covering the summer of 1941, presents analytical data for 1,857 samples, representing the products of approximately 135 companies. As in previous surveys, these companies include both large and small suppliers. In addition, the Pacific coast is represented by data averaged by the Pacific Coast Technical Group before being submitted, and these data are published exactly as they were received. Conforming to previous surveys, the data cover three groups of samples -- regular-price, premium-price, and third-grade gasolines -- and each group has been aver aged separately. The number of samples, items, and brands comprising each group, exclusive of those of the Pacific coast, are as follows: Regular price, 1,010 samples, 291 items, and 86 brands; premium price, 577 samples, 263 items, and 78 brands; third-grade gasoline, 270 samples 159 items, and 74 brands. The meanings of these terms as used in the surveys are as follows: Sample: The individual supply of gasoline obtained at the filling station and analyzed in the laboratory.

Jan 1, 1942

By Edmund Davenport

THE specific aim of this work has been to study certain forms of internal deterioration which occur in tungsten filaments when subjected to high temperatures under various conditions, and to determine the cause of such deterioration. This would naturally lead to a consideration of methods of control or means of prevention of the phenomena. The deterioration was first noticed as a peculiar condition in the grain boundaries of certain tungsten filaments which had been burned? for long periods in lamps. In these cases it was noted that the grain boundaries contained a number of minute black dots which were at first thought to be non-metallic inclusions. It was demonstrated later that these dots or pits, as they were designated, could be readily produced by burning filaments in an atmosphere of flowing hydrogen. This method was convenient and adequate for the purpose, and was adopted for most of the work discussed in this paper. The evidence accumulated to date indicates that these pits are actually small voids between the grains. The purpose of this paper is to present- the information on this interesting subject gathered during a period of about 3 years. As applied to tungsten, the subject appears to be of considerable importance, experience having shown that this pitting ?is frequently associated with poor performance of filaments in lamps. The question has arisen as to whether these intergranular pits are peculiar to tungsten, or if they occur in all metals. If they are found iii all metals, the facts will be of considerable theoretical interest, as the material at the grain boundary plays an important part in most of the current theories of the properties of metals and alloys.

Jan 1, 1927

By C E. Loayza, R M. Pinto, J G. G=mez

The Yanacocha District is located 20 km north of the city of Cajamarca, in the Northern Andean Orogenic belt of northern Peru.Gold production may have occurred as early as Incan times (Paverd, 2000), but modern exploration that began in the 1960s targeted only copper and silver. Newmont Mining Corporation, BRGM and Compa±fa de Minas Buenaventura began exploring for gold in 1983, with Newmont as operator.Initial drilling took place in 1985. By 1992 a reserve of 1.28 million ounces was reported (Teal et al, 2002).Production began at the Carachugo deposit in 1993.Current reserves are 31.7 million ounces at $US 325 per ounce at a grade of 1.03 ppm (Newmont Annual Report, 2003).The operating company, Mineral Yanacocha SRL (Newmont 51 per cent, Buenaventura 44 per cent and International Finance Corporation five per cent) produced 2.85 million ounces in 2003, making Yanacocha one of the largest gold mining operations in the world. The district is made up of a series of epithermal, high sulfidation style gold deposits and one gold-rich gravel deposit (La Quinua), aligned in a NE trend.La Quinua is not discussed in detail in this paper. The bedrock deposits are hosted in a Miocene volcanic package, the Yanacocha Volcanic Complex that also trends NE.Re gional NW striking Andean faults intersect the NE striking Trans-Andean Chicama-Yanacocha structural corridor (Turner, 1997), localising the district mineralisation. These two structural orientations dominate the district, controlling breccia and intrusion locations, and gold mineralisation. Discontinuous EW oriented fracture zones are interpreted as extensional and locally are important in controlling gold mineralisation.

Jan 1, 2004

The North Saskatchewan River flows southwest to northeast through a 22-km-long valley in the City of Edmonton, supplying the drinking water to dozens of downstream communities. During heavy rains, combined sewers occasionally overflow into the river, which has a significant negative impact on the water quality and the sensitive environment. The West Edmonton Sanitary Sewer (WESS) W12, a syphon connecting the Rat Creek Trunk to the Gold Bar Wastewater Treatment Plant across the river, was designed and constructed to take the overflow to the wastewater treatment plant. Due to the complexity of the project, various 3D technologies were applied to facilitate decision-making processes. 3D models were developed for design review and design conflict detection, while 4D models were established to help create a robust construction schedule. Construction sequencing animation was used to convey design intents and demonstrate construction stages to contractors and workers. The combined applications of 3D technologies helped the project team to identify critical issues, and assured effective communication among engineers, management, contractors, and other parties. Therefore, it provided more opportunities for the success of the project.

Aug 1, 2013

By Richard A. Dick

In this report commercial blasting compounds are classified according to their nitroglycerin (or equivalent explosive oil) and ammonium nitrate content as dynamites, gelatins, blasting agents, military explosives, and blasting , accessories. The ingredients and more significant properties of each explosive are tabulated and briefly discussed. Data are summarized from various handbooks, textbooks, and manufacturers&apos; technical data sheets, together with the author&apos;s personal experience; however, this report is not intended to be a technical handbook, since it does not deal with blasting techniques. Instead, it seeks to acquaint the reader with the great variety of explosives, available, their advantages and disadvantages, and their general areas of application. Properties discussed are weight strength, cartridge strength, detonation velocity, density, detonation pressure, water resistance, and fume class. The weakness of the strength rating system and the importance of detonation pres- , sure, density, and detonation velocity in rating explosives are discussed. The terms "blasting agent" and "slurry," which are often misused, are defined. Trends indicate that blasting agents (that is, blasting mixtures with none of of the ingredients singly classified as an explosive), particularly high-density slurry blasting agents, will dominate the explosives field in the future.

Jan 1, 1968

By Henry M. Howe

(Cleveland Meeting, October, 1912.) Manuscript received Aug. 20, 1912. PROFESSOR RUFF&apos;S most illuminating paper&apos; describing his extremely valuable investigation of the carbon-iron equilibrium diagram assigns definite temperatures to certain very important lines in the diagram, viz.: the eutectic temperature EB (Fig. 1) and the " near-eutectic " temperature E&apos;B&apos;, but without indicating clearly enough the reasoning which warrants these assignments. These temperatures are of such primary importance that it is well to indicate the apparent gaps in the reasoning, in the hope that they may be filled in. In his diagram, Fig. 1, the point X and the lines B&apos;D&apos;HI represent the experimental results reached by Ruff and Goecke; 2 AB, AEB, and SE represent the liquidus, the solidus, and the solubility of the carbon in solid austenite in the absence of graphite according to Gutowsky,3 AB being also in accordance with Spiecker&apos;s data;4 ,S&apos;E&apos; the solubility of carbon in solid austenite in the presence of graphite according to Ruer and Iljin; 5 GS the line A3 after Goerens and Meyer;6 I and EBC the true eutectic line as inferred by Prof. Ruff from Gutowsky&apos;s data. B&apos;D&apos; is the carbon content found in cast-iron which had apparently saturated itself with carbon in the presence of the graphite of the enclosing graphite crucibles in which the determinations were made. From its straightness and its sharp inflection near 6.67 per cent. of carbon, the carbon content of * Professor of Metallurgy in Columbia University. 1 Metallurgie, vol. viii., pp. 456 to 464 and 497 to 508 (1911). 2 Idem, vol. viii., pp. 417 to 421 (1911). 3 Idem, vol. vi., pp. 731 to 743 (1909). 4 Idem, vol. vi., p. 524 (Wüst) (1909). 5 Idem, vol. viii., pp. 97 to 101 (1911). 6 Idem, vol. vii., pp. 307 to 312 (1910).

Nov 1, 1912