Search Documents

By S. D. Sanders

Goals of the Bureau of Mines include utilizing readily available minerals as substitutes for scarce mineral commodities and minimizing occupational hazards associated with mineral processing occupations. Therefore, the Tuscaloosa Research Center investigated using rapid-set cement as a suitable molding sand binder for small ferrous castings; currently petroleum-based binders are used. Substitution of a rapid-set cement would eliminate organic vapors associated with the petroleum-based binders; these vapors constitute occupational hazards and environmental pollutants. A binder containing 60 percent white portland cement (WPC) and 40 percent calcium aluminate (CA) would be an acceptable and economic substitute for petroleum-based binders where the foundry requirements are compatible with its limitations. It produced a set time and a pattern strip time of less than 1 hour. Cement, sand, and water mixtures developed compressive strengths from about 40 to 75 psi after 2 hours and from 120 to 130 psi after 24 hours. Tensile strengths of 18 to 22 psi were obtained after 2 hours, increasing to 30 to 35 psi after 24 hours. The addition of about 1 percent polyphosphate to the sand-cement-water mixture doubled the compressive strength and increased the tensile strength about 50 percent after 4 hours, but also increased the set time from 30 minutes to 1 to 1-1/2 hours. Po1yvinylacetate (PVA) resin latex additions resulted in rapid strength development. When castings were poured into the cement-bonded molds, the surface finish was fair to good on gray iron castings, but some areas of burn-on were present on steel castings. Using a graphite wash on the cement-bonded molds produced good surfaces on gray iron castings.

Jan 1, 1979

By James H. Harmon

As the trend to deeper mines, producing from marginal ore bodies, continues, mine hoists and their associated equipment will become more sophisticated, complex, large and expensive. Over the past two decades, mine hoisting equipment and systems have moved from steam engines to static rectification of ac to dc, and electronic controls are the standard. It is the intent of this section to present what is currently available in the field of mine hoisting equipment and systems. Because the present engineer has been exposed longer and more intensively to such things as computers, electronic devices, and machine design, no attempt has been made to make this a layman's article. Contributions from the electrical design and application engineer, gearing and hearing design engineers and other specialists have been incorporated. Some material will be devoted to electrical drive systems, rectifiers and gearing design among others. These items are inherent in the design of a mine hoisting system and the subsequent selection of the correct, most reliable and most economic system. The mine hoist can be a bottleneck between the underground mine and the surface mill. Correct selection of the right type of hoist is imperative. In this vital link between mine and mill, crude estimates of hoist capacity are not good enough, and the mining engineer must design and select the right hoisting system to meet the design specifications. 15.1-MINE HOIST TYPES There are two basic types of mine hoists available anywhere in the world today: the drum hoist on which the hoist rope is actually stored during the hoisting cycle, and the friction (Koepe), which merely passes the rope over the wheel during the hoisting process. Drum and friction hoists are "generic" terms which describe the two basic categories. Within each category are variations, as below. 15.1.1-DRUM HOISTS Drum hoists, as noted, actually store the hoist rope on the drum much the same as line on a fishing reel. To accomplish this task, the drums are so designed to store, in one or more layers, the footage of wire rope equal to the total maximum hoisting distance plus sufficient rope for cutting and inspection at regular intervals and for holding to the drum (see Fig. 15-1). Usual practice in hoist drum design is to allow three turns of hoist rope for holding on the drum and three turns for inspection cuttings. 1. Single-Drum Hoists-Fig. 15-2 shows a typical single-drum hoist as manufactured by most U.S. heavy-mining-equipment companies. With the exception of some very minor features, this design configuration is standard throughout the U.S.A. Fig. 15-3 is a plan view of a typical single-drum mine hoist. This particular hoist has a single-motor drive and a double-reduction set of gearing.

Jan 1, 1973

By S. V. Krusiewski, J. W. Gabelman

Regional metallogenic zones and areas of equal paragenetic range have been interpreted from a compiled metallogenic map. of Mexico. Mineralization gradients of the pattern subsequently identified extend inland from coastal zones of high-temperature mineralization, and join in a central longitudinal zone of relatively low-temperature mineralization, apparently leaving no zonal room for lowest temperature deposits. The striking regional zoning pattern can be correlated with regional deformation gradients of similar position and orientation. The gradients represent at least three major orogenic cycles in two structural belts. Paleozoic structural belts existed along each coast with deformation gradients diminishing inland toward a narrow, central peninsular craton. The Mesozoic-Tertiary Mexican (Cordilleran) belt covered the entire country with a gradient oriented toward the Gulf of Mexico. Most ore deposits in this belt are of Tertiary age, although Tertiary mineralization gradients seem to have "inherited" the pattern left by Paleozoic tectonic gradients. Mineralization gradients can be used to identify the regions most favorable for the occurrence of selected metals. A metallogenic province is characterized by particular proportions of various metals, and the relative proportions can vary from province to province; but within any province the same intensity of mineralization would produce similar deposits in different places. Declining intensity of minetalization produces different kinds and sizes of deposits in zones that are concentrically arranged around sites of strongest rock alteration. On a regional basis, districts of similar average intensity of mineralization occur in zones that generally parallel some tectonic grain with the result that tectonic deformation has been designated a principal cause of mineralization. Variations in the type and intensity of deformation would determine the type as well as size of metal deposits. Mexico is especially favorable for such a study be- cause of its great abundance and variety of epi-genetic mineral deposits in various lithologic, structural and tectonic environments. The concept is also useful in recognizing portions of Mexico favorable for the occurrence of specific metals. METALLOTECTONIC ZONING IN MEXICO Theory: In studies of individual districts and groups of districts throughout North and South America, areal zoning of metal deposits generally seemed to respond to the paragenetic sequence of iron, gold, copper, zinc, lead, silver, antimony and arsenic, gold and fluorite. However, the definition of district zones is greatly obscured by contemporaneous or rhythmic deposition of metals, especially in the middle of the paragenetic range, and by the common superimposi-tions of different generations of metals. Zones could usually be distinguished only for groups of metals, such as early precious metals, base-metal sulfides, sulfosalts and late precious metals. The best defined zoning in a district is normally the spatial separation of the greatest volumes of altered and metallized rocks.' Exceptions are districts representing the high- and low-temperature extremes of the mineralization range where the former creates a matrix for the latter. In most districts the total quantity of alteration products is greatly in excess of, and appears to be roughly proportional to, the total quantity of metallization products. Subsequent to the bicomponent nature of each district, the most important mineralogical feature is the great excess of one to several metals or minerals which results in a district identifiable as one of predominantly gold, copper, lead-zinc, fluorite, etc., although a great variety of other elements may be present. The para-genetic range for the abundant elements in any district is only a portion of the entire possible range for all the elements representing the complete process throughout the region. Early during investigations of this type, it became apparent that the consistent bicomponent character of districts allows two methods for studying epi-genetic mineralization patterns. One is to identify and plot altered rock "pipes,"* which are easily recognizable in the landscape by their anomalous

Jan 1, 1969

By D. F. Hewitt

Page Introduction..............................305 Geologic features of eastern Oregon....................306 Geology of the Sumpter quadrangle....................306 Rocks older than the ore deposits...................307 Rocks younger than the ore deposits.............. . Lodes of the Sumpter quadrangle..................312 Areal distribution.......................312 Geologic distribution.................... . Major features of the veins...................313 Mineralogy and texture of the veins.............. . Ore deposits zonally disposed around the Bald Mountain batholith . 317 Summary of mineralogy and texture.............336 Zonal relations......................337 Ore deposits zonally disposed around Greenhorn Mountain batholith. 340 Zonal relations..................... . Relation of textural features to zonal arrangement of veins.....341 Summary of zonal relations.................. . Comparison with similar districts................. . Outlook for the district......................344 Introduction In an earlier report on the Sumpter quadrangle1 it was briefly stated that the quartz lodes of that region might be separated into several groups or belts on the basis of the kind and abundance of the minerals of which they are composed, and that these belts were disposed as areal zones around the principal intrusive mass of the region. When the opportunity to revisit the region was offered in 1929, as a result of a cooperative agreement between the State Mining Board of Oregon and the United States Geological Survey, it seemed advisable to pay particular attention to this feature of the lodes, in the hope that if the idea of zonal relations was confirmed it might serve as a guide in exploitation.

Jan 1, 1931

The Pike River Coalfield is located on the West Coast of the South Island of New Zealand near the top of the Paparoa Range approximately 45 km north east of the coastal town of Greymouth. The Pike River Coal Company Ltd (PRCC) is owned jointly by New Zealand Oil & Gas Limited (NZOG) and private investors.   The project has followed a long and difficult road towards project implementation which is now a reality with mine construction scheduled to commence in November 2005. The first stage of the project, the consent and land access process has been the most difficult. Resource consents for the project were first applied for, granted and appealed in 1998. A second round of modified resources consents followed a similar path in 2001. Following consultation with a range of parties including local and central government as well as the Department of Conservation, in March 2004 the Minister of Conservation granted PRCC access through Department of Conservation land. In October 2004, the Environment Court issued a Memorandum of Consent granting resource consents with conditions that had been negotiated between PRCC and the appellants.   The second stage of the project, investigation and design, commenced in December 2004 and was completed in June 2005 with the PRCC board ratifying the project capital and operating budgets. While the investigation and design work was proceeding, PRCC were also engaged in securing private equity and bank debt funding for the project. Formal Board approval to proceed with project construction was granted in September 2005 following completion of fund raising.   The project consists of a number of significant construction activities, namely: +        10.5 km of mine access road through previous logged and virgin rain forest; +        2.2 km of tunnel through metamorphic rock; +        a coal preparation plant about 8.3 km from the mine portal; +        an underground coal preparation plant; and +        a major slurry pump station, high and low pressure underground water supply systems to support hydraulic mining units and underground coal transport respectively.   Project construction is expected to be completed in April 2007 with completion of the ventilation shaft. Mine production will commence in December 2006 with coal from pit bottom development which will be carried out by the mine owner.

Jan 1, 2005

By V. D. Perry

Mineralized breccia pipes, because of their widespread occurrence and close structural relations to some of the world's great ore bodies, are objects of unusual interest for mining engineers and geologists. The literature contains many references to them, but it is questionable whether their genetic significance and economic importance have been sufficiently emphasized. The purpose here is to stress these features, relating them to the field facts, for the particular benefit of younger generations of geologists who, confronted with and sometimes confused by the growing flood of geochemical, geophysical, and other specialized research approaches, may be reassured that mappable field relations remain a foremost guide to a better understanding of ore deposits. A mineralized breccia pipe is a pre-mineral, breccia structure which has controlled the circulation and deposition of subsequently introduced mineralization. It is composed of relatively rotated angular or rounded rock fragments, set in a mineralized matrix. A pipe in plan outline may be circular, oval or approach polygonal form, with a steep to vertical axis proportionately much greater than its horizontal dimensions. The pipe is a steeply plunging, chimneylike mass of brecciated rock cemented with later minerals. Rock breaks in a variety of ways and complete fragmentation often occurs without rotation of individual pieces. A finely broken rock mass may fit into a tight jig-saw pattern, each fragment having mutually concordant boundaries with its neighbors. The result is a stockwork of innumerable reticulating cracks that, once cemented by mineralization, forms a complicated intersecting network of individually insignificant but collectively important seams and veinlets. Stockwork fracturing among its many forms takes the shape of domes of subsidence, fracture pipes, and related peripheral zones around and over breccia columns, or a combination of any of these structures. The significance of the mineralized breccia pipe is that it represents the extreme or climactic expression of a structural type which has a variety of mutations including subsidence domes, fracture pipes, and other stockwork zones all with related ancestry and similar to dissimilar characteristics. These allied and associated structures hold an answer to the fundamental question of the origin of many important ore deposits. CANANEA-TYPE LOCALITY FOR BRECCIA PIPES The Cananea district is characterized by an unusual development of mineralized breccia pipes. It is an important copper producer located in Sonora, Mexico, a short distance southwest of Bisbee, Arizona, and at the southerly limit of the great porphyry copper belt of the southwestern U.S. Cananea's rocks consist of Paleozoic quartzite and limestone capped unconformably by a thick series of volcanics including andesitic flows, tuffs, and agglomerates. These rocks have been intruded by a deep-seated granite with related basic and acid differentiates including dikes and plugs of quartz mon-zonite porphyry. Mineralization coincides with a northwesterly trending belt of these intrusives which break upward into and through the sedimentary-volcanic rock sequence. The district has weakly defined tectonic alignments in a northwesterly direction with subordinate intersecting fracture elements, but lacks important faulting or fissuring to provide throughgoing avenues for the upward circulation of mineralizing fluids. Thus, as will be discussed in subsequent paragraphs, the alternate way in which late magmatic and hydro-thermal derivatives of the parent magma reached the near-surface zone was by excavating their own breccia pipe channelways. There are numerous stages of breccia pipe development, related both in time and space to magmatic activity. A compilation of similarities and differences in various pipes suggests that proximity or remoteness of a demonstrable or inferred magmatic source provides an orderly genetic basis for describing the following representative types. Cananea Duluth Type: There are no intrusive rocks within or close to the Cananea Duluth pipe; therefore, the existence of any deep-seated magma that may have been related to its formation must be inferred. The structure is an oval-shaped ring 1200 x 300 ft in plan dimensions, cutting steeply across low angle, bedded tuffs, and other volcanics; it has been developed by drill holes to a depth of 2000 ft below the surface. The ore follows the periphery of the pipe and is composed of intensely brecciated rock which is cemented by minor galena, sphalerite, chalcopyrite, quartz, carbonates, and adularia. There is a definite vertical zoning of sulfides with less galena, continuing sphalerite, and increasing chalcopyrite at deeper levels. Within the interior of the ore ring, the brecciation becomes progressively weaker and coarser, the whole indicating relatively gentle slumping with broken, thin tuff beds pre-

Jan 1, 1961

By N. J. Grant, B. C. Giessen, M. Morris

The slvuclures of alloys in the system In-Bi have been investigated after (levy vapid queuching from the mell (splat cooling) to -190°C. Tuo-phase fields could be suppressed over most of the tota1 concentvalion range; five melastable phases a1, a2, ?, ?1. and ß exisl, of which four have simple elementtike structures. For example, ß has the A5 struclure of white till. Crystal-tographic data and coordination numbers for these phases aye given, as well as addilional information on the equilibrium diagram, where a new phase In5Bi3 teas found. THE phase diagrams of binary combinations of B elements from the groups B2, B3, B4, and B5 are usually of a simple type and show considerably fewer intermediate phases than combinations of these elements with A metals, transition metals, or the B1 noble metals. Aside from phases such as the typical B3-B5 compounds with the ZnS-B3 structure type, few stoichiometric phases are known; among them are In2Bi and 1nBi.l Nonstoichiometric phases include ß (In-Sn), a1, (In-Pb), and the tin-rich ? phases in the In-Sn, Cd-Sn, and Hg-Sn systems.' The first two phases have a close relationship to indium, while the latter group are known to be structurally related to a Sn. Thus, there are generally no immediate experimental data for the correlation of the crystal structures of B metals and B metal combinations with certain monotonously varying parameters, such as the valence electron concentration (VEC), or the average atomic size. Such parameters have been recognized as structure determining, e.g., for the transition 4 Sn — y phase,2,3 where nonintegral valence electron concentrations are encountered. It should be possible to extend such correlations to other binary systems, if nonequilibrium single-phase alloys could be produced over broad valence electron concentration ranges, and if their crystal structures could be regarded as being imposed by their electronic states. It has been shown in the case of the tin-rich 7 phases3 that alloy phases with typical crystal structures can be produced in B metal alloys rapidly quenched from the liquid to -190°C by the splat cooling technique due to Duwez,3-8 and reviewed in Refs. 5 and 6. The In-Bi system was selected because it extends over a valence electron concentration range in which several metastable, nonstoichiometrir phases could be expected to occur. Further, the low melting points of the known intermediate phases, In2Bi and InBi, Fig. 1(a), indicated low binding energies and thus possibly low driving forces for the formation Of the equilibrium structures. EXPERIMENTAL TECHNIQUES AND RESULTS The preparation of the quenched foils followed the practice described in Ref. 3. Master alloys were produced by melting of indium (99.97+) and bismuth (99.99+) in evacuated Vycor capsules or in an inert gas arc furnace; quantities of 20 mg were splat-cooled onto copper and silver substrates held at - 190°C; and crystal structures and lattice parameters were determined on a GE XRD-5 diffractometer using Cu Ka, radiation at -190°C and at room temperature. The duplication of each run with both substrates permitted the elimination of overlap of the substrate diffraction pattern and that of the investigated substance. The XRD patterns were usually taken from sin2 " = 0.03 to 0.35; the substrate was used as a means of internal calibration. The fractional accuracy of the lattice parameters of metastable phases is approximately 10-3 In the following, all percentages are in atomic percent. The stable and metastable phases found after rapid quenching to -190°C are listed in Table I, together with estimated concentration ranges and crystallographic data. The investigated alloys and phases present in them are given in Table 11. Except for the region between indium with 33 and 50 pct Bi, where a revision of the equilibrium phase diagram became necessary to include a new stoichiometric phase In5Bi3, the diffraction patterns taken after heating to room temperature agreed with those expected from the phase diagram, Fig. l(a). This suggests that the new nonstoichiometric phases are not stable at room temperature, thus following the observations made for the y phases based on tin.3 Results concerning the equilibrium phases In2Bi and In5Bi3 and the revision of the equilibrium phase diagram which is made necessary by the inclusion of In5Bi3 will be treated first. The Crystal Structure of In2Bi. Makarov7 had identified In2Bi as belonging to the AlB2-C32 type ; however, in a later paper the structure was revised.8 In2Bio was found to be of the Ni21n-B8ß type,21 with a = 5.496A, c = 6.57.9A, and N = 6 atoms per unit cell.9 This crystal structure was confirmed in the present work; definite evidence for the doubling of the c axis, as compared to the A1B2-C32 type, and for the proposed order structure, was found in the powder pattern. The observed lattice parameters agree well with those of Ref. 8; those measured at -190°C are given- in Table I. The Crystal Structure of In5Bi3. A new, equilibrium, intermediate phase was identified in slow-cooled, as-cast alloys; it was identified as In5Bi3. The structure has been worked out by Giessen and Grant;" lattice parameters at -190°C are given in Table I. This phase is probably identical with "In3Bi2", produced by vapor deposition techniques, but not recognized as an equilibrium phase by Palatnik et a1.11 After completion of the present work, the existence of In5Bi3 has also been demonstrated by superconductivity measurements on In-Bi alloys.20

Jan 1, 1968

Jan 1, 1951

By Thomas E. Howard

Engineers today face a tremendous challenge. Growing population and rising standards of living all over the world are creating unprecedented and accelerating demands on and for all kinds of technology. At the same time, the public is becoming more and more conscious of--and concerned with--the impact of technology on human welfare. The growing controversy over the Supersonic Transport is a case in point, It is clear that the modern engineer must expect to spend a growing share of his time considering this dilemma and evaluating the tools that are available to him, not only with respect to their adequacy for the job at hand but also their capability for meeting the increasingly demanding--and, in many cases, conflicting--requirements of the future. This meeting seems a particularly appropriate place to speculate about the future of mining technology. The summary of the state-of-the-art in surface mining contained in the papers scheduled for the International Conference, together with the recently published Surface Mining volume, constitute not only a major contribution to the technical literature but also form an impressive record of technologic progress. That record, and the advanced technology displayed in the exhibits, and to be discussed in the SME technical sessions demonstrate engineering achievement in which the mining community can justly take pride.

Jan 1, 1968

By W. E. Dennis, M. M. Fine

"INTRODUCTION During peacetime, the United States uses less than 3,000 tons of chemical-grade celestite annually. The war need, however, was estimated to exceed 15,000 tons a year.Hitherto; most of the required chemical-grade ore has been imported from England, Mexico, and other foreign countries. If foreign sources do not find it possible to meet the demand for ore of chemical grade (plus 92 percent SrSO4), it is expected that requirements could be satisfied by concentrating low-grade domestic ores. Celestite deposits on Brown, Nolan, Fisher, and Coke Counties, Texas, are considered to be possible sources of supply for this low-grade material. The Bureau of Mines explored the most important deposits to determine the grade and amount of ore available and conducted ore-dressing tests to obtain a suitable method of concentration.The exploratory work, consisting of test pitting and sampling, was carried on under the direction of W. E. Dennis, one of the authors of this paper, from October 8, 1942, to January 30, 1943. The ore dressing-tests described herein were conducted at the Bureau of Mines Laboratory at Rolla Mo.In this report, a particular deposit is referred to by the name of the landowner on whose .property the .deposit lies. The location of the deposits investigated is shown on figures 1, 2, 3, and 4.The celestite deposits were previously studied by the Bureau of Economic Geology of the University of Texas, and the results of its investigation are published in Mineral Survey Circular No. 46."

Feb 1, 1947

By R. A. Cummings

From before the turn of the century until as recently as the 1950s, relatively shallow coal reserves near the margins of the Illinois Basin were extracted by room- and pillar methods. Subsequent development has, in many cases, extended onto ground with high subsidence potential. The same state of affairs exists in many other historical coal mining districts, as well as in Illinois. Pit subsidence in Illinois is particularly common in the towns of Streator, Carterville, and Herrin, although there are others. Pit subsidence is characterized by distinct circular or oval depressions and normally is associated with shallow mining and thick soil relative to the thickness of rock.

Jan 1, 1985

By Takeo Oki

A new suspension electrolysis method has been developed, which enables without any gas or dust pollutants a direct anodic extraction of zinc from zinc sulfide concentrates, while simultaneously oxidizing sulfide sulfur to elemental sulfur. The investigations were performed in a laboratory scale electrolytic cell with suspended zinc sulfide concentrate particles with or without graphite powder additions in dilute sulfuric acid electrolyte. By regulating the redox potential of the electrolysis system in combination with some additions, for example [Fe3+/Fe2+, MnO 4/MnO2, MnO 2/Mn2+ or MnO 4/Mn2+], the anodic dissolution reaction of zinc sulfide has been accomplished effectively without evolution of hydrogen sulfide. Under optimum conditions the anodic current efficiency of zinc dissolution ammounted up to 95 %, while sulfide sulfur was converted nearly completly to the elemental form. Purification by removal of sulfur and other impurities gives a zinc sulfate solution suitable for electrolysis to cathode zinc.

Jan 1, 1975

By Yao Dun-Pu

Solution mining, sometimes also refered to as chemical mining or bacterial mining, is an innovative technology which, by making use of proper chemical reagents and taking advantage of bio-chemical action of some micro-organism species, can dissolve effectively most. desirable metallic values from ores and then extract them profitably from the resultant metal-bearing solution by suitable means to form the metal product it is more preferable to the conventional mining methods, not only because of its capability to improve working conditions and minimize environmental problems either underground or on surface, but also for its amenability in particular, to exploit low-grade or submarginal ore bodies, or those deposits which are too deep-seated to be mined out economically. Furthermore, it also provides a potential approach to win metals directly from their ores or ore-deposits in-situ by more simplified methods and at a lower cast than the conventional mining-milling-smelting process would do previously. Hence, in developing countries such as China, it will most, probably become a new mining tool of great promise. (1)

Jan 1, 1981

By Charles J. Johnson

The United States is totally dependent on imports for all primary chromite and most ferrochrome supplies. Although the United States imports chromite and ferrochrome from a number of countries, the long-term future of chromite supplies appears to lie in southern Africa (Republic of South Africa and Zimbabwe) where 88 percent of known world reserves exist. Floreover, low mining costs and the availability of low-cost electricity for ferrochrome production gives South Africa a comparative advantage over most other chromite and ferrochrome-producing nations. A well-known problem faced by the United States is that when viewed from a longer-term perspective, the major sources of supply of metallurgical grade chromite and ferrochrome may be subject to disruption. The three countries that have caused the greatest concern have been the Republic of South Africa, the Soviet Union, and Zimbabwe. South Africa presents a particularly difficult problem because it may be subject to internal political unrest and/or U. N, economic sanctions. South Africa has increased its share of world chromium production from about 30 percent in 1968 to 62 percent in 1978.1

Jan 1, 1982

By D. A. Beattie

Three novel dextrin polymers of varying functional group chemistry but similar molecular weight have been used to depress talc in single and mixed mineral studies. The mixed mineral system was a model sulphide ore consisting of talc, pentlandite, and chalcopyrite. Adsorption isotherms for the three polymers on both valuable and gangue mineral phases were determined to give initial clues as to the ability of the polymers to depress talc. Flotation testing revealed a distinct hierarchy of effectiveness of the polymers in the depression of talc in the single mineral system (MP Dextrin > CM Dextrin > Dextrin TYM), reflecting the observed adsorption affinity and adsorbed amount of the polymers on talc. However, a different order of effectiveness was observed for talc depression in the mixed mineral system (CM Dextrin > MP Dextrin > Dextrin TYM). Competition between the valuable and gangue mineral phases for uptake of MP Dextrin is responsible for its observed decrease in efficiency in mixed mineral flotation. All three polymers were found to be reasonably selective in their action, although at high dosages the polymers began to affect the flotation of the valuable minerals.

Jan 1, 2006

By L. Valentik

Many attempts have been made during the last forty years to evaluate the performance of gravity separation equipment, that is, the effectiveness with which light and heavy particles are separated. The most comprehensive treatment of the subject was made at the 1st International Conference on Coal Preparation held in Paris (1950) by Cerchar. The methods suggested by the Conference were accepted and very widely used in the last 25 years. This paper discusses an improved method of evaluation in the light of the now accepted standard presentation. The float and sink analysis of the product is presented on a Gaussian distribution curve, resulting in an easier visualization of the inherent difficulties of separation. The ogives of the distribution curve are then plotted, giving a quantitative measure of the deviation from perfect separation as an error distance instead of an error area. Illustrations of the new method are given both for gravel and for coal preparation, but the concept is valid and applicable to other types of minerals which are separated by gravity methods.

Jan 1, 1968

By E. L. Smith

The development of larger size flotation machines, which started in the 1950's and 1960's, is still proceeding. The largest mechanical flotation machines avail-able today have unit volumes in the range of 38.2 to 43.9 M3 (1,350 to 1,550 cft). Designs for mechanical flotation cells of unit volumes as large as 70.8 m3 (2500 cft) are available. The development of these "giant" flotation machines has been and continues to be motivated by the increasingly critical forces of higher energy and capital costs, decreasing ore grades, and lower (real) prices for the products. As an expansion of a previous publication, this paper reports the further development of an improved mechanism for these large flotation machines. The starting point in the develop¬ment of a new mechanism was the identification of design and performance features of existing machines where improvements were desirable. The result of this work was a mechanism which s is an improvement over existing designs. This new design is characterized by an efficient overhung stator and a vortex profile rotor. The overhung design of the stator removes unnecessary and undesirable baffling in the lowest parts of the tank, while maintaining a quiescent froth layer. This results in lower power consumption and better pulp circulation and solids suspension. The vortex profile rotor acts as an efficient pump, with higher pulp recirculation rates as evidenced by the increased air dispersion capabilities, good solids suspension, and low power consumption.

Jan 1, 1983

By Bruno KERL

THE list of deaths reported during the year 1905 comprises the following names (the figures in parentheses indicating the year in which the persons named were elected to membership:- Honorary Member.-Dr. Bruno Kerl. Members and Associates.-Charles Christy Adams (1903), John Wesley Anderson (1898), William Burton Barber (1901), Thomas A. Bennett (1900), Luke W. Bryan (1901), Edwin S. Daugherty (1905), William Scott de Camp (1875), George H. Eldridge (1889), B. W. Frazier (1871), John Broome Guinn, Jr. (1897), Dana C. Irish (1900), Harry Hugh Lee (1899), William Alfred Lindsay (1902), Roland C. Luther (1884), James MacNaughton (1890), Gordon McLean (1899), Herbert Holmes McNamara (1902), August R. Meyer (1886), William Orr (1897), William J. Parker, Jr. (1898), Joseph Phillips, Jr. (1895), Charles O. Ripley (1902), Emmerich J. Schmitz (1883), Ludwig Philip Seeger (1900), Jacob Johnston Sperry (1900), Gustavus H. Stoiber (1902), William L. Study (1905), Robert Macnair Wilson Swan (1900), Richard Henry Terhune (1886), Joseph Thiry (1892), John N. Tisdale (1903), Alfred Isham Totten (1897), Walter H. Virgoe (1902), Charles H. Wellman (1890), Harvey L. Williams (1903). Of these, Dr. Bruno Kerl and Prof. B. W. Frazier have been made the subjects of special Biographical Notices in the Bi-Monthly Bulletin 1 the former in No. 4, July, 1905, p. 743, and the latter in No. 5, September, 1905, p. 1097. Concerning the remainder of the list, the following paragraphs comprise such information as could be obtained by the Secretary. Charles Christy Adams, who had been a member of the Institute since 1903, died in Johannesburg, South Africa, August 31. 1905. He was born in New York City, July 13, 1849, and received his technical training at the Colorado State School of

May 1, 1906

By S. K. Ash

In arriving at economic losses in coal mining due to accidents, a statistician is confronted with many difficulties on account of the lack of information relative to nonfatal accidents. For comparative purposes the ex¬ perience of those countries, States, or companies that keep complete records can be drawn upon and an extimate can be arrived at whereby one State can be compared with another, or one mine compared with another in the same district. Such a comparison for the United States has been compiled by the United States Bureau of Mines. It will be observed in Table 1 that the cost per ton for accidents in the State of Washington for the year 1927 is higher than for any other State, with the exception of Georgia and North Carolina, with a small combined tonnage of 130,089 tons. (The figures for coal production in Table 1 are taken from Bulletin 319, 1930, of the United States Bureau of Mines.) The reasons why the cost of accidents in Washington might be higher than the average are on account of physical conditions such as steep pitches, faults, igneous intrusions, highly explosive coal-dust, extremely friable coals, presence of gravel and water, very gassy coal beds, rugged topographic conditions, inherently bad roof and floor, thick beds, and heavy cover. The nature of the coal beds requires the use of preparation machinery. The mines are often deep, and topographic conditions are such that long and fast haul¬ age becomes necessary. All of these factors not only tend to cause high cost of production, which is manifested largely in a. lower than average daily pro¬ duction, per man, but..they.also affect to some degree a tendency toward a higher than average cost for accidents.

Nov 1, 1931

By R. Hogg, S. Chander

"An overview of various physical and interfacial characterization methods for use in mineral processing is presented in this paper. The availability of a large number of characterization techniques and commercial instruments requires that the reliability and limitation of each be carefully examined. The choice of a method may depend upon the manner in which the information is to be used, for example in development of new processes, plant and process design, plant control, problem solving, etc. IntroductionThe behavior of particulate systems, in mineral processing and other applications, is primarily affected by the physical characteristics (size, shape, surface area, pore structure) of the particles and the nature of the different solid-fluid interfaces present. Mineral processing operations in general are either designed to modify and/or control physical and interfacial properties (grinding, classification, agglomeration, etc.) or are strongly influenced by them (flotation, flocculation, solid/liquid separation, etc.). Characterization of physical and interfacial properties should be an integral part of the development of new processes, plant and process design, and routine plant operation.Our purpose in preparing this article has been to present an overview of the current status of characterization, to point out areas of weakness, and to discuss the reliability and limitations of the various techniques, procedures, and instrumentation available. For more detailed discussion of methods, etc., the reader is referred to standard references.Sampling particulate solids.Sampling is a critical factor in any procedure for characterizing particulate materials — the reliability of characterization data is ultimately limited by the extent to which the sample used was truly represen¬tative of the population from which it was taken.Sampling from particulate solids involves two basic problems: (1) the selection of a random', unbiased sample and (2) choice of the appropriate sample size.The problem of sample selection involves the design of a sample collection procedure that ensures that every kind of particle in the population has the proper chance of being included in the sample without bias. Specific procedures such as the well-known cone-and-quarter technique have been developed and are discussed at length in the literature on particle characterization (Allen, 1981: Herdan, 1960: Gy, 1982)."

Jan 1, 1989