Search Documents

By G S. Esterhuizen, M M. Murphy, T S. Bajpayee

The strength reduction method (SRM) has been implemented in the FLAC3D finite difference software and applied to coalmine entry support evaluations. The FLAC3D numerical models have been calibrated against instrumented field sites in varying geologies, depths and field stress conditions. The calibration between the field and model results obtained a satisfactory match for rock deformation and support response. Previous research has also developed good correlations between numerical model stability estimations using the SRM and empirically derived stability estimations using the analysis of roof bolt systems (ARBS) software and the coalmine roof rating (CMRR). The purpose of this paper is to further apply the SRM to investigate how specific geotechnical and support parameters can impact coalmine entry stability. Results from different studies demonstrate how the calibrated models were used to investigate a few of the well-known questions in both mine design and support design. For mine design the impact of strong and weak beds in the roof strata, rotating the principal stresses and weakening the floor on excavation stability is investigated. For support design the impact of support length, support spacing and adding cable bolts to the design is demonstrated. These scenarios are evaluated in developmental coalmine entries for a variety of geology and field stress conditions. Stability factors are calculated for each scenario using the SRM. The SRM allows the impact of each parameter to be quantified and allows the support system to be optimised for given geotechnical conditions.CITATION:Esterhuizen, G S, Murphy, M M and Bajpayee, T S, 2014. Analysis of geotechnical and support parameters on coalmine entry stability using the strength reduction method, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 383–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By W. L. Price

Recent publication of United States Bureau of Mines figures showed that the sand and gravel (3) industry is the largest single mining industry in the United States in term of yearly tonnage produced. The yearly production of over 500,000,000 tons per year now exceed bituminous coal production. This disclosure caught unawares many observers who have not been following closely the rapid-growth of this phase of mining. Along with this steady growth in production, the sand and gravel industry has gone through an accelerated and varied program of beneficiation in a period of the last ten years.

Jan 1, 1958

Maps To Accompany Bulletin 418

Jan 1, 1941

By H. W. St. Clair

This study was undertaken to provide a more adequate knowledge of the chemistry of the sulfide volatilization process for recovery of tin from low-grade Bolivian ores. The investigation was partly supported by the Department of State under its program for scientific cooperation with South American republics. The results of this investigation demonstrate the conditions under which cassiterite (Sn02) may be converted to stannous sulfide by reaction with pyrite or sulfur vapor, Quantitative data are given on the rate of sulfidization and on the vapor pressure of stannous sulfide.

Jan 1, 1954

By G. J. Simandl

"Since the 1980s, China has become the predominant producer of REEs. Recently, it introduced REE export quotas and this started a world-scale REE exploration rush. REE resources are concentrated in carbonatite-related deposits, peralkaline igneous rocks, pegmatites, REE ± P veins, ion adsorption clays, placers, and some deep ocean sediments. REEs could also be derived as a by-product of phosphate fertilizer, U processing, Ti-Zr-bearing placers, and exploitation of Olympic Dam-type sub-type of IOCG deposits. The ideal REE development target would be located in a politically stable jurisdiction such as Canada. REE grade and tonnage, mineralogy, and permissive metallurgy are some of the key technical factors that could be used to screen projects. INTRODUCTIONAccording to the International Union of Pure and Applied Chemistry (IUPAC), the term “rare earth elements” (REEs) encompasses yttrium (Y), scandium (Sc), and the lanthanide series: lanthanum (La), cerium (Ce), praseodymium (Pr), neodymium (Nd), promethium (Pm), samarium (Sm), europium (Eu), gadolinium (Gd), terbium (Tb), dysprosium (Dy), holmium (Ho), erbium (Er), thulium (Tm), ytterbium (Yb), and lutetium (Lu). This definition is used throughout this paper.REEs are subdivided into light (LREE) and heavy (HREE) categories. LREEs include, Sc, La, Ce, Pr, Nd, Sm, Eu, and Gd and HREE include Tb, Dy, Ho, Er, Tm, Yb, Lu, and Y. Promethium (Pm) does not occur in nature. Concentrations of individual LREEs in the upper crust of the Earth are comparable to those of base metals. Even the least abundant REE (Lu) is about 200 times more abundant than gold.The production of REEs, reported in the form of oxides (REOs), for 2011 is estimated at 140 000 t (Figure 1a). Although high technology industries can substitute several REEs with other materials, these substitutes are typically more expensive or less effective than the REEs they replace. A number of countries, including the United States, consider several REEs essential for national security, their economy, and a general reduction in green house gas emissions. The forecasted demand for individual LREOs is much higher than that of HREOs (Figure 2). Dy, Eu, Tb, Nd, and Y are essential for the US economy and subject to predicted supply disruptions (U.S. Department of Energy, 2010)."

Jan 1, 2012

By James S. Falcone

Soluble sodium silicate materials have well known applications in flotation for desliming, selective depression and corrosion control. Recent advances in the understanding of the complex polymeric nature of silicate solutions using NMR spectroscopy, combined with our studies of the effects of polymeric silicate anions on metal ion activities in solution, oxide mineral surface charges and surfactant adsorption on clays are related to beneficiation processes. The results of these studies indicate the sodium silicates can be used to cause a solution chemistry and particle surface charge characteristics favorable to enhanced effectiveness in typical ore beneficiation systems.

Jan 1, 1981

By B. T. Lusk, Q. Q. Huang, R. Q. Honaker, K. A. Perry

Rock dust is applied in underground coal mines to prevent the propagation of coal dust explosions. It is applied either dry or wet. Both methods have advantages and disadvantages, but the formation of caked rock dust particles is cited as a significant concern for wet applications. We conducted a study to evaluate the effect of modifying the rock dust particle surfaces to repel water and each other by the addition of oleic acid and sodium oleate. At a sodium oleate dosage of 1 kg/t, a contact angle of 112o was measured, indicating strong surface hydrophobicity and thus the ability to repel water. Fourier transform infrared spectroscopy (FTIR) studies indicated a chemisorption mechanism, which is necessary for long-term stability of the surface modification. The dispersibility of the modified rock dust samples was elevated by the application of both oleic acid and sodium oleate, thereby indicating a significant reduction or elimination of the detrimental effect of caking. Tests in an explosion chamber showed an 82.8 percent reduction in the dust explosion potential relative to untreated rock test applied by the wet technique.

Jan 1, 2015

By M. Ataei, F. Sereshki, R. N. Masir

Given the inherent risks and disruptions in underground coal mining operations, strengthening the resilience of critical infrastructure has become a vital priority. This paper aims to evaluate the resilience of the underground coal mining environment using historical data and expert judgment. The study serves as a framework for optimising the utilisation of critical infrastructure to minimise operational disturbances. To achieve this, a practical methodology has been developed, incorporating nearly two and a half years of collected operational data, a hierarchical structure, and a systematic approach. Furthermore, a case study is conducted to demonstrate the real-world applicability of the proposed method. Finally, the resilience index isintroduced as a straightforward summation of ranked impact factors, providing a clear metric for resilience assessment.

Dec 15, 2025

By Frank Hirthammer

Over the past few years, development and implementation of digital logistics solutions has convinced users of many additional advantages of this technology. Barcode labeling and reading increases the company’s efficiency and safety by reducing handwritten documentation and preventing misinformation. Sustainable information and productivity management is a significant advantage in competition. Since manufacturing information is tracked throughout the whole supply chain until the final consumer, all processes become transparent what ensures efficient risk tracking, correct disclosure to authorities (if required), and the compliance with company rules.

Jan 1, 2018

By James Pile

Since C.C. White introduced coalmine roof trusses in 1967. many different systems have evolved. Beginning in the mid 1990's, several types of bar/cable truss systems have been introduced. A new and innovative bar/cable truss recently introduced offers several advantages. By eliminating many small parts, and simplifying the installation, this new truss increases operator safely. In order to fully benefit from the new truss system, a closer look at the individual components and their interaction was undertaken to understand critical implications on preload and overall support capabilities.

Jan 1, 2004

By K Zic, P Pickering, P Fraser

Water is a defining feature of the Pilbara. Its management was and remains vital for the pastoral industry which European settlers established when they first came to the Pilbara, and for the mining industry which now dominates economic activity in the Pilbara. Water availability in the Pilbara is, however, problematic. Severe droughts and major floods can occur at close intervals. In response to this uncertainty, the Department of Water undertook a Prefeasibility Study to determine, at a high level, the water requirements and opportunities in the Pilbara region. This paper reports on the outcomes of this study and the water integration opportunities in the region, identifying the sources of water supply and offers possible options for managing this water sustainably for the present and future demand. A range of supply opportunities is reviewed including: dewatering from mining operations, surface water, and desalination. All opportunities were subject to order of magnitude costing, including capital, whole of life and retail unit pricing with preferred options receiving further interrogation through triple bottom line (TBL) analysis to prioritise solutions. Options were also subject to intangible quantification (IQ) including benefits from the reduction of carbon emissions to ensure that the preferred option is based on factors other than just the least cost. Demand analysis was undertaken to identify current and future requirements and were assessed through review and integration of regional and sub regional master plans and consultation with mining, agriculture, industry and the community. The paper concludes that the viability of a Pilbara integrated water supply scheme depends on the development of a financial mechanism involving both government and industry participation models. The agreed scheme formed the basis of a submission to Infrastructure Australia for funding assistance.

Jan 1, 2009

By D Henderson, M Germain

The beneficiation of iron ore deposits to yield haematite and magnetite concentrates for steel making processes typically require the use of one or a combination of wet processing techniques based on gravity, magnetic or froth flotation processes. With the need for more cost-effective technologies with a lower water demand, a re-examination of dry processing techniques has been initiated. For example, a dry processing capability may offer an advantage where suitable quality and quantity of process water hinders the development of a particular resource. This paper describes recent laboratory test work for the production of high grade concentrates using dry electrostatic techniques for -300 ¦m haematite and magnetite ores and compares them with magnetic separation techniques.

Jan 1, 2009

By G. Mucsi, F. Kristály, Á. Rácz, É. Gregus, K. Bohács

"Stirred media mills are widely used in the industry for fine grinding. Most of the applications work in wet mode, however dry grinding in stirred media mill comes forward more frequently nowadays. The present paper deals with the differences and similarities of the wet and dry grinding in stirred media mill from energetic and mechanochemical point of view as well. Grinding experiments in batch stirred media mill were carried out with different materials. During the experiments zeolite and kaolin were used as feed material. The grinding experiments were carried out at different stress energy and stress number values; the grinding work was measured during milling. After grinding X-ray diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), particles size analyzes by laser scattering were carried out on the ground materials. As a result of the systematic grinding and analytical measurements a comprehensive comparison was carried out on the wet and dry grinding and their usefulness for mechanical activation in stirred media mill. INTRODUCTION The natural zeolites are crystalline hydrated aluminosilicates of alkali and alkaline earth characterized by the structure that contains frameworks responsible for the high cation exchange capacity (CEC) and absorption capacity. The frameworks are interconnected by cavities and resided by cations variable in size, coordinated by water molecules. Since zeolite comprises SiO4 and AlO4 tetrahedra interlocked by oxygen atoms that are situated in the structural nodes, their characteristics differ due to the varieties in the structure-directing agents and Si/Al ratio (Colella and Wise, 2014; Malekian et al., 2011; Terzic et al., 2017). The most common natural zeolite occurring in high amount, of industrial importance and involved in milling and MA is the clinoptilolite, in the literature equivalent to “natural zeolite” designated for high clinoptilolite bearing volcanic tuffs. Its amount in the host rock must reach ~ 40 % by weight to obtain the CEC and adsorption desired in its applications. In the highest quality rock might reach 80-90 % by weight (Favvas et al., 2016), but most often is the 40-60 % by weight content, associated with smectites, improving the CEC and adsorption of the tuffaceous rock. The application of such natural zeolites is problematic in many cases due to high silica (quartz, cristobalite and volcanic glass) content and beneficiation (concentration and extraction of pure zeolite) are not feasible. Thus, mechanical activation is a possible way to alter the other than clinoptilolite minerals generating high specific surface area and functionalized particle surfaces to enhance adsorption, reaction or particle adhesion. The zeolites easy availability and the utilization cost-effectiveness have prompted the research on their physicochemical and structural properties (e.g. adsorptive and molecular-sieve activity, heat resistance, and microporous cage structure) and finding new options for their application (Kusuma et al., 2013; Musyoka et al., 2014; Rida et al., 2013; Terzic et al., 2015b). Apart from the presence of exchangeable framework cations which are crucial for the adsorption ability, and a certain degree of pozzolanic reactivity. The thermal stability of dehydrated phases is another important characteristic for use of the zeolite in composite materials that are exposed to high temperature. Thereby, the zeolites found a wide application possibility in the design of the construction composites (Albayrak et al., 2007; Najimi et al., 2012; Vejmelková et al., 2015), as well as for resolving of the environmental protection issues like wastewater refining or heavy metal elimination (Gómez-Hortigüela et al., 2014) even from contaminated groundwater using passive methods like permeable reactive barriers (Gombköto et al, 2016). The grinding treatment of zeolite is a common and frequently applied procedure, both on laboratory (Bohács et al. 2017, Faitli and Czél, 2014)"

Jan 1, 2018

By Robert W. Leonardson

The Questa Molybdenite Mine provides a unique opportunity to study the geochemical dispersion of various hydrothermal events, utilizing drill hole analyses. Numerous post-ore factors have altered the primary ore-related geochemical dispersions to the present day configuration, e. g. dikes, faults, hydrothermal convection cells, and weathering. Due to the interaction of an andesitic volcanic pile with the silicic-alkalic generated volatiles, the geochemical haloes of the Goat Hill deposit demonstrate a marked divergence from the classic Climax-type molybdenite ore body. Certainly, however, the similarities to the Climax-type ore body are apparent as potassically-rich fluids have invaded the highly reactive country rock.

Jan 1, 1984

By M. Hardy

"The structural design of mine headframes is challenging due to the significant differences in the geometry, rigidity, and behaviour of these structures compared to conventional buildings. The differences are related to the main purpose of these structures, which is not human occupancy, but rather the support of hoisting equipment. The main objective of this paper is to present the seismic elastic behaviour of headframe structures in comparison with conventional buildings, which is the base case for the definition of seismic loads. This paper highlights the impact of backlegs on the dynamic behaviour of mine headframes, more specifically the resulting torsional sensitivity. INTRODUCTION The design of industrial structures is often governed by industrial processes rather than by architectural constraints. In ground-mounted hoisting plants, the structural configuration of headframes must allow clearances around conveyances and ropes while resisting the lateral loads associated with the hoisting equipment. Typically, these structures use backlegs to withstand the lateral loads, which leads to highly irregular structures with unconventional dynamic behaviour. The codes and standards applicable to the structural design of mine headframes in Canada are often incomplete or not adapted to the reality of practising engineers. This situation creates confusion, and engineers must look at various guidelines and international standards to support the engineering calculations required for the design of these structures. The loads resulting from the support of hoisting equipment, such as ropes and conveyances, are usually simple to calculate and are determined based on the information from manufacturer and industry related guidelines. Moreover, the loads associated with snow accumulation and wind are calculated applying the same methodology used for conventional buildings, without any major issues. On the other hand, the seismic loads are often difficult to calculate based on the methodology from the National Building Code of Canada due to the significant differences in the dynamic behaviour of the structures. The resulting structures may be either over-designed or worse, under-designed. Hence, there is a lack of uniformity in engineers’ designs. The latest edition of CSA S16-14 “Design of steel structures” includes Annex M (Informative) “Seismic design of industrial steel structures” to help designers close the gap between the requirements of traditional regulations and actual engineering practice."

Jan 1, 2019

By Fathi Habashi

Solid gas reactions of metallurgical importance can be classified into three groups: Physical processes, e.g., drying and sublimation Chemical processes which may be an addition or a thermal decomposition reaction Electrochemical processes which may be addition, oxidation-reduction, or displacement reactions. Examples are given and the role of the boundary layer is emphasized.

Jan 1, 1996

By Zhijing Zhang, Ramana G. Reddy

"The viscosity of molten oxides is one of the important physical properties since viscosity has a decisive influence on fluid flow. The knowledge of the viscosity of molten oxides is essential for modeling and controlling of metallurgical process. In the present study, viscosities of high basic Na2O-B2O3 and Na2O-SiO2 binary melts and viscosities of Na2O-SiO2-B2O3 ternary melts were measured as a function of temperature and composition. Experiments were carried out using rotary viscometer and graphite components. Our experimental results were compared with those in literature. Based on the current experimental data, the previously developed viscosity model was modified. The characteristic features of viscosities of these melts have been discussed. The predicted viscosity results are in excellent agreement with the present experimental data in the temperature range with molten state samples. IntroductionThe viscosity of molten oxides is one of the important physical properties since this property has a decisive influence on fluid flow, and is one of key factors to be taken into consideration in process modeling. The manufacturing operations require the viscosity of molten oxides to be within certain ranges. Although, some viscosity measurements on borosilicate systems have been carried out [1-4], the viscosity data in literature are available only for a few temperatures and cover small composition ranges. The agreement between the results of these works is not satisfactory [I-4]. Even the viscosities of binary systems Na2O-B2O 3 and Na2O-SiO2 generally are well studied, the available viscosity data in literature are only found in the composition range of O to 0.333 mole fraction ofNa2O. The aim of the present study is to provide a base with accurate experimental data for reliable model extrapolation."

Jan 1, 1999

By A. Mainza, H. Hill, L. Bbosa

"The main objective of ore breakage characterization is to quantify the relationship between the energy supplied for breakage and the size of the resultant progeny. In this study, the ore breakage characteristics of drill core particles and crushed particles were compared. Single impact breakage tests were conducted on a basalt ore sample using the JK rotary breakage tester. The size-dependent model by Shi and Kojovic was used to fit the breakage data because the effect of initial particle size is accounted for in the model. It was found that crushed particles consistently gave a higher degree of brokenness than drill core particles and the differences were attributed to the internal structure of the particle. Drill core particles contain a lower crack density (paths of weakness) than crushed particles which have been pre-weakened during the crushing process. An increase in crack density is directly related to a decrease in the minimum threshold energy. Upon application of a stressing force above the stress threshold, particles with a higher crack density will fracture more easily because of a higher rate of crack propagation due the numerous paths of weakness available. It was therefore concluded that under the same conditions, drill core particles are more competent than crushed particles. INTRODUCTION Comminution devices have commonly been reported as being the largest energy consumers in mineral processing circuits (Napier-Munn, 2015). Cleary (1998) reported that the inefficiency of comminution devices is a result of less than 5% of the supplied energy being utilized for breakage, with the majority being expended as heat and noise. With steadily declining fossil fuel supplies and a looming global energy crisis, the mineral processing industry has increased its focus on energy reduction measures. Ore breakage characterization plays a critical role in the design and optimization of comminution circuits (Tavares and King, 1998). The main objective of ore breakage characterization is to empirically quantify the relationship between the energy supplied for breakage (specific input energy) and the size of the resultant progeny through laboratory particle breakage tests (Napier-Munn, 1996). Commonly used laboratory breakage devices include the Drop Weight Tester (DWT), Split Hopkinson Pressure Bar (SHPB) and more recently, the JK Rotary Breakage Tester (JKRBT). Typically, a standard single impact breakage test procedure consists of a matrix of experiments on particles in four to five narrow size fractions each tested at low, medium and high energy levels. The resultant progeny of each test is sized to obtain a particle size distribution (PSD) from which the degree of breakage, usually in the form of a t10 value (percentage of the progeny material that passes 1/10 of the feed size) can be obtained for each size fraction and energy level (Napier-Munn, 1996)."

Jan 1, 2018

By Vaughan R. Voller

"Solidification systems from conduction controlled freezing of a pure material through to alloy phase change that include flow and segregation processes are described. The components in a general solidification model-variables, governing transport equations, and local scale relationship-are outlined. A central focus is the presentation of an explicit procedure for coupling between macroscopic and local scale variables.IntroductionSince the seminal work of Byres et al.[!] in the 1940's there has been a steady progress in modeling solidification systems with increasing levels of complexity. The object of this paper is to track the evolution of these solidification models and present a general modeling approach that applicable to a wide range of the solidification systems of current interest.Solidification SystemsIn a broad sense the underlying physics in a solidification process occur at two distinct length scales:1. The macroscopic scale of the process over which the governing transport equations of heat, mass and momentum hold.2. The local scale at the solid-liquid interface where the solidification phenomena are operative."

Jan 1, 1999

By B. Rai

Processing of dolomitic phosphate ores remains one of the most challenging problems in phosphate ore beneficiation. The beneficiation plant at Jhamarkotra in Rajasthan, India for example is currently using a conventional double stage flotation process which involves first a fatty acids flotation to produce a combined dolomite-apatite concentrate (bulk concentrate) from associated silicate gangue. Dolomite is then separated from this bulk concentrate by flotation with fatty acids collectors and depressing apatite with phosphoric acid and sulphuric acid. This process requires addition of large dosages of reagents (H3PO4 and H2SO4) to depress apatite and to maintain highly acidic pH during flotation. Furthermore several cleaning and scavenging stages are needed to obtain the product of desired quality. We have developed and employed a molecular modelling based methodology of designing selective reagents for apatite-dolomite separation. We have been able to take into ac-count the differences in the distribution of calcium cations on these two surfaces in our design and hence develop novel phosphonic acid based depressants for apatite-dolomite separation with con-ventional fatty acids as flotation collectors. We have demonstrated the utility and power of molecular modelling based reagents design approach through this work on beneficiation of Jhamarkotra dolomitic phosphate ore using our novel phosphonic acids based depressants at pH?s close to natural pH. It was possible to reduce the MgO content of the ore from as high as 13.3 % to 1.5% in a single stage flotation. Our flotation separation results on Jhamarkotra ore with these new phosphonic acids based tailor-made depressants for apatite-dolomite flotation separation are discussed in this paper along with results of corresponding molecular modelling computations on the same system.

Jan 1, 2014