Search Documents

By Kathleen J. D?Amico

THIS SUMMARY is identical to the summary given in volume III of this series of mineral production in the United States (including Alaska and Hawaii), its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico and of the principal minerals imported into and exported from the United States. For further details on production see commodity and area chapters. A summary table comparing world and United States mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers [ ]

Jan 1, 1958

By Y. P. Chugh

The paper discusses laboratory and field studies to analyze time-dependent deformation behavior of immediate weak floor strata in an Illinois coal mine. In the laboratory, core samples of the immediate floor strata were subjected to incremental creep tests under unconfined compressive stress. Both axial and lateral creep deformations were recorded. Time-dependent behavior was reasonably characterized by a Burger model with one Kelvin-Voigt unit. The elastic and viscous parameter8 of the model were found to be stress-dependent, but in the range of 40% to 80% of the failure stress, the effect of stress was relatively small. Therefore, a linear visco-elastic model was developed to represent the laboratory time-dependent behavior of immediate floor strata. Such a model may be acceptable for the design of partial extraction mining systems having extraction ratios of 40% to 60%. Field observations of roof-floor convergence (floor heave) at the mine also indicated a time-dependent behavior similar to that observed in the laboratory. Field time-dependent behavior was also characterized in terms of a Burger model with one Kelvin-Voigt unit to obtain scaling factors between the field and laboratory parameters. This approach should help in predicting likely floor heave in the mine based on laboratory creep tests. It was concluded that additional studies in the field are required to arrive at more reliable correlations between the two sets of parameters.

Jan 1, 1987

By Frederick B. Brien

For many years tin mining in Bolivia has been very important to the economy of the country. In recent years the tin content of the ore reserves has been steadily declining. An improvement in concentration efficiency is highly desirable in order to increase productivity from the present-low-grade mine ores and to allow retreatment of the many millions of tons of tailings from past operations, some of which equal the present ores in tin content. A number of investigators have been or at present are working on various phases or approaches to the problem. Gravity concentration is used in Bolivia today as it has been in the past to recover tin minerals from the mine ores. An objective of the work reported in this paper was to examine the possibility of treating present low-grade ores and sink-float tailings products, at a relatively coarse grind, in order to produce a higher grade feed material to the present gravity concentration plants. The possibility of using heavy liquids in cyclones to treat large tonnages with a minimum of outlay presented itself and is of particular interest since appropriate heavy liquids are available and with physical properties which lend themselves to simple recovery methods. Tests were carried out using a closed circuit laboratory cyclone assembly. It was desirable to determine the value of using the SG50 concept and Tromp curves for analyzing the cyclone concentration test results. The effects of entrained water on the behavior of ore particles in the cyclone were examined.

Jan 1, 1964

"The JKMRC researchers have been redeveloping the suite of breakage testing techniques to more realistically align with the breakage environment in comminution equipment. Computational modelling, especially with the DEM, has highlighted the modes of impact and contact, along with the energies of these interactions in a wide range of equipment. This has driven the need to match these modes in laboratory ore characterisation tests. The objective has been to build a continuum of breakage tests and associated models that span the required range of breakage forces and environments. The ore sample is subjected to a sequence of tests covering: abrasion (surface breakage) of angular through to smoothed particles; single particle impact from high energy single impact breakage down to low energy; incremental breakage covering 60 mm down to 50 µm particles; particle strength distribution; and bed breakage over a range of compression and energy input. These tests are suited to multi-component ores with a distribution of strengths. A modelling technique is also being developed to utilise primary breakage for modelling breakage under different types of confinement. This paper draws together these techniques, previously published by the authors, into a coherent whole. The suite of tests is approaching the point where a fixed set of tests can be used to model the performance of a full range of equipment, removing the need to conduct repeat ore characterisation tests for each different piece of equipment incorporated in a circuit design. This path should open up the application of different circuit configurations and novel equipment in comminution circuit design.1 INTRODUCTION Comminution modelling utilizes a wide range of ore characterisation techniques and methods to deal with the range of comminution equipment available for production use. In general, the tests have been designed to correlate with specific pieces of equipment, using calibration factors to provide the link between the small-scale test and industrial-scale performance. The majority of tests focus on estimating the power requirement of process equipment to achieve a desired throughput and grind size. Overall, this approach has achieved acceptable outcomes in the past, but the reality is that equipment sizing suffers from considerable uncertainty, in excess of ±20% is not uncommon. This uncertainty is covered by safety margins and automatic scaling factors in equipment selection. In striving to improve reliability, the industry tends to add more adjustment factors to the tests, and design margin rather than question the basic validity of the testing process. As the tests are often correlated to production equipment via carefully guarded databases, they are also locked into historic operating inefficiency, not providing direction or revealing opportunities to improve production efficiency in comminution equipment or circuits. Safe in the knowledge that they are achieving the expected production based on test work predictions, a site is unlikely to set their sights on reducing specific energy consumption by 10%."

Jan 1, 2018

By B. K. Cantrell

The U.S. Bureau of Mines and others have conducted a number of occupational exposure surveys since the publication of the International Agency for Research on Cancer report of 1989, which labeled diesel exhaust as a probable human carcinogen. These surveys have assessed diesel exhaust exposure using measurement of diesel aerosol and/or specific polycyclic aromatic hydrocarbons as indicators of exposure. This paper reviews present diesel emission standards, available diesel exhaust aerosol measurement techniques, and the results of the occupational exposure surveys. In the surveys, diesel aerosol was emphasized because it is a major component of diesel exhaust, is suspected to contribute to the health hazard, and is readily measurable. Three primary aerosol measurement techniques were used: respirable combustible dust, size-selective sampling, and measurement of the elemental carbon fraction. Occupations surveyed included mine workers, railroad workers, forklift operators, fire fighters and truck drivers. The studies found mean diesel aerosol concentration levels in the range of 0.004 to 1.74 mg/m3? Highest aerosol exposures were in confined spaces such as mines where heavy diesel equipment is used. Polycyclic aromatic hydrocarbons typically are found at very low concentration levels and are not unique to diesel exhaust.

Jan 1, 1996

By Th. G. Sahama

This paper contains some new thermodynamic data for silicates in the series Mg2SiO4-Fe2SiO4 and MgSiO3-FeSiO3 and Lives the result: of a thermodynamic attack on the problems of stability end paragenoses. Although some data are lacking, satisfactory agreement with mineralogical and petrological observations is indicated.

Jan 1, 1949

Adsorption experiments were conducted at two different solids loadings, to investigate the mechanism of oleate adsorption on apatite. Adsorption density at pH 10 was found to be dependent on solids loading in an oleate concentration region where surface precipitation could occur. Analysis of adsorption isotherms indicated three distinct regions of adsorption. In the region I (below the region of calcium oleate precipitation), molecular adsorption was observed. Simultaneous molecular adsorption and surface precipitation occurred in region II, while surface precipitation was predominant in region III along with some bulk precipitation. Correlation between flotation of apatite with sodium oleate and the mode of oleate interaction with the surface is established.

Jan 1, 1986

By Seong-Ho Ha, Shae K. Kim, Young-Ok Yoon

In the this study, surface segregation of Mg and Ca with Mg addition range from 5 to 10wt% in Al-Mg alloys with Mg+Al2Ca master alloy and its effect on the oxidation resistance were investigated. The addition of Mg+Al2Ca master alloy as the Mg alloying element led to the surface enrichment of Mg and Ca during high temperature oxidation. As a result of the oxidation test by TGA, the oxidation resistance of all the examined alloys was significantly improved with increasing Al2Ca content. The weight change of Al2Ca added Al-5Mg and Al-7.5Mg alloys indicated the complete oxidation resistance during the whole oxidation test time, while a slight weight increase was shown in the case of Al-Mg alloys even with Al2Ca addition. The improvement of the oxidation resistance in Al2Ca added alloys may be attributed to the formation of the protective oxide layer mixed with CaO and MgO on the surface.

Jan 1, 2015

By Duncan GR

Having passed through a number of previous phases the best longwall results in Australia have shown a significant increase in the last two years. The results expected from a longwall face can be estimated from the ideal production rate, determined by the capacity of the equipment and the conditions in which it is installed, the utilisation, and the available operating hours. Back analysis of the results achieved suggests that, on average, recent improvements arise from the higher capacity equipment recently installed; the utilisation has in fact reduced slightly. Review of the constraints which limit the longwall results, i.e. shearer speed, AFC capacity, support, advance rate, and man travel speed, shows that little improvement can be expected in the ideal production rate in thinner seams. In thicker seams the AFC often proves the overriding constraint and further increase in equipment size could lead to increased future ideal production rates and is expected. In all cases a concerted effort to increase the utilisation achieved is likely. For deep mines with thin to medium seams this offers the most viable path to improvement; by contrast thick seams with highwall/shallow access may benefit from further increase in equipment size.

Jan 1, 1988

By Paul J. Barrett

The Bureau of Mines evaluated a sulfurous acid-sulfuric acid process for recovering alumina from clay, in which clay is leached. successively with sulfurous acid and sulfuric acid. The resulting aluminum sulfite and aluminum sulfate solutions are combined and heated to produce a basic aluminum sulfate and sulfur dioxide. Alumina is extracted from the basic aluminum sulfate as sodium aluminate by leaching with dilute sodium hydroxide. After desilication, sulfuric acid is used to precipitate alumina as alumina trihydrate, which is then calcined to alpha-alumina. The estimated fixed capital cost for a plant producing 1,000 tons per day of alumina is about $74 million on a 1971 basis. For comparison with previous alumina-from-clay evaluations, the estimated fixed capital cost for the plant is about $67 million on an M and S Chemical Equipment Index basis of 24.0.0, which is equivalent to a 1960 cost level. Because the operating cost is highly dependent on fuel and electric power costs, graphs are included to show the effect of these items on the operating cost. On a 1971 basis, with natural gas costing 35 cents per million Btu and operating labor costing $4 per hour, the estimated operating cost is about $100 per ton of alumina. On a 1960 basis, with labor costing $2.30 per hour and natural gas costing 25 cents per million Btu, the estimated operating cost is about $86 per ton of alumina.

Jan 1, 1973

The discovery of copper and nickel sulphides in the Riwaka Complex in 1967 led to considerable exploration activity by a number of companies. Various exploration techniques used by these companies are summarised and discussed. Activity of these companies shows that mineralisation is mainly confined to the southern, ultramafic section of the Riwaka Complex where geological mapping recognised sixteen units within, or associated with the Riwaka Complex. Significant pyrrhotite, pentlandite chalcopyrite mineralisation is restricted to biotite feldspar pyroxenites and to clinopyroxenite units. Lesser and more erratically distributed pyrite chalcopyrite pyrrhotite mineralisation occurs in poikilitic pyroxene hornblendites, melanocratic gabbros, and in marginal diorite lenses. It is suggested that a linear belt of layered ultramafic and mafic rocks described in Fiordland by Williams (1974) may be a southern extension of the Riwaka Complex. The Riwaka Complex has been classified as belonging to the Picritic subtype, (Tholeiitic suite), of Naldrett and Cabri, (1976), and as such it is concluded that it exhibits substantial potential for the discovery of economic copper and nickel deposits. It is considered that the complex is a multiphase differentiated intrusion emplaced in a major tensional fracture zone that developed in a relatively stable tectonic environment, namely a succession of middle Paleozoic shallow water shelf sediments. Based on sparse available evidence it is suggested that the Riwaka Complex was intruded in the lower to middle Permian. It is further suggested that the tensional fracturing was initiated by the onset of subduction process which were responsible for the development of the Permian volcanic arcs and ophiolite belt in the north west Nelson area.

Jan 1, 1977

By D. J. Maconochie

This paper describes the investigations and results of monitoring of deformations of houses located within the area of influence of a pillar collapse over the Westfalen No. 3 coal mine near Ipswich, Queensland. The subsidence resulted in minor subsidence of at least 18 modern houses and serious damage to 4 others. The history of the events and the measures taken to deal with the physical problems arising are described. The investigations and results are described and related to the mining methods and geology. The stability of coal pillars up to 9.6 m high was considered and computer modelling undertaken to relate surface subsidence to estimates of the extent of pillar failure. Assessments were made of the likely extent of subsidence during the incident. Measurements of distortion and tilt were obtained as the ground slowly subsided and criteria established to determine when the structures were deemed to be unsafe. Detailed surveys of houses affected or anticipated to become affected were also undertaken. Four houses were condemned and subsequently demolished as a result of excessive tilt. The methods of assessment are described and the implications of the results related to the various house designs.

Jan 1, 1992

By L. S. Bbosa

Single particle impact breakage experiments provide essential data to aid in understanding of rock fracture in comminution. Such experiments, conducted using devices such as the drop weight tester, split Hopkinson bars and more recently the rotary breakage tester, have been successfully used to characterize ore breakage properties in relation to measured fracture energies. The work presented in this paper highlights the techniques behind the calculation of impact breakage properties from each of these three devices. The breakage parameters that can be calculated from experimental data from each of these are to be described. Drop weight tests are used to calculate A and b hardness parameters using the standard JK breakage model. Split Hopkinson pressure bars are used to establish the ultimate compressive stress of particles through single impact breakage tests and the fraction of impact energy utilized to cause particle fracture. Low energy breakage tests using the rotary breakage tester are shown to be used in calculating particle breakage probability. Methods to calculate parameters related to particle breakage probabilities such as E0 and Ecrit are also discussed.

Jan 1, 2014

By Sen S. K, Banerjee D. D, Nandy D. K

It has been stressed that the intrinsic spon- taneous heating characteristics of a coal is not enough in predicting spontaneous fire risk of a mine. The influence of extraneous conditions created from the system of mining operations are also to be reckoned with, A case study was made with a mine in Jharia field, India, being proposed to be developed under short wall method with complete extraction in 4-5 slices followed by stowing.

Jan 1, 1988

By Frederick K. A1lgaier

The Bureau of Mines' Denver Research Center initiated a subsidence research program in 1978. The short ten goals of the program were to determine practical methods and equipment for measuring subsidence and demonstrate these methods by monitoring subsidence at several mines having mining, geologic and topographic variables typical of those encountered in the western United States. Data from the monitoring program would be supplied to cooperating mining companies and used by the Bureau to accomplish the long term objective of developing and validating subsidence prediction techniques applicable to mines in the West. Subsidence monitoring is being conducted at five mines in Colorado and Utah with substantially different mine plans, mining methods, depths of cover, and topography. The monitoring procedures used at each site are similar and include designing the monitoring network layout, installing the subsidence monuments, initial and periodic surveying of the monuments, and processing the survey data. The network layout, surveying methods, and types of monuments vary according to the conditions at the individual sites and the type of data being collected.

Jan 1, 1982

By Dipl. -Ing. H. -J. Sager

The ‘Westerschelde Tunnel’ underpasses the estuary of the Schelde in the Netherlands. The tunnel will consist of two tubes which are driven by two hydroshields (slurry shields). The tunnels will each have a length of approx. 6.6km and a bore-diameter of 11.33 m. Demanding ground conditions had to be considered during the design of the shield machines. Loose sands, extensive clay formations and high ground water pressures of up to 6.5 bar will be encountered during the tunnel drive. The tunnelling activities will start in the middle of 1999 and are scheduled to end by the end of 2001.

Jan 1, 1999

By Deno Pappas

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has been evaluating developments in sealant support systems from a ground control perspective. The proper selection and use of a sealant material can significantly enhance ground control which may result in a decrease in worker related injuries due to ground falls. The purpose of this paper is threefold: to briefly review the current state¬of-the-art technology in shotcrete and membrane developments, to evaluate the preliminary findings of a long-terra underground study of various types of sealant materials, and to examine installation practices that are critical for an effective sealant material. The underground study utilizes NIOSH's Lake Lynn Laboratory Experimental Mine to evaluate the long-term performance of several types of shotcrete and membrane materials. Sealant performance to date have been evaluated on a regular basis over a two year period. Although the study is still ongoing, critical mining practices were identified that may seriously effect the bond of the sealant materials to the mine roof and rib; most notably, the importance of scaling and thorough cleaning of the rib prior to application. Also, results from an extensive series of Schmidt Hammer tests found that the shoterete increased in strength by 70% during the humid summer months.

Jan 1, 2002

By K. D. Eng, W. T. Tierney

"During the past century, the development of vehicular transportation has benefitted tremendously from the performance improvement in engines in a situation where low-cost, plentiful fuel supplies were the order of the day. Engine advances were enhanced by and also dictated fuel modification to better adapt the energy source to the power plant.In discussing the several aspects of the change in approach from ""an engine and its fuel to a fuel and its engine"", the authors touch on the following areas:1. Description of an engine concept that provides the needed flexibility in fuel appetite at good efficiency to cope with future requirement s.2. The constraints placed on liquid fuel resource energy utilization efficiency by special engine-required fuel properties and the fuel efficiency of the various engine types available.3. Future vehicle engine fuel sources. This review will put into perspective the problem associated with the net energy available from future fuel sources under extensive research and development at present.4. A brief review of test data to show that fuel-tolerant and fuel-efficient engines are viable and that, in a fuel-resource-limited future, they can be a ""light at the end of the tunnel.""The Texaco Controlled Combustion System (TCCS)The TCCS is a unique means for stratified charge operation of an internal combustion engine in such a manner as to eliminate the requirement for octane or cetane number specification for the fuel. Octane rating is an empirical engine test method that evaluates a gasoline's resistance to spontaneous ignition or ""knock."" Cetane is based on a different engine test, which determines a diesel fuel's ease of spontaneous ignition . High cetane number enhances cold starting and permits high-speed diesel engine operation. As one would expect, the fuels in current use cover a band when the two values, octane and cetane, are plotted against each other."

Jan 1, 1982

By K. G. (Ken) Thomas

"This paper gives an insight into the various processes available to treat gold ores. A brief overview is given of the various types of refractory gold ores. Particular emphasis is given /0 comparing the costs of oxide vs refractory gold ore processes, inclusive of grinding through to dore bar.HistoryThro ugh time gold has been recovered from the earth's crust by various mean s. Five major historical steps can be identified for metallurgical processing as shown in Table I .Gravity concent ration started with, for example, river bed panning and developed to more sophisticated processes such as the Johnson concentrator, belt concentrator and jigs. The South African gold fields were a major developer of gravity concentration processes during the first half of the twentieth century.As coarse free gold became depleted, stamp milling, in conjunction with amalgamat ion , was developed. Basically, rock was crushed under large mechanical hammers an d the gold collected in mercury . The mercury was then evaporated in a retort to leave sponge gold for further fire refining.As deposits became deeper and gold finer, the gold became more difficult to recover ; fine grinding was required to liberate the gold. In the 18905, MacArthur and the Forrest Brothers of Glasgow, Scotland, introduced the cyanide pro cess for dissolution of gold and its subsequent precipitaiton by means of zinc. This process, in vogue until the early 1970s, was commonly referred to as the Merrill-Crowe process for recovering fine gold .Activated charcoal was used as a means of recovering gold from solution in the 1880s, especially in chlorination plants in Australia( l). Two factors probably retarded the development of carbon instead of zinc-based processes during those year s. First , there was no satisfactory procedure for the elution of carbon to allow its recycling and, second, the development of the Merrill-Crewe process for gold recovery by zinc cementation probably discouraged any further work on the use of carbon"

Jan 1, 1991

By O. E. Humeniuk, A. I. A. Salama, M. W. Mikhail

"Performance testing of prepartion plants is referred to as plant audit. It evaluates plant performance under normal operating conditions and is aimed at improving yield through knowledge of actual process performance and interactions between different processes in a plant.This paper describes the program to evaluate the performance of several Canadian preparation plants. The performance test requires the planning of a sampling campaign that would include all circuits in the plant. Samples are analyzed to determine washing characteristics (screen and float-sink), ash and per cent solids of feed and products of separation units in the plant. Performance characteristics are established based on analysis and material balance. Specific recommendations can then be made to improve recovery, and identify and explain potential causes of apparent deficiencies.The objectives of the program are to reduce the cost of production by improving recovery of clean coal and, in tum, to reduce disposed tailings, establish baseline information on coal preparation plants performance in Canada, and define R&D work needed to optimize plant operation."

Jan 1, 1993