Search Documents

[Scott Aberle Western Energy Co POB 99 Colstrip, MT 59323-0099 Randy Acre Joy Mining Machinery 2569 Silver Oak Ct. Grand Junction, CO 81505 Brian L. Acton Oxbow Carbon & Minerals Inc 1601 Forum P1-#P2 West Palm Beach, FL 33401 Laine W. Adair Genwal Resources Inc POB 1420 Huntington, UT 84528-1420 Kent Adamson Solvay Minerals POB 1167 Green River, WY 82935]

Jan 1, 1999

Although the technology involved in removing material from below the earth's surface has a long history, communication systems in underground workings are relatively new to the industry. Communication equipment did not begin appearing in underground mines until the early 1900's. Figure 1-1 shows a miner using a Western Electric standard telephone set for underground mines in 1913. These early phones were essentially the same as those used aboveground, except that they were enclosed in cast-iron boxes as protection against moisture, acid fumes, and gases.

Jan 1, 1984

By N. A. Barcza

INFACON 7, the seventh International Ferro Alloys Congress, took place in Trondheim, Norway, in June 1995. The main aim of the Congress, which was held under the auspices of Euroalliages and the Norwegian Ferroalloy Research Organization, was to present the challenges facing the ferro-alloys industry on the road to the 21st century. Halyard Tveit, Chairman of the Technical Committee, summarized these as: ? the transition to a single global market economy ? new demands with regards to quality arising from customer needs, and ? increased awareness of the global environment. In the Plenary Sessions Kouichi Nakamura (Nippon Steel) outlined, from the steel industry's point of view, the relationship between technical advances in the products and more demanding ferro-alloy specifications. Advances in steel manufacturing technology and higher product quality have been supported in the past by raising the quality standards of ferro-alloys. Future requirements are bound to bring about more severe standards, and these need to be established by common agreement between both industries.

Jan 1, 1996

Public perceptions about coal remain neutral to negative But gains are slowly being made as the public becomes more aware of coal as ?abundant, affordable, and increasingly clean?

Jan 1, 2006

By L. W. Saperstein

One of the most critical skills developed by underground coal miners is the ability to interpret natural warning signals in terms of impending roof failure. A miner receives a variety of signals which can be called warning and which can be classed broadly by sense: aural, visual, and tactile. This paper concentrates on those signals which are airborne and audible. These signals are creaks, cracks, pops, groans, snaps, booms, tears, rips, and other assorted pulses which emanate from the roof strata, coal pillars, and artificial support in response to the stresses induced by the mine opening. These pulses are sometimes referred to as "talk". Although it is clear that miners rely on roof talk to assess the roof's stability, it is not clear of what roof talk is composed. It has been described in a variety of figurative ways, but has not been scientifically characterized. As will be shown shortly, the purpose of this research is very specific. The ramifications, however, are very broad, and are, indeed, still being followed.

Jan 1, 1974

By Michael S. Miller

In 1987, 1988 and 1989, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the Sperry Creek Wilderness Study Area (OR-003-035; 5,600 acres) and the Gold Creek Wilderness Study Area (OR-003-033; 13,600 acres), plus an additional area (OR-003-033; 2,180 acres) adjacent to the Gold Creek Wilderness Study Area. The wilderness study areas and the addition are south of the Malheur River and are about 20 miles east of Juntura, Oregon. The wilderness study areas and the addition are underlain by volcanic rocks, predominantly basalt and rhyolite flows, breccias, and welded ash-flow tuffs. Lacustrine deposits containing diatomites occur mainly at the east side of the Gold Creek Wilderness Study Area and addition. Alluvium lies along the Malheur River, in terraces and fans south of the Malheur River, and along the floors of some creeks. Shear zones and faults have offset the rocks and provided channels for eruption of volcanic rocks and epithermal mineralization by hot springs.

Jan 1, 1989

[Aamot, Olav Crone, (M'29) Chem. Engr., Elektrokemisk, Raadhusgt. 23, Oslo, Norway. Abadilla, Quirico A., (M'38) Min. Engr., Dir. Bureau of Mines, Manila, P. 1. Abbott, Agatin, (J'40) Asst. Geol., Trench Mine, Patagonia, Ariz. Abbott, Clarence E., (M'04) Civil Engr., V.P., Tennessee Coal Iron & R.R. Co., 1642 Brown Marx Bldg., Birmingham, Ala. Abel, Raymond L., (M'28) Prof., Chem. Engrg., Univ. of Pittsburgh, Pittsburgh, Pa. Abel. Walter D., (M'32) Min. Engr., Div. of Corporations, State of Calif., 403 California State Bldg., Los Angeles, Calif. Abele, Louis T., (M'31) 4800 Patterson Ave.. Richmond, Va. Abell, Leo M., (M'31) Research Met., Mount Morgan Ltd., Mount Morgan, Queens., Australia. Abenius, Hakan V., (M'37) c/o Falu Gruva, Falun, Sweden.]

Jan 1, 1940

By Craig M. Jensen

A laboratory assessment of prompt and delayed neutron activation analysis with 252Cf and 14MeV neutron sources, for use as an in-situ method of determining low-level copper concentration has been performed. A simulated borehole using porphyry ore was constructed and varying copper concentrations were simulated using copper rods. Prompt neutron activation analysis experiments were consistant with earlier work and do not appear to be feasible fur copper concentration of 1.5% or less. Delayed neutron activation analysis experiments indicate that copper ore concentrations of less than 0.1% are detectable using either the 511-KeV gamma-ray of copper-64 or the 1039-KeV gamma-ray of copper-66, with high resolution detectors such as Ge (Li) or intrinsic germanium.

Jan 1, 1977

By L. D. Tracy

The first study of this subject hits been made in Illinois, but as opportunity affords, similar studies will be made in other States. It is hoped that the data obtained will assist the coal-mining industry to standardize the forms of leases, and so avoid some of the abstruse and ambiguous clauses which slay be found in many of them and the consequent liability of costly litigation. In some of the publications of the Illinois Mining; Investigations prepared under a cooperative agreement with the U. S. Bureau of Mines, the Illinois State Geological Survey and the Engineering Experiment Station of the University of Illinois, the coal areas of the 'State have been divided into eight geological districts, each district being treated separately. This report covers District No. VI of that classification, and it is hopped that studies of the other districts will be completed in the near future and similar results published.

Jan 1, 1926

By Deni Côte, Michel Dagbert, Marcel Vallée

"Greater reliability of mineral deposit and reserve estimates can be attained through better quality control of the data and information acquisition, and the estimation processes. This paper reviews the following key requirements:1. greater awareness of the significant figures of both data and estimates, and better understanding of the probabilistic aspects of the estimates, their confidence limits and margins of error;2. greater reliability of the information that supports the estimates, by more explicit and more rigorous methods and standards for data acquisition and for interpretations;3. more quantitative estimations of geological/mineral continuity, based on improved three dimensional sampling patterns and the use of geostatistics; and 4. better integration at the project engineering and mine production stages, of the mineral deposit characteristics and mining method constraints, for more efficient mineral recovery and mine quality control.RÉSUMÉUne plus grande fiabilité des estimations des gisements et des réserves minières requiert plus d'emphase sur le contrôle de la qualité de I ‘acquisition de l'information et du processus d'estimation. Les exigences suivantes sont revues:1. le respect du niveau d'exactitude des données et des estimes en n'utilisant que le nombre approprie de chiffres significatifs des observations et mesures, et en exprimant le niveau de confiance et la marge d'erreur des estimations;2. l'amélioration de fa fiabilité des données par des normes plus rigoureuses pour leur acquisition et leur vérification, et par des méthodes plus systématiques d'interprétation et de modélisation;3. l'estimation plus rigoureuse de la continuité des minéralisations dans les trois dimensions des gisements, par des patrons échantillonnages mieux adaptes awe paramètres géologiquement minéralogiques, et par l'utilisation des méthodes géostatistiques; et4. l'intégration plus poussée, particulièrement lors de la planification de l'exploitation minière, des caractéristiques des gisements avec les contraintes des méthodes d'exploitation, pour améliorer la récupération et le contrôle de la qualité en exploitation."

Jan 1, 1993

By Jacob N. Frank

A factorially designed, hydraulic fragmentation experiment using a high-pressure water jet was conducted on concrete blocks. Three levels of pressure, standoff distance, and impact angle and two levels of traverse time and surface condition were used. Three variables were measured: depth of penetration, volume of material removed, and width of slot. Three stepwise linear regression equations were developed from the jet parameters and the physical properties of the concrete. The three basic equations, describing the significant jet parameters and physical properties, were developed into 15 predictor equations, five for each variable investigated. Direct regression equations were also developed for each variable investigated to show the result of increasing or decreasing each significant variable. Energy efficiencies were developed for the experiment and for each significant factorial variable.

Jan 1, 1971

Jan 1, 1925

By R. J. Hundhausen

The continued worldwide shortage and strategic value of nickel place great importance upon the continued development and exploitation of new sources of nickel in the United States, The deposits of nickel-bearing minerals in Oregon and Washington have attracted considerable attention, particularly since the Hanna Development Co. has engaged in development work aimed at producing ferronickel from the Nickel Mountain deposit, near Riddle, Douglas County, Greg. The Red Flats nickel deposit in Curry County, Oreg., was first examined by the Bureau of Mines in dune 1945, but it was not until 1952 that the deposit was drilled and sampled. In 1953, a 15-ton sample of Red Flats material was procured and subjected to continuous smelting tests in the Bureau's Northwest Electrodevelopment Laboratory, Albany, Greg.

Jan 1, 1954

This paper is not available for inclusion in the Proceedings at the time of printing, but it will be included as an insert.

Jan 1, 1984

By Gamal Rashed, Zorica Radakovic-Guzina, Khaled Mohamed

"Underground coal mines use mechanical bolts in addition to other types of bolts to control the rib deformation and to stabilize the yielded coal ribs. Limited research has been conducted to understand the performance of the mechanical bolts in coal ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted this work to understand the loading characteristics of mechanical bolts (stiffness and capacity) installed in coal ribs at five underground coal mines. Standard pull-out tests were performed in this study to define the loading characteristics of mechanical rib bolts. Different installation torques were applied to the tested bolts based on the strength of the coal seam. A typical tri-linear load-deformation response for mechanical bolts was obtained from these tests. It was found that the anchorage capacity depends mainly on the coal strength. Guidelines for modeling mechanical bolts have been developed using the tri-linear load-deformation response. The outcome of this research provides essential data for rib support design.INTRODUCTIONThe design of rib bolting in U.S. coal mines is based on a trial-and-error process, which is insufficient to eliminate injuries and fatalities caused by rib falls. In the last 10 years, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States (MSHA, 2018). Recently, NIOSH researchers surveyed 90 sites in 14 underground coal mines in the Eastern United States and found that 11 mines are bolting coal ribs, with 4 of those mines using the conventional mechanical bolts and the others using fully-grouted bolts. NIOSH researchers are developing an engineering design procedure for rib support. Pull-out test programs for mechanical and grouted rib bolts were conducted to understand the rib control mechanisms of rib bolts. Only the test results of mechanical bolts are presented in this paper.Mechanical bolt (or point-anchored bolt) is a tensioned bolt anchored down the borehole with a mechanical expansion shell or a resin-grouted medium (Peng and Tang, 1984). The mechanical anchor bolt consists of a plug, a shell anchor, a headed bar with the top end threaded, a bearing plate, a hardened washer, and occasionally a friction-reducing washer. The shell anchor can be either standard or bail type (Figure 1). The standard type shell is held in place by a nut, while the bail anchor uses a strap to hold the shell in place (Peng, 2008). The diameter of the bar is generally 16 mm (? in) for the #5 bolt or 19 mm (6/8 in) for the #6 bolt. The diameter of the hole that the bolt is inserted into must be carefully controlled, since an oversized hole can result in poor anchorage (Moss, 1971). The anchorage is obtained by applying torque to the bolt head, which in turn pulls the plug down in the shell and expands the serrated leaves against the sides of the hole-wall. In the resin-grouted anchor, the resin replaces the mechanical expansion shell at the end of the hole. The anchorage is achieved by bonding between the resin, bolt, and the hole-wall."

Jan 1, 2019

By Richard H. Spencer, Thomas E. Doerfler, Robert L. Lagace, James M. Dobbie, William S. Hawes

This report assesses the expected detectability, on the surface above mines, of electromagnetic signals produced in the frequency band of 630 to 3030 Hz by a rescue transmitter activated by miners trapped underground. This assessment is based on a statistical analysis of experimental signal and noise data taken at a representative sample of coal mine sites well distributed over the United States underground coal fields. Regression analyses are performed to characterize the signal transmission behavior of overburdens as a function of depth and frequency. The predicted signal behavior is then combined with experimentally based distributions of the background noise, and aural detection characteristics of signals in noise, to generate curves of the expected probability of detection for trapped miner signals versus overburden depth and operating frequency. The implications of these results, and associated recommendations, are presented regarding the detectability of trapped miners, sensitivity analyses and confirmatory tests, and operational utilization considerations for the trapped miners and the search and rescue team on the surface.

Jan 7, 1980

By Anil Kumar

In underground mine production units that employ discrete-vehicle face haulage, feeders are used in the belt network so that vehicles can unload rapidly without transmitting to the conveyor network the high material flow rates that result from rapid unloading. They prevent production bottlenecks at the face, while reducing capacity requirements for downstream materials handling equipment. Similarly, surge bins may be installed at intermediate locations in the network to smooth flows from a number of upstream sources, thereby reducing downstream belt capacity requirements. This paper introduces new stochastic process models to temporally describe loading patterns from unit operations and techniques for computing the probability of various fill levels for the feeder or surge bin. These results may be used to analyze the effect of alternative bin or feeder capacities and discharge rates on the performance and costs of the materials handling system.

Jan 1, 1994

By David J. Hatem, K. Bhattarai

Effective risk management in major subsurface projects involves ways to mitigate adverse impacts to final design and construction approaches due to changed subsurface conditions. An Early Contractor Involvement (ECI) collaborated with Observational Method will be an effective contractual tool to address risk developed due to encountering differing site conditions. Observational Method (OM) can further be supported with artificial intelligence (AI) technologies with automated data-driven decision-making features in risk mitigation and implementation of proper design and construction approaches. This paper presents collaborative applications of ECI, OM, machine learning, and risk baselining in risk management and productivity enhancement in tunneling projects.

Jun 23, 2024

By David E. Pearson

"Western Canadian coking coals are located in the Rocky Mountains arid foothills of British Columbia and Alberta. They are typical of non-marine coals, characterized by total sulphur contents of less than one per cent and with ash contents of 10-30 weight per cent. This mineral matter is composed principally of kaolinite and quartz.The petrographic compositions of most of the coking coals which constitute the 2.065 billion tonnes of British Columbia's measured reserves, and the compositions of the metallurgical coal currently exported from Alberta, show them to be rich in the inertinite macerals, macrinite, fusinite and semifusinite. When the mean maximum reflectance of vitrinite in oil/Romax) is used as the coal rank parameter, this high inertinite content is reflected in the lower volatile-matter yields, but the relatively inert character is also displayed by lower free swelling indices (PSI), lower maximum dilatations, lower maximum fluidities and lower coke strengths than other coals of the same rank, but richer in the reactive macerals, vitrinite, exinite and semifusinite. Despite these reduced values in the so-called caking tests, inertinite-rich coals produce strong coke.A system of classification of coking coals is introduced which is based on rank, as indicated by Ro max, and either petrographic composition, maximum dilatation, maximum fluidity or, to a lesser extent, PSI and volatile-matter yield. Six principal coal groups can be distinguished among coking coals using this versatile classification. Inertinite-rich coals are assigned to the Keystone Group (GI), Balmer Group (G3) or Moura Group (G4), each group being named for a coal typical of that population ofcoals. Reactive-rich coals are assigned to the Pittston Group (G2), Kellerman Group (G5) or Big Ben Group (G6). A multiple-regression analysis of coal quality versus price shows how the value of coking coal in the Japanese market appears to be related to reflectance and the free swelling index, and confirms the economic viability of the classification.British Columbia's measured reserves of coking coal contain representatives of four of these groups; Balmer Group (73%), Moura Group (/6%), Pittston Group (3.4%) and Kellerman Group (7.6%).This analysis of the quality of Western Canadian coking coal indicates that despite the need for large proportions of inertinite-rich coking coal in blends produced in the Japanese steel industry, there is nevertheless a demonstrated overabundance of Balmer Group and Moura Group coals available to the international coking coal market."

Jan 1, 1980

By Henry N. McCarl

[The Construction Materials section contains the following Chapters: Aggregates Cement and Cement Raw Materials Crushed Stone Dimension and Cut Stone Lightweight Aggregates Gypsum and Anhydrite Sand and Gravel Insulating Materials-Thermal and Sound Slag Roofing Granules] Mineral aggregates are those natural and manufactured industrial mineral and rock materials that provide bulk and strength in portland cement concrete, bituminous concrete mixes, and plaster or stucco surfaces. They may also provide special characteristics such as thermal and acoustical insulation, weight, surface textures, abrasion resistance, and impermeability to various concrete products and mixes. Most aggregates are relatively inexpensive materials, but despite their low unit value, the tonnages consumed each year in the United States and throughout the" world make mineral aggregates by far the leading industrial mineral and rock materials both in terms of volume (tonnage) produced and value consumed. The major use of mineral aggregates is in concrete. The low cost, high bulk aggregates tend to keep concrete construction costs at levels competitive with other building materials. Other major uses of aggregates include highway and railroad base or ballast materials, graded fill, and various industrial uses such as metallurgical and chemical fluxes and raw materials-these latter uses are often considered nonaggregate uses of mineral aggregate materials. The per-ton value of mineral aggregate materials at the production plant in 1980 and 1981 varied from $2 to $5 for most sand and gravel and crushed stone, $3 to $6 for air-cooled slag, $7 to $20 for expanded slag and expanded clay or shale aggregate, to as much as $165 to $320 for expanded perlite or vermiculite. The expanded lightweight aggregates have been dramatically affected by increasing fuel costs. It is ironic that the specialized aggregates used as insulating materials to conserve energy cost so much more to produce due to the high proportion of energy consumed in their production. The first four parts of "Construction Materials" deal with the utilization of four major mineral aggregate types: Crushed Stone, Lightweight Aggregates, Sand and Gravel, and Slag. While the focus will be on the use of these industrial minerals and rocks, there will also be some coverage of sources, mining and production, especially in those cases where they are not discussed in the Commodity section of this book.

Jan 1, 1983