Search Documents

By E. T. Bowers

The Accident Analysis (ADA) computer program was developed at the Spokane Research Center (SRC) to provide a rapid broad-based analysis of mining accidents. Because the Bureau of Mines often needs this type of information for the development of viable research programs the ADA program was written to access and analyze accident data available frog the Labor Department's Mine Safety and Health Administration (MSHA). This report describes the ADA program, the data it uses, and the potential value it has for planning mining research.

Jan 1, 1987

By Danu Putra, Budi Sulistianto, Tri Karian, Mohammad Nur Heriawan

Stope layout optimization is an important feature of underground mining that maximizes the economic value of the project while taking mining limits into account. The large number of parameters and constraints makes it difficult to obtain the optimum condition. Several algorithms have been created to address these problems using a variety of methods. However, the circulating method has not explicitly included stope dimension stability analysis, resulting in a solution that is not stability-proven, which can result in a suboptimal solution. This study integrates the Mathews stability graph into the stope optimization algorithm so that the optimized stope layout considers stability conditions directly through an assessment of the available geomechanical data within the block model. The proposed algorithm is validated through a case study of a synthetic block model created by considering variations in grade and the geomechanical conditions of the rock. Furthermore, several scenarios are created to compare the performance of the algorithm that applies variations in stope sizes with the common case study of stope sizes that remain fixed. A more detailed assessment is also conducted on each final stope layout wall to ensure the successful application of stability analysis in the proposed algorithm through back analysis on the Mathews stability graph. The optimization results show that all walls in the final stope layout fall into the stable condition. Also, the proposed algorithm is also capable of maintaining the project’s economic value. Ultimately, the proposed algorithm can be deemed applicable and suitable for use in the initial stages of mining as a comprehensive assessment of the optimal stope layout, taking into account the stability conditions of the stope.

May 22, 2024

By R. W. Boyle

"EDITOR'S NOTEPart 1 of this paper, published in the August issue, covered lithochemical surveys based on major, minor and trace elements in whole-rock samples from primary enveloping halos.Part 2, which follows, continues with discussions of surveys based on leakage halos, zonation of elements, stable and radioactive isotopic distributions, and geothermometric, geobarometric, thermoluminiscent, pedochemical, hydro-chemical, atmochemical and biogeochemical methods. It concludes with a selected bibliography.Surveys Utilizing Leakage HalosLeakage halos can be used as scalar or vector quantities in thesearch for deeply buried blind mineral deposits. In the first case, the occurrence of a leakage halo (e.g. a small pitchblende seam) may simply indicate the possible presence of pitchblende mineralization or orebodies; in the second case, the areal or three-dimensional distribution of leakage halos may, by their increasing frequency and I or increasing metallic or gangue element content, provide a means of vectoring in on loci of mineralization and orebodies. Examples of both cases are given in the following text.Leakage halos are of many types, as shown in Figure 2 (Part 1), and are best discussed with respect to their associated mineral deposits. Furthermore, it should be noted that leakage halos are frequently offshoots or extensions of enveloping halos. Where this occurs, careful tracing of the leakage halo(s) downward or upward respectively will often lead to the apex or nadir (bottom) of the enveloping halo(s) and ultimately to mineralization or ore."

Jan 1, 1982

[ ]

Jan 1, 2011

By G. Jalkanen

Parameter estimation of the inverse distance estimation algorithm is presented. The objective function to be minimized is a sum of squared cross validation errors. The unknowns to be estimated are the exponent of the inverse distance estimator and anisotropic angles and ratios that are used in determining the distances in the algorithm. Examples are presented for both two and three dimensions data sets.

Jan 1, 2009

By Barry W. Klein

The U.S. economy was considerably stronger in 1976 than in 1974 or 1975. Real gross national product (GNP) rose sharply in the first quarter of 1976 and then increased at a more moderate rate for the remainder of the year. The unemployment rate fell until June and then increased for moat of the remainder of the year, finishing at the same rate as it had started the year. The inflation rate continued to decline in 1976. Reasons for the relatively low rate (compared with those of 1974 and 1975) included small increases in food prices and only moderate increases in energy prices. Total U.S. output measured in terms of GNP increased 11.6% in 1976. Real GNP in 1972 constant dollars rose 6.2%. Inflation as measured by the implicit price deflator increased 5.1%. In real terms, gross private domestic investment for residential structures rose 22.7% in 1976 after declining 14.7%a in 1975; State and local Government expenditures increased 1.4% in 1976; and personal consumption expenditures for services rose 4.5%. The Federal Reserve Board (FRB) index of industrial production increased 10.2%.

Jan 1, 1978

Mr G. Maude was educated at Huish's Grammar School (Taunton) and Leeds University. He graduated in 1961 with a B.Sc. degree in Mining. Mr E.B. Crocker was educated at Florida Park High School, Witwatersrand Technical College, and the University of the Witwatersrand.

Jan 1, 1985

By A. Güngör, Ü. Atalay

Thermal treatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The assistance of thermal pretreatment prior to grinding by microwave heating is scrutinized in this study. For this purpose three copper ore samples with different chemical composition were used. To see the effect of microwave heating on ore; work index, breakage rate and breakage distribution functions of original and heat treated samples were examined. The results obtained in this study did not show significant improvement in the grindability characteristics of the studied ores with microwave heat treatment. The inadequate amount of microwave transparent matrix was the main reason for the absence of cracks and micro-fractures in the microwave heated copper samples.

Jan 1, 1999

By Carl R. Peterson

The Rapidex continuous spiral blast tunneling concept uses a spiral blast pattern that provides efficient slabbing action, continuous progression, and partial self-shielding. A lightly shielded tunneling machine using this concept stays at the face to provide continuous drill, load, shoot, and muck functions. Previous phases proved the effectiveness of the blast pattern in the White Pine Shale tested the design features of the shield and developed a remote loading and shooting capability using inductively initiated blasting caps and a pumpable slurry explosive. Phase IV assembled previously used front-end elements (drill, loading components, shield) on a used Joy loader chassis and added a mucking system television monitoring and remote control elements. Remote television monitored loading shooting and mucking were investigated. Difficulty was experienced in locating previously drilled blastholes near the bottom of the heading and even on the face. These holes often had to be considered as lost. Because of hydraulic system deficiencies and overall congestion of machine elements at the face mucking rates obtainable with remote television monitoring were low (on the order of 16 tons per hour). Performance was good enough to indicate improved rates if more space were available and if extreme thoroughness were not required. Because of the serious nature of the lost hole problem, a new explosive loading scheme was given a preliminary evaluation. The new scheme would require the explosive and the detonating charge to be loaded through the drill steel. If the necessary equipment modifications could he made and if safe, efficient operation were assured, the new scheme would alleviate some of the crowding at the face and would eliminate the lost hole problem.

Jan 1, 1978

This paper discusses some topical issues on the mining administration and legislation fields including:  1. Licensing û Administration and associated specialist functions including:Processing and volumes of mining privilege applicationsFuture organisation and possible decentralisationSpecialist staffFacilitiesGuide to the Mining Act 1971 2. Mining Amendment Act 1981 Transitional procedures 3. Planning Tribunal First hearing of objectionsPoints of principle resulted there from 4. Quarries and Tunnels Bill Currently before Parliament û implications for metallurgical mining

Jan 1, 1982

By Shuangsuo Yang

Based on field observations and physical modeling of simulated materials, the dynamic equilibrium principle on the whole interaction process between the surrounding rocks and support of large deformation roadways in coal mines has been developed. It explains the methods of forming the bolted strata and its changing load capacity with deformation. It also points out the factors and conditions for forming the bolted strata as follows: (1) many entries in coal mines are subject to large deformation. During their service life, it goes through the following process, elastic > plastic > fiacture > broken > loosening, etc. During this dynamic process, the mechanisms of supporting structure are changing and therefore the interaction between support and rocks experiences a process of dynamic equilibrium. Furthermore, the required supporting force for stabilizing the surrounding rocks shows overall decreasing trend; (2) the bolted strata is a special supporting structure consisting of bolt, rock skin protection devices and rock strata within the bolted horizon. As deformation increases, the supporting structure of the broken strata within the bolted horizon experiences a process of periodic change, from equilibrium > not equilibrium > equilibrium. Corresponding to this change, the supporting capacity of the bolted strata also fluctuates and gradually decreases; (3) under the bolted strata, the stability of a large deformation roadway is dynamic and step-wise; and (4) the formation of bolted strata, especially bolted broken strata depends on the existence of compressive force. Supporting the bolted strata is not constrained by the quality of the surrounding rocks. It has broad range of application.

Jan 1, 2005

By M. J. Ankeny, J. J. Forbes

Several sets of questions and answers on the fundamentals of first aid to the injured, based on the Manual of First-Aid Instruction of the United States Bureau of Mines, are now in use in various parts of the United States. Persons experienced in first-aid instruction believe that a standardized set of questions and answers will assist materially in preparing men for examin- ations conducted by the Bureau for first-aid certificates. Inquiries as to whether a set of standardized questions and answers is available have been made frequently by those training men for the Bureau of Mines examination for certificates. It is believed that the following list of 171 questions and answers com- piled directly from the manual will be useful to company officials and em- ployees who are engaged in cooperative first-aid training to qualify for Bureau of Mines certificates. The list may also be used by field men of the Bureau in training instructors preparatory to a cooperative training campaign and in examining classes or individuals for first-aid certificates. The page references in parentheses refer to pages in the Manual of First-Aid Instruction.

Oct 1, 1935

By W. H. Young

In response to increasing national energy requirements. highlighted by the continuing growth in demand for coal for the generation of electric power the output of bituminous coal and lignite in 1965 passed the 500-million-ton mark for the first time since 1956, thus emphasizing the steady up-ward trend from the recent low of 403 million tons in 1961. There were corresponding upward trends in consumption, exports mechanization, and productivity. Production.-The output of bituminous coal and lignite in the United States in 1965-512 million tons-was 5 percent greater than the 487 million tons produced in 1964. The gain was attributed largely to expanded consumption by the electric utilities, greater use at coke ovens, and an increase in exports.

Jan 1, 1967

By Bahram Sameit

Blast engineers have been taking advantage of image-based rock fragmentation analysis methods for the past three decades to estimate rock size distributions. These methods utilize a range of image segmentation techniques, from manual to fully-automated, to delineate the edges of rocks in images. Rock delineation results are then converted to physical rock sizes (and percentage passing curves) by scaling the image pixels to correspond to physical measurements. The size scaling process is critical for acquiring physical measurements, but specifc to the limitations of different applications. This article starts by presenting a shovel bucket-based fragmentation analysis system, where scaling is done using the known width of the shovel bucket within the image. It will then describe methods that use pictures captured by digital cameras with scaling reference objects in the view. Finally, the article presents a method that uses three-dimensional imaging to capture images without the need for scaling reference objects.

By Arthur Matzick

The oil shale from the Mahogany zone of the Green River formation in northwestern Colorado has the greatest potential in the United States for early utilization. A large reserve of adequately rich shale is available to support a sizable industry, and crushing of tremendous tonnages will be required if conventional processing methods are used. This report presents Bureau of Mines data on crushing experiments, physical properties, and related information for Colorado oil shale. Among the properties important to crushing are slab-forming tendency, resilience, slippery character of the richer grades, and heterogeneous nature of an average charge of Colorado oil shale.

Jan 1, 1960

By J. Hines

Traditionally, fuel oil or diesel was the collector of choice in coal flotation, but in recent years these materials have come under increased scrutiny because of concerns about the toxicity of some components. In response to these concerns, Georgia-Pacific Chemicals LLC has commercialized a patent pending coal collector (Talon® 9400 reagent) that is 100% derived from the pulping of trees. This study presents a comparison of yields and recoveries for different coal collectors, including the one derived from the pulping of trees.

Jan 1, 2011

By Shu Yan

The high resolution resistivity method (HRRM) is developed specifically for detecting underground cavities and tunnels. HRRM has a special feature in that it can recognize and cancel static shift, which makes it different &om the high density resistivity method (HDRM). In searching for various means for detecting underground cavities, we found that the detecting depth of the transient electromagnetic field method (EM) depends mainly on the measurement duration, not the loop area. In addition, TEM can also be used to locate the high-resistivity bodies. In order to use them for local working site conditions, we combine HRRM with TEM to become a combined electromagnetic method. Since the late 1980's this method has been used to locate abandoned mines and air passages and burning centers of mine fires with great success. This paper cites case studies for which this technique was successfully used.

Jan 1, 2005

By R. Owen

An overwhelming amount of data can be collected around the blasting process. This information can include blasting product, pattern design, blast results, and routing. It is only when these data sources are combined in a concise and accurate form that they are of real use in determining the safety and economic implications of each parameter. Two key technological aspects of blasting are drill fleet management (DFM) and size fraction analysis (SFA). As these technologies are integrated as near-real-time measurement and QA/QC tools, the resolution and realization of blasting parameters is significantly increased. The Freeport-McMoRan Morenci Mine has integrated these technologies along with other existing database structures to create a responsive and sustainable tool for reconciliation, forecasting and parameter matching. This ability allows Morenci to customize blast patterns to meet the criteria most critical to each shot, whether the impact is influenced by routing and recovery, equipment maintenance or safety concerns. DRILL FLEET MANAGEMENT The current DFM was stabilized in its current form in mid 2009 after database and hardware maintenance met stability requirements. Currently the system is running on 12 production drills. The system receives pattern layout and is capable of semi-autonomous drilling over the entire district. The fleet is capable of drilling in highly altered intrusive units and hard granites through the range of sedimentary and volcanic units that comprise the Morenci District. The system brings a level of accuracy not achievable with earlier paint-marked patterns. Depth control is also increased along with more consistent wear and maintenance patterns due to semi-autonomous drilling.

Jan 1, 2011

By J. Schenck

Goldcorp Inc. has mining operations and exploration projects throughout Canada, the United States, Mexico, Guatemala and Honduras; as well as partnerships in Argentina and the Dominican Republic. In rural areas of developing countries it is very common to have mining operations surrounded by diverse communities consisting of people with limited, or no formal education. This is fertile ground for anti-mining NGOs to cultivate. The limited educational backgrounds of the people, coupled with a company desire to maintain a low profile can lead to a problematic lack of trust between the local communities and the mining company. As part of its commitment to environmental stewardship and sustainable development, Goldcorp has implemented various programs to build trust at these operations, as well as incorporating this policy into any new projects prior to commencement of operations. This paper is intended to describe two initiatives that have shown positive results for both the communities and the Marlin Mine.

Jan 1, 2009