Search Documents

By D. Kozelj

Introduction The porphyry copper deposit “Borska Reka” is the biggest undeveloped deposit in the Timok Magmatic Complex (TMC). Total reserve calculated manually is 611 Mt (cut-off grade 0.3% Cu) of 0.62% Cu, 0.21 g/t Au and 1.81 g/t Ag and 869 Mt of 0.58% Cu, 0.14 g/t Au and 1.11 g/t Ag using software. But since several deep drill holes are suspended in high grade (0.7% Cu) porphyry, total reserves could exceed 1Gt. The massive sulfide is also detected in the central (12 m at 4% Cu) and the bottom of porphyry style. Deposit was discovered during geologic exploration of deeper part of the Bor copper and gold deposit, i.e. area of high sulfidation with dominant massive sulfides. During exploitation of massive sulfide, constant explorations were carried out aimed at the expansion of reserve and discovery of new ore bodies. In that way, porphyry copper mineralization was discovered without knowing in the beginning that it was different mineralization type in regard to the ones that had been already identified and exploited. Vertical extension of porphyry is 0 m up to -1000 m sea level and not contoured along plunge. In the very beginning (1976), the exploration was focused on the shallow part of porphyry. That is because block caving method of massive underground mining was not developed at that time. Up to 1999, most of activity was related to underground exploration up to level -395 m. Geographic position The Bor deposit is located close to the industrial and University town Bor, which has over 50,000 inhabitants (census made in the year 2002). Apart from the Bor Mines, industrial complex of Mining & Smelting Basin Bor (RTB) comprises also a copper smelter (installed capacity up to 160,000 tons of blister copper) and tank house, copper wire factory, copper tube factory etc. Currently, RTB Bor is under privatization process that is going to be completed by the end of 2006. Up to date, over 20 companies have bought tender documentation.

Jan 1, 2007

The purpose of this paper is to cover in a general way the extent, geology, quality of product, working methods and trials of the coal mining industry. of New South Wales from 1946 to the present day, with particular reference to the Western field.It must be clearly understood that any opinions expressed are those of the author and not necessarily those of the Joint Coal Board.The extent of the Western coal field at the present stage of investigation may be said to be from a few miles east of Katoomha to a few miles north-west of the township of Ulan, the total distance being 150 miles.To the west of a line from the Western Highway from Lithgow through Wallerawang, PortIand, Tyldesley, Ben Bullen, Kandos and Rylstone, there are no signs of coal except for one or two outiiers in the neighbourhood of Portland. To the east of this line the coal-bearing areas extend to the seaboard approximately 80 miles to the east.GEOLOGY AND CHARACTERISTICS OF THE COAL SEAMSThe Western coal measures belong to the Upper or Newcastle series, which have been correlated with the Sciritheru or lllawarra, and the North-western or Gunnedah measures. Being close to the margin of the coal basin the Western measures have an average thickness of only 200 ft. to 500 ft., or approximately one-half of the maximum development of the Newcastle measures. They are underlain by Upper Marine beds which in turn rest directly on Devonian rocks.

Jan 1, 1954

THIS has been a much-neglected branch of engineering. With the majority of industries labour is the chief item of trouble and expense. Anything that will reduce trouble and increase efficiency is well worth considering. It is only of recent years that any attempt has been made on a scientific basis to improve conditions sporadic attempts having been made from time to time, privately and by law. Some have been successful, others unsuccessful not necessarily the fault of those who initiated the ideas, though naturally mistakes were made in some cases for want of experience, but those whom it was desired to benefit were not always prepared for the change, and by their distrust hampered schemes instead of assisting them.Man power is generally more expensive than machinery, though there are exceptions, such as when a small amount of work has to be done in a place where machinery does not exist, and it would not pay to instal any or where labour is cheap, and skilled workmen are scarce as in some tropical countries. When machinery is first introduced it generally causes the suspicion that it will deprive men of their work. It may cause men to vary the conditions of their work, and in some individual cases, when men are unable to conform to changed circumstances it may result in a certain amount of hardship; but, after all, the less competent must not hold back progress for the general good. Besides, changes as a rule do not take place suddenly, so old hands can generally find work at their particular calling 'till nature requires them to retire. In cases where men take to machinery, they not only find that they are relieved of the...

Jan 1, 1918

By Boden A

A procedure was developed for recovering metal values from copper-smelter fume. The fume is first leached to neutrality with dilute sulphuric acid to obtain a solution of zinc sulphate containing a low level of impurities. The tailings from this leach are treated with hydrochloric acid in two stages, in which tin and zinc are quantitatively leached and recovered as a tin concentrate and a zinc sulphatelzinc chloride solution.About 80 per cent of the lead sulphate is converted into lead chloride, which can be recovered as a pure product.Data on the effect of temperature, acid concentration, aeration, and solid/liquid ratios on the hydrochloric acid leach are presented, and the fate of the most important metals during the recovery process is described. Alternative treatments of the tailings from the neutral sulphuric acid leach were briefly investigated.

Jan 1, 1977

By T. M. Tharp

Attempts to analyze the stability of slopes, foundations and underground openings in discontinuously jointed rock have generally assumed full joint continuity or ignored the role of stress concentration at the tips of discontinuous joints. The most common approach in rock slopes is to consider a failure plane consisting of coplanar, but discontinuous joints separated by intact rock. The intact rock is assumed to fail in shear as a MohrCoulomb material and to contribute a strength component proportional to the fraction of the failure plane that is intact rock (Jennings, 1970). An alternative approach by Stimpson (1978) applies Lajtai's (1969) theory for shear strength of discontinuously jointed rock masses to slopes. Lajtai allows tensile failure in the intact rock of a composite surface. This theory yields lower shear strength than that of Jennings (1970) except in the presence of high normal compression, however it also fails to account for the stress concentration at the tip of a discontinuous joint. For a given slope geometry, stresses increase with slope height, but in both of these models rock mass strength is independent of size. A fracture mechanics analysis shows that particularly for small slopes, rock mass strength decreases with size.A continuous stepped failure surface produced by propagation of preexisting joints may develop at lower shear stress than pre¬dicted by the Jennings (1970) or Lajtai (1969) models. This fracture mechanics model applied to slopes in competent rock is more realistic in its assumed failure mechanism, and for large slopes more conservative than the Jennings (1970) or Lajtai models (1969).

Jan 1, 1984

The application of biogeochemical methods in mineral exploration in semi-arid to arid environments in Western Australia has been investigated in an area near Norseman.The study involved a comparison of trace element characteristics of rock, soil and plants in the vicinity of the Pioneer BB prospect, where nickel-iron sulphide mineralization occurs in a "greenstone" sequence of ultrabasic, basic and sedimentary rocks.Analyses of unweathered and partly weathered rock from diamond drill cores show the ultrabasic rock to be highly variable with respect to Ni, Cu, Co, Zn and Mn.Samples of weathered bedrock and overlying soil were analysed for total trace element contents and for the trace elements associated with secondary iron and manganese oxides. Approximately 30 per cent of the total nickel content of the weathered basic rock is associated with secondary iron and manganese oxides, compared with approximately 15 per cent in the weathered ultrabasic rock.The soil has a sufficient residual content to provide a reliable indication of the chemistry of the underlying rock. Total trace element analyses of the -89 mesh fraction show strong anomalies for nickel and copper over the mineralized zone. Important amounts of nickel, cobalt and, to a lesser extent, copper are apparently associated with secondary iron and manganese oxides in the soil.Melaleuca sheathiana (tea tree) has been used to study the relationship between soil and plant chemistry. No strong relationship between plant and rock type was observed. Analyses were made of leaves, twigs, wood, bark and roots, and all plant organs were found to have anomalous nickel and copper contents near the mineralized zone. Leaves were found to give the best contrast in the anomalous area and to show fewer erratic values than other organs. It is concluded that the uptake of trace elements by tea tree is low in the semi-arid to arid environment of Western Australia, but that analyses of the plants do reflect the presence of mineralization.

Jan 1, 1973

By Floyd D. Varley

Outbursts, the sudden and violent out- pouring of material into mine openings, is a ground control problem increasingly encountered in the United States as deeper seams are developed. Outbursts, caused by several mechanisms, are the result of the loading of ground support systems be- yond their designed capacity to failure, manifested in a violent release of stored energy. There are several types of outbursts typical to deep underground coal mines. - Outbursts of the coal face due to the presence of pressure abutments in close proximity to the face. These outbursts are usually accompanied by liberation of large amounts of methane. - Instantaneous convergence of the ribs and floor due to overloading and failure of ribs which lengthens the beam of floor strata sometimes resulting in a chain reaction failure of the mine floor. - violent failure of the confined core of a pillar due to rapid loading beyond the yield point of the pillar.

Jan 1, 1986

Jan 1, 1971

By S. J. Lötter, J. T. Nel, W. Purcell

"SynopsisGlow discharge optical emission spectroscopy (GD-OES) is an analytical technique used in the analysis of solid, conducting materials. Though primarily of interest as a depth profiling technique on samples with varying layers of both conducting and non-conducting materials, it is also capable of rapid bulk analysis of homogenous, solid samples. GD-OES combines the advantages of ICP-OES (wide detection range, speed, and lack of interferences) with the solid sampling of XRF techniques. This allows the analyst to not only quantify the elemental composition of a sample, but to evaluate it in terms of homogeneity with depth, a field in which auger electron spectroscopy (AES) and secondary ion mass spectrometry (SIMS) have traditionally been the primary techniques. Although GD-OES does not replace these useful techniques, it does offer various advantages over them, making it an excellent complementary analytical tool.In GD-OES analysis, a low-pressure glow discharge plasma is generated with the sample material acting as a cathode, accelerating the cations in the plasma towards the sample surface. This bombardment causes the sample material to ‘sputter’, essentially knocking free atoms or molecules of analyte material, which are then drawn into the plasma where they are excited. The light emitted by this excitation is then diffracted to separate the wavelengths emitted by the specific elements and detected by a spectrophotometer. The intensity of the signal is directly proportional to the quantity of analyte element present in the sample, allowing simple calibration and quantitative determination of the elements. Technological improvements made in the past twenty years or so have significantly increased the usefulness of GD-OES for surface analysis. Faster plasma stabilization and start-up allow for the quantification of surface layers as thin as 1 nm. Sputter rates have been accurately measured for many common materials, allowing them to be built into software libraries in the instrument’s control software. This dramatically expands the usefulness of this software and the ease of performing analyses.GD-OES analysis of nuclear materials allows for the rapid determination of the elemental composition without the requirement of initial dissolution. The thickness of any corrosion layers on nuclear materials can also be determined."

Jan 1, 2015

By L. Adler

Two basic cases involved in the design of an opening in bedded rock are: 1) where the beds deflect from each other so as to be separated; and 2) where the beds deflect onto their lower neighbor, loading the latter while reducing their own load. Analysis of case 1 is relatively simple, while the interference of the original deflection curves in case 2 complicates analysis of the latter. Figures and formulae are presented for determination of interference loading in this situation. The design of an opening in bedded rock involves two basic alternatives.1'2 In one case the beds deflect away from each other, so as to be separated from their neighbors; in the other case the beds deflect onto their lower neighbor, loading it, while reducing their own load. This is shown in Fig. 1. The first case lends itself to a simple analysis, since the upper and lower boundaries of each beam remain a free surface. In the latter case, however, due to the interference of original deflection curves, the analysis is more complex. Earlier investigators of this interference problem solved it by making the tacit assumption that this type of loading was uniformly distributed along the beam's length. While there is no intuitive justification for this assumption, its use does lead to an approximate solution. Still, a more exact solution does not require this apparently unrealistic restriction. To achieve initial simplicity, the analysis will at first be limited to a two-bedded sequence, as in Fig. 2. Since both beams have identical end conditions and spans, the original deflections of their center lines are members of the same family of curves, as shown in Fig. 3. Therefore, if interference occurs at one point along their center lines, it will occur at every point. For convenience, the midspan point is that usually examined. Deflection at midspan for a uniformly loaded beam regardless of end conditions is: where c is a constant depending on end conditions; w is the body load and equals yh, lb per ft; y is the specific weight of rock, lb per ft'; L is the span, ft; E is Young's Modulus, lb per ft2; I is moment of inertia (for a rectangular section), I = bh3/12 = h3/12, (ft4); b is the width of beam and equals one; and h is the thickness of beam, ft; or 3U > yB an Substituting the appropriate values into Eq. lb, interference between the two beds can be predicted. Should it occur, the additional loads along the lower boundary of the upper bed and the upper boundary of the lower bed must be determined. From the principle of action and reaction, these added loads are known to be equal and opposite, as indicated in Fig. 4. Since the final deflection curves for both beds are identical (Fig. 3), their successive derivatives of y with respect tox must also be identical. That is:

Jan 1, 1961

By Swapan Bhattacharya

United States federal and state regulatory authorities require underground mine operators to adopt adequate measures to minimize material damage to the surface caused by nine subsidence. This paper presents an approach to define and determine the extent of material damage due to subsidence from underground coal mining. The basic steps involved in the development of adequate criteria have been enumerated together with the approaches and methodologies used.

Jan 1, 1984

By Peeler P. K

The recent renewal of interest in hydrometallurgical routes for copper production has been brought about by the possible future reliance on mixed ores and lower grade deposits, environmental aspects, and energy considerations.A number of hydrometallurgical processes for the recovery of copper have recently been proposed. Flowsheets are developed for two processes which incorporate several treatment methods being experimentally studied in Australia.In the first process a cupric chloride leach is followed by electrowinning whilst the second is based on the formation of cuprous ions, stabuized by acetonitrile and subsequent disproportionation to cupric ions and metallic copper. For the purpose of comparison, flowsheets were also developed for the Arbiter and Cymet processes.Process economics are estimated for the four processes and the results are discussed in relation to competitive pyrometallurgy. None of the four hydrometallurgical processes, with possible exception of the Cymet process, appears to be competitive with established large scale and newly developed pyrometallurgical processes for chalcopyrite.However, because the economics of the individual hydrometallurgical processes depend strongly on specific conditions, a "tailored" process may be competitive with pyrometallurgy in particular circumstances.

Jan 1, 1977

By R. Kanniganti

The primary problems of pillar design in seams subject to interaction are due not only to difficulties in predicting loading, but also to the often unsymmetrical nature of the stress fields. The effects of uneven stress fields on failure patterns within a pillar were studied wing a two dimensional finite element method. Lower seams, including ultra- close mining situations were evaluated considering conventional pillars. Pillar case study data for under mining were analyzed to determine if empirical trends in stable pillar sizing could be derived. Recommendations for multi-seam pillar design are made, based on anticipated loading conditions within a pressure bulb. Applications of the research results are demonstrated using case studies

Jan 1, 1995

By G. F. Butterworth

The metallographic structures most frequently encountered in rifle barrels, and which are illustrated by the accompanying photomicrographs, fall naturally into two groups, distinguished by the method used to, produce in the stock a physical condition having the requisite properties. The fist group consists of "rolled" barrels; that is, barrels subjected to hot working by rolling in or near the critical range. In the second group, the stock, which is smaller in diameter than the first, is upset to form the butt end and is then heat treated by giving it a quench and a draw. These barrels will be referred to as " heat-treated " barrels. The structure of the rolled barrels resembles closely that of the same steel after annealing. There is the same network of excess ferrite outlining the grain boundaries, but the grains themselves are composed of sorbite rather than pearlite. The grain size is closely related to the rolling temperature. The critical-point curves of this grade of steel, which is approximately 0.50 to 0.60 per cent. of carbon and 1.00 to 1.30 per cent, of manganese, show a single very pronounced point between 1300" and 1350" F. (704" and 732" C.). Barrels rolled within this temperature range give an exceedingly fine grain, shown in Fig. 1. In fact, the grains may be so fine that, at a low magnification, they may be confused with the heat-treated structure shown in Fig. 6. A magnification of 500 diameters, however, will always resolve a rolled barrel into the characteristic structure shown in Fig. 2. As the temperature is increased, the grains are found to be larger. If, on the other hand, the rolling temperature is below the critical range, the structure previous to rolling will not be obliterated, the only effect of rolling being to elongate the coarse sorbite grains in the direction of rolling, Fig. 3. This distortion is greatest at the muzzle. Heat-treated barrels are quenched in oil from above the critical range, which should give a martensitic structure, Fig. 4, but the presence of some troostite in the martensite is frequently noted when the quench has not been sufficiently drastic, Fig. 5. The structure brought about by the subsequent draw is not so striking, though quite as typical. It is sorbitic or sorbito-pearlitic, and under a low magnification appears almost homogeneous, as in the case of fine grains of pepper and salt well mixed together, Fig. 6. This structure is substantially the same for all

Jan 1, 1920

By Joe F. T. Agapito

High stresses and adverse geology in deep coal mines in the state of Utah, USA, have caused numerous bumps. The larger bumps have been associated with seismic events with Richter magnitudes of 3.6 and greater, and in some cases have filled openings for lengths of 150 m. A better understanding of the mechanisms and stress levels involved in bumping is needed to help develop improved stress control design and bump mitigation methods. The geology of the area is notoriously bump-prone. The coal has poorly developed cleating and occurs in multiple seams that are often bounded by very strong roof and floor sandstone/siltstone beds. The overburden is formed by thick, competent strata with numerous sandstone channels This geology and deep cover are the major source of high stresses, causing bumps. This paper evaluates live common stress factors responsible for bump problems: depth, sandstone channels, arching, faults, and coal thickness. It uses ease study data from longwall panels with two-entry/yield pillar systems typical of deeper Utah mines. Results illustrate the importance of analyzing stress factor experience to allow a better understanding of the problem.

Jan 1, 2000

llmenite from the west coast of the South Island, New Zealand, shows exceptional reactivity with dilute sulphuric acid. Based on this, a cyclic acid leaching process was developed for the production of material with more than 98% TiO2, suitable as a substitute for mineral rutile.Titanium hydrate is recovered from the leach liquor by hydrolysis, and is calcined to give the required product.Ferrous sulphate is crystallized from the hydrolysis filtrates, which after concentration are returned to the leaching stage. The need for further evaluation of the process on a larger scale is indicated.

Jan 1, 1973

By A. N. Holden, W. E. Seymour

DURING the last several years, the U-Zr system has been studied at many laboratories as one of the research programs sponsored by the Atomic Energy Commission. The equilibria in part of this system have been difficult to determine, although the phase diagram from 0 to 60 atomic pct Zr has been established with reasonable certainty. Existing diagrams of the system vary appreciably beyond 60 atomic pct Zr, particularly with regard to the existence of an intermediate phase. Most existing diagrams show a transformation or reaction horizontal near 600°C. In 1955, a collection of uranium phase diagrams' was prepared at the Battelle Memorial Institute and the U-Zr diagram in that collection contained a questionable region in the vicinity of 60 to 80 atomic pct Zr. Summer-Smith" has published a phase diagram of the system that shows no intermediate phase. Summer-Smith did his work with powders and found only the uranium and zirconium eutectoid mixture from X-ray patterns of material annealed below 600°C. Mueller3 at Argonne National Laboratory did similar work with filings, and he found that initially there was a pattern of an intermediate phase, but on long-time annealing

Jan 1, 1957

By Mark A. Jirsa

The Biwabik Iron Formation is a ~1.9 billion year-old sequence of iron-rich sedimentary rocks that was metamorphosed at its eastern- most extent by ~1.1 billion year-old intrusions of the Duluth Complex. The metamorphic recrystallization of iron-formation locally produced iron-rich amphiboles and other fibrous iron-silicate minerals. The presence of these minerals in iron-formation along the eastern part of what is known as the Mesabi Iron Range, and their potential liberation by iron mining has raised environmental health concerns. We describe here the geologic setting and mineralogic composition of the Biwabik Iron Formation in and adjacent to the contact metamorphic aureole of the Duluth Complex. The effects of metamorphism are most pronounced within a few kilometers of the contact, and decrease progressively away from it. The contact aureole has been divided into four metamorphic zones?each characterized by the composition and crystal structure of the metamorphic minerals it contains. The recrystallization of iron-formation to iron-rich amphibole minerals (grunerite and cummingtonite) and iron-pyroxene minerals (hedenbergite and ferrohypersthene) is best developed in zones that are most proximal to the Duluth Complex contact. ©2007 Elsevier Inc. All rights reserved. Keywords: Iron-formation; Mining; Fibrous; Mineralogy; Metamorphism.

Jan 1, 2007

By D. W. Nel

Nanofiltration (NF) has attracted much attention over the past few years due to the reduced energy consumption compared to reverse osmosis (RO) and better separation performance compared to ultrafiltration (UF). Although research has been done in the area of NF of nickel ions, sodium ions, and acid separation, not much attention has been given to the separation of high nickel concen¬trations from sulphuric acid streams. The use of NF for the separation of nickel and acid from a spent nickel electrolyte is an innovative process alternative for future industrial application within a base metal refinery. In this study, the separation performance of a composite polyamide NF membrane on a spent nickel electrolyte was investigated by varying the sodium sulphate concentration in the feed (50-150 g/l), the trans-membrane pressure (35-55 bar), and cross-flow velocity (1.5-3.5 m/s), and measuring quantities such as total permeate flux, acid rejection, nickel rejection, and sodium rejection. The nickel and acid concentration in the feed were kept constant with variations between 40-60 g/l and 25-40 g/l respectively, while the temperature of the experiments was kept constant at 50°C. The membrane was found to be very selective for nickel ions, with the rejection of nickel ions varying between 54.4% and 98.2%. The rejection of acid ions varied between -5.9% and 21.8%. The rejection of sodium ions varied between 16.6% and 72.4% at a cross-flow velocity of 2.5 m/s and sodium sulphate concentration of 50 g/l in the feed solution. An increase in trans-membrane pressure increased the rejection of nickel, sodium, and acid ions, while an increase in sodium sulphate concentration decreased the rejection of nickel and acid ions. The total permeate flux was found to increase with an increase in trans-membrane pressure and decrease with an increase in sodium sulphate concentration. The cross-flow velocity had an insignificant effect on the total permeate flux and the rejection of nickel, sodium and acid ions.

Jan 1, 2013

GOLD has played a part in the development of Australia. The total yield exceeds SIX hundred million pounds sterling, while the glamour of gold-mining and the unfailing demand for the product have enhanced its influence. The production is still considerable, but the yield is less than one-quarter of that twenty years previously, while the number of men employed has dropped from 70,000 to 11,000. Not only has there been a marked decline in production, but it is anticipated that thisdecline will continue, and continue more markedly. It is therefore desirable to ascertain the causes of the decline and inquire into means for diminishing or preventing it.The problem under discussion is far from being only local. Finlay states: The grand feature of the history of the business has been the progress of an economic cycle unfavourable to gold milling. The USA yield fell from $101,000,000 to $44,000,000.South Afriea has for some time produced one-half of the world's gold; yet in the Mining and Scientific Press of 11th February, IH22, General Smuts is quoted as saying that if the premium disappeared entirely 24 out of 34 mines would shut down. The solution, however, might be either general eg, a great advance in the metallurgy of gold; or local eg, a bonus; but before discussing any of the proposed solutions it will be advantageous to review the situation.STATISTICS OF THE PAST AND PRESENT PRODUCTION OF THE WORLD AND OF AUSTRALIAThe inquirer soon finds that there is a good deal of uncertainty, and that much care is needed in collating figures. In some cases a considerable part of the output is not officially reported, and returns...

Jan 1, 1924