Search Documents

By Hargraves A. J

With increasing depth, stresses and stress phenomena are becoming more important considerations in Australian coal mining.A large number of compressive and tensile strength tests was made on coal and rock cubes cut from samples taken in various Australian collieries. In addition, an empirical impact strength test was carriedout on fragments of the same samples, to obtain a correlation with compressive strength.In one colliery, flat-jack measurements were taken to assess stresses in coal ribs and in the roof.INTRODUCTIONBy world standards, some of the New South Wales collieries are approaching depths of cover considered a maximum for bord and pillar the normal Australian coal mining method. Several South Coast collieries are winning coal at depths of about 1500 ft., and future operations are being planned at deeper cover. Some areas of these deep workings produce considerable quantities of seam gas.Phenomena associated with high stress and copious gas under pressure in the seam violent phenoma presenting a danger and a nuisance in mine working - have occasionally occurred, and the phenomena are being investigated as a whole (Hargraves, 1958), and separately as a gas problem (Bolt and Innes, 1959; Hargraves, 1962) and as a stress problem. This paper relates to the latter - to investigations into the strengths of coals and coal measure rocks, and into the stresses in and about coal seams...

Jan 1, 1962

By D. M. Mubita

Dilution reduction is one of the areas that offer metal mines an opportunity to increase revenue and reduce costs, resulting in enhanced profits. Effective dilution control programmes require interaction on a multi-disciplinary level. This paper outlines recent initiatives undertaken at Konkola Mine to reduce dilution and increase revenue. The increase in revenue arising from reduced dilution and high factors between in situ and delivered to mill grades were quantified and amount to close to U$ 1.0 million per one per cent improvement in grade factor at a 75c/lb copper price. Sources of dilution from open and in?stope mining methods practised at the mine were identified and a multi-disciplinary dilution control forum set up to control these. Among the major achievements were the introduction of low dilution in-stope mining methods; the introduction of Gemcom geological and mining planning software to replace traditional pencil and paper methods, leading to better in situ estimation and production planning; enhanced control in open stopes through dilution awareness among mining production personnel; location of critical secondary development ends in correct positions; enhanced blast hole control; tracking of development waste by metal tracers and monthly tally; implementation of a cavity monitoring system to check over-breaks in open stopes; and setting up of a stope history database. The results from the cavity monitoring system showed that stopes with over-breaks of 5 metres or less could be controlled to break along the hangingwall contact.

Jan 1, 2005

By J. Brasfield

Jim Walter Resources, along with the Rock Mechanics Branch of British Coal and Strata Control Technology Pty. Ltd., is presently studying the yield-stable-yield pillar design in use at the Blue Creek No. 7 Mine located in Brookwood, Alabama. This paper describes the steps taken to determine stresses on the strata surrounding the pre-driven development entries. It also describes the installation and monitoring of stress cells and extensometers used to quantify the stress build-up and strata movement associated with the headgate pass of a longwall panel. The findings of this study will be used to design and predict the performance of a 2 entry yield pillar system in the Parkgate Seam at Welbeck Colliery in the United Kingdom. Stress measurements and strata movement data from No. 7 Mine and Welbeck will be used to develop a computer model that can predict the performance of such a pillar system in British mines. Jim Walter Resources will use this data to study the performance of the present yield-stable-yield pillar system in order to determine if conditions will allow the stable pillar width to be decreased while maintaining current standards of safety and production.

Jan 1, 1994

By T. M. Ruff

A prototype mucking machine designed to operate in narrow-vein stopes was developed by Foster- Miller, Inc., Waltham, MA, under contract with the U.S. Bureau of Mines. The machine, called a compact loader-trammer, or minimucker, was designed to replace slusher muckers in narrow-vein underground mines. The minimucker is a six-wheel-drive, skid-steered, load-haul-dump (LHD) machine that loads muck at the front with a novel slide-bucket system and ejects it out the rear so that the machine does not have to be turned around. To correct deficiencies of the tether-remote-control system, a computer-based, radio-remote-control system was retrofitted to the minimucker. Initial tests indicated a need to assist the operator in guiding the machine in narrow stopes. An automatic guidance system that used ultrasonic ranging sensors and a wall-following algorithm was installed. Additional tests in a simulated test stope showed that these changes improved the operation of the minimucker. The design and functions of the minimucker and its computer-based, remote-control system are reviewed, and an ultrasonic-sensor-based guidance system is described.

Jan 1, 1992

By John C. Machisak

INJURY and employment figures for nonmetal mines and mills in 1959 are presented in this publication. Data for nonmetal mines are presented separately from those for nonmetal mills. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry each year requesting their voluntary submission of injury experience and employment data. The voluntary response to these requests has contributed greatly toward the promotion of safety in the industry, and every effort has been made to make the information as complete as possible.

Jan 1, 1963

By John C. Machisak

INJURY and employment figures for nonmetal mines and mills in 1959 are presented in this publication. Data for nomnetal mines are presented separately from those for nonmetal mills. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry each year requesting their voluntary submission of injury experience and employment data. The voluntary response to these requests has contributed greatly toward the promotion of safety in the industry, and every effort has been made to make the information as complete as possible.

Jan 1, 1963

By A. B. Parsons

Jan 1, 1971

By George K. Schenck

This Bureau of Mines publication describes and evaluates a Standard Industrial Classification (SIC) based end-use data system for minerals that is designed to link the demand for minerals to economic activity in commercial uses. The new data system is two-dimensional. The first dimension of technical product classes (TPC's) measures the consumption of minerals in major primary intermediate products. The second dimension measures the consumption of these TPC's in SIC end-use sectors in sufficient detail to identify the major determinants of demand for each TPC. Intercomodity comparisons are achieved at the level of SIC two-digit major groups. The methodology was developed so that all available sources of information from Government and industry can be utilized at minimum cost. This information will be supplemented with additional data to be obtained by modifying existing Bureau of Mines canvasses so as to elicit additional quantitative responses from mineral producers. The new data system is expected to improve significantly the ability to forecast demand for minerals, and provide an information base that would, for the first time ever, permit resolution of such questions as trends in substitution among materials and the intensity-of-use of materials in end-use sectors. For the 42 TPC?s identified in the report, data are available for the new system from current sources or, except for three TPC?s that require new canvasses, can be obtained by modification of existing Bureau canvasses.

Jan 1, 1982

By Ned Baker

Details are given of a fuel-induction system for a hydrogen, fueled engine. The induction system was designed to preclude backfire otherwise common in hydrogen fueled engines. System features and test data are presented and discussed in the context of the requirements peculiar to use in an underground mine environment. The fuel induction-system when tested in conjunction with a modified Caterpillar 3304 engine provided backfire free engine operation and satisfactory engine performance.

Jan 1, 1982

By John G. Palmer

Continued development of an especially impregnated silica gel capable of reversible chemical detection of carbon monoxide (CO) was reported. The affects of changes in mine-related ambient conditions on the detection catalyst's response were explored. Temperature, humidity, and several interfering gases were found to affect the detection catalyst. The interferents include hydrogen sulfide, nitrogen dioxide, acetylene (and methylacetylene), and ammonia. High humidity decreased the detection catalyst's sensitivity to carbon monoxide for some formulations. Increasing temperature generally decreased the reaction time of the detection catalyst with carbon monoxide. Badges and carriers for the visual presentation of the detection catalyst were constructed. Several variations of these devices included provisions for absorbants and filtering agents which help protect the detection catalyst from gaseous interferents. A variety of catalyst support agents were tested in an effort to find the most suitable. Included were alumina, magnesium oxide, magnesium silicate, and several forms of silica gel. In addi tion to free-flowing forms of these sorbents, thin layer chromatography plates coated with cellulose, alumina, and silica gel and newly developed PTFE entrained silica gels were examined. A limited physical, chemical, and mechanistic characterization of the detection catalyst and the materials used to prepare it has been carried out. Metal component ratio studies, spectral, analytical, pH, and rate measurements were done.

Jan 1, 1982

By N. A. Eilertsen

This paper presents the results of intermittent study begun in 1956 by the Federal Bureau of Mines of yieldable steel arches and yieldable steel ring sets installed for support of development openings in metal mines. Observations were made of this type of support in several iron mines in the northeast and north-central states. The sets, both arches and rings fabricated in the United States, are made from a hot-rolled, cold bent, structural U-shaped steel section in two weights, 15 pounds and 21 pounds per foot. The lighter section is generally used, It is 4.41 square inches in cross section area, and the calculation is that a 6-foot length of this structural shape installed as a supporting column, will safely carry the same load as a Douglas fir post of the same length but of 22 times the cross-sectional area of the steel.

Jan 1, 1962

By N. R. Dixon

This report summarizes all work performed under U.S. Bureau of Mines Contract No. J0395028, "Noise Control of Rubber-Tired Front-End Loaders Used in Surface Mining. " Two loaders, a Caterpillar 988 and an International H-400B, were chosen for this program, and the noise sources and acoustic paths that contribute to the operator's noise exposure were identified. Retrofit noise control treatments were designed and installed on these loaders, and noise reductions of more than 10 dBA at the operator position were achieved on both machines. The retrofit packages are low cost and have been field tested in two mines for more than two years. The results of the program were communicated to the mining industry through a series of noise control workshops and a field manual. The workshops were given in nine states across the U.S. and more than 440 manuals were distributed An audio/visual slide presentation was also developed which the program.

Jan 1, 1983

By John R. Rhodes

The objective of this project was to investigate the feasibility of analytical techniques potentially capable of determination of Mg, Al, Si, S, Ca and Fe in 1 to 2 mg samples of respirable coal mine dust, in a total analysis time of not more than 10 minutes per sample, using equipment capable of being truck mounted for field-laboratory operation. It was not essential that the technique be non-destructive, but the chosen technique is, and this enables the analysis to be performed directly on the 37 mm diameter membrane filter on which the respirable dust sample is normally collected. The sensitivity requirements are therefore quoted in terms of the units of measurement, µg/cm2. The detection limit (3o of the background criterion) should be 0.5 µg/cm2 or less. The precision should be 5% or better, at concentrations above which the detection limit is not the determining factor.

Jan 1, 1972

By Sara Jane Boles

In recent years the interest in rare-earth compounds as refractory materials has exceeded the available literature on the subject. While some basic properties, such as density and melting point, of the more readily available rare-earth compounds have been reported in the literature, relatively few papers can be found that deal comprehensively and primarily with high-temperature refractory properties and applications of rare-earth oxides, carbides, sulfides, and nitrides. Therefore, this bibliography has been pre-pared for the use of the ceramic industry as a guide for locating and utilizing the scattered and frequently fragmentary information available. The term "rare earths", as applied in the literature search for this bibliography, is understood to include the following elements: cerium, dysprosium, erbium, europium, gadolinium, holmium, lanthanum, lutetium, neodymium, praseodymium, samarium, terbium, thorium, thulium, uranium, and ytterbium. (On the periodic chart, these elements appear as numbers 57 through 60, 62 through 71, 90, and 92.) It is emphasized that many of the abstracts included are from papers in which the rare-earth compound or compounds are treated along with several other ceramic materials, are mentioned only secondarily, with primary interest placed on a more commonly used refractory material, or are used as part of a mixture of materials formed experimentally and reported on in the paper. As the better known rare-earth materials, such as the oxides of uranium, thorium, and cerium, appear more frequently in the literature, they also appear more frequently in this collection. Articles abstracted include only information on the basic properties that are of interest to the refractories investigator. References to crystal lattices and related topics are generally excluded from this publication. The temperature 1,500° C. has been set arbitrarily as the lower limit for reported data on thermal properties. However, because of the scarcity of information, some reports are included in which data are limited to those obtained at lower temperatures. Many of the articles abstracted include lists of references that will be of additional assistance in pursuing specific lines of investigation.

Jan 1, 1962

By John C. Machisak

This publication, for the calendar year 1959, contains statistical data on injuries and employment pertinent to metal mines, ore-dressing plants, and primary nonferrous smelters, refineries, and reduction plants. The Bureau of ,Mines is authorized to request data on injuries and employment in the metal-mining industry, and the information, voluntarily submitted by the operators, contributes immeasurably to the promotion of safety in the metal- mining industry. Every effort has been made to make the annual canvass as complete as possible. The data presented are classified according to the hind of ore mined and includes information on copper, iron, lead-zinc, gold-silver lode, placer, uranium- vanadium, and miscellaneous metals. A breakdown of miscellaneous metals by commodity is shown in tables 17 and 18.

Jan 1, 1963

By John C. Machisak

This publication, for the calendar year 1959, contains statistical data on injuries and employment pertinent to metal mines, ore-dressing plants, and primary nonferrous smelters, refineries, and reduction plants. The Bureau of Mines is authorized to request data on injuries and employment in the metal-mining industry, and the information, voluntarily submitted by the operators, contributes immeasurably to the promotion of safety in the metal-mining industry. Every effort has been made to make the annual canvass as complete as possible. The data presented are classified according to the hind of ore mined and includes information on copper, iron, lead-zinc, gold-silver lode, placer, uranium- vanadium, and miscellaneous metals. A breakdown of miscellaneous metals by commodity is shown in tables 17 and 18.

Jan 1, 1963

By Terry S. Cory

This report covers magnetic field strength measurements vs range and frequency In low-medium coal mines. Both quasi-conductor-free and conductor-proximity areas were Investigated. The program covered 5 mines, 4 seams, 6 measurement sets, and 3 geographic areas, The results have been summarized In terms of maximum communication range expected per seam and noise condition. Scatter gain Is further explored as a simple measure of energy coupled to conductors.

Jan 1, 1978

[ ]

Jan 1, 1979

By M. A. Elliott

The technology of gasifying coal to produce synthesis and pipeline gas has advanced significantly in the Past 20 to 30 years. This period has seen the extensive use of oxygen in coal gasification, the development of suspension gasification processes and fluidized-bed gasifiers, the operation of various gasification processes at elevated pressures, and operation of gasifiers under slagging conditions. These developments are discussed, and their application to commercial and pilot plant gasifiers is reviewed. Typical processes for synthesis gas production are described, and operating results are compared. Pipeline or high-Btu gas may be produced from coal either by catalytic conversion of synthesis gas to methane, or by the direct reaction of coal with hydrogen (hydrogasification) to produce a methane-rich gas. Neither of these methods has been applied commercially, but developments pertaining to each of them are reviewed, and general processing schemes are discussed. The use of coal as a raw material for manufacturing gas has a long and distinguished history. In fact, the gas industry began in the early 1800's when William Murdock demonstrated that it was feasible to produce and distribute gas made by retorting coal. Coal was used exclusively for gas manufacture until the middle of the 19th centruy, when Lowe invented the carbureted water gas process. In that process, coke was one of the raw materials used, so coal was still an important factor in gas manufacture. However the availability and relatively low cost of natural gas in the United States, and its widespread distribution by long-distance pipelines in recent years, has virtually eliminated the use of coal as a raw material for gas manufacture in this country. It should not be inferred from the foregoing that the technology of coal gasification has remained static in the United States and abroad. In fact, in the past two decades many new concepts have been developed in both the science and the technology of gasification. This progress has been a result of the considerable expansion in research on the fundamental chemistry and physics of gasification reactions, and in development work on gasification processes. This expansion in effort stems in part from increased interest in the use of gas as a raw material for the synthesis of chemicals and liquid fuels, and in part from the need to develop methods for gasifying coal and other solid fossil fuels to ensure a long-range supply of energy in the form of gaseous fuel. In these uses of gas, synthesis gas, a mixture of hydrogen and carbon monoxide in various proportions, is the starting material. It may be converted catalytically to gaseous and liquid hydrocarbons and other chemicals, or to hydrogen for use in hydrogenation or reduction reactions. Since coal is our most abundant fossil fuel, it is inevitable that one day it will regain its prominence as a raw material for gas manufacture. It is of interest, therefore, to consider the present status of gasification technology, directing attention particularly to advances made in recent years. Inasmuch as many comprehensive treatises l-3 and review4-7 of gasification technology are available, no attempt will be made in the present review to cover all processes in detail. Instead, the discussion will be concerned chiefly with typical processes embodying the advances that are most likely to be generally applied. ADVANCES IN GASIFICATION TECHNOLOGY For purposes of this discussion the starting point will be the conventional processes that were used for many years for the complete gasification of coal. These were: 1) carbonization in coke ovens followed by gasification of coke with air and steam in cyclic water-gas generators, and 2) fixed-bed air-blown producers. Both of these methods have obvious deficiencies when we consider that the ideal complete gasification process would be a single-stage, continuous

Jan 1, 1961

By L. Salnais

"Aluminum alloy structural components f or aircraft designed prior to the early 1970s, were machined from 2024, 7075 and 7079 plate, bar and forgings in either the T3xxx of the T6xxx tempers. Protective treatments for these parts consisted of chromic acid anodizing and alkyd zinc chromate primer, plus a nitrocellulose lacquer for exterior parts.The major service problem with these parts was the frequent occurrence of exfoliation corrosion and stress corrosion cracking (S. C. C.). Therefore, 2024 and 7079 alloys, with min or exceptions, were not used in aircraft designed after the early 1970s. Replacement materials were 7075 and 7050 alloys in the overaged, exfoliation corrosion and S. C. C. resistant, T73xxx tempers.The use of improved materials together with the upgrading to chromated epoxy primers, polyurethane enamels and the introduction of water displacing corrosion inhibiting compounds have significantly reduced corrosion in aircraft. IntroductionThe prevention of corrosion in aircraft has been a challenge to aircraft designers for many decades. With the design of the first all-metal aircraft, the designer and builder were thrust into the relatively new field of protective treatments as corrosion started to become more prevalent. This resulted from the continually increasing importance and wider utilization of aircraft, and their exposure to a wider variety of ho stile environments such as urban industrial pollution, high humidity tropical areas and salt ladened marine environments.Corrosion advanced another significant step when, after World War II, designs of new and larger aircraft utilized larger and thicker metal sections in the manufacture of structural components. With thicker mill products came higher residual heat treat, fabrication and assembly stresses resulting in an increased number of stress corrosion and exfoliation corrosion problems.Apart from the exterior environment, aircraft interior s can be exposed to a number of fluids which are either directly or indirectly responsible for corrosion. The most common of the fluids is water which is usually introduced as a result of condensation, especially in pressurized fuselages, and spillage from lavatories, galley s and electrolytes from batteries. These fluid s have a degrading effect on protective treatments and are also corrosive to the substrate metal. Fluids such as phosphate ester hydraulic fluids and ester based turbine engine lubricating oil s are not corrosive to the substrate metal, albeit they do contribute to corrosion by the degrading effect on protective treatments."

Jan 1, 1988