Search Documents

Threshold blasting involves the use of small amounts of high explosive to break and fragment hard rock without having to evacuate mining personnel. The method is easily assimilated and effective in rockbreaking, but requires rigid control on drilling, charging and timing. Current underground trials are aimed at fine-tuning the amount of explosive energy and blast hole geometry to allow the firing of multiple sets of shot holes in a continuous manner. Through correct procedures, the after-blast fumes, dust and fly rock can be contained so as to provide a safe working environment. Threshold blasting hugely reduces the volumes of explosives used in mining and brings to maturity the potential of the process begun by Alfred Nobel when he introduced nitroglycerine, and later dynamite, to mining. Its key contribution is its enabling of continuous mining operations with well understood and relatively low cost technologies. The use of batch blasting, employing large burdens holds the greatest potential for delivering high flow rates of ore at minimal cost. There is good potential for rapid evolution of the concept.

Jan 1, 2002

By S Adamson

Morphological analysis of alluvial gold recovered from the same segment of a placer by four common commercial methods indicates that gold shape and the presence of quartz intergrowths or sulphide overgrowths substantially influence the recovery efficiency of each method. The amount and types of gold saved by each method varies according to the different hydrodynamic conditions under which each of the methods operates. Reverse circulation drilling has the lowest efficiency and preferentially loses moderate-high flatness gold and intergrown or overgrown gold particles with relatively low density. Gravity riffle, hydraulic riffle, and jigcentrifugal concentrator systems respectively save progressively more of these problematic gold morphotypes, but still lose significant and sometimes substantial amounts (of profit) to the tailings. Because of the differences in recovery efficiency, reverse circulation drilling probably underestimates the grade of most placers and may have resulted in bypassing several economic deposits. Losses to tailings by commercial recovery plants arise from inadequacies in fundamental plant design features. These inadequacies compromise plant efficiency by limiting the ability of plants to simulate the wide range of hydrodynamic conditions necessary to operate effectively throughout placer systems. Incorporation of sand pumps and multiple recovery methods into the more sophisticated plants only partly overcomes these inadequacies. At best, efficiency will be maximised in a few segments of the placer determined by individual plant design, and will decrease progressively upstream and downstream of those segments. Without prior knowledge of the morphological characteristics of the gold to be mined, it is difficult to choose the most appropriate plant design, or to estimate what proportion of the gold will be recoverable by any given plant. If the relevant relationships are not considered beforehand, the recovery plant is likely to lose a significant proportion of the gold, and sacrifice maximum profit.

Jan 1, 2001

By Carole L. B. Mitchell

The South 180th Street Grade Separation underpass in Tukwila and Renton, Washington, USA, permits vehicular traffic to pass beneath Burlington Northern Santa Fe and Union Pacific railroad tracks. The railroad tracks were temporarily relocated onto a shoofly crossing while the permanent bridges were constructed. The maximum underpass depth is approximately 25 feet (7.6 meters [m]). The majority of the sidewalls are supported using alternating reinforced and unreinforced secant pile walls. Temporary and permanent struts brace the top of the excavation. Because the groundwater is about 15 feet (4.6 m) above the base of the excavation and the subsurface materials are loose to medium dense fill, alluvium, and soft flood plain organics, the base of the excavation was strengthened and sealed using wet cement deep soil mixing (CDSM) methods. During construction, CDSM-treated ground temporarily acted as part of the railroad shoofly shoring while the remainder of the underpass was excavated on either side of active railroad tracks. The combination of secant pile sidewalls and CDSM bottom seal allowed for easy excavation, even during wet conditions. Using a 35-foot-thick (maximum) (10.7-m) CDSM layer both to act as a bottom seal and to resist uplift pressures is a unique, dual-purpose application of CDSM technology in the United States.

Jan 1, 2004

By J. West

For many years line-of-sight (LOS) issues for underground mobile equipment is a growing focus of research. This research is a result of the numerous fatalities and injuries which occur in the mining industry and which are related to poor operator LOS. Three assessment methods are currently used to assess operator LOS of underground mobile equipment. The light filament (LF) method is a hands-on assessment method that is performed in the field. This method is not evaluated in this paper. The laser scan (LS) method of assessing equipment is a quick and reliable method that comes from the need to evaluate vehicles already located in the field. The computer simulation (CS) method can assess LOS issues using a computer aided drawing (CAD) model, which is useful for assessing current or prototype models. The purpose of the current research is to compare and validate different operator LOS assessment methods. Comparison of the results of the LS and CS visibility plots yielded similar quantifiable results. A visual comparison of the results further illustrate that the LS and CS methods are acceptable assessment tools for mobile equipment operator LOS evaluation. The visibility assessment methods are now being prepared as guidelines for the mining industry to assess current and potential designs.

Jan 1, 2007

By J. West

For many years line-of-sight (LOS) issues for underground mobile equipment is a growing focus of research. This research is a result of the numerous fatalities and injuries which occur in the mining industry and which are related to poor operator LOS. Three assessment methods are currently used to assess operator LOS of underground mobile equipment. The light filament (LF) method is a hands-on assessment method that is performed in the field. This method is not evaluated in this paper. The laser scan (LS) method of assessing equipment is a quick and reliable method that comes from the need to evaluate vehicles already located in the field. The computer simulation (CS) method can assess LOS issues using a computer aided drawing (CAD) model, which is useful for assessing current or prototype models. The purpose of the current research is to compare and validate different operator LOS assessment methods. Comparison of the results of the LS and CS visibility plots yielded similar quantifiable results. A visual comparison of the results further illustrate that the LS and CS methods are acceptable assessment tools for mobile equipment operator LOS evaluation. The visibility assessment methods are now being prepared as guidelines for the mining industry to assess current and potential designs.

Jan 1, 2007

By Noel C. Joughin

In making judgements on tolerable levels of risk in industry, and in all spheres of life, it needs to be understood that every action gives rise to risk. Without risk, nothing can be done. Without risk, no economy could be advanced. There is a strong tendency to emphasize the risk at work, but persons who are not working are exposed to a different set of risks. Often persons who are not working face greater risks than persons who are working. Simply, in being alive, one is exposed to the risk of an accident, the risk of contracting a disease, and an extremely diverse variety of other risks. According to the Health and Safety Executive of the UK, it is not possible to have a state of zero risk, because ?a state of zero risk does not exist?. Because zero risk is a physical impossibility, it is not possible to design for a state of zero risk in all engineering design. While the strategic target of achieving zero risk is laudable it does not provide any practical guidance to engineers as to what acceptable limits of risk should be. This causes a significant and real problem in the design for and the management of risk. Without meaningful guidelines, engineers, managers and the authorities often find themselves in disagreement. Thus, it has become essential to establish criteria for tolerable levels of risk and unacceptable levels of risk in order to design and manage engineering systems properly.

Jan 1, 2011

This paper considers the application of recent laboratory gas sorption data to the understanding outburst phenomena in underground coal mining. Previous use of threshold limits based on gas content and coal rank are placed in perspective. Although this work focuses on overseas research and experience, parallels can be drawn for New Zealand coal settings, taking into account localised mining and geological factors.

Jan 1, 1994

By M. K. Pelser

The purpose of this paper is not so much to provide a scientific study of the selection process for the perusal of other psychometrists or industrial psychologists?the purpose is to provide line management with a practical, relatively user-friendly guide to fair and scientific selection. The main areas that are to be covered are: ? Why fair and scientific selection? ? Job analysis ? The job requirement?selection technique circle ? Assessment centres in the mining industry?the Tavistock Collieries Ltd experience. Why fair and scientific selection? Seen from a line manager?s perspective, fair and scientific selection should be pursued for two main reasons: ? to remain within the ambits of the law ? to maximize the probability of selecting the potentially most productive and efficient candidate for the job.

Jan 1, 1997

The main objectives of the Mine Mechanisation and Automation program (MMAP) are to enhance health and safety in underground mining operations, facilitate mechanization and automation in narrow-vein and deep mines, provide sound science to regulatory agencies and improve mine profitability. The program, which has a unique underground and surface industrial scale facility, is involved in many multi-partner projects, like hydrogen fuelcell applications, electrification and hydraulification of underground mines, reduction of noise and vibration, miner location device, explosive-free blasting and hoisting. The paper presents an overview of the Mine Mechanisation and Automation Program of Natural Resources Canada and some of the main projects.

Jan 1, 2002

By D. Hopkins, D. Türler, R. D. Giauque, W. B. Davis, M. Karaca

In a highly collaborative research and development project with mining and university partners, sensors and data-analysis tools are being developed for rock-mass characterization and real-time measurement of mineral content. Determining mineralogy prior to mucking in an open-pit mine is important for routing the material to the appropriate processing stream. A possible alternative to lab assay of dust and cuttings obtained from drill holes is continuous on-line sampling and real-time x-ray fluorescence (XRF) spectroscopy. Results presented demonstrate that statistical analyses combined with XRF data can be employed to identify minerals and, possibly, different rock types. The objective is to create a detailed three-dimensional mineralogical map in real time that would improve downstream process efficiency.

Jan 1, 2002

By A. Mainza

It is common practice in the mineral processing industry to use hydrocyclones for particle classification. However, classification in the UG2 platinum circuits using the hydrocyclone poses major challenges due to the differences in density between silica and chromite, the two major components of this ore. Silica, the PGM carrying component, has an average density of 2.7 and the barren chromite component has an average density of 4.5. When conventional and flat bottom cyclones are used there is a misplacement of particles due to differences in density leading to inefficiencies in the classification by size. As a result of the density effect, coarse silica reports to the overflow, resulting in loss of recovery, and fine chromite reports to the underflow, resulting in loss of milling capacity and unnecessary production of fine chromite. A classifier based on a different concept was required in the classification of UG2 platinum ore. The three-product cyclone, which is a hydrocyclone with two concentric vortex finders to produce three distinct products, has been tested in the UG2 ore application and indications are that misplacement of particles due to differences in the component densities can be minimized through the use of this unit. Industrial and pilot plant trials were conducted and indications are that the three-product cyclone can be installed to selectively produce a middlings stream that can be screened using Pansep screens to provide a screen oversize, which is predominantly coarse silica that can be preferentially reground to recover the PGM values contained in the coarse silica.

Jan 1, 2005

By E. C. Tarpley

An acid-extraction procedure developed in Germany for determining mineral matter in coal was investigated by the Bureau of Mines to determine its application to American coals. It was found to be suitable for all ranks of coal from anthracite to lignite if modified slightly for coals containing considerable quantities of calcium compounds, such as calcite or calcium humate. The precision of the method is satisfactory, and the results are probably closer to the true content of mineral matter than those obtained by empirical formulas. The method requires considerably more analytical data than the Parr or approximation formulas but is no more time consuming than obtaining the necessary data for the King, Maries, and Crossley formula (theoretically the most comprehensive empirical formula used). An appendix to this report includes a detailed description of a recommended procedure.

Jan 1, 1959

By M D. Hannington

On the southern flank ofLihir Island, a group of three volcanic cones were discovered at water depths from 1000 - 1500 m. The volcanoes are located in a narrow zone of recent seismic activity and elevated heat flow (up to 100 mW/m2). The recovered rocks consist of fresh alkali-olivine basalts, clinopyroxene-rich basalts, and porphyritic phlogopite basalts. One of the volcanoes has a recently erupted ejecta blanket (recovery of warm ash!), containing a suite of abundant mafic to ultramafic xenoliths. These xenoliths appear to represent a unique cross-section of subduction-modified mantle material sampled by volatile-rich primary fore-arc magma during its ascent to the seafloor. The most spectacular finding was the discovery of an active hydrothermal system with associated vent fauna and mineralization at Edison Seamount, and the recovery of unusually gold-rich (up to 43 ppm Au) hydrothermal precipitates in 1050 m water depth at the top of Conical Seamount, only 25 km south of the world-class epithermal Ladolam gold deposit on Lihir. The discovery of submarine hydrothermal vents associated with highly alkaline, quartz-undersaturated fore-arc volcanics represents a significant departure from similar hydrothermal systems on the mid-ocean ridges and in back-arc basins. The high gold grades in hydrothermal precipitates at Conical Seamount may indicate the first documented example of a shallow-marine epithermal system analogous to those known on land, and has important implications' for the gold potential of submarine arc environments.

Jan 1, 1995

By Robert Stefanko

The following tables contain the average, maximum and minimum power parameter levels for several mining machines. Power factor is listed only for defined transducer output regions. The reasons for the undefined areas are provided in the Instrumentation Chapter. Several maximum voltage drops are included, and are computed from the no load line-to-line voltage: Again, the drops are from measurements at the low side of the load center. The machines are: Continuous Miners; F6A Alpine 76AM Jeffrey (d-c) 8CM Joy 8CM (10CM) Joy 9CM-2AH Joy loam Joy CU-43-2H Joy 2 each CM26H Lee-Norse CM28E Lee-Norse Shuttle Cars; 18SC Joy 48S Torkar (a-c) 2 - 10SC Joys input to rectifier 2 - 16SC Joys input to rectifier

Jan 1, 1973

By G. L. Oldright

As a rule, the usual zinc retort smelter fired with natural gas made its own burners, of which there might be 300 per block, out of standard pipe fit-tings. The gas was discharged through a feeder pipe at various distances into a cylindrical horizontal "blow hole" through a pillar block and thence into the furnace; the best location of this gas-feeder pipe was at the horizontal central axis of the blow hole; the side entry into the blow hole usually was used. The air entered the same blow hole behind the gas, through a short nipple, in the inner end of which was a constructing orifice in a clay plug; in this ,work cone-shaped funnels of various lengths also were used. Even with the air and gas correctly proportioned to each burner, small differences in their dimensions were found to influence greatly the temperatures reached, their uniformity, and consequently the percentage of zinc extracted. This fourth paper of a series on cooperative work in the zinc retort plants of the Eagle-Picher Mining & Smelting Company discloses the methods and principles followed in approximating closely the optimum dimensions for various burners, with examples from experimental and commercial furnaces showing the interrelation of such dimensions with combustion and temperatures in the furnace.

Jan 1, 1948

By John W. Fredland

Many accidents occur in the mining industry as a result of the instability of material during handling and processing operations. Accidents due to dump point instability at stockpiles, and at spoil or waste piles, for example, occur with alarming frequency. Miners must be trained to be better aware of these hazards. Information on safe working procedures at stockpiles and surge piles is provided. Mine operators must review their training and operating procedures regularly to ensure that hazardous conditions are avoided.

Jan 1, 1993

By Dae S. Young

A new probabilistic approach is introduced for slope stability analysis including adverse impact of blasting vibrations. The material strength within a slope area is randomized in this bi-variate joint probability analysis. To be a completely general engineering method, the new probabilistic approach employs the random variable transformation technique; the Hermite model of the Gaussian transformation function, which transforms the experimental histogram of strength values to the standard Gaussian variables. Because bi-normal joint probability is analyzed on the true probability region projected on the Gaussian transformed variable plane, it is an exact solution of slope stability based on the available sample data. Details of the probabilistic approach are given through a case study on an iron ore mine. The case study demonstrated that the probabilistic approach is effective and simple enough to be a routine engineering practice for slope analysis.

Jan 1, 1984

By C. E. Sims

THE following presentation is more a summation of observations made and conclusions drawn over a period of three to four years than a report of experiments made with a definite objective. Tests were made, of course, to verify hypotheses, but the large mass of data was collected incidental to other work. Lack of space forbids the presentation of more than a few of those data. On the other hand, it is unfortunate that some of the most illustrative examples are not available. The work is admit¬tedly incomplete but is presented in the hope that it will stimulate further work along a similar line. The answers to many of the questions left unanswered by this paper will be found only after long and painstaking study, such as is scarcely possible in a commercial laboratory where problems of immediate importance consume most of the time. It is also hoped that this study will in some measure throw light on some of the dark spots of steelmaking, and help to clarify some of the annoyingly vague references to "good practice." Only cast steel was studied and the conclusions apply to cast steel, but it is the authors' opinion that the quality of rolled or forged steel is largely dependent on the quality of the ingot, which is a casting. Although this discussion deals almost entirely with inclusions, it is important that the reader understand that only those natural inclusions which owe their origin to the solubility of certain materials in steel and to the chemical reactions of steelmaking are considered. Accidental inclusions, such as entrapped particles of slag, nozzle, runner, or mold are outside its province and are not considered. Such accidental inclusions are always dangerous and should be carefully avoided.

Jan 1, 1932

By K. Goshtasbi

In this paper a genetic algorithm is used in a heavily jointed rock mass in order to investigate the critical circular slip surface and modification of slope surface. This method was applied to the southern wall of the 6th Golbini Jajarm bauxite mine. The mine is the largest bauxite deposit in Iran, located to the northeast of the town of Jajarm in the Khorasan province. Estimated reserve of bauxite in this deposit is about 160 million tonnes. Field and laboratory investigations were conducted in order to determine rock mass behaviour. A genetic algorithm code that uses the Simplified Bishop method as an objective function was developed for findingt he safety factor of circular slip surfaces. Sensitivity analysis was applied to determine the optimum values of the genetic algorithm variables, such as population size, selection method, crossover and mutation rates. After finding the critical circular slip surface, slope modification is carried out by removing unstable sections from marked critical slip surfaces, and this process is repeated until the last unsafe section is removed. Based on this code, modification occurred during 7 steps, by reaching a safety factor of 1.3 in the last step. Finally, the modified slope angle of the southern wall of the 6th Golbini Jajarm bauxite mine was determined to be 48.44 degrees. Keywords: Genetic algorithm, slope modification, circular slips surface, 6th Golbini Jajarm bauxite mine .

Jan 1, 2008

CONTENTS: Broken Hill The mixing stations.Operating and mixing apparatus.Pulp distribution.Stope preparation.Filling procedure.Consolidation of old fill.Drainage:Pulp density tests. Life of sand pipe lines.Results.Advantages and disadvantages.Conclusion and acknowledgments.General remarks on South Limited.Mining methods.History of stope filling in Broken Hill.Need for a new and better filling method and transport system.Initial experiments with hydraulic stowing.Source of the sand.Water Supply.Signalling system.GENERAL REMARKS ON BROKEN HILL SOUTH LIMITEDThe South Mine, property of Broken Hill South Limited, is situated at Broken Hill, N.S.W., Australia, towards the southern end of the main lode.The leases (M.L's 7 and 8)' cover a length of 2,400 feet along the lode outcrop and the workings extend, at this date, to a depth of 1,940 feet below the collar of the original main shaft and to 825 feet below sea level.Mining operations have been continuous for about 58 years and during this period nearly 12.5 million tons of ore have been mined. The monthly tonnage extracted approximates 30,000 tons in normal times.The ore is a mixed sulphide containing galena and marmatite; the gangue minerals are principally calcite, rhodonite, quartz and garnet.A typical assay for a monthly period is 14·40/0 Pb., 5·6 ozs. Ag., and 11· 60/0 Zn. The whole of the ore is concentrated on the property by combined gravity and flotation methods. The lead and 'zinc concentrates produced are railed to other centres for the extraction of the contained metals.MINING METHODSMining practice throughout the field varies only in minor details. The ore-bodies forming the Broken Hill Lode lie within complex folds arranged along a shear and vary in size and mineralogical associations, but all the mines have similar types. Some of the ore-bodies have weak walls, but the chief difficulty in mining is caused by "heads" and "flaws" in the ore.Besides these local weak areas there are ground movements-referred to later-of varying magnitude extending throughout the central portion of the lode where the large ore-bodies, several hundred feet wide, approached the surface.

Jan 1, 1944