Search Documents

By Donald W. Mitchell, John Nagy, Edwin M. Murphy

To increase safety and productivity in mining , the potential uses and hazards of rigid foam were investigated by the Bureau of Mines Experimental Coal Mine . This research resulted in the development of chemical formulations , spraying equipment , and application procedures that permit safe and effective use of urethane foams for improving mine ventilation , for reducing weathering of mine rock and steel , for constructing seals in fire areas , and for thermal insulation .

Jan 1, 1964

By S Agdaca

Leightons is the sole contractor at the Wahana Coal Mine Project (part of the Bayan Group), a multi-seam thermal deposit consisting of 13 coal seams with thicknesses ranging from 20 cm to 500 cm. The average dip of the deposit is 18 - 20°. However the deposit is heavily faulted in certain domains with anticlinal and synclinal structures present causing seams to dip up to 90°. Average thickness of coal inter-burdens range from less than 2 to 12 m. The minimum coal thickness being mined is 20 cm. Coal production is direct mine mouth feed and there is no coal processing plant currently used.Conventional blasting between the highly variable coal horizons in the early phases of the mine life was suboptimal from a production perspective. Drilling short holes with a reduced drill pattern, and on occasions with sloping benches, resulted in low drilling and explosives loading efficiency.A high frequency of small size blasts fired up to two times daily was required with each blast consisting of four up to five small blast areas. Each blast averaged approximately 36 000 bcm thus causing a low utilisation rate of the mining fleet from frequent blast delays and the inability to deploy larger Liebherr 9350 excavators on bench. It was identified that increasing the production targets required a more efficient drilling and blasting process. Furthermore, due to the highly variable nature of the deposit, the existing coal model was determined to not be able to accurately predict the coal seam location prior to blasthole drilling.In August 2009, Leighton Contractors Indonesia and Orica Mining Services with the full support of the Wahana team, initiated through seam blasting trials using electronic blasting systems. Further trials were conducted in November 2009. Trial evaluations indicated that the benefits from decreased lost time events due to blasting, an increased vertical advance rate per blast, and increased overall blast size could be attained while not damaging or diluting coal.Full-scale?through seam blasting has been ongoing since February 2010 for the upper eight coal seams to extract coal seam thicknesses ranging from 20 - 100 cm. This paper will discuss the parameters of the through seam blasting process in Wahana and the resulting benefits to the overall mine production.

Nov 8, 2011

By A. Lebedev

Application of dynamic simulation for a base metal processing plant is discussed. The plant receives ore of variable quality from two pits and blending had to be applied to maximise recovery. The plant employs multiple stage crushing, screening, dense media separation, two-stage milling, flotation and further filtration. Stockpiles and bunkers are used in the plant to cater for breakdowns and operating delays, the latter being appropriately incorporated in the model. A detail dynamic simulation model was constructed from the rock face to the filtration plant to assist the plant design, notably with definition of the ore blending method, sizing storage capacity and in-plant conveyors. The plant model was broken down to capital equipment items and various feed types and mass balances were tested to ensure that the production target is met. The dynamic simulation tested the proposed blending method, identified bottlenecks, produced risk profiles for all strategic storage facilities and overall helped minimise the project risks and improve confidence in the plant design. Keywords: Dynamic simulation, ore grade, blending, capacity, risk profile, throughput, utilisation

Jan 1, 2020

By Tiago Evangelista Gomes

O presente trabalho teve por objetivo verificar a influência do Nióbio na trabalhabilidade a quente de um aço inoxidável duplex do tipo UNS S32304 em condições similares às do processamento industrial, utilizando ensaios de torção a quente. Foram fundidas, em forno de indução a vácuo, 4 corridas experimentais: uma com a composição química padrão e as outras objetivando-se teores de Nióbio de 0,2%, 0,4% e 0,8%. Ensaios de torção a quente foram realizados em resfriamento contínuo a partir de 1.200ºC, e ensaios isotérmicos no intervalo de temperaturas de 1.200 a 900ºC. O aumento da fração volumétrica de ferrita em função do aumento da concentração de Nióbio melhorou a trabalhabilidade a quente destas ligas.

Jul 30, 2018

By Stanislas Mauuary

Price pressure is a real challenge on the stainless steel market. With market globalization, increase production capacity and exorbitant raw material, the margins are squeezing for stainless strip producers. Primetals Technologies offers a wide range of advanced technological solutions to secure the margins of our customers. Our solutions, implemented with professional project management, allow an optimum coil to market time, securing then the return on investment for the investor. Among the possible lever used to optimize the production route, one drastic step can be made to cut rolling time and cost by replacing the common 20-Hi mill stand reversing process by state of art high capacity X-HI® stands in continuous rolling line. Other source of savings can be implemented by integrated several process steps together (rolling, annealing, pickling, skin passing), achieving then savings on stocks and logistics while coil processing is reduced to fraction of hour. Additional solutions can also be implemented on the new, as well as existing line, like maintenance free solid state laser welder, skin-pass and tension levelers, in-line inspection system coupled with process and quality management system.

Aug 17, 2017

By Jonatas Venâncio Barbosa

Descrevem-se as ações adotadas para a evolução da qualidade de aços ultra baixo carbono com alto teor de silício, destinados a aplicações eletrônicas. Com o propósito de conhecer o comportamento metalúrgico do material durante o processo de laminação foram realizados ensaios de dilatometria, que permitiram a determinação das temperaturas de transformação de fase. Foi evidenciado que, nas temperaturas de processo praticadas, a laminação no trem acabador ocorria na região intercrítica, gerando variações bruscas de propriedades mecânicas no processo, levando a instabilidade operacional. Esta condição de laminação foi corrigida, direcionando para laminação em fase ferrítica. Foram necessários ajustes no modo de operação na linha de tiras a quente e a criação de controle automático de temperatura na entrada do trem acabador. Após as ações foi possível melhorar a qualidade do produto final, em relação às dimensões e forma do produto, reduzindo as perdas internas e retrabalho.

Aug 16, 2017

By Laurent Dorel

Surface quality monitoring is primarily implemented in the last steps of steel manufacturing before shipment to the end user. However, an increasing trend for also addressing this topic in the upstream stages, such as hot rolling plant, is tackled by Primetals Technologies to give steel producers the key to a global optimized yield management, and efficient “lessons learned” processes. After the last developments of SIAS Next Gen platform, including High Resolution and Near Infra-Red, some site results will be exposed on the very specific high constraints lines such as ESP Endless Strip Production and Plate Mills, and highlights the related most interesting aspects for our customers.

Aug 17, 2017

By Mine F. J, Woods P. H

The Top End of the Northern Territory lies in the monsoonal zone and receives rain during the November-April period. Initially, at the start of the wet season, rain storms are localised, but, following the descent of the monsoonal trough from below the equator, widespread rain occurs. Overflow incidents at mine sites tend to arise midway through the annual wet season when excess water accumulated in ponds begins to discharge to the external environment. Remote-access monitoring may be undertaken at mine sites using equipment to continuously measure water quality parameters with storage of the information on a data logger. The data is then retrieved by visiting the site and transferring it to a portable computer or by remotely accessing the system using a telemetry system and transmission via telephone, VHF/UHF or satellite. Such systems are readily available and vary in cost depending on the sophistication of the data transfer system. Available sensors for continuous monitoring include those for conductivity, temperature, pH and other ion selective electrodes, eg nitrate, and water level. Of these variables, conductivity is most useful due to its inherent accuracy and stability of reading. Remote monitoring capability is able to provide: (i) more intensive monitoring of key issues; (ii) more timely information; (iii) correct perspective on the degree of environmental problem; and (iv) information from remote locations, which would be difficult to monitor by more conventional methods. Examples are given for applications of continuously logged measurement of conductivity of waters discharging to drains and in creeks at Pine Creek, Ranger, Nabarlek and Woodcutters mines in the Northern Territory. These applications demonstrate the timeliness of the continuous monitoring technique.

Jan 1, 1994

By F. W. Hoertel

The Bureau of Mines investigated the use of depleted uranium as a sacrificial anode for the cathodic protection of submerged and underground structures of iron , steel , and copper . Uranium-metal couples were tested in simulated marine environments of varying oxygen contents at pH values between 5.5 and 8.5 and under simulated boiler service condition in Rolla , Mo. , city water . Similar couples were tested in samples of Missouri soils to simulate underground service . Uranium remained anodic to iron , steel , and copper in the simulated marine environments and under simulated boiler service if the electrolyte was oxygen- free city water . Uranium appeared to offer limited protection to iron , low- carbon steel , stainless steel , copper , and zinc in the simulated underground tests . Uranium anodes offer a space advantage because 1 cubic inch of uranium gives approximately the same protection as 2 cubic inches of magnesium or 1-1 /2 cubic inches of zinc .

Jan 1, 1963

By Ferry Belisario Benique

A empresa Aceros Arequipa S.A. no seu complexo siderúrgico situado na cidade de Pisco, no Perú, está reutilizando os finos das pelotas de minério de ferro na fabricação de aglomerados (briquetes) para uso no processo de redução direta em forno rotativo na fabricação de ferro esponja (DRI). Dessa forma, testes no laboratório foram realizados com o objetivo de encontrar um ligante ou mistura de ligantes que proporcione um aglomerado com boa resistência à compressão a frio e boas propriedades mecânicas a quente que garantam sua integridade dentro do forno durante o processo de redução. No presente trabalho apresenta-se a metodologia desenvolvida e os resultados obtidos na fabricação dos briquetes em laboratório e na planta piloto de briquetagem de finos. Adicionalmente, resultados dos briquetes após redução no forno rotativo a escala industrial também são apresentados.

Aug 1, 2018

By A. C. Johnstone

The aim of the study is to determine if pit lakes are a sustainable coal mine closure option in South African. The water balance, chemistry, limnology, and bacterial population of three selected pit lakes were investigated. The lakes are in the three major coal basins of South Africa and are associated with different lithologies and mining methods. The major factors driving the water balance of the pit lakes are direct rainfall, runoff, inflow from old mine workings, and groundwater infiltration, with the major losses being evaporation or discharge onto surface. The study indicated that pit lakes can be designed as ’terminal sinks’ to provide a sustainable mine closure option. The pit lakes sampled have an alkaline pH, and mostly a sodium/calcium sulphate water with total dissolved solids content of less than 3000 mg/l. The phytoplankton and microbiological data indicates that the pit lakes support aquatic life. The study shows that correctly designed pit lakes can be an environmentally sustainable closure option for South Africa’s coal mines. A suggested design manual has been developed to assist mine owners and regulators in developing sustainable coal mine pit lakes as a closure option.

Oct 1, 2021

By Anton Sizo, Alexey Klyashtorin

The Gunnar uranium mine operated from 1953 to 1961 on the shore of Lake Athabasca, in 1964 the site was abandoned, and the mine pit flooded. In 1981, the pit was found to be stratified with a chemocline at ~70 m by a sharp change in conductivity and TDS. The uranium concentration was ~700 μg/l on the surface, 320 μg/l at 50 m, and 2,900 μg/l at 110 m. The Ra-226 concentrations were 0.1, 0.06, 0.12, and 0.4 Bq/l. By 2017, the chemocline was ~60 m deep. The highest uranium concentration was 1150 μg/l and the lowest concentration (220 μg/l) was attributed to the chemocline. In the deeper column, the uranium content varied around 750 μg/l. The uranium distribution down the pit profile was aligned with DO, ORP, and TDS. Ra-226 averaged to ~0.4 Bq/l, Ra-226 and uranium profiles were inversely related with the respective maximum and minimum attributed to the chemocline. The uranium and radium amount accumulated in the pit by 2017 was 3,420 kg and 2,163 GBq, respectively. The uranium and radium apparent accumulation trend estimates to 64 kg/y and 41 MBq/y, respectively. A stable chemocline and no concentration gradients in the other parts of the pit suggest that the contaminants are unlikely to inflow from the bottom opening or outside the pit, but rather are mobilized from the pit walls. The contaminants are not in a steady state, and concentrations of both uranium and radium are likely to increase slowly in the future if no remediation occurs.

Jan 1, 2020

By J Wall

The use of electronic detonators in civil tunnelling applications, to reduce vibration in small firings has been successfully utilised for a number of years. As part of the mining industry’s commitment to reducing blast damage during the development cycle in underground mining applications, a series of development blasts using e-Dev™ electronic detonators in a typical mining application was conducted at Resolute’s Mt Wright operations in North Queensland in 2010. Results were based on direct comparisons to the current industry standard of non-electric firings as a baseline, with as many parameters as possible being captured during the trial. Development costs are typically high in most underground mines, especially in capital development headings, which are in waste and therefore of no direct economic value, so by being able to accurately fire to design, costs relating to both ground support requirements and volume of material removed, (and therefore haulage required) can be minimised. A direct comparison of overbreak (ground blasted outside of design) and cast (distance rock thrown from blast) was also made during the trial, as well as close monitoring of the drilling accuracy.

Mar 21, 2011

By Mine F. J, Woods P. H

Waste waters from mine sites may be screened for all constituents of significance as a first step in establishing water quality criteria for protection of aquatic ecosystems. Inductively-coupled plasma mass spectrometry (ICP-MS) offers the capability to screen water samples and digest solutions for virtually all elements in the periodic table. This technique is therefore able to identify elements whose concentrations are elevated in waste waters and may be rarely present in background surface or ground waters. Such elements may be present in waters at only a few ¦g/L. ICP-MS has sufficient sensitivity to detect sub-¦g/L or even ng/L levels of many elements. Waste waters from most mining activities in the Northern Territory have been examined by ICP-MS. The concentration data provide the basis of a contaminant data base. The data can show specific tracers in the ore or mineral itself, subsequently found in waste water. An example is the presence of rhenium in uranium ore. Such trace elements may be present in soluble or insoluble chemical forms and are more useful as indicators when soluble and exemplifying conservative chemical behaviour. The approach described, based on ICP-MS screening of mine site waste waters, together with general physico-chemical variables, provides the most comprehensive means yet available of selecting variables for monitoring programs and ensures that key elements and/or their chemical species are not excluded from monitoring programs.

Jan 1, 1994

By Rafael Oliveira Sena

A SMS Siemag tem oferecido ao mercado brasileiro novas tecnologias para Lingotamento Contínuo de Placas com objetivo de aumento de desempenho dos equipamentos. A SMS Siemag tem desenvolvido e otimizado o processo de revestimento de placas de cobre do molde que utiliza em conjunto com o processo de eletrodeposição a tecnologia thermal spray que proporciona um produto com alta propriedade de resistência ao desgaste. O revestimento cerâmico, mais conhecido como UniGuardTM, tem obtido resultados excelentes no mercado da América do Norte atingindo valores superiores a 300.000 toneladas. A utilização do revestimento UniGuardTM proporciona um aumento de produtividade e redução dos custos de manutenção do molde bem como redução de aquisição de novas placas de cobre.

Jul 29, 2018

By J. R. Patts, A. B. Cecala, E. J. Haas

Exposure to respirable crystalline silica (RCS) remains a serious health hazard to the US mining workforce who are potentially exposed as various ore bodies are drilled, blasted, hauled by truck, crushed, screened, and transported to their destinations. The current Mine Safety and Health Administration (MSHA) permissible exposure limit (PEL) for RCS remains at approximately 100 μg/m3 , but it is noteworthy that the Occupational Safety and Health Administration (OSHA) has lowered its PEL to 50 μg/ m3 (with enforcement dates staggered through 2022 for various sectors), and the National Institute for Occupational Safety and Health (NIOSH) has held a 50 μg/m3 recommended standard since 1976. To examine a method for reducing RCS exposure using a NIOSH-developed video exposure monitoring (VEM) technology (referred to as Helmet-CAM), video and respirable dust concentration data were collected on eighty miners across seven unique mining sites. The data was then collated and partitioned using a thresholding scheme to determine exposures that were in excess of ten times the mean exposure for that worker. Focusing on these short duration, high magnitude exposures can provide insight to implement controls and interventions that can dramatically lower the employee’s overall average exposure. In 19 of the 80 cases analyzed, it was found that exposure could be significantly lowered by 20% or more by reducing exposures that occur during just 10 min of work per 8-hour shift. This approach provides a method to quickly analyze and determine which activities are creating the greatest health concerns. In most cases, once identified, focused control technologies or behavioral modifications can be applied to those tasks.

By J-P Strydom, J P. Z, S. Schafrik, M. Beck, Z. Agioutantis

Developing a method to accurately determine the weight and distribution of the load within a shuttle car bed eliminates the need for manual activation of the flight chain. Accordingly, this experimental study characterized the thermo-mechanical response of two unique load cells in force shunt, implemented as an engineering control to quantify load position and distribution without human intervention. The influence of environmental and installation conditions on the measurement accuracy was quantified and determined to be indirectly dependent on the characteristics of the material load cells that are mounted to.

Feb 22, 2026

By William Gleason

At 6,898 ft below surface, the historic No. 9 shaft at Resolution Copper near Superior, AZ is now the second deepest single lift mine shaft in the United States and connects to the deepest single lift mine shaft in the U.S., Resolution Copper’s No. 10 Shaft (6,989 feet). The shafts serve as ventilation and access for future underground development of what could one day become one of the most significant copper mines in the United States. It is from the base of No. 9 and No. 10 shafts that hundreds of employees of Resolution Copper, a joint venture of Rio Tinto and BHP, hope will soon be given the go ahead to begin driving lateral tunnels to reach a copper deposit that is estimated to contain 28 Mt or 40 billion pounds of copper. Copper was recently added to the U.S. Geological Survey’s (UGGS) critical minerals list, in large part because of increasing demand. A study by S&P Global Energy & Market Intelligence “Copper in the age of AI: Challenges of electrification” released on Jan. 8, 2025, “identifies a transformative trajectory for copper demand, projecting a surge from 28 Mt (31 million st) in 2025 to 42 Mt (46.3 million st) by 2040 – a 50 percent increase that underscores the metal's pivotal role in multiple technological and economic domains.” The surge in demand is driven in large part by the global energy transition, electrification of vehicles, growth of artificial intelligence and data centers, and most recently robotics. Meanwhile, geopolitical tensions have increased the focus on the need for the United States to secure more of its own mineral supply chain. S&P Global’s report is one of many warnings that while copper demand has accelerated rapidly, future supply is being held back. Resolution Copper stands out as one example of a known mineral deposit remaining locked in the United States’ complex and lengthy permitting slog.

Feb 1, 2026

By Xiaolong Lin, Jianhui Peng, Zhongping Zhu, Guanghui Li, Zhizhong Li, Zhiwei Peng, Tao Jiang

As the absorbing material composed of sole carbon is difficult to meet the comprehensive requirements of microwave applications, preparation of carbonaceous nanocomposite materials becomes an effective method to increase microwave absorption properties. In this study, a novel nanocomposite composed of Co–Ni ferrite and graphene was synthesized via a simple and rapid microwave hydrotherma method in just a few minutes It was demonstrated that the minimum microwave reflection loss of the composite of 3 mm thickness with a low filling ratio (20 wt%) reached −13.1 dB at 17.2 GHz with an effective absorption bandwidth of 3.1 GHz. The good performance of the composite was believed to be a result of high dielectric loss of graphene associated with a multi-dielectric relaxation process and magnetic loss of the ferrite mainly originated from natural ferromagnetic resonance.

Mar 1, 2018

By C. W. Davie

"This paper is the second of a series of progress reports4 on a study of the hydrometallurgy of manganese which is being conducted in an endeavor to make possible utilization of the large deposits of low-grade domestic manganese ores that occur in several States.There are at least four processes in which a knowledge of the action of SO2 gas on manganese oxides at elevated temperatures may prove of value.One of these involves dissolution of manganese from ores. The Bureau of Mines has investigated the hydrometallurgy of manganese by a process in which SO2 gas, a waste product at many smelters, is passed into water to form a solvent for manganese. Although several manganese minerals were readily dissolved, rhodochrosite (MnCO3) was attacked but superficially.5 Recent experiments have shown that a roast at 650 to 9000 C. converts the manganese of rhodochrosite to a form that is quickly dissolved by a weak SO2 solution.6 Introduction of smelter gases containing much as 5 per cent SO2 during such a roast would not add much to the cost of the operation, and might result in the formation of considerable water-soluble manganese sulpate.Another case involves a subsequent step in the hydrometallurgical process, namely, the formation of oxides of manganese with simultaneous evolution of SO2 by the heating of the MnSO4 produced by evaporating its solution.A third has to do with the roasting of zinc sulphide ores containing manganese as a preliminary to leaching. During purification of the solutions to be used for the electrolytic deposition of zinc the iron must be oxidized to make possible its removal. Manganese dioxide has been used for this purpose,7 and since manganese compounds are present in some zinc concentrates,8 it is of interest to learn what happens to the manganese in a zinc sulphide or on roasting, and what portion of the manganese in the roasted product might be available for oxidation."

Oct 1, 1930