Search Documents

The Olympic Dam copper/uranium deposit was discovered in 1975 and subsequently commenced production in 1988 at a rate of 1.5 Mtpa using the sublevel open stoping mining method. In the following five years the operation underwent two optimisation programs that have increased mine output to the current rate of 3.4 Mtpa of ore. The pre-expansion requirements were annual development of approximately 10 000 m and the placement of around 500 000 m 3 /yr of cemented backfill. Previous to 1995 all hoisting was carried out by the Whenan shaft. The Robinson shaft was commissioned during that year to hoist increasing development mullock tonnages and to allow for increased ore hoist via the Whenan system. In 1996 WMC committed to expanding the output of the operation from 85 000 tpa (1996/97 budget) copper metal to 200 000tpa. The corresponding increase in mine ore production requires expansion to a nominal rate of 9.0 Mtpa. To achieve these increased tonnages, major hardware installations will include sinking of a third shaft capable of hoisting in excess of 9.5 Mtpa, a rail haulage horizon utilising automatic trains, expansion of the existing backfill plant to a production capacity of over 1.8 million m 3 /yr, increasing long term development rates to 15 000 m/yr and increasing the production drilling and blasting rates in line with the higher stope production output. This paper provides detail into the intended hardware (shafts, equipment, etc) of the mining system, and outlines the intended long-term operation and management of the operation. Of particular note is the background requirement of ensuring existing production targets are met to provide critical cashflows into the project during the period of expansion.

Jan 1, 1998

By Markus A. Reuter, Bernardete Castro, Antoinette van Schaik, Han Remmerswaal

This paper describes the inseparable relation between product design, liberation, and metallurgical recovery in the optimisation of the recycling of passenger vehicles. This is illustrated by the use of an optimisation model that uses among others a material combination matrix based on metallurgical process data, which depicts the consequences of the quality of intermediate recycling products on the metallurgical material recovery and final alloy metal quality. Various simulations will illustrate the effect of changes in product design and hence liberation on the recycling of end-of-life vehicles. Although this paper focuses on cars, the discussion is equally valid for any end-of-life product. Calibration of the model will be discussed with reference to experiments carried out in order to study the optimal recovery of aluminium applications used in passenger vehicles.

Jan 1, 2003

By Michel Dagbert

In the exploitation of porphyry-type deposits, the quality of the ore is mostly defined according to its grade. Besides the simplest distinction, ore-waste, several grade categories may exist and they correspond to the different ways in which the ore is further processed. At the time of mining the selection of the different categories is done from extensive information available from blast holes. But planning has to be done before this information is available and it is necessary for the geologist to forecast, from exploration and development data alone, the possible outcome of the selection done later on a block, a level, or the whole deposit and ultimately predict the ore reserves and value of the deposit. A good statement of this problem has been presented at the 1976 AIME annual meeting by Williamson and Hueller (1976). They have shown that, if the cut-off values are directly applied to the estimated grade of blocks, a gross overestimation of the recovered tonnage of ore (14%) will occur. This problem, now termed "the vanishing tons problem" (DaVid, 1977) seems to be common in many open-pit operations and it has been explained several times (DaVid, 1972; Huijbregts, 1975). In order to solve it l.Jilliamson and Mueller proposed a solution based on compiling masses and masses of blast hole data available from mined-out portions of the deposit. They derived empirical correction factors which provide for every block, given its estimated grade, the expected tonnage and average -grade of each category of material within that block. The purpose of our work is to repeat the same exercise but ignoring the blast holes data i.e. we want to derive the correction factors from the only DOH data. Doing this, we are more in the real conditions where the valuation of the mine and are reserve analysis has to be made before production actually starts. Two possible ways to achieve this goal will be investigated and the emphasis will be on recently

Jan 1, 1977

By N. Moony

The benefit of gravity separation in improving total gold recovery in grinding circuits has been outlined in a significant number of papers to date. However, the use of batch centrifugal concentrators (BCC) as an industry standard to extract gold has limited the potential for maximizing gravity recoveries -particularly in coarse gold deposits. This is a reflection of the high upgrade ratios obtained by BCC's which has an inverse relationship with recoveries. Survey work in Australia has indicated that installation of the InLine Pressure Jig as an alternative to the Bee will significantly increase recoveries of gold by gravity and, accordingly, increase total gold recoveries and lower operating costs.

Jan 1, 1998

By J Lea, D C. Kettlewell

The Carina iron ore deposit lies 105 km northeast of Southern Cross, WA. The area designated the Yilgarn Iron Ore Project (YIOP) is comprised of five prospects along an east-southeast trending greenstone belt that extends from the Helena-Aurora Ranges in the northwest to the Yendilberrin Hills in the southeast, over a strike length of approximately 40 km. The YIOP project encompasses the previously identified iron deposits of Bungalbin, Bungalbin East and Mt Walton. The Carina deposit was discovered by Polaris Metals NL in May 2007. The Carina deposit is located within and parallel to the structurally complex northwest trending Mount Dimer shear zone. The volcanosedimentary Archaean-aged greenstone sequence consists of ultramafic and mafic lavas and flows with interbedded sediments dominated by chert and banded iron formation (BIF). Supergene enrichment processes formed a goethite orebody replacement of BIF sequences within a doubly plunging synclinal fold structure. Mineralised outcrops dominated by goethite form a low ridge 1500 m long, up to 90 m wide and drilled to over 200 m in depth. In the vicinity of the Carina deposit, iron occurrences have been identified over at least a 12 km strike length and the exploration potential of the area is identified as 30 - 40 Mt. Polaris Metals began exploration in the area in 2006. Target generation in the area used existing state geological survey maps and regional magnetic survey data to focus on BIF occurrences associated with major structures. Early field investigations resulted in the identification of a large outcrop of predominantly goethite mineralisation at Carina. Detailed geological and structural mapping was completed, followed by close-spaced reverse circulation and diamond drilling. The mineralisation is predominantly goethite with specular and coarse platy haematite localised along structures that cut the goethite mineralisation. Mineralised zones are moderately vuggy and larger cavities occur in proximity to fault zones that transect the orebody. A capping by a thin veneer up to 9 m thick of canga or ferricrete occurs in places. By December 2008, 178 reverse circulation and 11 diamond drill holes (seven surface holes, four tails) were completed. The current JORC-compliant resource estimate is based on assays from 72 RC drill holes and using a 55 per cent Fe cut-off stands as an Inferred Resource of 27.9 Mt at 58.6 per cent Fe, 1.3 per cent Al2O3, 3.7 per cent SiO2, 0.09 per cent P, and 10.1 per cent LOI. Assaying has recently been completed and will be incorporated into a new updated resource later in 2009.

Jan 1, 2009

By David Ramírez

"Dentro del proceso de optimizar la fragmentación del mineral por voladura, el principal objetivo es determinar el impacto que tendría la incrementación de las partículas medias y finas sobre la extracción de cobre en elmineral ROM, (Run of Mine), que actualmente constituye una de las fuentes de producción por lixiviación en la Sociedad Minera Cerro Verde. En ese sentido, el presente trabajo describe la cantidad de cobre que aporta el mineral ROM a través de su optimización en el proceso, así como el impacto económico que tendría a futuro. Para ello, se utilizan los resultados de las pruebas para los módulos experimentales 12 y 13 desarrolladas entre 1998 y 2000, y la validación preliminar del sistema de análisis granulométrico por fotos (Split Desktop) desarrollado en julio del 2002 para así otorgar validez a los resultados fotográficos de granulometría reportados para las diferentes pruebas de voladura. "

Jul 31, 2003

By Vincent A. Scovazzo

"The most significant study on the effects of longwall mining on gas and oil well integrity was completed by a consortium of coal and shale gas industry participants. A field study was conducted in 2013 and 2014 and is referred to by its location on Well Pad NV-35. The experiment site was located at the CONSOL Enlow Fork Mine in Washington County, Pennsylvania.The experiment was completed to verify John T. Boyd Company (BOYD) calculations and studies completed under contract by for the Pennsylvania Department of Environmental Protection Gas Well Pillar Study Update. The findings of the original study were presented by BOYD at the 32nd Conference, while numerical analysis of the Well Pad NV-35 field study was presented by Dr. Su at the 35th Conference.This paper addresses the findings of the experiment and how it confirmed the conclusions of the original study.INTRODUCTIONA field study was conducted in 2013 and 2014 by a consortium of coal and shale gas industry members to test the effects of longwall-induced ground movement on the stability and integrity of wells drilled through a gateroad abutment pillar. The project was initiated to test initial John T. Boyd Company (BOYD) findings of the Gas Well Pillar Study Update (Scovazzo and Moran, 2014), completed for Pennsylvania Department of Environmental Protection, Bureau of Oil and Gas Management (PDEP). Background and initial findings on this project were presented at the 32nd Conference (Scovazzo and Moran, 2012). The field work and numerical analysis were spearheaded by CONSOL Energy, Inc. (CONSOL) with participation by Chevron, EQT, Noble Energy, Range Resources, Marcellus Shale Coalition, and the Pennsylvania Coal Alliance.Dr. Wen H. Su of CONSOL was the leader of the field experiment with input from the participants. Dr. Su also completed numerical analysis of the results and model casing deformation. Analytical results were presented by Dr. Su at the 35th Conference (Su, 2017)."

Jan 1, 2018

By Harold N. Miller

Lost time and services caused by electrical equipment breakdown or cable faults can often be substantially reduced by the use of direct-current high-voltage testing as a maintenance tool. This paper discusses the relative merits of alternating-current versus direct-current testing, pointing out the advantages in size and cost of equipment and more definitive results achieved through the use of D.C. General principles of direct-current high-volt-age testing, types of testing, methods of performing the actual test and interpreting the results are explained. ?The value of insulation resistance measurements and their relationship to high-voltage testing is discussed. Pinpointing the physical location of a cable defect using a fault locator or thumper is described. Reference is made to several organizations that have effected considerable savings with high-voltage test programs. Introduction T HE past decades have seen great advances in the field of electrical power distribution and application. Motor generators, power-operated equipment, cables, etc., have all gone through various stages of improvement both in efficiency and reliability. Un-fortunately, however, power failures and equipment breakdown still occur -frequently with disastrous effects in loss of time,

Jan 1, 1965

By Frank C. Andreuzzi

The Division of Environmental Activities, U.S. Bureau of Mines, conducted a solid waste demonstration project on a burning coal refuse bank. The primary objective of this project was to develop and evaluate an efficient method of extinguishing burning coal refuse and moving it. A series of tests were performed using water monitors and related apparatus to quench the burning material and, at the same time, using earth-moving equipment to transport, spread, and compact the extinguished material. The method found to be most effective consisted of water-quenching the surface material to a workable depth, ripping, and removing the quenched material with a bulldozer and tractor-scraper. The total cost was estimated to be $0.44 per cubic yard.

Jan 1, 1970

By J. A. Lamonica

The Bureau of Mines studied two types of approved coal mine dust personal samplers to determine the effect of decreasing the amplitude of airflow velocity fluctuations on cyclone performance. Results indicate that more dust is collected when pulsation free flow is used. Velocity fluctuations were reduced by means of a pulsation damper; damper efficiency of about 85 percent was needed to reduce the fluctuations to an acceptable level. The data were obtained employing both pulsating and non-pulsating flow. A comparison was made of (1) the masses of respirable coal dust as determined by weighing and of (2) the particle size distributions as determined by an electronic counter. An empirical relationship is given between the ratio of masses collected using pulsating and nonpulsating flow (M') and the ratio of the maximum air velocity to the minimum air velocity (V') as measured in the cyclone entrance channel.

Jan 1, 1972

By Marcelo Gagó M.

El presente trabajo señala la factiblidad del método de explotación "Trackless" en la mina Huarón, Pasco a través del sistema de conjunto semi-mecanizado, donde la formación de la unidad de explotación requiere la incorporación de vetas estrechas en arranque selectivo a las vetas anchas. En este sentido, se evalúa la aplicación de vetas con potencias entre 0.40 a 2.80 metros cercanas las unas a las otras, cuya interceptación se sirva de eje, al tiempo que se aproveche de una sola unidad de limpieza.

Oct 14, 1980

By A Turek

The Lake Cinch deposit occurs in the Tazin gneisses on the footwall side of the Black Bay fault. Ore is localized by two faults, the Main Ore fault and the Cracking-stone River fault, occurring in shoots along the former and on tension fractures between the two faults. Faulting leading to the localization of the deposit is analyzed in detail and tied into the regional pattern. Pitchblende, the chief radioactive mineral, is investigated by X-ray and found to be of very small particle size. The relation-ships of U, Fe and Mn in the ore are established quantitatively, and Fe is found to bear a catalytic relation to U. The deposit is classed as belonging to Lindgren's mesothermal class. Mineralization is attributed to carbonate solutions, and the uranium is believed to have been trans-ported in the hexavalent state as the uranyl tricarbonate ion; analogy is drawn to a recently developed hydro-metallurgical technique for the production of uranium dioxide. Introduction THE Lake Cinch deposit is located in the Beaver-lodge Camp, Saskatchewan. The property was staked in 1948 and went into production in 1957

Jan 1, 1965

By Laxman S. Sundae

A U.S. Bureau of Mines designed and fabricated in-seam tester (1ST), retrofitted with a dust shroud, was used to establish a respirable dust index (RDI) and to determine cutting forces from a variety of bit types in four coal mines and a salt mine. Results from cutting tests at four coal mines showed that radial bits required the lowest cutting force and the least specific energy. Generally, for each conical bit the RDI and cutting force increased when the included bit tip angles increased from 70° to 90°. During field tests it was not possible to measure the total quantity of respirable dust produced by each cut; therefore, attempts were made to determine the amount of dust that became airborne from each test cut. The test results show that the quantity of airborne respirable dust is very erratic and cannot be related to bit type. Two statistical methods were employed to analyze RDI, but no correlation was found between the RDI and bit type. Despite scatter in test results for RDI, significant difference was found in RDI generated in four coal seams. In general, RDI increased with the increased cutting force for each coal seam from mine 1 through mine 4.

Jan 1, 1989

By James Paone

The Bureau of Mines made drillability studies with impregnated diamond bits in the laboratory on 7 rock types and in the field on 21 different rock types. Results indicate that drill parameters of rotational speed, thrust, and torque must produce sufficient applied forces to induce stress levels that cause continuous failure in rock to achieve efficient penetration rates. Higher rotational speeds appear to be more effective in drilling relatively harder rocks, although the increased speed causes more bit wear; increases in thrust result in higher drilling rates but not linearly; and up to a critical value a linear relation exists between torque and penetration rate for a specific rock type. Penetration rates with impregnated bits show a trend similar to that obtained with surface-set bits for rock under 25,000 psi compressive strength.

Jan 1, 1966

By J. Howard Bird

The purpose of this publication is to describe the power-distribution system of the mine and refinery of the Duval Sulphur & Potash Company at Carlsbad, N. Mex. This distribution system has been excellently predesigned to meet requirements and fit special conditions encountered at the property. In presenting the material, the authors point out various features that would be desirable for incorporation in other systems under similar conditions. Central location of switchgear in pressurized vaults and ventilation of such equipment with filtered air prevent salt accumulations and contribute to trouble-free operation. The simplification of power-distribution circuits and overload protection, as a result of centralization of switchgear, the use of individual control circuits enclosed in conduit (which aids troubleshooting), and central location of control panels, are factors which contribute to efficient, safe operation. Those features are applicable to many operations where fire or explosion hazards are encountered, or where dusty conditions may exist, as well as in operations where numerous individual drives are involved.

Jan 1, 1959

By J. W. Gálvez

Entre los años 1929 y 1938 se realizaron estudios sobre el problema de los humos en La Oroya y de la construcción del Cottrell de Reverberos, la ampliación del Cottrell de Arsénico y la construcción de las 21 Unidades del Cottrell Central como unidades contrarrestadoras de los humos de mangas y de los convertidores. En ese sentido, el presente texto describe el acondicionamiento de los humos con vapor de agua para ser tratadas en las unidades de precipitación electrostática denominada Cottrell. Para ello, el trabajo se divide en cuatro partes: la primera, describe el circuito de los humos (cobre y plomo) y las unidades de precipitación; la segunda, señala el funcionamiento de la precipitación electrostática; la tercera, refiere los problemas del procesador electrostático y la última, señala la modernización de las unidades de Cottrell.

Nov 20, 1967

By Charles L. Ross

A successful placer mine is being operated by the E. T. Fisher Co. on Rock Creek in the South Pass mining district at Atlantic City, Wyo. About 2,800 cubic yards of gravel is dug daily by a gasoline-driven dragline shovel with a 1 1/4-yard bucket and washed in a movable plant with a gold-dredge trommel and standard-dredge sluice boxes; the total cost is about 12 cents per cubic yard. The gold-bearing gravel occupies a narrow valley between two low ranges, of hills. The ground is covered by brush and willows, which are cleared of in the fall by burning after the leaves have dried. The elevation at the mine is 7,600 feet above sea level.

Jan 1, 1935

By R. C. Emmett

The industrial practice of concentration of solids and production of clear solution by gravity sedimentation is an old technology. Through the years, many devices have been designed and built to aid this process. One of the more significant developments was a revolving rake mechanism to convey settled material to a central discharge point of a circular tank, patented in 1907(1). In recent years, clarification systems employing parallel inclined plates have appeared on the market; the original device utilizing this principle was patented in 1886(2). Numerous other methods have been invented, tested, discarded and sometimes re-invented, all with the specific intention of improving the capacity of a particular settling area. Sedimentation theory, as expressed in Stokes' Law, shows that the rate of settling of a particle is directly proportional to the difference in density between the particle and the surrounding liquid and, more significantly, proportional to the square of the particle diameter. Anything that can increase the latter will greatly assist sedimentation and, as a result, flocculation always has been an integral part of sedimentation. Most materials suspended in aqueous media are naturally flocculent to some degree and, hence, are readily concentrated by sedimentation, although sometimes very slowly.

Jan 1, 1978

By Todd W. Armstrong, Michael D. Reader

"INTRODUCTIONThe Playa Vista Development is the largest urban infill development in the history of the United States. Overall, it encompasses about 1100 acres in the City of Los Angeles and is situated north of Los Angeles International Airport near the Pacific Ocean. The development taking place on the project consists primarily of high-density residential condominiums with 1 to 2 levels of subterranean parking . The geotechnical conditions are typified by high groundwater, soft clays, and liquefaction, in addition to environmental issues such as methane.Due to a combination of the geotechnical factors and noise restrictions, both driven and drilled piles were not feasible once the initial phase of the project was occupied. As a result, the project developer undertook a testing program that consisted of the installation and load testing of 9 piles in order to obtain City of Los Angeles acceptance of a pile installation system that met the site constraints. The testing program was divided between two separate contractors operating on sites set on opposite sides on the street (Figure 1 ). Contractors working in Test Areas A & B employed the ""dry dip"" and ""wet dip"" methods of auger pressure grouted displacement (APGD) pile installation, respectively.This paper summarizes the extraordinary program undertaken to install, document, test, and examine auger pressure grouted displacement piles at this site. The program ultimately resulted in City acceptance of auger pressure grouted displacement piles, a historically difficult challenge given the City's resistance of acceptance of ""new"" technologies.A summary of elements included in the test program are: (1) quality control; (2) load testing; (3) long-term testing; (4) non-destructive testing; and (5) pile exhumation."

Jan 1, 2005

By E. Motica

Ores containing uranium and vanadium minerals have been mined from the Salt Wash Member of the Morrison Formation from many localities in the Colorado Plateau region since about 1900. The most productive deposits are in a relatively small area in Southwestern Colorado referred to as the Uravan mineral belt. The mineral belt is a narrow elongate area in which uranium-vanadium deposits in the Salt Wash have a closer spacing, larger size, and higher grade than those in adjoining areas. Pre- 1948 ore production from the mineral belt was 655,000 tons averaging 1.91 per cent V2O5 and 0.28 per cent U3O8. Production during the 1948 to 1964 period was 7,900,000 tons of ore averaging 1.46 per cent V2O5 and 0.27 per cent U3O8. The ore deposits occur principally in the uppermost sandstone unit of the Salt Wash. This unit consists of sandstone lenses formed by a system of aggrading braided streams flowing in an easterly direction generally normal to the mineral belt. These lenses, referred to as channels, are as much as one mile in width and average about 50 feet in thickness and can be traced for several miles along their courses. Areas favorable for one deposits are recognized principally by the following criteria: ( 1) a host sandstone thickness of over 30 feet, (2) the presence of carbonaceous material in the host sandstone, and ( 3) gray mudstones and clays associated with the ore-bearing sandstone. The ore minerals are believed to have been precipitated from laterally migrating solutions; there is no apparent genetic relationship between ore deposits and tectonic structural features. Exploratory and development drilling from the surface is conducted in three phases: first, wide-spaced drilling to find and outline favorable channels; second, moderate-spaced drilling in favorable ground to locate ore deposits; and third, close-spaced drilling to block-out ore. Long-hole drilling from underground stations is used to find and delineate extensions of ore bodies being mined. Due to intense production since 1948 from shallow deposits, best potential for new deposits exists in areas where the ore-bearing unit is 600 to 800 feet deep.

Jan 1, 1968