Search Documents

By Liu Wenyong, Huang Yucheng, Yang Ba

High-water rapid-solidifying material, called æhigh-water materialÆ, is a new material developed by the authors over many years. The material can solidify nine times its volume of water into solid. The material is a fine kind of binder with special properties. The solidifying body of high-water material with water has quite a high early strength. The compressive strength of the material within three days can reach the same strength as conventional Portland in 28 days. One ton of the material can replace three tons of conventional Portland cement as binder. Some important achievements have been made in application of high-water material. In metal mines, based on the material, a new full-tailing cemented backfill technology has been developed. The characteristic of the new technology is that high-water material is used as binder and full tailing or alluvial sand is used as backfill aggregate. Because of the application of the new technology, major technical problems in backfill technology such as classifying of tailing, dewatering, transportation of pulp, low strength of backfill body, environmental contamination and so on, have been solved.

Jan 1, 1998

By Jorge. Melchiori

En el Perú, la aplicación de los métodos geofísicos para la exploración minera ha sido mínima, a diferencia de las exploraciones de yacimientos petrolíferos, donde su demanda fue mucho mayor. Este diferencia respondería a la poca difusión del mismo, como las escazas pruebas de combinaciones metódicas. Entre los métodos a utilizar, están los sondeos eléctricos verticales y perfiles horizontales), la polarización espontánea( campos eléctricos-naturaleza electroquímica),el método magnético (distribución del campo magnético y perturbación en medición del componente vertical), el electromagnético a inducción(malla horizontal, cuadro vertical), y la emanación en la exploración de zonas mineras (radon, thoron, y actinon).

Jul 20, 1955

By N. Menad

. Electronic wastes are heterogeneous mixture, with mainly copper, aluminium and steel attached to or mixed with various types of plastics and ceramics. In general, small amounts of precious metals are incorporated in this mixture. Today, these components constitute an environmentally problematic fraction in disposal. Their physico-chemical characteristics have been investigated through chemical, x-ray diffraction, infrared spectroscopy, scanning electron microscopy and thermal analysis.

Jan 1, 2000

By Tom Lewis

This report discusses the evaluation of the ENVIRO-CLEAN PROCESS, a technology developed by Lewis Environmental Services, Inc. for the recovery of metals such as chromium, mercury, copper, cadmium, lead, and zinc from surface and groundwater streams. This new heavy metal removal process (patent-pending) utilizes granular activated carbon with a proprietary conditioning pretreatment to enhance heavy metal adsorption combined with electrolytic metal recovery to produce a saleable metallic product. The process generates no sludge or hazardous waste and the effluent meets EPA limits. A 50 gpm system was installed for recovering hexavalent chromium from a ground water stream at a site located in Fresno, California. The effluent from the activated carbon system was reinjected into the ground water table with the hexavalent chromium concentration < 10 ppb. The system simultaniously removed trichloroethylene (TCE) to concentrations levels < 0.5 ppb. The activated carbon is regenerated off-site and the chromium electrolytically recovered. The full scale system has treated over 5 million gallons of ground water since installation.

Jan 1, 1996

By C. S. Ek

As a continuation of previous work, further tests have been carried out to recover silver from the residues obtained in a zinc jarosite process. Selective flotation has been performed with different reagents, and ?cleaning steps have been introduced to upgrade the silver concentrate. Leaching of crude residues, as well as flotation tailings, has been carried out with cyanide and thiourea. Finally, the different beneficiation methods are compared, and the industrial aspects? of their application are reviewed.

Jan 1, 1990

By Robert M. Cox

Surface mining of coal in the South developed into a major industry during the 1960&apos;s. The economic significance of the industry is much greater than is readily apparent when one considers only the value of the coal mined. The abun-dant supply of relatively inexpensive steam coal for electric power generation that has been derived from the surface mines has provided the foundation for the industrial expansion that has occurred throughout the South. The region, in gen-eral, has enjoyed the benefits of plentiful low cost electric power. However, re-cent political decisions, at all levels of government, threaten to destroy or severely curtail the surface mining of coal and eliminate the economic advantages once enjoyed by the region. These political decisions are rapidly changing the basic rules of operation and fundamental economics of surface coal mining. Recent changes, resulting from the enactment of environmental and health and safety laws and various bureaucratic rules and regulations, have had a three-fold effect: 1) Greatly increased operating cost, 2) increased lead times for mine development, 3) limited potential reserve base for future mining. Also current legislative proposals are casting a shadow of uncertainty over the future of all coal mining operations that has created serious delays and in-creased cost for the expansion of the coal industry necessary to meet our project independence goals. Technology Surface mining is the safest and most economical way to produce raw materials from the earth&apos;s crust. It also affords a more healthier working environment for the individual miner. Surface coal mining now accounts for more than 60 percent of the annual coal production in the South. Surface mining of coal requires the removal of the overburden to expose the

Jan 1, 1977

By Ewan Alexander

"As human beings, we have managed risk since the dawn of the ages and have been adept at doing so. In order to survive, we hunted or gathered. If we did not take enough risk, we died. If we took much risk, we died (Fig. 1). As individuals and tribes, risk had to be optimized to maximize our chances to thrive, as individuals and as tribes.In today’s world, the risks are vastly different, but in order to thrive, these must be managed. And no industry knows this as much as mining. In fact, the International Council of Mining & Metals (ICMM) has proposed the Critical Risk Model (Fig. 2) as a means of identifying critical risk, critical controls and associated performance standards. The ICMM focuses on sustainable development performance in the mining and metals industry. It has 23 members, representing some of the largest mining companies in the world.This approach is going to help the mining industry. But it must be applied effectively, with the acknowledgment that the system alone cannot be effective. We can say this confidently, as even companies known for the strength of their risk and safety management systems continue to experience significant incidents, and, in some cases, catastrophes. Why does that happen when all safety metrics, including injury rate, are pointing in the right direction? In the view of the author, it is only when leadership, culture and systems work in complete harmony that the resilience of an organization to manage its significant risk is at an optimal level. It remains an ongoing leadership challenge to maintain that balance and the optimal mindset in the organization. So how do you maintain that special balance?Let’s start with a basic premise. Leadership, supported by simple effective systems, creates culture which creates outcomes. Everyone going home safely is an outcome, as is cost effective operations, and to achieve those outcomes efficiently, the organization must focus on the inputs. And those inputs include effective leadership, effective systems (for the purposes of this article, risk and health, safety and environment (HSE) systems), good planning, stable operations and competent workers. This article will focus on gaining maximum performance from your risk management system."

Oct 1, 2016

By S. Ivanova

The results presented in this paper show that the gold solution dilution is a key parameter to control the dispersion of gold on ?-Al2O3 the selected support. The variation of concentration leads to changes in pH which modify the nature of gold complexes from HAuCl4 formed in the solution. These complexes are presented. Some of them (AuCl3(OH)- and AuCl2(OH)2 -) react with the surface of alumina and give interesting interaction. AuCl2(OH)2 complex has been considered as an ideal complex because of the strong anchorage of a bidentate species on the alumina. This complex is formed mainly in a solution of gold with a concentration of 10-4 M giving a pH of 3.5-4.5. The nature of the anchorage and the amount of chlorine, has an influence upon the formation of Au-Cl bridges which modify the dispersion of the gold on alumina of the final catalyst as shown by TEM.

Oct 1, 2003

By CLARENCE WM. POY

THE most common difficulty faced by an engineer or mine operator when opening a new property in a new field is the lack of roads and of cheap transportation. This one item often swings the balance of success or failure in starting a project. In Alaska, as elsewhere, such problems are more or less serious. In the boom days around the Valdez district, as well as in other parts of this territory, freighting was accom¬plished by dog teams or horses, or even by men that were willing to put their shoulders into harness, because there were virtually no roads. More important, there was only one time when supplies could be transported, and that was when there was suffi¬cient snow on the ground following a heavy wind. Then, and only then, could one depend on the snow to support horses and sleighs, and be sure that the gulleys, streams, and crevices in the glaciers were filled with snow to avoid pitfalls. These methods were used when one had no roads, no streams in the summer to float a barge, or even a trail for a pack train. If the snow was deep and soft, trans

Jan 1, 1935

By JULIAN HINDS

Industrialization is raising the standard of living of people everywhere. The common man is demanding and getting more of everything. Perhaps more markedly than most other things, he is consuming more water. A hundred years ago water for domestic use, in all but a few large centers, was lugged from wells in buckets. This still is true in many rural areas, even in the enlightened United States of America. but pumps and pressure systems are rapidly replacing the "old oaken bucket," even on farms and in isolated country homes. Nevertheless, many still fail to see water as a ?commodity? in the same sense that coal, lumber, fertilizer, and bread are considered as commosities. Water is too frequently taken for granted.

Jan 1, 1949

By Evandro Tolentino

As fibras vêm sendo empregadas nos materiais de construção civil desde o início da humanidade. No começo da década de 50 houve o início da utilização de fibras de aço no reforço de matrizes de cimento. Com isso foram notadas alterações no comportamento do material, sendo detectado o aumento da tenacidade pós-fissuração. Esta é uma pesquisa experimental que teve como objetivo a definição de parâmetros de ensaios para a produção de argamassas de cimento Portland, que utilizem fibras de sisal nas suas composições, tratadas quimicamente por acetilização com intuito de reduzir a absorção de água. O sisal (Agave Sisalana) apresenta boas propriedades físicas e mecânicas. As fibras foram cortadas manualmente nos comprimentos de 20 mm. As diferentes composições de argamassas foram produzidas com 0,2% e 0,4% de fibra de sisal, em relação ao volume total da argamassa. Estudou-se o comportamento mecânico dos compósitos com ensaios de resistência à tração na flexão. Os resultados mostraram uma melhoria na resistência à tração na flexão para argamassas com fibras tratadas quimicamente por acetilização.

Oct 30, 2017

By A Annor, L J. Chen

The production of paste backfill has typically been accomplished through the adaptation of existing technology. Thickeners and disc filters have several drawbacks when applied to production of tailings paste backfill. Personnel at CANMETÆs backfill research laboratory in Sudbury, Ontario, Canada have been carrying out research into and development of methods to produce paste backfill using total mill tailings since 1991. Using a silo for production of paste is not a new concept but has been refined to a marketable level. This technology is based on a fluidization principle that assists in settling the tailings to an homogenous state in a silo. Other developments include patented de-watering technology for use in the silo to speed the settling of the solids to a suitable solids content, optimisation of silo geometry, and instrumentation related to paste backfill production and transportation. The advantages to fluidisation technology are in reduced capital cost, reduced operating costs and in the environmental benefits of using full plant tailings over classified tailings or alluvial aggregates. Another major advantage is in the ability of this technology to be retrofitted to existing hydraulic backfill plants to further reduce capital cost. This paper details the development of the new technology as well as the associated cost savings over other technologies. It will also look at the research and development of unique components that make this technology work.

Jan 1, 1998

By Alexandra Yuyali

The objective of this research work is to increase the drilling ratio represented in tons per drilled meter (ton/m) to reduce mining costs. One of the key characteristics of this research is the use of the ITH (in-the-hole) drilling rig with a water-powered hammer, also known as Wassara™. The patented Wassara™ in-the-hole hammer is powered by high-pressure water instead of air. To reach the objective, a new design of the blast pattern was implemented considering the following: Burden from 1.7 m (5.6 ft) to 2.8 m (9.2 ft) Spacing from 1.7 m (5.6 ft) to 2.7 m (8.9 ft) Drill diameter from 89 mm (3.5”) to 102 mm (4”) Drilling length from 15 m (49 ft) to 30 m (98 ft) Borehole deviation < 2% The result of this new design is the optimization of the drilling ratio (ton/m); having as a baseline 5.2 ton/m with traditional equipment and obtaining 13.7 ton/m with the ITH drilling, which generates annual savings of $2.43M.

Jan 21, 2025

By Joaquim Luiz Monteiro de Barros, Fabiana Moreira Costa

Este trabalho tem como objetivo principal apresentar de forma didática e através de exemplo prático, os processos de limpeza de gases de exaustão durante a produção de ferro e aço para atendimento as normas ambientais e a possibilidade da recuperação de energia térmica desses gases captados para aumento da eficiência energética das plantas siderúrgicas.

Aug 1, 2019

By G. Chisakuta, P. Bwando, G. Mitshabu

By the end of 2022, the south-eastern Copper Belt region of the Democratic Republic of Congo was host to more than 40 small, medium, and relatively large sized copper solvent extraction sites. To date, solvent extraction reagents supplied in this region have never exceeded 50% of ketoxime content. We generated laboratory extraction and strip isotherms and used these with the BASF IsocalcTM modelling software to assess the benefit of using higher ketoxime blends on the main metallurgical performance indicators such as copper recovery and net transfer. Pure ketoxime extractants combine a relatively low strip point and a decent loading capacity, which are most effective as the pH of the pregnant leach solution gets closer to 2.

Jan 1, 2023

By X Dahe

SLon vertical ring and pulsating high gradient magnetic separators possess excellent mineral processing ability and have been widely applied to process oxidised iron ores. SLon centrifugal separators are applied to clean the SLon magnetic concentrate and remove quartz and other gangue minerals associated with a small portion of magnetite.This paper introduces the application of this technology in Hai Nan, Da Hong Shan and An Shan for processing oxidised iron ores.

Jul 11, 2011

By Fadi Layyous Gedeon, David Hatton, Solomon Mogashoa, Tuhin Banerjee, Faisal Aljohani

The adoption of innovative technologies in mineral processing often raises concerns about complexity and integration. However, Woodgrove’s Direct Flotation Reactor (DFR) technology at Barrick’s Jabal Sayid copper concentrator provides a different perspective. This paper outlines the smooth integration of DFR technology from piloting to full-scale commissioning, showcasing how easily the cells were brought online. Installed in a cleaner scalper role, DFR cells at Jabal Sayid upgrade re-ground rougher concentrate to final concentrate in one stage. Despite processing challenging ore, the DFR cells delivered concentrate grades that consistently exceeded expectations. The commissioning process was straightforward with minimal hurdles, highlighting the technology's user-friendly nature. This paper advocates for a shift in perceptions about new technologies in mineral processing. The success of DFR technology at Jabal Sayid demonstrates that “different” doesn’t mean “difficult.” By focusing on ease of commissioning and operational integration, innovative solutions can enhance processes, improving efficiency and productivity in the mining industry.

May 4, 2025

By Monica C. Pinto, Gustavo H. Nalon, José C. L. Ribeiro, Rita de C. S. S. Alvarenga, Leonardo G. Pedroti, Lucas A. F. Fioresi

This study aims to evaluate the influence of mortar’s mechanical properties on the behavior of clay masonry. Experimental studies were performed using prisms of clay blocks under axial compression. The clay units were produced with a clay from Tres Rios, Rio de Janeiro, Brazil and had compressive strength of 4.9 MPa. Two mortar compositions were used, which had compressive strength of 94.7 and 50.4% of the clay blocks’ net area compressive strength. It was noticed a slight increase on the prism’s compressive strength with the increase of the mortars’ compressive strength and stiffness. Prisms made with flexible mortars had a ductile failure and collapsed under lower compressive stresses, while prisms made with stiff mortars resisted higher compressive stresses, but had a brittle failure ,crushing the blocks. A very strong mortar is not recommended. Using more flexibl mortars does not compromise the strength and stiffness of the masonry and prevents an excessively brittle failure of the structure.

Mar 1, 2017

By H. H. Yancey

In this information circular is presented a summary of the more important articles that nave appeared in the literature pertaining to the experimental work and to the commercial operation of the froth-flotation and Trent processes as applied to the cleaning of fine coal.

Jan 1, 1933

Jan 1, 1995