Search Documents

By Jankola W. A, Delong O. J

Historically, the silica content of zinc concentrates treated at Cominco's Trail Operations has been low. Silica in the roaster calcine seldom exceeded 1.5 per cent because of the low silica content of concentrate from Cominco's Pine Point mine. With the shutdown of Pine Point, alternate sources of concentrate were required and it was anticipated that calcines containing greater than two per cent silica (with excursions above three per cent) would have to be treated. Previous experience indicated that the existing leaching circuit could not tolerate such high levels. Therefore, a research program was undertaken to identify the key factors affecting silica precipitation; to compare different process alternatives; and to make recommendations for modifications to the existing plant. A project to modify and upgrade the leaching circuit has now been completed. Calcines with higher silica contents are successfully treated, but the upper limit of the circuit is unknown. The results of the research work will be discussed and the new leaching plant will be described. Recent operating results will also be presented.

Jan 1, 1993

By Caroline Gerwig, Joseph R. Wickline, Zach Agioutantis

In longwall mining, the progressive caving of the roof allows stored energy to dissipate over an extended time. However, in some cases, the roof strata above the longwall panel are unusually strong and do not break with the movement of the working face. Instead, the roof material bridges over the expanse of the longwall, forming an unstable beam. Later, when this beam breaks, the stored energy can release suddenly, causing a seismic event to propagate to surrounding mine workings. The focus of this paper is to estimate the size of beams that form over longwall panels to the seismic energy recorded by the mine. Analytical calculations are used to verify two-dimensional models of longwall roof beams to determine the strain energy and gravitational energy developed, which is then released upon strata failure to surrounding mine workings. Models are developed using RS2 to model the stress, strain, and deflection along the bottom of the longwall roof beam to calculate gravitational and strain energies. Gravitational energy is shown to be the main driving factor in energy release, except for the beams with low heights. Analyses allow the determination of beam characteristics based on seismic data. The analysis is refined using swelling factor to compare various beam drop heights. The models show an increase in seismic magnitude for higher drop heights. However, the actual data provided by the Buchanan mine displays a decrease in seismic magnitude with increasing drop height, indicating that energy is dissipated into the broken gob material as drop height increases.

Jul 1, 2023

By M. SIDDARAJU, Rameshwar Sah, T. Umadevi, K. S. SRIDHARA, B. D. Ganesh Shetty, M. RAJU

The production of high strength iron ore sinter for blast furnace iron making unit was developed by optimizing the granulometry of less than − 0.150 mm fines in sinter base mix which consists of iron ore fines (− 10 mm size with 0.150 mm: 41%), beneficiation plant jig concentrate, i.e., washed ore (− 3 + 0.150 mm size with − 0.150 mm 3 to 9%), beneficiation plant concentrate (− 0.150 mm size 97%), limestone, dolomite, coke breeze, lime, sinter return fines, direct reduced iron (DRI plant) fines, and micropellets produced from steel plant waste. The sintering process consists of preparation of base mix, mixing, and production of nodules using mixing and nodulizing drum by maintaining the optimum moisture, transferring of nodules to the sintering machine, and firing of sinter by applying optimum suction pressure. To optimize the < 0.150 mm fines in sinter base mix, the − 10-mm size iron ore fines was replaced with washed ore. The size analysis, granulation index (G index), and optimization of moisture w.r.t. sinter bed permeability were carried out by varying the washed ore addition from 0 to 55% in sinter base mix to vary the − 0.150 mm fine size. With decrease in washed ore addition from 55 to 0% in sinter base mix the finer fraction, i.e., − 0.150 mm in sinter base mix increased from 9.4 to 26.7%. Granulation (G) index increased from 1.46 to 3.10, sinter bed permeability increased from 33 to 53 Japanese Permeability Unit (JPU), and balling index increased from 1.4 to 3.0. With increase in − 0.150 mm fines in the sinter base mix from 9.4 to 26.7%, the sinter tumbler index (T.I) increased and sinter reduction degradation index (RDI) decreased. Increase in sinter strength and decrease in sinter RDI was due to increase in formation of Silico ferrite of calcium and aluminium (SFCA) phase and decrease in pore phase. The SFCA is the main bonding phase in iron ore sinter, and it provides strength to sinter. Sinter base mix with − 0.150 mm fines 18.9% (washed ore addition 25%) achieved desired sinter properties with moisture 8.0%, G index 2.44, balling index 2.3, and sinter bed permeability > 45JPU. Decreased the sinter properties with washed ore addition in sinter base mix beyond 25% due to decrease in − 0.150 mm fines in sinter base mix. Further, to improve the sinter properties with washed ore 30 to 45%, 3 to 10% beneficiation plant concentrate, i.e., − 0.150 mm fines was added to maintain the 18.9% of − 0.150 mm fines in sinter base mix. From the laboratory sintering studies, it was found that minimum 18.9% (range from 18.9 to 26.7%) − 0.150 mm fines should be maintained in the sinter base mix to achieve desired sinter properties.

Oct 16, 2021

By J. B. Mawdsley

Introduction The writer was instructed to visit the Chibougamau region during the field season of 1927 and report on the mineral discoveries that had been made there since 1911. lt was deemed advisable to obtain detailed information regarding the rocks underlying the area in the vicinity of these recent discoveries. Accordingly an area 60 square miles in extent was mapped. The outcrops were studied along the water courses and along bush traverses spaced at half-mile intervals between these water courses. The completion of the rest of the summer&apos;s programme allowed only three weeks for this work. lt is from this small, mapped area, and this necessarily cursory survey, that the material for this paper was obtained. Location And Means Of Access The name Chibougamau district is applied loosely to an ill-defined area of about 1,000 square miles lying mostly north and west of Chibougamau lake in the Province of Quebec. The lake is approximately half way between lake St. John and James bay. It lies 150 miles north of the Canadian National railway and 40 miles south of Mistassini?lake.

Jan 1, 1928

By E. Swartzman

"IntroductionGENERALLY, the necessity for mining coals of higher impurity content, the drive for lower costs by intensive mine mechanization, changing market requirements, and the increasing competition of oil and natural gas, have continued to result in an upward rise in coal preparation, and have necessitated a more intensive study of coal preparation problems.Increasing adoption of •continuous mining equipment, for example, is introducing new problems in coal preparation. Limited experimental work in the United States (1) shows that the effect of the continuous miner on size distribution varies with the characteristics of the seam. In some seams, the fines problem is lessened, in others it is greatly aggravated. Generally there is a decrease in the relative amount of the top sizes (plus 2 in.) and a substantial increase in the intermediate sizes (down to about 1/8 in.). Contrary to expected results•, where continuous miners with vertical-moving cutting heads are used, an increase in impurities in the slack sizes does not necessarily occur where draw-slate is taken. This is because the draw-slate tends to be kicked out in lump form. However, if a seam contains bands •and lenses of impurities they are bound to be in the mined product."

Jan 1, 1952

By Manuel Cabrera Melendez

Actualmente las explotaciones en la pequeña minería producen exclusivamente minerales de alta ley puesto que cubre el costo de los fletes y las maquilas, dejando de lado los minerales de alta ley. En esta perspectiva, el texto plantea una alternativa técnica y económica que mejore las condiciones anteriormente planteadas a partir del uso del carbón activado para así beneficiar los yacimientos de baja ley y optimizar el desarrollo minero aurífero de nuestro país. Así también la tecnología del carbón activado reduce los costos de operación puesto que se da una versatilidad del tratamiento de minerales, genera mayor recuperación del oro y mejora su productividad.

Nov 24, 1986

By C. Chapman, M. G. Reading, M. P. Amsden

Ecstall Mining Limited, a subsidiary of Texasgulf Incorporated, operates the Kidd Creek mine, a 10,000- tpd base metal producer, near Timmins, Ontario. Two different ore types are mined and milled copper-zinc and silver-lead-zinc. At the highly automated Ecstall concentrator, the ores are processed by selective flotation in three individual circuits. One of the most important metallurgical tools for process control is a sample system incorporating continuous onstream X-ray analysis. Recently this system was further automated by adding computer control of reagents for two copper-zinc flotation circuits. The computer programs, utilizing optimum seeking methods and smelter contract terms, have increased copper recovery 0.8% and zinc recovery 1.6%, and reduced reagent costs by 12%. Although not anticipated, copper and zinc concentrate grades were improved modestly as well.

Jan 1, 1973

By M. M. Tilman

The Bureau of Mines conducted research to determine the feasibility of strengthening experimental magnesium-base sheet alloys by strain softening induced by controlled cold rolling followed by selective heat treatment. Relatively small alloying additions having potential for producing strain softening were selected from metals that are readily avail-able. Tensile properties comparable to minimum properties of the most commonly used magnesium-base sheet alloy AZ31B, in the H24 condition (strain-hardened and partially annealed), were obtained in an Mg-IMM (mischmetal)-O.5Mn alloy after strain-softening rolling followed by heat treatment. Tensile properties of the experimental alloys in certain conditions are also compared with minimum tensile properties of other standard magnesium sheet alloys. Incidental to the principal objectives, apparent superplastic behavior was observed in three experimental magnesium-base alloys containing MM, MM plus manganese, and MM plus zirconium.

Jan 1, 1985

By R. H. King

Suboleski and King (1990) analyzed the reasons for the dramatic increase in underground coal mine productivity during the last 10 years. This paper examines whether this increase can be extended. The paper forecasts whether the mix of technological, procedural and other factors that produced the increase will change in the future. The forecast is based on the base case and spreadsheet production model described in the previous paper.

Jan 1, 1991

By Luis Mercado

El presente texto revisa laas posibilidades, problemas y soluciones respecto del carbón peruano donde se busca mejorar sus posiblidades y desarrollo para el beneficio del país. Así también se revisa la sustitución del petróleo por carbón mineral en la industria siderúrgica, sustitución del petróleo por carbón mineral en la industria del cemento y sustitución en Cementos Lima y Cemento Andino, el uso del carbón mineral en ladrilleras en hornos cerrados.

May 1, 1987

By G. S. Hume

THE Plains of east-central Alberta herein described embrace an area from Viking east to the Saskatchewan boundary and from North Saskatchewan river south to Coronation and Monitor (Figure 1). By far the greater part of this area is deeply drift-covered, and .outcrops of bedrock are relatively few and often widely separated. Within the area there are large morainal hills and others of considerable extent that superficially have all the characters of morainal hills but contain a core of bedrock. These latter, then, were hills when the ice sheet traversed the country and only have been modified by glacial agencies. In many places on them, the drift is but a thin veneer, as is certainly the case in part of the Neutral hills (Figure 2) northeast of Coronation and north of Monitor. In other cases, however, as in the Blackfoot hills, southwest of Lloydminster, the drift is sufficiently thick to conceal practically all the bedrock and in many places no information is available as to whether a bedrock core, representing a pre-glacial hill, is present. There is no question, however, that the larger river valleys, as for example those of the North Saskatchewan and Battle rivers, are in part at least pre-glacial. Proof of this can be demonstrated in many places, because obviously the valleys must have been present in pre-glacial times to allow glacial deposits to have accumulated in them. It is also known that inter-glacial deposits occur. At one locality in Battle River valley, in sec. 30, tp. 45, range 2, west of the 4th mer., the following section occurs( l ): 15 feet of boulder clay with granite and other boulders. 56 feet of stratified sands, clays, and gravels containing pebbles of Precambrian rocks and fresh-water shells. From this it is apparent that the 56 feet of stratified sands, clays, and gravels must have derived their Precambrian pebbles from a previous glaciation of which the overlying boulder clay represents another ice advance in this area. Thus, although the river valleys contain glacial and interglacial deposits, they have not been filled by them to such an extent that the drainage has been diverted, and in many places, especially in the case of Battle river and some smaller streams, the size of the valley is altogether out of proportion to the size of the stream it now contains.

Jan 1, 1937

By David F. Gearhart

A cooperative study was conducted between Signal Peak Energy and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the behavior of a pre-driven recovery room under less than 200 ft of cover. The design of the support systems for a pre-driven recovery room must provide control of the roof and ribs during the changing stress environment experienced throughout the final advance of the longwall into the recovery room. It must also provide a stable area where mine personnel are not exposed to undue hazards during shield recovery operations. This recovery room was constructed in two phases; each phase mined a 21-ft-wide room that was heavily supported, and subsequently fully backfilled with 800-psi, cellular concrete. Instrumentation to monitor the recovery room performance included borehole pressure cells (BPCs) placed in the head gate and tailgate pillars, at four locations across the longwall panel, in the fill material, and in the first row of outby pillars near the center of the panel. Four roof-to-floor convergence sensors were installed in the back fill material and a vertical, multipoint borehole extensometer (MPBX) measured the displacement of the strata above the recovery room. Surface surveys were conducted to measure MPBX collar movement. The data show that the front abutment load was transferred onto the recovery room backfill and the out by pillars as the longwall panel was extracted. As the longwall approached the recovery area, the fender and shields yielded, but the backfill provided enough support to keep the room stable as the longwall advanced to its final position. The system worked as planned and the face was recovered in record time.

Jan 1, 2014

By Thomas W. Thompson

The Zebulon manganese deposit has been known for a number of years. It is situated about 3 miles east of Zebulon, Wake County, N. C., on the Avon, Privett property (fig. 1). The deposit outcrops as a vein, or dike averaging-16 to 20 feet in width. Drilling by the Bureau of Mines has shown that this outcrop results from consolidation of a number of small stringers near the surface. The surface width and the Percentage of manganese oxides (resulting from. weathering) diminish with depth. Below 50 to 80 feet, the vein material is mainly quartz and spessartite garnet. The deposit was first examined by W. T. Benson, a Bureau of Mines engineer, in 1941. The Bureau conducted a diamond-drilling exploratory program an the property from November 7, 1944, to January 25, 1945. A. total of 2,508.5 feet was drilled in 14 holes along the strike of the deposit.

Jan 1, 1950

A revolutionary development in blasting materials has occurred in recent years. Ammonium nitrate, sensitized by the addition of a small percentage of No. (class) 2 diesel fuel or other suitable petroleum product, has been adopted as a low-cost, efficient blasting agent2 in a wide variety of mining, quarrying, and heavy construction operations. Moreover, the ready availability of the component supplies throughout the Nation, together with the ease of formulating them into effective blasting agents, has made it possible for the blaster himself to prepare the mixes at the site of use. Recently, most established explosives manufacturers have begun supplying premixed AN-FO (ammonium nitrate-fuel oil) or a comparable product to various mining operations. However, many individuals and small business establishments are marketing premixed products prepared in facilities that are often poorly constructed and poorly located. Although these blasting agents have partly or wholly displaced explosives such as dynamites in many applications, there are some blasting operations in which the fuel-sensitized ammonium nitrate agents do not appear to be well adapted. As long as the hazards they present are clearly understood and respected, ammonium nitrate-based blasting agents have important safety characteristics when prepared under competent factory control or field-mixed under equivalent close control. This publication attempts to summarize the knowledge of those hazards and to incorporate practical ways to cope with them.

Jan 1, 1963

By MARSHALL D. DRAPER

THERE are said to be about 150 operating companies in Kotchiu, most of these being small, corresponding in degree to lessees in western mines in the United States. Of the total number there are probably forty large companies having their own smelting plants equipped with one or two furnaces, slag crushing plant and other accessory equipment. A few plants, not more than ten, do custom smelting. There are in all about fifty smelting plants in Kotchiu. With little variation, the equipment and methods are the same. The plant usually consists of two furnaces, one being in operation while the other is being relined 01- re- paired. An adjoining house contains one or more of the large buffalo-drawn Chilean mills for crushing slag. A few houses for the working coolies, with more pretentious ones for the owners, complete the establishment, the whole being surrounded by a compound wall 8 ft. high.

Jan 1, 1931

By D. E. Hirsch, J. W. Davis, Norman G. Foster, F. G. Schwartz

This investigation was undertaken to identify nitrogen , oxygen , and sulfur compounds (polar components ) found in catalytically cracked distillate fuel . It is significant that these compounds concentrate in the sediments and gum that form when the fuel is stored . The polar components were divided in three portions by elution from a chromatographic column filled with alumina . After the hydrocarbons were washed through the column with pentane , a benzene eluted extract was removed followed by an ether eluted extract and then an alcohol desorbed fraction . These extracts were individually distilled in a molecular still and the fractions were analyzed by gas chromatography , mass spectrometry , infrared spectrometry , and elemental and functional analyses . Naphthalene and its homologs , phenanthrene and its homologs , and other compounds such as methyl indene , C₂ quinolines , phenyl indan , and the benzothiophenes , appear in the benzene extracts . Quinolines are the major components of the lower boiling fraction of the ether extract , although carbazoles , acridans , and indoles are present in some concentration . Elemental and functional group analyses of the alcohol fraction indicated 10 percent of the distillate portion was nonhydrocarbon , and in this portion the average molecule contained more than one nonhydrocarbon element . Compounds of such complexity are not well known , and standards for positive identification are limited .

Jan 1, 1963

By H. B. Humphrey, F. E. Cash

The Southern Appalachian coal field extends southward across Tennessee in a belt about 50 miles wide between the eastern and middle sections of the State. The earliest record of the production of coal in Tennessee is for 1840, and the first inspection laws were passed in 1881. In 1887, a second act of the legislature created the office of Chief Inspector, but little was done until 1891 when a new act was passed giving to the Department of Mines added duties and powers. Since that time, except for the years 1915 to 1918, com¬ prehensive annual reports have been published. Data for the tables given in this paper are taken from these annual reports, from those of the Southern Appalachian Coal Operators' Association, and from the publications of the United States Bureau of Mines, which has main¬ tained a station at Jellico, Tenn., since 1911. Complete figures for 1930 are not available yet and they are not included in the averages. The State Department of Mines, the operating companies, and the United States Bureau of Mines cooperate in accident-prevention work. It is the purpose of this report to present in uniform tables the available statistics in regard to fatal accidents in Tennessee and in the coal mines of the United States, in order that the progress in mine safety in Tennessee may be compared with that of the country as a whole, and the present period may be compared with various periods of the past, to indicate the main points of attack in the reduction of accidents.

Sep 1, 1931

By Pierre Buteau

Peat/ands distribution in Canada is widely spread thoughout the country and corresponds to a wide spectrum of wetland habitats which overlay peat deposits. The development and the evolution ofpeat/ands and peat deposits are closely linked together, since the vegetal remains of the peat deposits originate from the peatland habitats, and the peatland habitats constitute a response to many factors, including the properties of the substrate, which are the peat deposits. Peat/ands are defined as waterlogged terrains where the production of plant materials usually exceeds the rate of decomposition. The underlying peat deposits consists of organic residues associated to peatland vegetation, more or less decomposed, built up and kept under anaerobic conditions. Peat/ands evolution and distribution are determined primarily by climatic factors, but also by the geomorphology and edaphic conditions. All of these create particular hydrodynamical environments which will vary according to different regional settings, and sequentially to an evolutive time frame.

Jan 1, 2001

By Harold L. Gibson, Don H. Rousell, Ian R. Jonasson

"Abstract - The Sudbury Structure consists of three major components: 1) the Sudbury Basin; 2) the Sudbury Igneous Complex which surrounds the basin as an elliptical collar; and 3) an outer zone of shatter-coned and intensely brecciated footwall rocks. Although the Sudbury Event which formed the structure may be unique, the area has, in fact, been shaped by a series of tectonic, magmatic and mineralization events which can be considered in terms of two Wilson cycles of continental extension and closure. The first cycle, from 2500 to 1700 Ma, included the following events: doming (uplift of Levack Gneiss Complex); NE-SW extension (Matachewan dikes); N-S to NW-SE rifting (faults, mafic intrusions, sedimentation, and Ni-Cu-PGE and U mineralization); NW-SE extension (Nipissing diabase, and Ni-Cu-PGE, Ag, Co mineralization); and NW-SE and NE-SW closure (Penokean Orogeny, 1900 to 1700 Ma) with superimposed meteorite impact (1850 Ma, Ni-Cu- PGE, Zn-Cu-Pb deposits). The second cycle, from 1700 to 1000 Ma, included: N-S extension (alkali metasomatism, Au); N-S extension (hornblende diabase dikes along the Murray fault set); NNESSW extension (olivine diabase dikes); NE-SW extension (Fecunis Lake fault set); and NW-SE closure (Grenvillian Orogeny).The rich and diverse Ni-Cu-PGE and subordinate Zn-Pb-Cu and Au mineralization of the Sudbury region is related to endogenic and impact-triggered crustal extension and magmatism. The Sudbury Structure apparently was the site of a triple junction or hot-spot. The Sudbury ores, although located within an impact structure, are analogous in terms of age and tectonic setting to Ni-Cu-PGE and Zn-Pb-Cu ores elsewhere in the world. Meteorite impact accentuated on-going ore forming processes and magmatism at Sudbury."

Jan 1, 1997

By Harold L. Gibson, Don H. Rousell, Ian R. Jonasson

"The Sudbury Structure consists of three major components: 1) the Sudbury Basin; 2) the Sudbury Igneous Complex which surrounds the basin as an elliptical collar; and 3) an outer zone of shatter-coned and intensely brecciated footwall rocks. Although the Sudbury Event which formed the structure may be unique, the area has, in fact, been shaped by a series of tectonic, magmatic and mineralization events which can be considered in terms of two Wilson cycles of continental extension and closure. The first cycle, from 2500 to 1700 Ma, included the following events: doming (uplift of Levack Gneiss Complex); NE-SW extension (Matachewan dikes); N-S to NW-SE rifting (faults, mafic intrusions, sedimentation, and Ni-Cu-PGE and U mineralization); NW-SE extension (Nipissing diabase, and Ni-Cu-PGE, Ag, Co mineralization); and NW-SE and NE-SW closure (Penokean Orogeny, 1900 to 1700 Ma) with superimposed meteorite impact (1850 Ma, Ni-Cu- PGE, Zn-Cu-Pb deposits). The second cycle, from 1700 to 1000 Ma, included: N-S extension (alkali metasomatism, Au); N-S extension (hornblende diabase dikes along the Murray fault set); NNESSW extension (olivine diabase dikes); NE-SW extension (Fecunis Lake fault set); and NW-SE closure (Grenvillian Orogeny).The rich and diverse Ni-Cu-PGE and subordinate Zn-Pb-Cu and Au mineralization of the Sudbury region is related to endogenic and impact-triggered crustal extension and magmatism. The Sudbury Structure apparently was the site of a triple junction or hot-spot. The Sudbury ores, although located within an impact structure, are analogous in terms of age and tectonic setting to Ni-Cu-PGE and Zn-Pb-Cu ores elsewhere in the world. Meteorite impact accentuated on-going ore forming processes and magmatism at Sudbury."

Jan 1, 1997