Search Documents

By Brij M. Moudgil

Separation of oil shale from waste material or into high grade and low grade fractions can have a major influence on the economics of the surface (ex-situ) retorting process. Different components of shale rock vary significantly in physical and surface chemical properties such as specific gravity, color, water wettability etc. Various techniques which utilize the difference in one or more of the above propartis have been proposed to preconcentrate the oil shale before retorting. A discussion of the techniques proposed such as gravity separation, sorting and froth flotation is presented.

Jan 1, 1982

By Hidenori Hatta, Takero Watanabe, Hideo Yoshida

"The effect of the quenching rate on age hardening in an Al-6.0mass%Zn-0.75mass%Mg alloy sheet was investigated. The quenching rates and aging conditions were as follows: water quenching (WQ) or furnace cooling (FC) followed by pre-aging at 20°C,then artificial aging at 120, 160 or 200°Cwere performed. The peak strength of the FC and the WQ are very similarat120°C aging. It is important high strength was obtained even at the extremely slow quenching rate. On the other hand, the strength of the WQ significantly decreased compared to the FCat200°C aging. GP(I) zones were formed during the pre-aging at 20°C even if the cooling rate was very slow like the FC, and were transformed into the GP(II) ones at 70°C or higher and then into the ?’ phase. However, these zones were dissolved by reversion during heating to 200°C. Thus the strength of the WQ decreased. On the other hand, it is considered that an unknown cluster or GP zone with a thermal stability formed during the FC was not dissolved up to 200°C and was transformed into the ?’ phase. Therefore, a higher strength was obtained in the FC for the200°Caging.INTRODUCTIONAl-Zn-Mg alloys are widely available in commercial production because these alloy have lower quench sensitivity and can be produced by air cooling (AC). Heat treatable aluminum alloys are usually produced by water quenching (WQ) to increase their strength because a high cooling rate inhibits the precipitation of the stable phase during cooling and increases supersaturated solute atoms. However, Baba(1967)reported the strength of an Al-6%Zn-1.8%Mg(mass%) alloy without additional elements quenched by very slow cooling (15°C/min) was 96% of that quenched by WQ. Furthermore,the age hardening at room temperature (RT) occurs after annealing at 410°C followed by furnace cooling (FC, 0.5ºC/min or less)in these alloys. Therefore, the process of annealing at 410 to 430°C for 120 min followed by AC, and reheating at 230°C for 240 min, then cooling is recommended in the specifications (Japan Aluminum Association, 2011). Matsuda and Yoshida(1996)also recommended annealing at 300°C for Al-Zn-Mg alloy extruded products to inhibit age hardening at RT by precipitating the solute atoms and decreasing them in the matrix. It has been considered that the higher the content of excess quenched-in vacancy becomes by WQ, the higher aging rate at RT is obtained. Therefore,it is theoretically and commercially important to clarify the reason why the age hardening occurs relatively quickly in almost no excess quenched-in vacancies such as the FC, and why the same strength as the WQ can be obtained in the FC"

Jan 1, 2018

By M Sykes

Gold was initially discovered at Ballarat in 1851. After initial alluvial mining, underground quartz mining commenced in 1853, continuing until 1918. The historic miners were considered to be capable of mining anywhere in the world after overcoming the difficult conditions within the Ballarat goldfields. Whilst mining has changed dramatically since the early 1900s the challenges with underground mining at Ballarat have not. Modern pumping systems cope with the moderate water inflows. However, modern machinery and efficient mining methods influence opening sizes and extraction techniques. In some cases modern techniques have accentuated the challenging ground conditions and complex orebodies that were faced by the historic miners. As the Ballarat East project has progressed towards production, technical challenges relating to geomechanics and mine planning are being resolved resourcefully.

Jan 1, 2008

By D. M. Lewis, J. K. H. Ma, Y. Rojanasakul, J. Y. C. Ma, J. H. Kang, V. Castronova

"Tetrandrine is a bisbenzylisoquinoline alkaloid which has been shown to exhibit antifibrotic activity against silicosis. Tetrandrine is characterized by its strong binding to alveolar macrophages and inhibition of particle-induced respiratory burst activity in these phagocytes. In contrast, tubocurine and tubocurarine are structurally similar to tetrandrine but exhibit little effect on fibrosis or activation of alveolar macrophages. The objective of the present study was to test the effect of tetrandrine on macrophage production of monokines in response to occupational dusts, and to determine tetrandrine's effect on monokine-medicated cell growth using a mouse thymocyte proliferation assay and lipopolysaccharide (LPS) as a positive control. Stimulation of alveolar macrophages by respirable silica dust resulted in a release of monokines which caused a fourfold increase in thymocyte proliferation. Coal dust, on the other hand, had no effect on macrophage production of this cytokine. Tetrandrine was found to exhibit a dose-dependent inhibition of monokine release from both silica and LPS-stimulated alveolar macrophages. In experiments where thymocytes were directly treated with tetrandrine, a dose-dependent inhibition of thymocyte proliferation was noted with both interleukin-1- (IL-1) specific and nonspecific mitogenic (concanavalin A) actions. In contrast to the inhibitory potency of tetrandrine, tubocurarine was found to have no effect on either the production of monokines by LPS-stimulated alveolar macrophages or IL-I-mediated thymocyte proliferation. These results provide a correlation between the ant:fibrotic effect of tetrandrine and inhibition of macrophage activation. INTRODUCTIONThe pathogenesis of chronic pulmonary fibrosis caused by inhalation of occupational dusts has been associated with abnormal activation of alveolar macrophages such as the release of various cytokines capable of inducing fibroblast proliferation and collagen synthesis. These macrophage-derived cytokines include interleukin-1 (IL-1), tumor necrosis factor (TNF), platelet-derived growth factor (PDGF), transforming growth factor-B (TGF-(B), macrophage derived growth factor (MDGF), and interferon [1, 2].Interleukin-1 is a major macrophage-derived cytokine that has been shown to exhibit multiple biological effects on a variety of target cells. It is known to cause leukocyte [3, 4] and endothelial cell activation [5, 6], and to affect the synthesis and maintenance of the extracellular matrix by stimulation of fibroblast proliferation [7-9], synthesis of collagens [10] and gluco-saminoglycans [11], and prostaglandin E2 production [12]. In addition, IL-1 plays an important role in the initiation of an immune response through its direct activation of lymphocytes and stimulation of the production of other cytokines, such as interferons and hemopoietic colony-stimulating factors, needed for the expression of an immune response [13]. As a major cytokine in the immune-inflammatory sequela, IL-1 is also produced by epidermal, epithelial, lymphoid, and vascular tissues after infection, injury, or antigenic challenge [14]. Agents such as lipopolysaccharide (LPS), phorbol myristate acetate (PMA), immune complexes, and particulates are known to activate the synthesis and release of IL-1 by monocytes and macrophages [15]. These substances also trigger intracellular signals leading to altered arachidonic acid metabolism. Although the mechanism is still not clear, prostaglandins have been shown to suppress IL-1 translation via the induction of cyclic adenosine-monophosphate (CAMP), whereas leukotrienes produce a positive signal for IL-1 production [13]."

Mar 1, 1992

By T Raynlyn, S Hapugoda, V Nunna

The predominant phase in most Marra Mamba, channel iron deposits and detrital iron ore deposits is goethite. Goethite abundant iron ore fines tend to have complex mineralogical associations and fine dissemination of gangue material. These ores are typically challenging to process using conventional beneficiation methods. With declining ore grades, there is a need to develop new processing routes for low-grade goethitic ores/fines.Comparative process amenability studies were carried out using two different processing options to recover iron with low alumina and silica content from a low-grade goethite-abundant iron ore fines (-2 mm) sample from the Pilbara region of Western Australia. The first option involved dehydroxylation at 350°C and 400°C, followed by grinding dehydroxylated samples to 100 per cent passing 106 µm and magnetic separation. The second option was processing raw sample by gravity separation using a Floatex density separator. The performances of the two processes are discussed in terms of the iron grade-recovery responses, and an optimal processing route is proposed based on the findings from these tests.CITATION:Nunna, V, Hapugoda, S and Raynlyn, T, 2015. Process amenability studies on goethite-abundant iron ore fines, in Proceedings Iron Ore 2015, pp 165–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Broggi Andrea

Condensates produced by SiO(g) and CO(g) have a crucial importance in silicon production. Condensation will follow the reactions 3 SiOðgÞ+COðgÞ→ 2 SiO2 + SiC and 2 SiO ðgÞ→Si+SiO2. Solid compounds generated during silicon production contain Si, SiO2 and SiC in different microstructures and amounts. In industrial systems, condensates limit the SiO(g) escape to the off-gas system. On the other hand, they can block the gas flowing from the high temperature zone, hence the necessity of studying an optimized condensation process. This review discusses SiO(g) condensation and its interaction with CO(g). The report gives an overview of the condensates found both at laboratory and at industrial scale. The two main compounds are the Si–SiO2 and the SiOx–SiC mixtures. The hypothesis on the mechanism of formation of SiC–SiOx condensates is presented through a wide selection of performed works. The advantages and disadvantages of the former experimental procedures are discussed.

By M. H. Thomas

El presente trabajo describe tres ejemplos de empresas en Australia que utilizaron carbones provenientes de fuentes locales para el encendido de sus hornos. Así también se muestra los principios generales de la operación de los hornos rotatorios, la quema de combustible pulverizado, el encendido directo e indirecto, la contaminación de cenizas y los problemas derivados de la eliminación de azufre.

Nov 1, 1984

By R. E. Siemens

A process is being developed by the Bureau of Mines to selectively recover nickel and cobalt from low-grade domestic laterites. In laboratory evaluation of the process, the oxides in the laterite were selectively reduced with carbon monoxide at temperatures from 350° to 600° C. For material containing more than about 5 percent magnesia, pyrite additions or post-reduction heat treatments were necessary to achieve satisfactory nickel and cobalt extraction for this range of reduction temperatures. Multistage leaching of the reduced material at ambient temperature and pressure in the presence of oxygen, ammonium sulfate, and ammonium hydroxide extracted up to about 90 and 85 percent of the contained nickel and cobalt, respectively. The nickel was selectively recovered from the leach solution by solvent extraction and was then stripped from the loaded organic with dilute sulfuric acid to provide a nickel-rich electrolyte. Treatment of the raffinate with hydrogen sulfide resulted in the recovery of cobalt as a sulfide. The only contaminant in solution was magnesium which was removed by ion exchange or precipitation. In this process the energy requirements are relatively low and except for minor operation losses, only coke and oxygen are consumed.

Jan 1, 1975

By Mark C. Russell, Charles T. Russell, Brooke Colburn, Parker Bailey, Desiree Bernhard, Kaito Durkee, Tristen Cutshall, Rob P. H. Urselmann

Hypersonic tunnel boring (HTB) uses directed, high velocity projectile impacts to remove rock. HTB is highly independent of rock strength and targets hard, abrasive rock and variable rock environments. This paper discusses history, theory and presents test (2×2 m and .75×.5 m tunnels) field trial results and technical and economic evaluation. The HTB tests are compared against the historic ‘project REAM’ and the concept against tunnel boring machines and drill & blast in design studies for full-scale 12 m and 4.5×5.5 m tunnels. The positive results indicate that under these conditions HTB can replace Drill & Blast and Tunnel Boring Machines.

Jun 13, 2021

By J. H. Westbrook, R. W. Guard

The influence of a number of alloying additions on the structure and hardness of Ni3Al (?') has been studied. Three general effects have been observed.. solid-solution hardening, strain aging, and defect hardening arising from deviations from stoichiometry. The solid-solution hardening phenomena are complicated relative to binary terminal solid solutions due to the possibility of virtually independent substitution for the component elements and to the concomitant effects of strain aging. In many superior nickel-base high-temperature alloys the elevated temperature strength is attributable to the presence of a dispersion of Ni3A1 (?') in a solid-solution matrix. Examples of such alloys are Inconel X-550, Inco 713, Waspalloy, and Nimonic 80. It is, therefore, appropriate to seek a further understanding of the properties and alloying behavior of this compound. Ni3Al, the compound most rich in nickel in the nickel-aluminum binary system, was first detected by litakal but not established with certainty until the much later studies of Bradley and Taylor' and Alexander and Vaughan.3 More recently the mechanism of formation was clarified by Floyd4 who showed that Ni3Al is the product of a peritectic reaction at 1395°C between the melt and the compound NiAl in agreement with the original suggestion of Alexander and Vaughan.3 Ni3Al has the ordered face-centered-cubic or Cu3Au structure in which the nickel atoms occupy the face centers and the aluminum atoms the cube corners, a0 = 3.570A. Despite earlier reports to the contrary. the compound apparently remains ordered at least to 1000oC.5 It exists over a narrow range of compositions (-3 pct wide) whose limits and temperature dependencies thereof have been reviewed recently by Taylor and Floyd.' Most previous workers have found Ni3Al to be both hard and brittle7,8 although Maxwell and Grala8 obtained 2.5 to 6 pct tensile elongation at room temperature and Alexander and vaughan3 described the material as "hard and tough" on the basis of observations made while preparing metallographic specimens. In a recent study one of the present authors found that although considerable intergranu-lar brittleness was evident: individual grains of a coarse-grained inert atmosphere arc-melted specimen were readily deformable.l0 The same study also showed Ni3Al to have an anomalous temperature dependence of hardness in that such a curve exhibits a number of peaks between room temperature and 800°C which could not be associated with any microscopically observable precipitation reactions or polymorphic transformations. It was, therefore, proposed in the present study to elucidate the anomalous high-temperature strength behavior and to examine the solid-solution alloying of this compound and the effects of such alloying on hardness. Sample Preparation and Experimental Procedure-Samples, both of pure Ni,Al and of various alloyed solid solutions based on Ni3Al, were prepared by arc melting 100-g buttons in an inert atmosphere arc furnace. All buttons were heat treated for 4 hr at 1275oC and examined metallographically for homogeneity. Microstructures were typically homogeneous and single phase with ASTM grain size about 1 and unusually clean grain boundaries. Chemical analyses showed good correspondence (within a few tenths of a percent) with intended compositions. Microindentation hardness data were obtained from room temperature to 800°C in vacuo using a balanced-beam type loading system in an instrument to be described in detail elsewhere." In general a 100-g load, a loading rate of 1 mm per min and an indentation time of 15 sec were used. Various indenter materials were used according to the materials bein tested because of specimen-indenter interaction. Fl Measurements of the Vickers-type indentations were made at room temperature. Hardness-temperature curves were run at least twice on each sample to ensure that surface work-hardening effects had been eliminated." Precision lattice-parameter measurements were made on powder samples using a back-reflection

Jan 1, 1960

By J. P. Gliddon

Since 1980 a number of significant changes have been introduced at Palabora in an effort to off-set the effects of reduced product price and increased unit cost of inputs. These changes and improvements include major equipment rationalization programs, the introduction of trolley assisted truck haulage, adoption of a sophisticated computerized truck control system, pit design enhancements, improved drilling practices, use of emulsion explosives and the installation of an in-pit crushing and conveying system. The various changes, their effect on the operation and their contribution to cost reduction and improved productivity at Palabora are considered.

Jan 1, 1987

By R. A. Wildenboer, R. F. Sandenbergh

Rare earth elements (REE) are present at concentrations of approximately 0.36 % in phosphogypsum stacks located in Phalaborwa, South Africa. The REE are present in the phosphogypsum in solid solution in the gypsum and as fluorine and aluminium rich precipitates. Recovery of the REE offers opportunities for valorization and reducing the environmental impact of the phosphogypsum waste. This paper presents the results of investigations into the leaching behaviour of rare earth elements and other impurities from phosphogypsum using aqueous sulfuric acid. The effects of acid concentration, temperature, residence time, and the influence of impurities were evaluated for their impact on the solubility of rare earth elements in a sulfate medium. It was found that a significant fraction of the REE can be leached from the phosphogypsum in a range of conditions much less severe than traditional hard rock rare earth processing conditions. The REE were leached at a sulfuric acid concentration of 110 g/l, temperature of 30°C – 40°C and a residence time of approximately 8 hours.

Nov 6, 2024

By V. E. Homme, M. M. Wong

Tests were made in reactors ranging from 12 to 30 inches in diameter to develop methods for the preparation of sodium chloride - titanium lower chlorides ( dichloride and trichloride ) melts that contain titanium predominantly in the divalent state . Such melts are desirable as a starting material for the production of titanium metal or as an electrolyte for electrorefining of titanium . Sodium reduction of TiCl with an 18 - hour period of holding the reaction products in the molten state produced melts that contained titanium lower chlorides in TiCl₂ - to - TiCl , molar ratio of approximately 8 to 1. Sodium reduction of TiCl in a reactor with a shielded pipe weir , that required no melt -holding period , produced melts with a TiCl₂ - toTiCl , molar ratio as low as 4 to 1 . Reduction of TiCl4 with scrap titanium metal in molten sodium chloride produced relatively pure melts containing about 27 percent titanium in a Ticl₂ - to - Ticl , molar ratio of approximately 4 to 1 .

Jan 1, 1964

By A. C. Fieldner, G. W. Jones

Tests were made at the Government Fuel Yard , operated at Washington , D. C. by the Bureau of Mines , Department of the Interior , in order to determine and improve the adjustment of the carburetors on the trucks used for transporting coal from the Fuel Yard to the different Government buildings in Washington . The tests were made possible through the hearty cooperation of G , S. Pope , engineer in charge of the Fuel Yard . Joseph Burrows and A. E. Foote of the garage department assisted during all the tests and supplied information on the mileage obtained by the trucks for the months preceding and succeding the time the tests were made . The Mack trucks used range in capacity from 2-1/2 to 7-1/2 ttoonnss .. The majority of the carburetors were Stromberg G- 3 type , as shown in Table 2. During the winter months , when the demand for coal is heavy , from 30 to 35 trucks are used . At the time the tests were made , only about ten of the trucks were in daily use , owing to the small demand for coal during the summer months , and scarcity due to labor conditions . Samples of the exhaust gas were taken on the trucks kept in service for summer hauling in order to determine the carburetor adjustment as used . Changes were then made to a more economical adjustment wherever possible , without sacrificing flexibility of operation and power . In every case the adjustments were maintained for maximum power , but were adjusted to the leanest position to give that power . In all but one case the carburetors were found to be adjusted too rich for maximum power and economy . These results are considered in detail in a later part of this report .

Jun 1, 1923

By H. Han, Z. Gao, Y. Gao, W. Sun, J. Wang

Strategic Ca-bearing minerals like scheelite and fluorite are usually separated by flotation, yet the separation is quite difficult due to their similar surface Ca active sites. Compared with the conventional strong collector sodium oleate (NaOL), lead nitrate-benzohydroxamic acid (Pb-BHA), complex collector shows a better selectivity for scheelite, yet its high cost hinders its wide application. Therefore, a novel collector (Pb-BHA-NaOL complex) was initially developed in this work to overcome the abovementioned dilemma. The flotation results of a single mineral showed that Pb-BHA-NaOL had a better selectivity for scheelite than Pb-BHA. Under the conditions of sequential assembly of Pb, BHA and NaOL at the molar ratio of 240:120:1 and pH 9.0, selective separation of scheelite from fluorite could be achieved without adding any depressants. In addition, for the same preferred scheelite recovery, Pb- BHA-NaOL could also save approximately 20% Pb and BHA compared with Pb-BHA. The analyses of the zeta potential measurement and X-ray photoelectron spectroscopy indicated that Pb-BHA-NaOL showed stronger adsorption on scheelite relative to fluorite. Meanwhile, Pb-BHA-NaOL showed more adsorption modes and higher utilisation of Pb and BHA on scheelite than Pb-BHA, which was due to the accelerator, NaOL. Keywords: Scheelite, fluorite, lead nitrate, benzohydroxamic acid, sodium oleate, flotation

Jan 1, 2020

By Jon Y. Kaneshiro, Eric Dawson, Pooyan Asadollahi, Steven Hunt

This paper provides updates to the paper published by the lead author at RETC 2011 with a summary of developments in technologies, products, and approaches to corrosion analyses of gravity sewer tunnels and microtunnels. This paper presents approaches in evaluating degradation of reinforced concrete liners. Also, the carbon footprint of conventional concrete liners and alternative “green” liners are compared and their life cycle costs are considered. A few case histories from the past decade are provided indicating the latest and emerging trends in liner protection.

Jun 13, 2023

By T Ireland

The Project Hobson tunnel excavation was the first use in New Zealand of an earth pressure balance (EPB) tunnel boring machine (TBM). The tunnelling on the project was very successful and break-through was achieved three weeks ahead of program, demonstrating that tunnelling can be undertaken in Auckland with a high degree of cost certainty.Project Hobson involved the replacement of an existing 90 year old above ground sewer that crosses Hobson Bay in Auckland, New Zealand, and which had reached the end of its economic life, with a 3 km long, 3.7 m internal diameter segmentally lined bored tunnel. The NZD$ 118 M project has provided several environmental benefi ts to the Owner, Watercare Services Ltd and the local community:· provide capacity to meet projected growth in the region,· virtually eliminate wastewater overflows into Hobson Bay and the Waitemata Harbour, and· remove an obtrusive visual feature and open up the bay for recreational purposes.Auckland’s bedrock is a weak sandstone/siltstone (East Coast Bays Formation), subject to infilled paleovalleys. The geology in the region has been significantly influenced by volcanic activity; 49 volcanoes are present within 20 km of the city centre.The paper describes the design and construction challenges for the projects, including TBM performance, ‘sticky spoil’ management, and risks associated with basalt lava flows and two paleovalleys. The paper also highlights the reasons for the success of the project, including a rigorous approach to risk management during design, and effective planning during construction. Other useful data such as the effect on the watertable caused by closed face tunnelling, and ‘faceloss’ estimates derived from settlement arrays are included in the paper.Project Hobson also saw the successful implementation of a Geotechnical Baseline Report – one of the first uses of this type of document in Australasia.

Mar 8, 2011

By Oliver Bowles

Lime is of tremendous importance to modern industries. In agriculture it is regarded as essential to the continued fertility of many important regions; in building it is indispensable, and in the many ramifications of the chemical industries it is so necessary and so widely employed that it has been designated "the king of all the bases." Figure 1 shows a general view of a modern lime plant producing more than 500 tons of lime daily. In 1924 the production of lime was reported from nearly every State in the Union and amounted to more than 4,000,000 tons, valued at, nearly $40,000,000. For a production of that magnitude between 8,000,000 and 9,000,000 tons of limestone are required. The many problems involved in winning this great quantity of raw material from the natural rock and preparing it for the kilns have in the past received little attention from any governmental agency. Therefore, in compliance with a request from representatives of the National Lime Association in 1922, the Bureau of Mines began a study of problems in limestone quarrying in an effort to advance more economical methods of operation and the utilization of waste material. Field studies were made at many quarries, and the information thus compiled, besides data already at hand from work in other branches of the stone industries, were disseminated to operators in the form of mimeographed Reports of Investigations, eight of which were issued at intervals during 1922, 1923, and 1924. A questionnaire was appended to each report, and quarry operators were invited to contribute additional information obtained as a result of their actual experience and observation. Operators of lime plants have been cordial in their responses and have supplied the bureau with much valuable information. From the data thus obtained, supplemented by later field studies, the revised reports have been combined to form the major part of this bulletin, which is believed fairly to represent present knowledge on the subject of quarrying limestone for lime manufacture.

Jan 1, 1927

By W. H. Ode

An investigation of standard methods for determining ash in low-rank* coals showed that generally 60 to 95 percent of the total sulfur in the coal is retained in the ash as SO3. This large sulfur retention causes a positive error in the determined mount of ash of as much as 6 percentage points for the coals examined, although it usually is 2 to 3 percentage points for lignites and about 1 for subbituminous coals. Unless the sulfur content is low or unless a correction is made for the SO3 retained, the fixed carbon and oxygen have an equivalent negative error when determined by difference; also other inaccurate analytical values occur when the data are calculated on an ash- free bas is. No simple modification of the ashing procedure was found that would reduce the sulfur retention to a point where its effect on the ash determination would not be significant, Therefore, for accurate analytical work on law-rank coals, the SO3 should be deducted from the determined ash to obtain a "corrected" ash value.

Jan 1, 1962

By P B. Hills, R J. Walton

Geotechnical instrumentation has been implemented as a key step for monitoring and optimising an engineered mine design for managing seismicity at the Beaconsfield Gold Mine. Measurements of displacement, stress change, ground control element load and seismic response of the rock mass allow for back analysis and calibration of critical parameters for feedback into the engineering design loop. Instrument clusters are installed in strategic locations prior to the commencement of stoping in order to determine the nature of the response of the rock mass to stoping. A selection of instruments including instrumented cable bolts and rod extensometers, resistance wire extensometers, hollow inclusion stress cells, vibrating wire stress meters and resistance wire extensometers are used to gather data through a data logging system. The rate at which data is recorded is adjusted to provide more information during periods of anticipated rapid change such as around stope firings or during periods of high seismic activity, and less information during periods of anticipated quiescence. The twofold purpose of the instrumentation is to calibrate the numerical modelling output which forms the basis of the engineered mine design, and to provide an alert mechanism where the behaviour of the rock mass is not what was anticipated, or where the impact of that behaviour may compromise the integrity of the engineered ground control system. The paper describes the location of instrument clusters with respect to stoping, the type of instruments employed and the method of data acquisition. It provides examples of results obtained and illustrates the way in which that information is used to optimise the mine design and manage seismicity.

Jan 1, 2008