Search Documents

By Morgan M. Sears

The LaModel program is widely used to calculate stresses and displacements on thin tabular deposits, particularly when multiple seams or complex mining geometry is encountered. The program itself allows the user to create multiple mining steps to show a progressive sequence of mining. However, LaModel considers each individual step as an independent steady-state condition, and any previous loading conditions of the materials are not tracked. It also does not consider any sort of dynamic stress change during the mining process. In certain circumstances, especially in multiple-seam situations, modeling a scenario of the seam of interest without considering the previous mining sequence in the off seams can potentially lead to inaccurate results. The primary objective of this paper is to present a situation where a potentially dynamic, unstable mining condition was encountered. It was not evident until the previous loading conditions in the off seams and the impact of dynamic stress changes in the active seam were considered. It is important to make the mining community aware of these potential modeling scenarios where the path-dependent nature of the mining sequence is of key importance. This paper presents a case history where room-and-pillar retreat mining was being conducted in a relatively deep cover stress regime where multiple seam interactions were present from both undermining and overmining. Mining in the active seam was being conducted with roomand- pillar mining techniques consisting of a series of parallel production panels being successively developed and retreat mined along a set of Mains. In this situation, the traditional global LaModel analysis without any path-dependent adjustments did not fully identify the area of poor conditions that were encountered. This paper explores the impacts of mining in the active seam on the lower seam which, in turn, has a negative impact on the active seam. This provided a solid foundation for the subsequent analysis of the three seams simultaneously. Based on the calibrated model, it is likely that retreat mining in the active seam resulted in increased stresses in the underlying seam that conceivably resulted in additional convergence and, most likely, additionally convergence of the pillars under the panel being developed. This in turn could have caused active subsid- The LaModel program is extremely useful for analyzing multiple-seam mining scenarios. As multiple-seam situations become even more prevalent, the potential for encountering a path-dependent mining scenario also increases. To successfully model path-dependent mining scenarios, the ground control engineer will be required to make sound judgments on the condition of pillars in sub-adjacent seams. These engineering judgments should be based not only on the current state of stress, but also on any prior or future states of stress. This means considering the stresses from over or undermining as well as stresses applied to the sub-adjacent seams from actively mining the seam of interest.

Jun 25, 2024

By WENDY MARTIN

The Eastern Townships and Asbestos Hill areas are the current asbestos-producing districts of Quebec. Mining in the two areas began in the /are 1870s and 1972 respectively. Production from the Eastern Townships is derived from rhe Serpentine Zone of ulrramafic rocks, specifically from basal serpentinized peridotite members of what are now considered to be allochrhonous ophiolitic material that was abducted onto the Early Ordovician continental margin. From south west to northeast, the rhree allochthonous asbestos-producing sections of the Serpentine Zone are designated the Asbestos Ophiolite Complex, the Thetford Mines Ophiolite Complex and the Pennington Dyke; the Pennington Dyke is considered to represent a segment of serpentinized Alpine peridotire that was fragmenred from a larger, more complete ophiolire complex. The Asbesros Hill deposir on the Ungava Peninsula lies in what apparenrly is an inrrusive sill found wirhin rhe Chukorar Group, the uppermosr group of Precambrian-aged Cape SmithWakeham Bay Belr of volcanic-sedimentary rocks.

Jan 1, 1984

By Nikhil Dhawan, Shrey Agrawal, Veeranjaneyulu Rayapudi

India’s steel vision of 2030 requires a huge amount of quality iron ore. The utilization of low-grade iron ores such as banded iron ores will play an important role to achieve the same production. The absence of alumina impurities in the banded hematite jasper (BHJ) ore provides it an edge over other low-grade iron ores. The conventional beneficiation techniques such as magnetic separation and washing were found to be ineffective to produce suitable feed (Fe ~ 60%) for the blast furnace. It was found that microwave exposure provides significant enrichment to the low-grade iron ore and can be used as a pretreatment step in the beneficiation of similar low-grade iron ores. The above study reveals that hematite phase is susceptible to microwave exposure which enhances the separation of iron values from impurities. Under optimum conditions, an iron-enriched concentrate with 61% Fe, 85% Fe recovery at 50% yield can be achieved from BHJ feed ~ 38% Fe. The pretreatment process for BHJ beneficiation includes only microwave exposure without any chemical additive and may prove economical and industrially feasible.

Refractory gold concentrates often contain submicroscopic gold that is encapsulated within the crystal matrix of iron sulfide minerals, such as pyrite, pyrrhotite and arsenopyrite. To recover the gold, the host mineral must generally be broken down chemically by oxidative processes, such as roasting, pressure oxidation or bacterial leaching, which expose the gold for subsequent recovery by leaching in cyanide solution. The focus of attention in these pretreatment processes is usually the oxidation of the sulfides to elemental sulfur, sulfur dioxide gas or sulfate ions. Less attention is paid to the deportment of iron and the changes in its oxidation state, although this can have a profound effect on gold and silver liberation, as well as downstream operating costs. Iron sulfide minerals break down completely during pressure oxidation, and dissolve in the sulfuric acid solution that is gener-ated from oxidation of the sulfides. This dissolution liberates the tiny gold particles that were originally trapped in the sulfide crystals, and gold recovery during subsequent cyanidation is usually very high (>95%). Iron goes into solution in the oxidation process, initially as ferrous sulfate, but this compound is rapidly oxidized to ferric sulfate, which then hydrolyzes and reprecipitates. The form of the precipitate varies depending on the operating conditions in the autoclave and the presence of certain metal cations. When the acidity in the autoclave is quite low (<20 g/L H2SO4) and the temperature is high (>200°C), the formation of hematite is favored. When the acidity is high (>20 g/L H2SO4) and the temperature is relatively low (160 to 200°C), the formation of basic iron sulfate is favored. If the ore or the leach solution contains significant levels of certain cations (such as Na+, K+, NH4+, Ag+ or Pb2+) and the acidity is high (>20 g/L H2SO4), jarosite compounds are favored. Hematite is the desired iron product in the autoclave discharge, for both metallurgical and environmental reasons, but it is difficult to operate an autoclave under the conditions required for effective liberation of gold without converting some of the iron to basic iron sulfate and/or jarosite. These compounds fall into a category of iron compounds known generically as iron hydroxy sulfates, all of which can cause significant processing and environmental problems in the downstream gold process. This paper deals specifically with basic iron sulfate: the conditions under which it is formed in an autoclave, the problems that are caused by its presence in the feed to a cyanidation plant and possible remedial strategies that can be adopted, both in the autoclave and downstream.

Jan 1, 2010

Refractory gold concentrates often contain sub-microscopic gold that is encapsulated within the crystal matrix of iron sulphide minerals such as pyrite, pyrrhotite and arsenopyrite. To recover the gold, the host mineral must generally be broken down chemically, by oxidative processes such as roasting, pressure oxidation or bacterial leaching, which expose the gold for subsequent recovery by leaching in cyanide solution. The focus of attention in these pre-treatment processes is usually the oxidation of the sulphides to elemental sulphur, sulphur dioxide gas or sulphate ions. Less attention is paid to the deportment of iron and the changes in its oxidation state, although this can have a profound effect on gold and silver liberation, as well as down stream operating costs. Iron sulphide minerals break down completely during pressure oxidation, and dissolve in the sulphuric acid solution that is generated from oxidation of the sulphides. This liberates the tiny gold particles that were originally trapped in the sulphide crystals, and gold recovery during subsequent cyanidation is usually very high (>95%). Iron goes into solution in the oxidation process, initially as ferrous sulphate, but this is rapidly oxidized to ferric sulphate, which then hydrolyzes and re-precipitates. The form of the precipitate varies depending on the operating conditions in the autoclave and the presence of certain metal cations. When the acidity in the autoclave is quite low (<20 g/L H2SO4) and the temperature is high (>200OC) the formation of hematite is favoured. When the acidity is high (>20 g/L H2SO4) and the temperature is relatively low (160 to 200OC), the formation of basic iron sulphate is favoured. If the ore or the leach solution contain significant levels of certain cations (such as Na+, K+, NH4+, Ag+ or Pb2+) and the acidity is high (>20 g/L H2SO4), jarosite compounds are favoured. Hematite is the desired iron product in the autoclave discharge, for both metallurgical and environmental reasons, but it is difficult to operate an autoclave under the conditions required for effective liberation of gold without converting some of the iron to basic iron sulphate and/or jarosite. These compounds fall into a category of iron compounds known generically as iron hydroxy sulphates, all of which can cause significant processing and environmental problems in the downstream gold process. This paper deals specifically with basic iron sulphate; the conditions under which it is formed in an autoclave, the problems that are caused by its presence in the feed to a cyanidation plant, and possible remedial strategies that can be adopted, both in the autoclave and downstream.

Jan 1, 2010

By M. -H. Fillion

"Geotechnical stability analysis and design in open pit mines requires access to representative geological, structural, hydrogeological, and rock mass models. The quality and quantity of collected geomechanical data used to build such models can have significant implications in the design of safe and economically viable slopes. Data collection is a continuous process throughout the life of a mine. The process starts from exploration to conceptual/preliminary feasibility, feasibility, design and construction, operations (early production/late production), and mine closure.As geomechanical data is often limited at an early stage of a project, the estimated variability of the geotechnical factors may be larger than the actual data variability. This can potentially result in a conservative selection of the pit slope angle. Collecting additional geomechanical data at later stages of the mine development may contribute to reducing the uncertainty associated with the geotechnical properties and a steeper slope angle may be used for the design. This can result in significant economic benefits.This paper investigates the impact of access to new data over time, following a series of geomechanical data collection campaigns, on design decisions. This is illustrated by comparing the resulting slope design, at three stages of the mine project, at a South African open pit mine. To demonstrate this, a series of slope stability analyses were performed using limit equilibrium tools. For each project stage, the slope angle design was modified until a similar probability of failure of 5% or less was obtained. The corresponding factor of safety distributions for each project stage were then compared to evaluate the impact of collecting additional data on the resulting slope design.The results showed that data variability can differ significantly from one project stage to another. Data variability may be greater at more advanced project stages (i.e. a wider distribution of the factor of safety). Furthermore, the results showed that, even for the cases with greater variability, steeper slope angles were possible at more advanced stages for the proposed design requirement (probability of failure < 5%). In this investigation, as more data became available, the uncertainty associated with data variability could be sufficiently reduced to allow the selection of less conservative slope angles. This can be used as a managerial tool in developing data collection strategies and allocating the necessary funds, and can lead to important economic benefits to the mining operation."

Jan 1, 2016

By F. F. Peng

A unique collector dispersion techniques was developed and used to improve the flotation rate and recovery of coarser and ultrafine coal-rich particles in the froth flotation processes. In this novel collector dispersion method, the collector such as hydrocarbon-oil is gasified and transported by gas phase (air stream) into the pulp. In addition to the excellent mode of collector dispersion, the collector-encapsulated air bubbles are generated in the pulp. This approach alters the surface properties of air bubbles and provides the fast rate of flotation compared to that of direct liquid collector addition froth flotation. Using gasified kerosene as the collector, the effect of altering surface properties of bubbles on the recovery of larger and finer coal-rich particles of -1.7 mm (-12 mesh) and -600 µ m (-30 mesh) raw coal samples were studied. The Redstone seam coal obtained from Northern Central region of West Virginia was used in this work. The effect of particle size on oil-coated bubble flotation rate and recovery were also evaluated. The conventional froth flotation test with a liquid form of kerosene addition was also conducted for comparison purpose.

Jan 1, 1991

By Leonard P. Vitt

This report details the work done to provide the U.S. Bureau of Mines with a customized Wireless Ground Monitor Wireless Ground Monitor was modified as follows: 1. A voltage regulator was added to prevent false trips with line voltage variations. 2. A Ground Wire Trap was designed to eliminate problems with parallel paths and provide spark suppression. 3. A three phase filter was designed to reduce 60 Hz leakage current. 4. A portable tester was designed to permit complete test of installed systems. 5. The design was modified to insure trip with an open ground wire in the event of a failure of any one semi-conductor component.

Jan 1, 1976

By Atmesh K. Sinha

The demand for thermal coal both nationally and internationally is projected to increase rapidly. The marketability of high ETU thermal coal produced in the USA is, however, limited by its high sulfur content. Fortunately, over 70 percent of the sulfur exists in pyritic form. The research conducted at Southern Illinois University indicates that over 90 percent of the pyrite can be removed by simple devices such as concentrating tables, cyclones, or froth flotation cells and the desulfurized coal can be blended with low sulfur western coal to produce EPA compliance coal. Thus, both the low BTU western coal and the high sulfur midwestern coal can be rendered competitive in the utility markets, here and abroad due to improved utilization.

Jan 1, 1983

By George T. Motock

In Germany the extraction of lithium and its salts has been handled mainly by units of the two major concerns - Metallgesellschaft A, G. and Deutsche Gold und Silber Scheide Anstalt, both with headquarters in Frankfurt. Zinnwaldite, which belongs to the mica group, is the major source of the lithium-containing raw material in Germany. Lepidolite and amblygonite also are used when available, but they are imported, as there are no major deposits of these two minerals in Germany.

Jan 1, 1946

By T Raynlyn, A Edenton, M Adam, R J. Holmes, J R. Manuel, N Ware, R Smyth

Due to ongoing demand and increasing depletion of high-grade iron ore resources from large deposits, Australian iron ore producers are developing smaller size deposits to maintain current export levels. The iron grade, mineralogy, chemical and physical characteristics of iron ore fines being mined from different deposits vary considerably. It is therefore imperative to develop long-term strategies to maintain the quality and consistency of iron ore fines while moving to a larger diversity of smaller deposits. Blending is a common practice in sinter plants as it is almost impossible to produce a high performance sinter mixture displaying the required characteristics from one single ore. Blending is also one of the most effective options being used by iron ore producers to ensure the long-term stability of their products while increasing production. When designing a blend, the blend components are selected to support each other to achieve the required overall balanced metallurgical performance of the final product at a relatively low cost. To do so, a fundamental understanding of the key characteristics of iron ore fines and their potential impacts on the iron ore sintering process and sinter quality are required. In this paper, the sintering process and sinter structure have been analysed and the key factors affecting the sintering performance of iron ore fines, including productivity and quality, identified. Under fixed sintering conditions, the granulation efficiency, nuclei stability and the volume and properties of the primary sinter melt are believed to have important impacts on both sintering productivity and sinter quality. Discussion is then focused on the effects of ore chemical, physical and mineralogical characteristics on the key factors identified and in turn the consequences for sintering productivity and sinter quality.

Jan 1, 2009

By P. D. Kovscek

The Bureau of Mines equipped a longwall shearer with a water-jet-assisted mechanical cutting system to determine the effect of the high-pressure sprays on machine performance, airborne dust levels generated, and size of particles formed. Testing was conducted on a simu-lated coal block (coalcrete) while cutting at a water pressure of 190 psi and at water-jet-assisted pressures ranging from 1,000 to 6,000 psi. The shearer motor energy used by the shearer while cutting coalcrete was determined for each cutting condition. Results indicate that the motor energy required by the shearer for each ton of material cut did not vary significantly as the water pressure was increased. Results of dust measurements recorded near the cutting drum indicate that at water pressures above 3,000 psi, dust reductions up to 85 pct were achieved com-pared with cutting with conventional sprays. Analysis of the particle size distribution during cutting showed that increasing the water pres-sure resulted in increased median particle size. In light of these results, various mechanisms for water-jet-assisted cutting are discussed.

Jan 1, 1986

By K. L. Paciorek

The aim of the present study is to determine on a gram per gram basis the toxic products of the thermal oxidative degradations of selected compositions. Four families of materials were investigated under the subject contract namely polyvinyl chloride and neoprene compositions, rigid urethane foams I and woods. Three methods were employed to conduct the thermal oxidative degradations: a sealed system (quiescent environment) I a stagnation burner arrangement (dynamic environment) I and a flow-through apparatus (dynamic I but less severe than stagnation burner conditions). The majority of tests were conducted using the first two systems; only limited experiments were carried out employing the third decomposition procedure. All decomposition was done at temperatures of 370 -4000C I the higher temperature being used in the stagnation burner. It has to be stressed that the nature of the products and the relative product concentration are temperature dependent. Thermogravimetric and differential thermal analyses were performed to supplement and extend the above delineated studies and to explore the feasibility of using these analyses as a method for material differentiation.

Jan 1, 1973

By R. L. Miller

The potential for recovery of enriched uranium from spent nuclear fuel which has been consolidated into a nuclear waste form was explored in the studies reported here. The waste form of interest is iron-enriched basalt (IEB)--a silicate-based, fused-cast ceramic. IEB samples were prepared containing fuel assembly materials that simulate the core debris of Three Mile Island Unit II;1,2 the nominal composition of the consolidated waste form is given in Table 1. Ore Types The IEB samples, or man-made uranium ores (MMUO), are in two different mineralogical forms. Each MU0 was made by melting the constituent materials and holding at about 1500°C for 1 h. The MMUOs were then heat treated to control crystallization and crystal growth and then cooled to room temperature.

Jan 1, 1983

By William G. Pariseau

A small displacement-small strain finite element technique utilizing the constant strain triangle and incremental constitutive equations for elastic-plastic media that are nonhardening and obey a Coulomb yield condition has been applied to the analysis of gravity flow initiation in a V-shaped hopper containing a powder under lunar environmental conditions. Three methods of loading were examined. Of the three, the method of computing the initial state of stress in a filled hopper prior to drawdown by adding material to the hopper layer-by-layer is superior (as expected). Results of the analysis of a typical hopper problem show that the initial state of stress, the elastic moduli, and the strength parameters have an important influence on material response subsequent to the opening of the hopper outlet.

Jan 1, 1971

By V. K. Karra

An improvement in the present day screen sizing methods calls for knowledge on i) how material in the size range: 0.5 x 1.5 times the through-fall opening of the mesh on a deck, splits between the oversize and undersize streams of the deck, and ii) how near-mesh content of the feed affects the screening performance. In the throughput based sizing method given here, this is accomplished through the introduction of a generalized partition curve and a near-mesh factor. A newly developed efficiency factor is employed in addition to the traditional screen sizing factors.

Jan 1, 1979

By M. J. Reasor, M. DiMatteo, J. M. Antonini, K. Van Dyke, Z. Ye

"The inhalation of silica has been shown to produce a dramatic inflammatory and toxic response within the lungs of humans and laboratory animals. A variety of cellular and biochemical parameters are used to assess the silica-induced lung injury. The purpose of this paper is to introduce the use of luminok:Jependent chemiluminescence as a new method to study inflammation in both phagocytic cells and lung tissue recovered from silicaexposed animals. Chemiluminescence, or the emission of light, accompanies the release of reactive forms of oxygen when phagocytic cells are challenged. In this study, male Fischer 344 rats were intratracheally instilled with either silica (10 mg/100 g bw) or saline vehicle. One day after the instillations. a marked increase in the chemiluminescence was observed in the lung tissue and bronchoalveolar lavage cells recovered from the silica- treated animals when compared with the saline controls. The light reaction was markedly decreased by either superoxide dismutase or N-nitro-Larginine methyl ester hydrochloride. Superoxide dismutase is involved in the enzymatic breakdown of superoxide anion. while N-nitro-L-arginine methyl ester hydrocholoride, a nitric oxide synthase inhibitor, prevents the formation of nitric oxide. When superoxide anion and nitric oxide react. they form the highly oxidizing substance peroxynitrite. This study then implicates peroxynitrite as an agent that may be responsible for some of the oxidant lung injury that is associated with silica exposure. The use of luminol-dependent chemiluminescence may prove valuable as a method to measure the earliest events in the inflammatory process. and may be an adjunct in studying the mechanisms that produce inflammation. - Environ Health Perspect 102(Suppl 10):37-42 (1994) IntroductionResearch on inflammation has not produced a method that links the initial events of the process to the controlling events. Rather, a variety of parameters are measured that are the result of and not the basis of the inflammatory reaction. Parameters such as tissue weight, edema, blood flow, enzyme and protein release, or production of metabolites (prostaglandins, leukotrienes) have been used extensively. A method is needed that could be applied to cells of a particular type, groups of cells of different types, and even tissue, in an attempt to study the kinetics of the inflammation as well as being sensitive enough to monitor the early events of the process . Since inflammation is so complicated, the relationship between the control of the initial events and the oxidation process has never been explained nor studied in any derail."

Dec 1, 1995

By J Hudson

Autogenous (AG) and Semi Autogenous (SAG) grinding mills are the conventional selection for large-scale grinding circuits. It is accepted that these forms of comminution are not the most energy efficient available. This efficiency combined with escalating energy prices, steel prices and the requirement to process larger, lower grade deposits has necessitated that better comminution techniques are found to challenge the dominant position of AG/SAG mills in the grinding circuit. Recent advances in high pressure grinding rolls (HPGR), particularly in terms of roll surface protection have meant that, depending on the application, an economic alternative is available to the large diameter AG/SAG mills. Mining companies now recognise the potential benefits of HPGR and so they need proper assessment in the design of new or upgrade of existing grinding processes. Of course, the answer to the question AG/SAG or HPGR is not straightforward and the impact of the grinding process on the whole metallurgical process needs to be evaluated. Clearly this is a complex decision to make and requires substantial metallurgical knowledge, test work, and objective analysis. The perceived downstream processing benefits will differ between different plants depending on the ore type and processing conditions. The optimal design of the comminution circuit requires that a robust methodology is followed to objectively characterise the ore, size the equipment and determine the downstream processing benefits. The paper gives a brief comparison of the capital and operating costs for both grinding systems, and then outlines the appropriate test work that is required to make an informed decision.

Jan 1, 2006

By Rolando Campos

Until 1970, the Caletones Smelter of CODELCO-CHILE, División El Teniente, operated under the conventional pyrometallurgical process used by most of copper smelters. The annual copper production varied around 165.000 tons. The failure in the commissioning of the "oxygen smelting" technology in Peirce- Smith converters (1970-1972), forced further introduction of transcendental changes in the Caletones smelter operating scheme. Implemented technological innovations were based on wide studies and research works performed by División El Teniente. This paper presents a summary of technological modifications introduced, their impact on production and energetic performances, and short and medium terms improvement plans.

Jan 1, 1993

By Lyden, Joseph P.

THE Picher Mining Field, fig. 1, which lies between Baxter Springs, Kansas, and Commerce, Okla., is the most intensely mineralized and the largest zinc-lead ore producing area in the Tri-State District of Missouri, Kansas, and Oklahoma. It has a vast lateral extent of underground workings that is unequaled for the observation of the geology of zinc-lead ore bodies in sedimentary horizons; and thousands of churn drill holes in the unmined areas supplement the underground observations with useful data for the interpretation of the geology. This paper is confined to the ore deposits of the Picher mining field. The reader is referred to the bibliography for the general geology of the Tri-State district which has been ably covered by many geologists. The writer was co-author of several publications on the Tri-State district.- This paper is necessarily a repetition of parts of those publications but contains a few changes and additions on the deposition of the minerals. The parts of this paper concerning mineralization maps and pipe slump-structures are not covered in the above publications.

Jan 1, 1950