Search Documents

By M. Kalin

"Ecological Engineering and Biological Polishing technology is a decommissioning approach for inactive coal, uranium and base metal operations. To improve acid mine drainage water some fundamental aspects of wetland ecology and sediment microbiology are combined, to provide conditions to allow for biomineralization of the contaminants.This paper summarizes the first records of microbial alkalinity generation in acid mine drainage through the utilisation of the ARUM process. The process requires that the seepage is at pH 4.5 where sulphate reducers utilize sulphate to produce hydrogen sulphide, which in turn precipitates with metals. The pH increase is brought about by alkalinity generating microbes.The ARUM process has been successful in increasing the pH from 2.5 to 7.0. Flow through reactors operated in the laboratory continuously for more than 60 days have removed Ni from 13 mg/L to < 0.01 mg/L. Design parameters are being developed for low flow rates of 5 L/min in a test system receiving seepage from a tailings.1.0 INTRODUCTIONAcid mine drainage associated with mining wastes poses a significant environmental problem. Conventional means to treat acid mine drainage (AMD) use chemical treatment system. Ecological Engineering technology uses natural biological means to curtail and ameliorate AMD during mine operations and at the time of decommissioning. The premise underlying Ecological Engineering technology is that AMD is the result of a natural process enhanced by mining activities. Therefore, in nature, a process providing a natural balance to AMD has to exist, which, when assisted through appropriate means, can counteract the detrimental effects of AMD on the environment. This process is microbial alkalinity generation which is known to occur in wetlands, lake and ocean sediments (Baas Becling et al, 1960)."

Jan 1, 1991

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

Jan 1, 2007

By P. Massi

"Wholly owned by the Coniagas Mining Company, the oldest continuously listed mining company on the Toronto Stock Exchange, St. Andrew Goldfields is located on Hwy. 101 approximately 30 miles east of downtown Timmins, Ontario. Geographically situated on the Porcupine-Destor Fault, the mine and mill in Stock township is positioned in the heart of Northeastern Ontario's goldmining communities.In July 1988, a 600 ft. shaft, hoist, and compressors were already in place when construction started on a 500 T.P.D. capacity C.I.P. mill and crushing plant.By June 15, 1989 the mill was commissioned and attained the design capacity by August of that same year. Since then, changes to the circuit have increased throughput to 900 T.P.D. from two significantly different ore sources.Meeting the Ministry of the Environment's guidelines is an ongoing commitment utilizing the Inca S02 process in line between the tailings pond and secondary polishing pond.INTRODUCTIONExploration on what is now known as St Andrew Goldfields' Stock Township Mine was carried out ln the early l960 1 s by Hollinger Mines Ltd. The property was acquired by Quebec Sturgeon River Mines 1n 1973 and the main shaft was started ill 1979.When St Andrew Goldfields was incorporated 1n 1983, exploration and development commenced to identify the ore body. The company decided 1n 1987 to bring the Stock township property into production after an extensive feasibility study and testwork at Lakefield Research in Toronto. Leslie Engineering was contracted to design, engineer and procure al 1. equipment from the coarse ore bin to the tailings distribution system and backfill plant"

Jan 1, 1992

By K. R. Barnard, K. D. Marte, T. V. Gamarano

"The first commercial scale application of CSIRO’s direct solvent extraction (DSX) technology has been in operation at the Boleo project in Mexico since December, 2015. In this application, DSX is a synergistic solvent extraction system consisting of the extractants LIX 63 and Versatic 10 for recovery of cobalt and zinc from a solution background of manganese, magnesium, and calcium. Key operating parameters such as metal extraction, phase disengagement and extractant stability are summarized and discussed in this paper.INTRODUCTION Commissioning of the Boleo processing plant, located on Mexico’s Baja peninsula, began with the copper circuit starting in late 2014, with first copper cathode production achieved in January, 2015. The cobalt and zinc circuits began commissioning in December, 2015 with first zinc sulphate monohydrate (ZSM) and cobalt cathode production achieved in February and April, 2016 respectively. The Boleo project flow sheet and development has been described in detail in previous publications (Dreisinger, et al. 2005; Dreisinger, Baxter, & Molnar, 2006; Dreisinger, et al. 2008; Dreisinger, et al. 2009) and is summarized schematically in Figure 1. Boleo is a mixed oxide/sulphide Cu-Co-Zn-Mn high clay deposit that is processed in a whole ore, atmospheric, oxidative and reductive, sulphuric acid/seawater leach. Copper is recovered as cathode by conventional solvent extraction and electrowinning. Cobalt and zinc are recovered, from a solution background of manganese, magnesium, and calcium, by CSIRO’s synergistic solvent extraction technology Direct Solvent Extraction (DSX). Cobalt and zinc are bulk stripped from the DSX circuit and then further purified by phosphinic acid solvent extraction to produce zinc sulphate monohydrate granules via spray dried granulation and cobalt cathode rounds via divided cell electrowinning."

Jan 1, 2017

By Alper Turan

The use of aggregate pier foundation systems has become widespread as the engineering practice moves towards cost-effective ground improvement solutions that provide accelerated construction schedules. Increased bearing capacity, effective settlement control and potential for liquefaction mitigation are commonly acknowledged benefits of aggregate piers. This paper studies the mechanisms by which aggregate piers interact with each other and with the surrounding ground when excited by seismic loads. A particular emphasis was placed on the response of a raft foundation supported on a site improved using aggregate piers. Three-dimensional nonlinear finite element analyses were conducted using commercial software package, ABAQUS. Non-linear soil behaviour is modelled using a three-dimensional total stress-based bounding surface plasticity model, which is able to simulate stiffness degradation and damping increase in the soil. The soil stratigraphy considered in this study was a 30 m deep soil deposit that comprised a very stiff base layer and a shallow soft surficial clay layer. Ricker Wavelet time histories with different frequency contents are used as the excitation force in the analyses. Various area replacement ratios (ARR) for aggregate piers are studied for a square plan layout. The results presented in this study are considered to be of interest to researchers and designers in evaluating the seismic ground response of the sites improved using aggregate piers.

By Alper Turan, Hesham El Naggar

"The use of aggregate pier foundation systems has become widespread as the engineering practice moves towards cost-effective ground improvement solutions that provide accelerated construction schedules. Increased bearing capacity, effective settlement control and potential for liquefaction mitigation are commonly acknowledged benefits of aggregate piers. This paper studies the mechanisms by which aggregate piers interact with each other and with the surrounding ground when excited by seismic loads. A particular emphasis was placed on the response of a raft foundation supported on a site improved using aggregate piers. Three-dimensional nonlinear finite element analyses were conducted using commercial software package, ABAQUS. Non-linear soil behaviour is modelled using a three-dimensional total stress-based bounding surface plasticity model, which is able to simulate stiffness degradation and damping increase in the soil. The soil stratigraphy considered in this study was a 30 m deep soil deposit that comprised a very stiff base layer and a shallow soft surficial clay layer. Ricker Wavelet time histories with different frequency contents are used as the excitation force in the analyses. Various area replacement ratios (ARR) for aggregate piers are studied for a square plan layout. The results presented in this study are considered to be of interest to researchers and designers in evaluating the seismic ground response of the sites improved using aggregate piers. INTRODUCTIONThe schedule and cost limitations imposed by the traditional over-excavation and replacement method for the stabilization and settlement control for poor soils resulted are underlying factors for the significant increase in the use of aggregate pier foundation system, particularly in the last two decades. Various well known advantages of aggregate pier systems including increased bearing resistance, settlement reduction, and increased uplift capacity have been studied by various authors. The use of aggregate pier systems for settlement control in soft soil deposits was studied by various researchers including Lawton and Fox (1994), Lawton et al. (1994) and Wissmann et al. (2001). Lien and Fox (2001) studied the behaviour of aggregate pier systems supporting embankments and retaining walls. The stabilization of slopes by means of aggregate piers was studied by Lien and Fox (2001), Wissmann et al. (2002). Thompson et al. (2009) reported on a performance monitoring study of aggregate pier systems supporting MSE walls. The interaction mechanism between the aggregate pier system and the surrounding soil attracted attention of various researchers. Handy and White (2006a) and (2006b) studied the changes that occur less than 2 m from centers of the piers, and further away, respectively. The support mechanism of aggregate pier systems subjected to compressive loading were studied experimentally and numerically by White et al. (2007) and Pham and White (2007), respectively."

Jan 1, 2017

By S. K. Dutta

Enormous amount of iron ore fines is generated, due to partly soft and friable nature, during mining. Coal fines are also produced during their processing. These fines cannot be used directly in ironmaking reactors. Utilization of these fines for extracting metal is of vital concern for resource conservation and pollution control, and therefore, a novel concept of agglomeration by cold-bonding is developed. Composite briquettes/pellets of iron ore fines with coal fines were prepared in the laboratory by cold-bonding technique. Various binders such as lime, Ca(OH)2, slaked lime, dextrin, molasses, fly ash etc were employed either alone or in combination in different proportions for making composite briquettes/pellets. It was possible to obtain dry strength of composite briquettes more than 300 N/briquette in some cases and more than 200 N/briquette in many trials. The combination of fly ash with slaked lime and molasses produced the highest strength, more than 400 N/briquette. Drop strength and shatter index values of composite briquettes/pellets were also measured. In briquettes, best compressive strength (978 N/briquette) is observed by using polyvinyl alcohol (PVA) binder. In pellet, best compressive strength (362 N/pellet) is achieved by PVA; shatter index (0.1%) and dry drop strength (158 numbers) are also good. Compressive strength above 200 N/pellet is obtained by fly ash, slaked lime and molasses combination.

Sep 1, 2012

By Ken MacLeod

A development at 83 Queens Road in Melbourne, Australia required construction of a three level basement. The normal geotechnical constraints of excavating adjacent to an existing relatively new building were challenging enough for the complicated soils profile occurring at the site. An additional significant challenge faced by the designers, was the requirement to excavate underneath the entire footprint of an existing heritage listed building, known locally as the Mansion, in the centre of the site. Maintaining the structural integrity of that building was afforded the highest priority during the 10m excavation. This paper describes geotechnical aspects of the analysis, design and construction of the secant retention system adjacent the new building and support of the Mansion enabling the 10m excavation to proceed without causing damage to the structure. The secant wall comprised hard-soft interlocking piles constructed using CFA methods. CFA piles along the length of the Mansion provided short term support, with the building load being transferred to the piles by large steel beams jacked under the building. Survey results confirmed that movements of the retaining wall and also the load bearing piles were minimal and well within design expectations.

Jan 1, 2006

By D. Ingram

"PRIMARY DUST COLLECTOR A. 42,000 CFM James Howden Fan Z-6 Size 3650 Fan Dia 40"" HP 75It was found that the fan was not large enough to remove the air that was displaced by the trucks dumping. So it was removed and an enclosure was installed to isolate the gyro from the rest of the building.B. FANSJames Howden Fans Model RPM 3500 Series 357 FW HP 10These fans were installed when the first dust system was put into operation. It was found that the high RPM and extreme fan wear caused a major maintenance problem. These fans were replaced with Chicage Blowers Model SWS1 RPM 1180 Dia 36"".DRY CYCLONE COLLECTORS A.,Three four foot rubber lined cyclones. Four six foot rubber lined cyclones.All under flow. Water is controlled manually and gravity flows to a central sump box. From there it flows to the grinding circuit in the Mill.Cyclone under flow product runs between 100 and 200 tons of dust per 24 hours with a screen analysis 30% + 400.The cyclone under flow product is diluted to about 3 to 4%. Solids total gallonage approximately 400.B.,Elbair Wet Scrubber125 HP RPM 56042,000 CFM,Model PX861The Elbair collects the total product from the discharge. Of the Cyclone fans the under flaw goes to the Mill - the Elbair discharges stack goes to atmosphere.The Elbair wet scrubber had to be redesigned in order to keep it in service."

Jan 1, 1976

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

By R. J. MacLeod

"INTRODUCTIONThe removal of water or liquid from slurries and solutions is a procedure generally present in many process industries. This has prompted the development of many mechanical and thermal devices with which, I have no doubt you are al1 familiar.In the mining industry, beneficiation of ores necessitates ' the removal of water or other 1iquid from the concentrate material. The most common method of accomplishing this is by means of thickeners, vacuum filters and rotary dryers, generally all three and in that order;The use of spray drying techniques to obtain the same end has many advantages and these will be outlined here.THE PRINCIPLE OF SPRAY DRYINGA Spray Dryer consists of a cyclone shaped chamber where hot air and atomized concentrate are introduced in the upper section. (Sec figure No. 1). Efficient mixing of these two streams produce dry concentrate and moist spent air, both of which are removed from the base of the chamber.Thermal dewatering involves the product ion of heat and spray drying has no special requirements in this area. Generally a direct fired air heater is used and the products of combustion whether they stem from the use of gas, oil or coal fuel go into the spray dryer along with quench or dilution air which is used to reduce the combustion gases to the desired temperature. This generally lies in the range of 1,000 to 1,600° F. In spite of these relatively high inlet temperatures, the spray drying process eliminates the need for refractory lining or indeed any special heat resistant metals except on the air inlet ducting. Waste heat may also be used even if a significant amount of contamination is present."

Jan 1, 1972

By Steve Hubbard, Brad Marchant, Rolando Cuadra

"Triton Mining Corporation acquired the rights to Mina El Limon in Nicaragua in 1993 by international bid. The bid included the gold operations at Limon and an exploration concession of approximately 4000 km2. Triton assumed control of operations and exploration in May 1994.The Limon mine is located in west-central Nicaragua, approximately 100 kilometers northwest of Managua. The climate is tropical, characterized by a wet season from May through October, and a dry season November through April. Gold at Limon is associated with both banded quartz and silicified breccia veins in Tertiary volcanic rocks, belonging to the lower Coyol Group. Mining is from two open pits and one mechanized underground operation. A second underground mine is currently under development for production during 1997.This paper describes the expansion of the milling facility at El Limon from a nominal capacity of 400 tonnes/day, producing approximately 20,000 ounces of gold annually, to the existing 900 tonne per day mill operation. Engineering of the new mill facility was initiated in September 1994 and construction was completed a year later."

Jan 1, 1997

By H. P. Jacobi

"INTRODUCTIONPine Point Mines, operated by Cominco Ltd., is located approximately 65 miles east of Hay River, N.W.T. on the south shore of Great Slave Lake.The milling operation started in the fall of 1965 with a capacity of 5,000 tpd. An addition was put into operation late in 1968 to bring the nominal capacity up to 8,000 tpd. The present milling rate is 11,000 tpd.With a feed grade of approximately 2.9% Pb and 6.0% Zn the annual concentrate production amounts to roughly 130,000 SDT of lead concentrate and 370,000 SDT of zinc concentrate for a total of 1/2 million tons of product.This tonnage is moved by railroad. Pine Point is served by the Great Slave Lake Division (G.S.L.) of the Canadian National Railways which connects to the Northern Alberta Railway System (N.A.R.) at Roma Junction, at Peace River, Alberta. The system in turn connects to the CNR and the CPR in Edmonton, Alberta. From here the concentrates move inland chiefly to Trail, B.C., with some shipment to other Canadian and U.S. smelters, and to the port facilities of Pacific Coast Terminals at New Westminster, B.C. for offshore export.This paper will focus on the problems associated with the movement of lead and zinc concentrates from Pine Point to port facilities on the west coast."

Jan 1, 1975

By K. V. Konigsmann

"The results of Mr. Klymowsky's research confirm the essential role played by oxidation products in the flotation of base metal sulphides. They invite a discussion on the subject of aeration which I may open by a brief description of the development and current practice of aeration. The first installation of pre-flotation aeration in Canadian milling practice was undertaken during the years 1928 and 29 at the then new Noranda Mill. C.G. McLachlan and his collaborators demonstrated that the flotation differential between chalcopyrite and iron sulphides was enhanced by aeration in soda ash alkaline pulps. The ores treated contained more than 80 per cent sulphides. It was proposed already then that the products of mineral oxidation assisted copper and retarded iron sulphides, at least pyrrhotite flotation. The concentration of thiosulphates was used as a measure of the progress of oxidation. Several papers by C.G. McLachlan elaborate on this subject.The aerator was also used as classifier since it was held that aeration, i.e. controlled oxidation, should go hand in hand with creation of new mineral surfaces. Grinding mills and aerators were placed in closed circuit. Figure 1. This aeration was essential for successful separation at Noranda.Following the application of aeration at Noranda the technique was applied to existing mills in N.W. Quebec. Impressive improvements in concentrate grades and recoveries were obtained. It was observedthat the zinc flotation benefitted from aeration as much as the preceding copper float. In the late forties and fifties the aerator classifier was installed in new mills associated with the Noranda group. A diagrammatic sketch of the Quemont flow-sheet (figure 2) may serve as a typical example."

Jan 1, 1973

By A. Arik

An accurate estimation of mining block grades continues to be a challenging task for ore reserve practitioners. Two of the factors that affect the accuracy of the estimates are the estimation method used and the variability of the mineralization in the deposit. The objectives of the study are twofold: Firstly, to see how different estimation methods perform on a given deposit. Secondly, to determine the impact of particular nature of the mineralization on the results. The comparison of several estimation methods for the prediction accuracy is performed using the conditional simulation results as the basis.

Jan 1, 2000

By M. Javier

Mining, waste is growing problem both physical accumulation and increasing toxic uncertainties it presents in the long run. Its value ?zero? is strictly calculated by economy. This mining model begs the question: What is the value of waste & what does it represent to the mining industry? Waste is widely accepted as a ?by product? generated as a consequences of the mining process. The abundant waste accumulation affects society, as receptor, in many ways and the waste piles of materials has no use and no destiny. In reality, this waste is monument of imperfection of the extractive industries worldwide. Our planet is finite and has strict limitations, which mining has traditionally ignored. It is time to design a new system, in which clearly, waste design must be integrated in whole mining process; it has no room to postpone. This paper presents a concept in waste design by which toxic mining waste not only can be rendered inert but also act as nutrient to help balance the ecosystems. This concept calls for extractive industries to pursue EQUILIBRIUM with nature (Geomimic). Also, this concept offers countless gains and opportunities fro the industry and by converting liabilities into assets; mining engineers become the managers and stewards of nature. Also, waste design offers new solutions for proper and sustainable waste management of the mining industry.

Jan 1, 2011

After nine years of negotiations, the U.N. Conference on the Law of the Sea approved a Law of the Sea Treaty text in April. Israel, Turkey, the United States and Venezuela voted against the text and 17 other nations including Belgium, the Netherlands, Italy, the Soviet Union, the United Kingdom and West Germany abstained. These nations still have the option of joining the treaty when it is opened for signing in December. However, the Reagan Administration has stated that several provisions of the deep seabed mining portion of the text are unacceptable and it seems unlikely that the United States, at least, will change its position. ALUMINUM Reynolds Metals Co. has criticized an Oregon state plan to relax air pollution standards for aluminum plants. The company feels that relaxation of the rules does not go far enough. Reynolds officials say that they have spent about $31 million at their Troutdale plant for state-of-the-art pollution control equipment, and if they are required to make the pollution reductions called for in the 1986 rules, Reynolds would be forced to close the 40-year-old plant.

Jan 1, 1982

By S. Kraemer

Consumption of plastics has been growing in both the U.S. and world markets since the mid-1930s. This growth is due to plastics being used to make new products and as a replacement material for existing products. This paper develops an understanding of the replacement process by looking at the use of plastic, specifically PVC, in the construction pipe industry. History details the growth of the plastics industry and a discussion of the material selection process indicates the advantages and disadvantages of plastic pipe. Analysis shows that the use of plastic, as an alternative material for pipe, is having a significant effect on the cast iron, copper, clay, and steel industries. For the purpose of understanding the replacement process, three example residential systems were examined with a lifecycle cost analysis being performed. PVC was the material of choice in 1988 for all systems. Even though disposal cost was the one area where PVC was not the most cost effective, disposal costs were not sufficient to offset the overall advantage of using PVC on an economic basis. That plastic competes effectively with other materials, in terms of material properties and cost, indicates that further work should be performed to understand the impact plastics have on other material markets.

Jan 1, 1991

By Joseph Coffman

There are 14 operations that supply 97% of the Market Economy Country (MEC) manganese and contain nearly all of its resources. Six mines account for about 70% of the production and 85% of the resources; there are no known resources that are economically close to those that are currently being mined. Costs (January 1989 dollars) of producing manganese concentrates from the operations evaluated are estimated to range from $ 0.96 to $ 1.86 per long ton unit (ltu or 22.4 lb) of contained manganese. Total MEC demonstrated resources evaluated amount to about 1.2 billion tons of in situ ore containing 474 million tons of manganese. Identified resources amount to about 1.8 billion tons of in situ material. Key results of the study indicate the following: 1. The MEC supply of manganese will be from the currently mined resources well into the next century. 2. Centrally Planned Economy Countries (CPEC&apos;s) will be increasingly dependent on MEC manganese ore and concentrate in the future. 3. At the 1976 to 1987 demand increase rate, total MEC resource needed through the year 2000 would be about 282 million tons of in situ material. 4. Transportation and infrastructure support will continue to be major elements of production costs.

Jan 1, 1992

By Raymond B. Ladoo

In order to obtain comprehensive and authentic information on fluorspar mining in the western States , the writer, together with and at the request of representatives of some of the largest fluorspar producers of the Illinois - Kentucky district , spent the month of April , 1922 , in examining all we stem fluorspar deposits ( of which record was available ) believed to be of possible commercial importance .

May 1, 1923