Search Documents

By H. Maleki, G. Tetreault

This study was initiated by the Bureau of Land Management (BLM) to develop guidelines for determining the maximum economic recovery of resources in coal mines. The work was in response to a requirement in the Mineral Leasing Act of 1920 and Federal regulations. The intent was to address the economic rainability of small, irregular reserves in existing longwall mines. In particular, there was a need to determine if room-and-pillar mining using a continuous miner (CM method) was economically sound, or whether unconventional (short or odd-shaped) longwalls could be used to recover small coal reserves economically. Small reserves, called "widgets" are left in longwall mines on one side of the mains, near outcrops and adverse geological conditions, or near any other location where reserve geometry does not lend itself to mining with a rectangular longwall panel. The work included (1) analysis of the geologic, geo-technical, and economic factors that influence the recovery of small coal reserves, (2) analysis of historic changes in supply, demand, and coal prices, (3) development of typical cost models for room-and-pillar and longwall mines, and (4) development of a practical methodology for determining maximum economic recovery. The methodology included an evaluation of the ratio of coal mined during longwall mining to that mined for development (LDR) as well as costs of maintaining coal quality depending on market conditions. The LDR is a good indicator of mine efficiency and overall coal recovery in modem longwall mines and thus is used to evaluate the

Jan 1, 2001

By P. J. Bethell

Background Increasingly complex geological conditions, with the presence of high ash binders in the mining horizon were encountered at the A.C. I. Dugout Mine near Price, Utah. This led to the production of high ash coal from the Dugout Mine during 2003 and 2004. This material had poor marketability and posed operating issues for the utilities burning the coal. Ash levels increased from typical levels in the 9-12% range to between 15 and 25%. etween 15 and 25%. Reviews of the mine plan and expected geological conditions indicated that further periods of high ash production could be expected. Action Plan Detailed sampling of the mine high ash production was carried out. The majority of the coal from the Dugout Mine is trucked to the Savage Coal Terminal (SCT) at Wellington, Utah where it is stored in multiple piles by quality. Coal at the mine is segregated by a CoalScan 2600, on-line analyzer into high ash, low ash and rock chute (waste material). From these piles, the material is crushed prior to shipment to SCT. The samples obtained from the various high ash piles were subjected to detailed sizing and washability analysis. Once this information was obtained, alternative circuit configurations were evaluated to process this material into a salable product. Water supplies in the arid terrain where the plant is located are scarce. This factor played a part in the final circuit design.

Jan 1, 2008

By S. L. Aaroe

"TYRETHANE PRODUCTSTyrethane® is the family brand name which has been adopted by The W. S. Tyler Company of Canada, Limited to identify its polyurethane products. Since we have been manufacturing Woven Wire Cloth for over one hundred years and have been the innovator for most of the product improvements and developments of that industry, it is only natural that our first and primary efforts involve the use of Tyrethane® as a screening medium. The product is ideal for application in the mining industry and other operations where the rate of wear on existing media is exceptionally high.In the event that you have already had some experience with polyurethane it should be poirted cut that there are many grades of the material. The polyurethane used in Tyrethane® Products will be compounded in a variety of chemistries and different heat treatments will be used to develop best mechanical properties to handle specific applications. However Tyrethane® will not be a ""cure all"" but when it is properly applied as a screening medium it will assist by lowering the unit cost for screened materials.Prior to an explanation of the advantages of Tyrethane® let's review the conventional screening media whose applications may be considered as good candidates for replacement by Tyrethane®.1.,Woven Wire Cloth.2.,Perforated metal screens.3.,Rubber faced perforated metal screens.4.,Perforated rubber screens.5.,Cast steel screen segments and weldiments.6.,Profile wire.In most cases a Tyrethane® section is designed for a one for one replacement of the material now being used. It is rarely necessary to modify the screening equipment to enable you to install the Tyrethane® Product although it may be desirable to take some steps to improve the service life of hold down components such as Clamping Strips or Tension Members. Those parts can be encapsulated in polyurethane if necessary.To fabricate the Tyrethane® section we have three basic building blocks. They are: (1) Small molded segments having square or slotted openings, (2) Reinforcing material and (3) the raw liquid polyurethane."

Jan 1, 1976

By R. J. Johnston

"INTRODUCTIONPoint Mines is located about 65 miles east of Hay River on the South Shore of the Great Slave Lake. It is connected to the Northern Alberta Railway System by the Great Slave Lake Division of CN Railways at Roma Junction, Alberta.The operation started in the fall of 1965 with a capacity of 5000 t.p.d. An addition was put into operation late in 1968 to bring the capacity up to 8000 t.p.d. The present milling rate is 11,000 t.p.d.The location of Pine Point Mines is such that long end cold winters are to be expected end temperatures of lower than -200F are encountered from late October to late March, with extended periods of -300F being common in January and February.It was recognized by Cominco engineers during the initial design period that since freezing would be encountered with open pit ore somewhere in the crushing circuit, the problem was to reduce it as much as possible. Other mines, working under similar conditions, found that the fine ore bins feeding the grinding circuit were the main problem area. The decision was reached, therefore, to have heated fine ore bins and to make sure thst the ore was sufficiently warm to prevent freezing.CRUSHING PLANT FLOWSHEETThe crushing plant has a standard open flow circuit (flowsheet). Ore from the stockpile is loaded into R-50 Euclid trucks by Caterpillar 992 Front End Loader with 11 cu. yd. bucket and dumped into a 42 x 65 C.A.C. Superior Crusher driven by a 300 HP motor. The crusher is set at a nominal 5 inches. The ore falls through into a 100-ton surge bin. There are high level and low level nuclear gauges to allow the primary operator to optimize for optimum orientation."

Jan 1, 1972

By H. C. Verakis, M. L. Harris, M. J. Sapko, K. L. Cashdollar

In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. The National Institute for Occupational Safety and Health (NIOSH) has developed a hand-held instrument that uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture. This instrument is called the Coal Dust Explosibility Meter (CDEM). In this study, NIOSH personnel accompanied Mine Safety and Health Administration (MSHA) inspectors on their routine band surveys in five and three underground coal mines in MSHA District 2 (PA) and District 11 (AL), respectively. While underground, NIOSH personnel and MSHA inspectors used the CDEM to assess the explosibilities of the dust samples. The values of percent incombustible content (% IC) determined by the CDEM agreed well with those obtained later by low temperature ashing (LTA) in both MSHA and NIOSH laboratories. Further, the meter identified some samples as potentially explosible that LTA analysis had found to possess sufficient rock dust for inerting. The CDEM provides more information on the hazards in the mine. Rapid identification of areas with explosible dust mixtures using the CDEM allows for immediate intervention rather than a wait of several weeks for laboratory analysis.

By Wei Zheng

A pulverized coal fired power plant is being built in Osceola, Arkansas, along the Mississippi River. The subsurface soil conditions consist of a certain amount of very soft clayey silt and clay underlain with a medium dense sand layer and a dense sand layer. The site has been raised four to five feet with fill material consisting of sand and gravel. Consolidation settlement due to the fill is expected to cause negative shaft resistance (downdrag) on the pile foundations. The site is located in a high seismic hazard area - the New Madrid Seismic Zone (NMSZ). The liquefaction analyses indicated that there is a high liquefaction potential in the medium dense sand layer. Load tests are needed to determine the shaft resistance and the end bearing of each soil layer for design purpose. Two types of pile foundations ? augered pressure grouted displacement pile (APGD) and partial augered pressure grouted displacement pile (P-APGD) were considered for this project. Ten pile load tests, including five compression tests and five tension tests, were performed for three different areas. Strain gauges were installed for the compression tests. The APGD and P-APGD piles were installed side by side for comparison. In addition, three additional dynamic tests were performed to supplement the information from the static load tests. Load deflection curves for the compression tests were predicted, and the failure loads were interpreted using four different methods. The shaft resistance and the end bearing were determined from the strain gauge data and were used to back calculate the ultimate capacity. The back-calculated capacities are in good agreement with the predicted failure loads; they were further verified with the tension load test results.

Jan 1, 2007

By K. Mikulash

"Agnico-Eagle Mines Limited is located at Joutel in North-Western Québec. The mine is about four miles north-west from the town on the left bank of the Harricana River. The present mining is 1,800 feet deep with an extensive geological development below this level.HISTORY The development of the ore body started sometimes in 1967 and then the operation ceased in 1969 and again reopened in 1973 due to higher prices of gold. During these periods of active development, a considerable metallurgical research has been done by different laboratories and research and design companies.The original capacities of the Mill differed as much as 30%. So did the concept of the ore treatment. The original design of the mill was for 200 TPD of ore with straight cyanidation. The problems with low gold extraction, high reagent consumption and poor filtration resulted in a decrease of the expected mill output to an initial 550 TPD with gold recoveries in the order of 40 to 60%.Although the studies and research work done on the ore varied, all of them had a common conclusion: a very fine grind is needed to expose gold. The mining method (sub-level blast hole mining) now provides the ore that differs from that on which the metallurgical test work was conducted and the original capacity calculations had been done.These variations in the concept consequently led to the conclusion that the size of gold is a determining factor for the process.Kilborn Engineering provided the original design with the Leslie Eng¬ineering completing the design. The metallurgical test work has been done by the Department of Energy, Mines & Resources, Lakefield Research of Canada, Kilborn Engineering and Sidam Incorporated.The new flotation section with secondary grinding has been designed and put into operation by the company in December 1975 with the results yet to be evaluated."

Jan 1, 1976

By J. D. Patsey, G. T. Lineberry

Introduction A computer program was developed for analyzing drum-type hoists before modifying an existing system or designing a new one. Its use permits the preliminary evaluation of a system before seeking technical assistance from mine hoist designers and manufacturers. The user-friendly program accepts a variety of data and analyzes hoisting systems for any balance state. The program can be used to calculate skip capacity to yield a desired production rate, solve for drum face width, select a permissible wire rope, estimate total horsepower of the hoist plant, and estimate annual power cost. Whether required for a large mining complex or for a relatively small operation, a hoisting system must be carefully designed to ensure the efficient, reliable, and safe flow of material. Because shaft sinking and hoist installation can total between 2.5% and 3% of the cost of opening a deep mine, proper hoist selection is critical. Today's mining engineer has at his disposal the most powerful design and analytical aid ever, the microcomputer. There is, unfortunately, limited software for the study of hoisting systems, unlike that for other materials handling equipment (Manula and Albert, 1980; Prelaz et al., 1964; Bucklen, 1969; Thompson, 1985). HOIST reduces a time-consuming set of calculations to a concise package of interrelated subprograms. A literature review revealed no common-user programs to analyze hoisting systems, although at least four major hoist designers/manufacturers/installers have their own in-house programs. To provide a tool with which the mining engineer could preliminarily analyze a materials hoisting system or could check the calculations of a hoist contractor, a computer program was developed. HOIST was written in BASIC for the IBM-PC for ease of program adaptation and to encourage field use on compatible systems. Details of program development are omitted, since the basic principles of hoisting analyses are relatively straightforward, simple, and readily accepted (Harmon, 1973; Nordberg, n.d.; Adler, 1957). Program features, intended usage, and benefits of the computerized solution are emphasized over theory development and mathematical rigor. Background The mine hoist system that is selected and installed at a mine is the "lifeline" of that mine, with installations lasting 20 years or more. Thorough study is warranted to ensure that productivity demands are met at a minimum cost per ton. The increased cost of a large, powerful, high-speed hoist must be offset by increased production to justify its selection. To optimize this tradeoff, an extensive hoisting analysis should be performed. The analyses to properly size the skip (or cage), the drum, and the hoist drive are conducive to computerization, permitting rapid evaluation of changeable operating and design parameters, such as velocity, acceleration, state of balance, and productivity demand. The program is particularly useful in conducting sensitivity trials, such as investigation into the effect of change of productivity on skip capacity and on horsepower of the hoist drive. HOIST is currently limited to the study of drum-type hoists with cylindrical drum(s). However, only minor changes to the program would permit analysis of friction hoists and conical drum configurations. Model development and testing The program is based on accepted equations and physical relationships. Examples of manual calculations formed the basis for decision points and program branching. Data is input in the order that it would be needed if the problems were solved manually. The choices are arranged likewise. HOIST was developed in sections, with manual solutions performed to check program logic. The testing became more rigorous as sections were completed. Output from one section becomes input for following sections, as appropriate. The simplified flow diagram of HOIST is given in Fig. 1.

Jan 2, 1987

By C. B. Webber, W. A. Grell

"Sherritt Gordon's Ruttan Mine is a copper-zinc operation located approximately 600 miles north-west of Winnipeg. Open pit mining began in 1973 at 10,000 Tpd., with a change over to underground mining in 1981 producing 7,500 Tpd. Ore is crushed to -3/4"" followed by rod and ball mill grinding (two ball mills in series), differential copper-zinc flotation, and dewatering. The copper and zinc concentrates are trucked 75 miles to Lynn Lake, where they are shipped by rail to the HBM&S smelter at Flin Flon.This paper describes a method used to predict the effect of grind particle size on metallurgical performance, as well as details on the copper and zinc metallurgical performance due to fine grinding in actual plant operation.Initial statistical studies on historical data (including ore source, head gr3de, grind, etc.) indicated that copper and zinc recoveries increased with fineness of grind, in the range of 50 to 65% -200 mesh.In order to extrapolate beyond 65% -200 mesh, and to develop expected nonlinear relations between grind, Cu concentrate grade, and recovery, the assays of screen fractions of copper concentrate and tailing were used to determin8 the relation between net smelter return (a function of grade and recovery) and grinding cost. The optimum economic grind would be that grind at which the net smelter return less grinding cost reached a maximum."

Jan 1, 1982

By T. Yegulalp, M. Castaldi

As global energy demands increase, there will be a critical need to employ fuels that have minimal environmental impacts. While hydrogen is considered the ultimate fuel for that purpose, hydrocarbon based fuels will be in use for a considerable time and will probably be the first major source of hydrogen for next generation power systems. The best fuel for this transition will be natural gas because of the high hydrogen to carbon ratio. Natural gas hydrates have the potential to meet the global energy needs for the foreseeable future. The amount of energy stored in natural gas hydrates is significantly more than that of all the other fossil fuels combined. However, most proposed techniques for recovering the natural gas from the hydrate require too much energy input, raise safety concerns or can only recover a fraction of the gas. This paper discusses the technical feasibility of a novel method of gas production in hydrate reservoirs. The method is an in-situ process that creates a point heat source in the hydrate formation. This method not only significantly reduces the energy input, but also has the potential to sequester as much or more CO2 than would be produced from combustion of the natural gas produced, thus making this in-situ methane production technique virtually carbon neutral. Simulations using FEMLAB™ show that the method offers an energy efficient and environmentally friendly way to produce natural gas from hydrate reservoirs. Preliminary results indicate that it is possible to have an energy efficiency of nearly 90% for land based reservoirs for hydrate loadings of 20%. The simulation results also suggest that alternatives to a point source can be employed which may improve the process efficiency.

Jan 1, 2007

By C. D. Elifrits, N. B. Aughenbaugh

Introduction Federal and state laws enacted to regulate coal mining and the accompanying public concern about the adverse effects that mining might have on land use have focused much attention on the subsidence of the land surfaces over underground mines. Some questions asked are: • Will abandoned mines subside in the future even though they have exhibited no surface adjustment to date? • If so, when will subsidence take place? • Can a specific surface area be affected by subsidence more than once? • What surface form will the subsidence feature take? • Is there any way to predict when subsidence will occur and end? An attempt is made here to address these questions insofar as it is possible with available data and experience of evaluation of subcritical extraction conditions. Mining that results in subsidence features can be classified as supercritical, subcritical, and critical with respect to the minimum span lengths of the worked-out rooms (Fig. 1). A complete basin will not develop fully immediately over subcritical conditions because the span lengths of the entries are less than the critical dimension (Wardell, 1983). Passageways, entries, and room-and-pillar panels are all included in the subcritical category. Because of the short span lengths, subcritical mining conditions tend to be stable over the life of the mine unless adverse geologic conditions exist (Gray et al., 1974; Dunrud, 1976). Various roof control and support procedures are employed to maintain entry stability during mining. Little information exists concerning the time factor of subsidence over areas of subcritical extraction. Data that have been collected relate to longwall mines, whereby the cavity sizes are designed large enough to induce caving behind the working faces so that complete subsidence at the surface occurs within a short period of time. The UK's National Coal Board (1975) has reduced the enormous amount of data it has collected to empirical correlations and has published these correlations in its Subsidence Engineers Handbook. The handbook states that "None of the foregoing remarks applies to pillar and stall working," with respect to the section discussing the time factor of subsidence caused by longwall mining (National Coal Board, 1975, p. 40). To understand and evaluate how time relates to subsidence above room-and-pillar mines, one must first recognize how mine cavities deteriorate and fail. The propagation of failure to the surface must then be studied, and, finally, the failures that are manifest at the surface in the form of depressions accompanied by both compressional and tensional movements must be investigated. Failure of mine cavities Any cavity beneath the earth's surface represents a condition of nonequilibrium and tends to close with time. Failure of cavities in a subcritical mine can be classified as failure of the roof, failure of the floor, failure of the supports (pillars, cribs), and elastic rebound of the rock. One mode of failure may dominate, but generally combinations of the four will occur. Also, initial instability of geologic materials and structural features and in situ stress may be unknown factors that can contribute to cavity failure. Roof failure is the most obvious opening stability problem in most operating mines. The bridging capabilities of the roof rock are dependent on the rock's material strength, geologic discontinuities, and reaction to humidity changes in the air of the mine. This type of failure may vary in magnitude from gradual flaking to massive roof falls. Mine floor instability can be manifest in the form of a general heave over a broad area or of individual pillar punching. The weaker and thicker the immediate floor material, the more prone a mine is to experience floor problems. Water seeping into an area can soften the underclay, reduce its bearing capacity, and precipitate failure of support for the overburden.

Jan 8, 1986

By N. Ahmed

The collection of hydrophobic particles in the froth phase in flotation has been studied. A continuous flotation cell was developed, in which the froth phase could be isolated from the pulp zone. Hematite particles, d80 = 87 µm, were floated in the pulp, using a conventional oleate collector, while glass spheres of similar diameter, d80 = 82 µm, were introduced in wash water added to the froth. Four samples of glass spheres, with contact angles between 0 and 82 degrees, were used. The results indicate that the efficiency of collection of the hydrophobic particles in the froth can be very high. The process is strongly influenced by the hydrophobicity of the particles and the surface area available for attachment in the froth. Recommendations for the flotation of particles in the froth phase are made, especially regarding the desirable hydrophobicity as reflected in the contact angle, the froth depth, the solids concentration in the feed to the froth, the air rate and the wash water rate.

Jan 1, 2001

By L. Betteridge, A. Marks

"An OK 300 cu. ft. Skim - Air cell was installed at the HBM&S concentrator in Flin Flon in 1987. Since that time, 3 additional OK Skim - Air cells have been installed in HBM&S concentrators. The cell treats a coarse 70% solids slurry with a residence time of 2.5 minutes. The product from the cell (a unit cell type application) is a final grade copper concentrate with high precious metal values. Since its installation, the cell has improved gold recovery by 10 - 15%. Process variables such as circulating load, pH, froth depth, feed size, and reagent additions all have an effect on the operation of the cell. Maintenance on the cell has been minimal. Initial operating problems involving level control have been significantly reduced and operations are now relatively trouble free. Although very successful at Flin Flon, site specific operating circumstances will determine the suitability of this cell. INTRODUCTIONHudson Bay Mining and Smelting operates four concentrators in Northern Manitoba. Three treat copper-zinc ores, the fourth mills a copper-nickel ore. The Flin Flan concentrator operates two circuits in parallel which treat copper and zinc ores from the Trout Lake and Callinan mines. Both circuits in the Flin Flan mill have Skim-Air cells integrated into the grinding circuits.The Trout Lake cell was installed first and had a payback period of a few months. Required modifications to the cell were made to enhance its performance. These included changing the discharge valve size, tuning the level controller, and installing an insert into the rubber valve sleeve to increase its wear life. The payback period on the Callinan cell was significantly reduced because these modifications were completed prior to its installation.The cells produce a final grade copper concentrate and since their installation gold and silver recoveries to the final copper concentrate have increased significantly. Operating parameters such as coarseness of cell feed dictate the metal recoveries and froth depth determines the selectivity of the cell and therefore the grade of the concentrate.The Skim-Air cell can be suitable in applications where a final product is generated. However, when a bulk concentrate, which requires further separation, is produced, the coarseness of the product may not make it amenable to conventional flotation.The Flin Flan mills Skim-Air cells have worked exceptionally well with little maintenance required."

Jan 1, 1991

By H. Arima, T. Fujita, W. Yen

The copper catalyzed gold oxidation and reduction mechanisms in ammonium thiosulfate solution were investigated by Eh-pH diagram based on the optimum reagent combination for 60 mass% -75 µm silicate ore at 16g/t Au with the maximum gold extraction of 92% and the minimum ammonium thiosulfate consumption of 23 kg/t-ore for 24 hour’s leaching at ambient temperature. The gold recovery by cementation was nearly 100% by Zn and Al powders at Metal/Au mass ratio of 30, and around 95% by Cu powder at Cu/Au+ mass ratio of 50. In order to oxidize the gold efficiently with the less thiosulfate consumption, the stable region of [Cu(NH3)4]2+ should be as wide as possible in the region, where [Cu(S2O3)2]3- was more stable than [Cu(NH3)2]+. In order to reduce gold from the pregnant solution with the less metal powder’s (Zn, Cu, Al) consumption, the stable region of [Cu(S2O3)2]3- should be wider than [Cu(NH3)2]+ on copper precipitation. Zinc powder may recover gold more efficiently than copper powder with the similar trend on the effect of ammonia, copper and thiosulfate. However, the large amount of copper will be co-precipitated along with gold since the stability of zinc ammine and thiosulfate complexes are higher than that of copper’s. Aluminium may reduce gold efficiently at higher thiosulfate concentration and pH. These results were confirmed and compared with the optimum reagent combination for finer grind sample at 100 mass% -75 µm, which is the optimum ore size for the standard cyanidation at 1.0 g/ l NaCN to obtain about 95% gold extraction. The optimum reagent combination was concluded as 0.5 mol/l NH4OH, 0.0001 mol/l CuSO4*5H2O and 0.05 mol/l (NH4)2S2O3 with the result of 94% gold extraction and 3kg/t-ore of ammonium thiosulfate consumption. Gold and copper stabilities were well agreed with the result of coarser grind ore thermodynamically. The lower reagent combination will reduce gold oxidation power, but significantly minimize the reagent consumption. From this pregnant solution, nearly 100% of gold was successfully recovered by zinc precipitation at Zn/Au+ mass ratio of 30. Aluminium and copper precipitations resulted in less than 40% of gold recovery at Metal/Gold mass ratio of 30. The reagent consumption cost on this lower reagent combination followed by zinc precipitation was $1.6/t-ore, while the cyanidation was $3.1/t-ore. Thiosulfate oxidation mechanism indicated the similarity to Belousov-Zhabotinsky reaction.

Jan 1, 2002

By D. Nutakor

Rock joint stiffness is not only a poorly known parameter, but also has no established laboratory measurement procedure. This paper presents methods used to determine the normal and shear stiffnesses of healed joints filled with vapor-altered minerals obtained from the Yucca Mountain site in Nevada. Results show that these joints behave linearly up to 85% of their loading history and are stiff with strengths very close to the strength of the intact rock. Factors that might have contributed to the linear behavior of these joints are discussed and areas requiring further investigation are provided. Joint normal stiffness ranges from 7.16 to 64.77 GPa/mm with an average value of 26.93 GPa/mm, while joint shear stiffness averages 11.41 GPa/mm and ranges from 3.09 to 28.41 GPa/mm. Young?s modulus of the vapor-altered joint infilling was calculated from the stiffness of the healed joint. Young?s modulus of the vapor-altered joint filling material averages 7.89 GPa and ranges from 2.15 to 19.43 GPa. Given the pervasive presence of such altered rock, usually in the form of sub-spheroidal 3-D pockets, this property should be of value in any numerical modeling attempting to describe the mechanical behavior of these tuff formations at the level of detail where inclusions might be a factor.

Jan 1, 2008

By S. K. Oraee

Managers always look for systems with minimum hazards. The hazards create problems for performance of projects. The largest and most important hazards of working underground mine can be related to health, safety and environmental, because if one of these sectors be in hazard, maybe lead to close mine. Failure mode and effects analysis (FMEA) is a widely used quality improvement tool to identify the potential failure modes for measuring reliability of a product or a process. FMEA is performed by developing a risk priority number (RPN), which is the product of severity, occurrence, and detection ratings. On the other hand, with regard to uncertainty in the decision-making, fuzzy theory will be able to model this uncertainty. Fuzzy FMEA provides a tool that can work in a better way with vague concepts and without sufficient information than conventional FMEA. This article by using Fuzzy FMEA and based on HSE criteria evaluate hazards of Parvade No. 1 Mine in Tabas Coal Mine. The results demonstrate the most hazardous parameter is rock burst in this mine.

Jan 1, 2011

By A. Noble

The design of separation circuits can be a complex, labor-intensive and costly process. While the engineer?s experience along with extensive data sets and simulation are crucial tools for determining the final solution, a more fundamental approach is suitable to compare preliminary options and reduce the number of potential alternatives. In light of this need, the authors have developed the Circuit Analysis Reduction Tool (CART?). This software package relies on the fundamental principles of linear circuit analysis; however, the solution methodology has been streamlined to automatically incorporate stream splitting and unique separation performance for each unit. The resulting tool allows preliminary analysis of circuit designs without the need of detailed feed characterization. In addition to the basic analytical approach, this paper supports the veracity of the methodology with several simulated examples for various separation models.

Feb 27, 2013

By R. J. Fantel

The Bureau of Mines investigated the resources, costs, capacities, market relationships, and short- and long-run supply of phosphate rock and phosphoric acid. The 206 mines and deposits evaluated in 30 market economy countries contain an estimated 35.1 billion mt of recoverable phosphate rock (demonstrated resource level). U.S. resources are sufficient to satisfy the domestic and export markets for phosphate products well beyond the year 2000. Because of resource depletion at current producers, however, new properties (with higher cost levels) need to be developed if U.S. production levels are to be maintained. Existing worldwide capacity can satisfy expected demand through the early 1990's. Expansion at existing mines or low demand growth could mean that no new property development will be needed before the late 1990's. Worldwide, almost $8 billion could be required for development of new phosphate rock properties between now and the year 2000, given 3-pct annual growth in demand. Most properties that could develop in the 1990's would require price increases of 20 to 50 pct to break even. To earn a 15-pct rate of return on investment, prices must rise to nearly double the present level of $24 to $29 per metric ton.

Jan 1, 1988

By WILLIAM F. McMURRAY, James O. Lewis

The Bureau of Mines is investigating the technology of petroleum and its products, the investigation including well-drilling methods and the transportation, treatment, and utilization of petroleum and of natural gas, with especial reference to the prevention of waste and to increased efficiencyin the development of oil and gas resources in land belonging to or controlled by the Government. During. the winter of 1912-13 the enormous waste of the gas encountered while drilling for oil in the Cushing field, Oklahoma, called forth protests from various sources, and appeal was made to the President of the United States and to the Secretary of the Interior in behalf of the landowner and of the public in general. The facts were wanted regarding the amount of waste and the technical conditions that were responsible for practices causing it. An investigation was ordered and conducted under the direct supervision of the late J. A. Holmes, the first Director of the Bureau of Mines. R. S.Blatchley was sent to investigate the amount of waste going on in the Mid-Continent flelds.s In the latter part of March, 1913, J. A. Pollard and A. G. Heggem were sent to Oklahoma to study well-drilling methods with reference to the waste of gas from wells on Indian lands and to suggest means of preventing the waste of natural gas on such lands. Pollard and Heggem decided that the mud-laden fluid process, which had been used successfully for some years in Texas, Louisiana, and California was the method that would meet the situation most efficiently and economically. The method was accordingly demonstrated in Oklahoma. In 1914 Congress provided for the employment of six oil and gas inspectors to supervise oil and gas mining operations on lands of the Five Civilized Tribes in Oklahoma and to conduct investigations with a view to the prevention of waste. Positions under this appropriation have been held by William F. McMurray, James O. Lewis, Harry D. Aggers, Ralph R. "Weed,George W. McPherson, James C. Fowler, Louis W. Courtney, and Carl H. Beal, the technical work of these men being directed "byW. A. Williams, chief of the petroleum division, Bureau of Mines. After careful and impartial investigation of conditions in Oklahoma, these men also decided that the mud-laden fluid process was the one best adapted to prevent further wastes. In 1915 laws were passed by the State of Oklahoma that provide for the conservation of natural gas and oil, authority being given to the corporation commission to make rules and regulations and to employ agents to enforce them. After hearings and investigations, the corporation commission reached substantially the same conclusions as the Federal agents regarding the importance of the wastes and the best methods of conserving the gas. Technical Papers 66a and 68b were published by the Bureau of Mines in December, 1913, and January, 1914, respectively. Technical Paper 66 deals with the mud-laden fluid process in general and No. 68 with its application in Oklahoma. The interest aroused by these publications has been so widespread that within two years the first editions have been practically exhausted. Rather than reprint these publications, it has been considered advisable to replace them with the present report, which includes the results of more recent investigations. The methods of using the mud-laden fluid are an outgrowth of the rotary drilling system, which was developed in Texas and later employed in Louisiana and California. Some of the principles of the use of mud fluid had been observed and used to a limited extent for a long time in cable-tool drilling. So far as known it was first used successfully with a circulator and cable tools in the Coalinga field, California, in 1906,Harry D. Aggers, one of the contributors to this paper, working on the well. The part of the Bureau of Mines has been to call attention to its merits and to demonstrate its practical use in fields like those of the Mid-Continent.

Jan 1, 1916

By J. W. Thompson

A contract stipUlating for the delivery of quantities of phosphate rock" f. o. b. mines," and stipUlating that" while this contract is in form an absolute sale for a fixed quantity in each year, it is mutually understood and agreed that the purchase is for the buyer's consumption and not for a sale; the buyer agreeing to give to seller the refusal of any surplus over and above the actual consumption. Buyer is at liberty to increase or diminish the quantity called for in any year, to the extent of not exceeding 10 per cent; provided that the quantity to be taken shall not be less than buyer's consumption; provided further that notice of such increased or diminished demand be given seller 12 months in advance of such change," is to be construed as a contract for the sale of stated quantities of rock, deliverable in approximately equal quantities during each year for the specified series of years, subject only to be increased or diminished after specified notice in any year, where the amount taken would not be les<; than the buyer's consumption, not exceeding 10 per cent, and the contract indicating that the rock was intended by both parties for consumption in the fertilizer plant of the buyer. but the quantity to be taken was not limited by the necessities of' the plant.

Jan 1, 1916