Search Documents

By Lawrence Addicks

(San Francisco Meeting, September, 1915) THROUGH the courtesy of Dr. James Douglas I am permitted to give, a summary of some of the results obtained in leaching slimes tailings in a series of experiments conducted under my direction at Douglas, Ariz.. during the past year. While the test run for which the data are given deals with a particular case, much of the work is general in its application and may therefore be of interest. This work was done upon the ores of the Burro Mountain Copper Co. A description of the geology of the district will be-found in the paper by R. E. Somers published in the May, 1915, Bulletin of the Institute. The mineral is pyrite and chalcocite very finely disseminated throughout the gangue and a characteristic of all the ores is the large amount of alumina present. A representative analysis of the particular ore under consideration would be about as follows: Cu, per cent 2.35 S, percent 3.0 Ag, ounces per ton 0.05 CaO, per cent 0.5 Au None K202, per cent 4.0 Fe, per cent 1.5 SiO2, per cent 70.0 A120,, per cent 13.0 The leaching of the ore direct was early dismissed from consideration for the following reasons: 1. The ore would have to be quite finely crushed to liberate the mineral for leaching; concentrating after crushing would cost but a few cents a ton; and a higher total recovery would result from leaching tailings rather than ore. 2. Rough concentration would yield a suitable material for roasting to make sulphur dioxide or sulphuric acid in connection with the leaching scheme. 3. Such a program put the question of cost vs. recovery on a basis where flotation and discarding of tailings were directly comparable.

Jan 8, 1915

By Gustav Hawlitschek, Henrique Kahn, Carina Ulsen, Renato Contessotto

"The problems related to waste dumping increased with the growth and development of large cities. In the U.K., more than 50% of landfill waste comes from construction use and the U.S. alone produces around 200 to 300 million tons of CDW annually. The exhaustion of natural sand deposits close to large urban centres stimulates the recycling of construction and demolition waste for the production of recycled aggregates as a construction material. This paper presents a flowchart for the production of recycled sand with low porosity and regular shape by the selective removal of the cement paste attached to recycled aggregates. The products characterization was carried out by the determination of the particle size and shape distribution, chemical and mineralogical composition, heavy liquid mineral separation and quantification of all present phases using a scanning electron microscopy with automated image analysis (SEM-MLA). The comminution of CDW by vertical shaft impact crusher made possible the production of a lower porosity recycled sand. The heavy liquid mineral separation showed that the proportion of low porous phases (d>2.5 g/cm3) is very high, exceeding 70% of the weight, encouraging further mineral processing separation to obtain a fine recycled aggregate with less cement paste content. The mineralogical characterization by XRD and SEM indicates that the main phases are tectosilicates, phyllosilicates and calcite which one can be attributed to both calcareous aggregate and cement paste. The precise quantification of cement paste and calcite/dolomite alone is just possible by automated image analysis. The characterization results demonstrated that proportion of phases with no cement paste attached increases progressively in denser products. The results of heavy liquid separations and image analysis are comparable and automated image analysis can be used for the characterization of phase content and their main associations."

Jan 1, 2014

By Akira Usui

Occurrence of hydrogenetic ferromanganese crusts has been well documented over inactive seamounts in the central and southern Pacific Ocean. It has been thus believed that the hydrogenetic crusts develop preferentially at water depths between about 800 to 2500 meters. In fact, according to the Manganese Crust Database (F. Manheim, 1988), only two occurrences are known at water depths below 5000 m out of 819 occurrences cited in the database. Unexpectedly, we found typical hydrogenetic ferromanganese crusts from deep-sea floors; 1) outcropping old volcanic basement over the Philippine Sea Plate (abandoned spreading centers and subducting old oceanic crusts) and 2) one from the slope of an abyssal hill in the Central Pacific Basin (Cretaceous deep-sea basin) at water depths ranging between 5200 to 6100 meters. We report their occurrences with submersible observations from Shinkai 6K, physical parameters (such as thickness of crusts about 2-4 cm in maximum), chemical composition, petrology of substrate, and results of Be-10 dating for some samples in comparison with typical Co-rich manganese crusts from the Central Pacific seamounts. The preliminary chemical and mineralogical analyses reveal that they are of typical hydrogenetic origin, and typical of iron-manganese oxide mineral, vernadite, slow and probably continuous growth, and lower content of Co than the Central Pacific seamount crusts. The occurrences and nature of the crusts indicate that deep-sea floors are also optimal for the growth of hydrogenetic crust even at 5000 m water depth or deeper, only if oxygenated deep waters are supplied and the sea-floor morphology keeps stable enough for significant geological time period. Additional details of chemical analyses will be prepared by November and to be shown in the conference.

Jan 1, 2001

By F. Logsch, H. Pempel, J. Markowski, P. Ay

"Due to the European Directive 2000/53/EC on end-of-life-vehicles, from 2015 on more than 95% of car materials have to be recycled. In order to recycle the materials back into the economic cycle, it is necessary to produce products with high quality and purity.Plastic components in cars, which are coated with metals by vapour deposition or electroplating, have a wide circulation (e.g., as cladding panel or trim strip for interiors and exteriors). In the end-of-lifevehicle recycling process, these plastic-metal composites are not considered in usual technologies (car shredder) and are not separated from Automotive Shredder Residue. These parts can be separated by optical or HF-detection sorting and then introduced to a specific treatment.Experiments with a specially developed bioleaching configuration showed that the thin coatings, which consist mainly of copper, nickel and chromium, can be removed efficiently from the polymer base materials by a bioleaching solution with Acidothiobacillus ferrooxidans as a leaching agent. The solution used was produced in special fermenters with a 9K-nutrient salt media. During the bioleaching process at 35°C maximum temperature, most of the copper is dissolved and the other metals accumulate as metal sludge. The bacterial cultures based on A. ferrooxidans are robust and resilient.After a 48-hour bioleaching period while the composites were stirred regularly with ventilation, the plastic particles were completely free from metallic coatings. The metal components are separated for further use: undissolved components (mainly Ni and Cr) are separated by decantation of the solution; dissolved copper recovey is carried out by cementation of copper. The cementated solid contains ~98% Cu, along with small amounts of other metals.With the bioleaching process, good separation and re-utilization of the metallic coatings is possible. The cleaned plastic parts were prepared by compounding for new applications with injectionmoulding."

Jan 1, 2016

By K. S. Kumar

FLS miljø, Inc. markets, designs and supplies particulate collection devices for dusts, fumes, and mists; In this paper, the application of both wet and dry electrostatic precipitators (ESPs) in smelting, and roasting plants is discussed.

Jan 1, 1998

By P. E. Auger, J. E. Gill

"The zinc deposits to be described are in Lemieux township a few miles south of the Tabletop mountains, in the central part of Gaspe peninsula, Quebec. Although they have not been worked, they constitute a potential source of zinc and lead and structurally are of considerable interest.GENERAL CHARACTER OF THE OCCURRENCEThe deposits are in sharp-walled quartz-carbonate veins and breccia zones carrying locally, and in varying amounts, sphalerite, galena, pyrite, marcasite, chalcopyrite, and specularite. Those so far investigated strike generally north-south, have steep dips, and cut through sediments of Lower Devonian age, mostly calcareous argillites or siltstones. Wall-rock alteration is negligible.BROADER STRUCTURAL FEATURESThe principal known occurrences are in the south-central part of a dome structure measuring 6 by 5 miles. The argillaceous sediments are overlain, on the flanks of the dome, by sandstones and lavas. These have been stripped from the central part of the dome, revealing the veins in the argillites beneath. The veins formed after the volcanics, but the fractures and breccia zones in which the deposits formed are confined mainly to the argillite series, presumably because of the greater strength of the lavas.The argillite series is cut by dykes, sills, and small stocks of diorite and acidic 'porphyries' that are older than the veins.THE FEDERAL HILL AREAThe distribution of known veins is shown in Fig. 1. The characteristic features of the veins are well illustrated by the Federal Hill area shown in Figs. 2, 3, and 4, and described below."

Jan 1, 1954

"For many years it has been known that large bodies of iron ore existed in Iron and Washington counties in Utah. The ore is chiefly hematite—both hard and soft—though some magnetite is found. No definite and complete estimate of the iron ore reserves of the state have been made. The U. S. Geological Survey estimated that 40,000,000 tons of ore were disclosed by development work averaging only 35 feet below the surface of the ore. The ore is found along an area about one and a half miles wide by twenty miles long, and for the most part on the eastern and southern slopes or foothills of Three Peaks, Granite Mountain and Iron Mountain. Later estimates by others have gone as high as ore in sight 164,000,000 tons, probable ore 300,000,000 tons and possible ore 1,000,000,000 tons. Whether this last estimate is too great or not there is sufficient iron ore in Utah to justify the starting of an iron industry.Two companies are now mining iron ore in Utah, the Columbia Steel Corporation and the Utah Iron Corporation. The mine of the Columbia Steel Corporation is at Iron Springs a few miles west of Cedar City. About 650 tons, of ore a day is being shipped to the blast furnace at Ironton. The ore is mined by the glory hole method. After being drilled it is blasted to the bottom of the several glory holes and is dropped through chutes into cars on the ore haulage level below. It is then hauled by electric locomotives to the crushing plant, where it is crushed to blast furnace size before going to storage bins. Some of the softer ore is brought to the chutes by Fresno scrapers."

Jan 1, 1925

By Mona M. Fawzy, Ahmed A. Eliwa, Ebrahim A. Gawad, Ahmed H. Orabi, Amal E. Mubark

The growing demand for rare earth elements (REEs) has led to numerous recent studies to recover these elements from various bearing ores and wastes. Therefore, the recovery of REEs from Ras Baroud polymetallic concentrate has been investigated in the current study. Physical beneficiation for the Ras Baroud pegmatite sample was carried out, yielding a concentrate for euxenite (Y), fergusonite (Y), xenotime (Y), monazite (Ce), allanite, thorite, uranothorite and Hf-zircon, which resulted in raising the concentrations of REEs, Th, Zr, U and Ti in the sample. Fusion digestion processes with sodium hydroxide were studied using the conceived predictive diagonal (CPD) technique. The three experimental digestion groups proved the dissolution of 99.9, 95.6, 99.9, 52.5 and 0.47 percent for REEs, Th, U, Ti and Zr, respectively, under fusion conditions of 723 K, 120 min, 1/1.5 ore-to-alkali ratio, and smaller than 100-μm particle sizes. Fusion kinetics, isotherms and thermodynamics were investigated using several suggested models, namely, pseudo reversible first order, uptake general model and shrinking core model, which matched well with the experimental digestion results. Selective recovery of actinide content from the REE content of the digested concentrate chloride solutions was accomplished using solvent extraction with di-2-ethyl hexyl phosphoric acid. About 99.9, 99.9 and 4.2 percent extraction efficiencies for Th, U and REEs were realized, respectively, using 0.3 mol/L solvent concentration in kerosene as a diluent, 1/2 organic-to-aqueous ratio, aqueous pH of 0.2 and contact time of 15 min. Thorium and uranium ions were stripped with 2.5 mol/L sulfuric acid solution with 94 and 98 percent stripping efficiency, respectively. A highly purified REE precipitate was obtained from the raffinate solutions. Zircon mineralization tailings were obtained as a byproduct through the alkaline digestion process.

Oct 1, 2024

By Richard H. T. Garnett

Large scale, profitable, offshore mining of cassiterite started in 1907 around the coast of south Thailand and continues today in Indonesia. The more complex marine mining of diamonds commenced in the early 1960?s and is now an established industry off the coast of Namibia in southern Africa. The activities have involved many diverse organisations, and have required the development of new marine mining equipment. De Beers Marine, more recently as contractor to Namdeb, has been the dominant producer since 1989. Smaller, public, mining companies, registered in South Africa, Canada and the U.K., have achieved mixed performance results, but the total annual revenue from offshore diamonds now exceeds about US$ 180 M. With the benefit of hindsight, there are some useful lessons to be learned from the experiences. Mining of placer deposits at sea is more difficult and more costly than on land. It justifiably commences in response to a market demand for a product that cannot be supplied in sufficient quantity from onshore sources, not because the marine resource exists. The high costs can be offset in places by submarine grades so high that they have not been seen on land for a century. Technical and commercial success requires a combination, and a sufficiency, of ore reserves, capital, experienced people, and technology. Economic viability is not achieved easily and some diamond mining companies have experienced a very short productive life, terminating in their acquisition or liquidation. The reasons for failure in marine mining, regardless of whether the product is diamonds, gold, or tin, invariably are similar and fall into two categories. Those outside a company?s control include the sea conditions, taxation and fiscal climate, security of lease tenure, and the diamond market. The others, assignable to the company, provide important instructions for those who may aspire to advance the cause of marine mining.

Jan 1, 2004

By AIME AIME

THE Institute of Metals Division of this Institute held a joint meeting with the American Foundry- men's Association on Oct. 5-9, at Syracuse, N. Y. The registration at this meeting was about 150. There were four meetings in all, three of which were in con- junction with the American Foundrymen's Association. This combination works out very nicely and gives the I Division a number of practical foundry papers that it would not get otherwise. The sessions were well attended and the discussion was active. The session on Monday morning was of a general nature and consisted of the following subjects : " Refractory Problems in the Non-ferrous Electric Furnace Casting Shop, " "Temperature Control of Non-ferrous Alloys," "Atomized Coal System of Non-ferrous Melting," "Material Handling in a Brass Foundry." On Tuesday morning, the session was on "Aluminum and Its Alloys." The paper on permanent mold castings created a large amount of discussion, in fact so much that it had to be renewed after the close of the regular program. Aluminum is assuming a more important place every year and adds greatly to the program as a whole. One of the most remarkable meetings that this Division has ever had was held on Tuesday at noon in the form of a Round Table discussion, headed by G. K. Elliott, chairman of the Division, Cincinnati, Ohio. Mr. Elliott divided the members present, numbering about 80, into groups as they were seated at the tables. Each of these groups suggested a topic for discussion. They were as follows : "Fluxes on Market ;" "Simplification of Alloys;" "Pyrometric Control;" "Effect of Gas- sing Metal and Control;" "Barium Sulfate Added to Electric Furnace to Create Slight Oxidation to Remove Aluminum and Silicon;" and" Nickel in Brass."

Jan 1, 1925

By William P. Blake

(Canal Zone Meeting, November, 1910.) A DEPOSIT of manganese-ore near Tucson, Ariz., merits notice by reason of the peculiar form in which it occurs, and as a striking. example of ore-deposition by vadose upward capillary flow of metal-bearing solutions with concentration at the surface of the country-rock. This deposit occurs at the northern end of the Coyote mountains, about 40 miles west of Tucson, upon the outcropping beds of porphyritic rock, which appear to be partly-metamorphosed strata of volcanic tufa, probably of late Secondary or of Tertiary age. The strata dip northward at a low angle, and present a series of basset-edges in parallel lines of outcrop, east and west, facing the south and extending over many acres. Successive groups of these outcrops, from 5 to 20 ft. in breadth, are coated with oxides of manganese in lustrous black films and crusts, shining in the sunlight like polished ebony, and covering the whole surface of the rock above the soil. Seen at a little distance, these croppings look like solid ledges of massive and pure ore; but closer inspection and a few blows of the hammer reveal their true nature as a superficial coating allied in origin to the blackened shining surface of rocks exposed in desert-regions, familiarly known as " desert paint" or "desert varnish,"' similar to the phenomena described by me in a former paper, but much thicker and heavier. * By reason of the death of the distinguished author, this communication, probably his last communication to technical literature, is published without revision of the proofs by him. A term first given y G. K. Gilbert. See Rocks, Rock-Weathering, and Soil; by George P. Merrill, p. 256 (New York, 1897). Superficial Blackening and Discoloration of Rocks, Especially in Desert Regions, Trans., xxxv., 371 (1905).

Sep 1, 1910

By E. J. KENNEDY

THE 142D MEETING of the Institute is rapidly shaping up with splendid prospects of a strong technical program and the lighter side of this annual occasion amply provided for. The date is February 20 to 23. The technical sessions will be held in the Engineering Societies building; the smoker-dinner, the informal dance, and the annual reception and dinner, at the Commodore Hotel, Monday, Tuesday and Wednesday respectively. The news to date on the technical side is as follows: Mining Methods-Subsidence The Mining Methods Committee has prepared an interesting program which will be divided into two sessions to be held early in the week. At the first there will be papers on mining methods and development, including a description of the "Sinking and Equipment of No. 2 Shaft at Minas de Matahambre," by Dudley D. Homer and R. H. Cromwell. They describe in considerable detail the equipment used and the practice followed in sinking this important shaft, giving detailed costs and performance figures. Hoist¬ing ?arrangements and mining practice at the "Red Ore Mines of the Woodward Iron Co. at Bessemer, Ala.," are described by Tenny C. DeSollar, superintendent of mines, in a second paper. At this session of the Mining Methods Committee, H. M. Roche and R. E. Crockett, of the Committee on Eastern Magnetite Mining and Milling Methods, will present their paper, "Iron Ore Mining at the Scrub Oak Mine." This mine is in the highlands of New Jersey about 40 miles west of New York City. Prof. Robert K. Warner of Yale University will present a paper on "The Selection of a Mining System," which should have an interesting discussion. Pierre R. Hines, of Portland, Ore., will present, with stereopticon slides, his paper on "The Owyhee Tunnels, U. S. Reclamation Project, Owyhee, Oregon," describing one of the recent irrigation undertakings.

Jan 1, 1933

By Paul W. Richardson

"Introduction And AcknowledgmentsTHIS PAPER outlines the geology and discusses the geological problems of the Mindamar mine. It is impossible to acknowledge the contributions of ideas of all the geologists who have worked in the area. Among the more important contributors are K. DeP. Watson, W. S. James, B.S.W. Buffam, and L. J. Weeks, and John MacPherson, the resident geologist at the mine.A mineralogical and chemical study of the ore and country rock is being carried •on by Dr. Watson at the University of California, Los Angeles.General InformationThe Mindamar mine is on Cape Breton Island, forty miles south-west of Sydney (Figure 1). The nearest railway stations are at St. Peters, which is thirty-two miles southwest of the mine, and at Sydney. Good gravel-surfaced roads connect the mine to the railways.The mine is producing at the rate of 600 tons a day of ore containing zinc, lead, copper, and minor amounts of silver and gold. At the present time the mill feed averages 9 .per cent combined metals, of which zinc makes u:p 7 1per cent and lead and copper each 1 per cent.General GeologyThe ore being mined ,by Mindamar occurs in a shear zone parallel to a northeasterly striking, vertically dipping, series of rocks consisting of rhyolite tuff, rhyolite, minor more basic flow rocks, and diorite (Figure 2). In the vicinity of the mine, these rocks have been termed the Mine Series. They belong to the Bourinot group, which has been assigned by L. J. Weeks to the Middle Cambrian. At the latitude of the mine, the Bourinot group is bounded on the northwest by the Stirling fault and extends eastward for two miles."

Jan 1, 1953

By C Rothfuss, X Wang, S J. Herbert, K Prasad

The extraction of groundwater to produce gas from coal seam gas (CSG) reservoirs has highlighted the opportunity for beneficial uses of groundwater in Australia. This paper presents an assessment of alternate groundwater modelling approaches that can be used for assessment of one beneficial use option, that of injection. This assessment examines the outcome of the use of different simulation methods on predictions of hydrodynamic behaviour.In this paper, a simplified hydraulic concept of a multi-aquifer system within the hypothetical injection field was used to investigate the hydrodynamic behaviour of injection into the Precipice Sandstone. Comparisons were made through the analysis of a Theis 3D analytical solution with 2D and 3D numerical solutions. The paper discusses the different solution methods and the impact of these on predictions of pressure and flux. Differences in 2D and 3D solutions result in implications if planning injection as a beneficial use of water. For example, the 2D solution resulted in faster and higher injection pressure build-up when compared to the 3D solutions. The 2D modelling could result in either plans that require higher capital expenditure for a greater number of wells in order to spread the pressure effect and remain below the maximum injection pressure or a reduced injection rate. Meanwhile, the 3D modelling with sensitivity analysis could result in planning for lower capital expenditure for fewer wells required to spread the pressure effect and remain below the maximum injection pressure. CITATION:Wang, X, Herbert, S J,?Rothfuss, C and Prasad, K, 2013. Assessment of effectiveness of artificial recharge for coal seam gas water management based on numerical modelling, in Proceedings Water in Mining 2013 , pp 67-72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By S. Bang

In recent years, suction piles and suction anchors have been used as underwater foundations for various offshore structures. They have been proven very versatile, effective, and environmentally friendly. This paper describes the load resisting mechanism, installation, and design of suction piles and suction anchors. Also included are brief descriptions of three offshore structures that have recently been constructed using suction piles and suction anchors. They include: a new breakwater system utilizing gravity-type concrete caisson superstructure on top of concrete suction piles; a floating breakwater system utilizing embedded suction anchors; and a foundation system utilizing suction piles for temporary mooring of underwater tunnel elements.

Jan 1, 2009

By J. J. Brummer

The possibility of diamonds occurring in Canada was first raised by W. H. Hobbs in 1899, who concluded: "that the apex of the fan of diamond distribution probably lies somewhere in the strip of the territory bordering James Bay on the east." This was based on the occurrence of diamonds in surficial sediments at various locations south of the Great Lakes. There are two recorded discoveries of drift diamonds in Ontario: (a) the Peterborough Diamond, 33 carats in size, poorly documented and found sometime before 1920;and (b) the Jarvi Diamond, 0.255 carat, found during 1971 in Sheraton Township near Timmins . Both discoveries were in surficial sediments and their source(s) have not been located. During 1960, Selco Exploration Company Ltd. started a heavy-mineral sample program of river gravels in the James Bay Lowlands of Ontario. This was continued by Canadian Rock Company Ltd. (1962-1963) and the Ontario Division of Mines (1973). The surveys discovered the presence of kimberlite minerals in gravel samples from streams draining the Moose River Basin. A total of 53 pyrope grains, four magnesian ilmenites and one grain of chrome diopside were identified from 32 sample locations. A study of the distribution of these minerals suggested the kimberlite source rocks to be located along the north margin or within the Kapuskasing gravity "high" in the area immediately south of James Bay. The Jarvi Diamond, found on an esker east of Timmins, could well have originated from this area. During 1965, an esker was sampled by the Geological Survey of Canada, and the results attracted attention to the area south of Lake Abitibi. At 9 out of 34 sites sampled along the Munro esker, Lee recorded the presence of pyrope garnets and very minor chrome diopside.

Jan 1, 1978

By J. D. Miller

Physical separation of bitumen from low-grade Utah tar sand deposits containing a relatively high viscosity bitumen phase (Sunnyside and Tar Sand Triangle deposits) has been accomplished by traditional size reduction and froth flotation techniques. At appropriate experimental conditions more than 90 percent of the bitumen can be recovered in a concentrate, containing more than 20 weight percent bitumen, which should be a suitable feed material for subsequent hot water or thermal processing. The efficiency of bitumen recovery depends on the extent of size reduction, promoter and dispersant addition. Rejection of greater than 60 percent of the sand at ambient temperature and ease of water removal from the concentrate make such a process strategy both energy and cost effective. The energy required to achieve effective separation by the ambient temperature process is significantly less than the energy required for the recently developed hot water process. The flotation behavior of the tar sand has been analysed with respect to flotation pH, contact angle measurements and the apparent iso- electric point of the bitumen. The best flotation response at pH 7.8 to 9.0 can be correlated with the maximum in contact angle developed between the air bubble and bitumen surface and with the apparent iso-electric point of the bitumen (-pH 8.0).

Jan 1, 1981

PAST AND PRESENT CHAIRMEN OF DIVISIONS Institute of Metals Iron and Steel Mineral Industry Industrial Minerals Year Division Petroleum Division Division Coal Division Education Division Division 1918 W. M. CORSET 1919 " 1920 W. H. BASSETT 1921 " 1922 W. B. PRICE RALPH ARNOLD 1923 E. DEGOLYER 1924 G. B. ELLIOTT 1925 F. JULIUS FOHS 1926 P. D. MERICA 1927 11 JOHN. M. LOVEJOY 1928 S. SKOWRONSKI A. W. AMBROSE RALPH H. SWEETSER ' 1929 " J. B. UMPLEHY G. B. WATERHOUSE 1930 ZAY JEFFRIES C. V. MILLIKAN W. J. MACKENZIE HOWARD N. EAVENSON 1931 SAM TOUR C. E. BEECHER F. M. BECKET 1932 C. H. MATHEWSON EARL OLIVER F. N. SPELLER THOMAS G. FEAR C. H. FULTON 1933 T. S. FULLER W. E. WRATHER JOHN JOHNSTON ELI T. CONNOR " 1934 J. L. CHRISTIE H. D. WILDE, JR. L. F. REINARTZ " T. T. READ 1935 W. M. PEIRCE HARRY H. POWER A. B. KINZEL JOHN T. RYAN SAMUEL H. DOLBEAR 1936 E. H. DIX, JR. HALLAN N. MARSH C. E. WILLIAMS EUGENE MCAULIFFE WILLIAM B. PLANK OLIVER BOWLES 1937 A. J. PHILLIPS M. ALBERTSON FRANCIS B. FOLEY J. B. MORROW " CHESTER A. FULTON 1938 R. F. MEHL G. B. CORLESS J. T. MACKENZIE PAUL WEIR FRANCIS A.THOMSON J. R. THOENEN 1939 R. H. LEACH W. H. GETS J. HUNTER NEAD C. A. GIBBONS " M. M. LEIGHTON 1940 E. M. Wise T. V. MOORE F. T. SISCO C. E. LA WALL W. R. CHEDSEY W. M. WEIGEL 1941 D. K. CRAMPTON E. A. STEPHENSON C. H. HERTY, JR. JULIAN E. TOBEY " PAUL M. TYLER 1942 CARL E. SWARTZ HARRY P. STOLZ E. C. SMITH NEWELL G. ALFORD A. F. GREAVES-WALKER B. L. MILLER

Jan 1, 1942

By Samir N. Shoukry, Mourad Y. Riad, Gergis W. William

"Setting of concrete material is defined as the transitional period between states of true fluidity and true rigidity. Initial and final setting times are measured in the laboratory on the mortar sieved from the mix in a controlled environment where temperature and moisture values are constant. On the other hand, field applications are held in outdoor environments where environmental variations have direct impact on setting time values. In this study, initial setting time of class K concrete, usually used for bridge decks and concrete pavements, are investigated highlighting discrepancies between laboratory and field measurements. 72 mixes have been cast in variable environments and collected data from concrete mixes and the ambient conditions are reported. In light of the collected data, the effects of variable setting times on early age cracking of concrete material are studied and means to minimize such cracks are presented.BackgroundSetting of concrete material is defined as the transitional period between states of true fluidity and true rigidity [1]. Continuous hydration of the cement within the matrix transfers the mix from a state of setting to hardening. Initial and final Setting times are measured in a laboratory setting following ASTM C 403 specifications. Initial setting approximates the time at which the cement paste can no longer be plastic under compaction (or can be handled in a proper fashion), while the final setting approximates the time at which hardening occurs. The standard test described in ASTM C 403 is conducted on the mortar sieved from the mix (paste passing from 4.75 mm sieve opening). Initial and final settings are described as the elapsed time after the initial contact of water and cement till the mortar reaches a penetration resistances of 3.5 MPa (500 psi), and 27.6 MPa (4000 psi) respectively."

Jan 1, 2012

By C M. Rebagliati, J G. Payne, K Roberts

The Pebble deposit, located in south-west Alaska, is one of the largest Copper- Gold-Molybdenum (Cu-Au-Mo) porphyry systems in the world, with a current resource of >8 billion tonnes which contain 73.7 billion pounds of copper, 87.1 million ounces of gold and 4.16 billion pounds of molybdenum. The Pebble deposit formed at ~90 Ma, during emplacement of subduction-related hornblende granodiorite porphyry intrusions emplaced into Jurassic-Cretaceous sedimentary, volcanic and subvolcanic intrusive rocks of the Kahiltna Terrane. The Pebble West and Pebble East Zones represent two thermal and fluid centres in a single large magmatic-hydrothermal system. The West Zone extends from surface to about 500 m depth, has thin zones of oxide and supergene mineralisation overlying hypogene chalcopyrite mineralisation, and is amenable to open pit extraction. The East Zone extends to at least 1700 m depth, is higher grade, occurs beneath an eastward-thickening cover of younger sedimentary and volcanic rocks, lacks oxide and supergene mineralisation, and is being evaluated for underground block-cave mining. Most Cu-Au-Mo was introduced with early K-silicate alteration and related quartz-sulfide veins. In the East Zone, a structurally-controlled overprint by advanced argillic alteration significantly increased Au and, to a lesser extent, Cu grades. Exploration potential at Pebble and its surrounding district remains high. Several other porphyry, skarn and epithermal deposits have been discovered in the district, but only limited exploration has been conducted. The eastern, higher grade part of the Pebble deposit remains open in several directions, with significant potential for resource expansion by ongoing, aggressive drill exploration. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008