Search Documents

By P. Aguirre

Recovery of zinc, copper and nickel from electroplating waste solutions was achieved 'by using a Pulsated Percolated Porous Electrode "3PE" reactor on a pilot plant scale. Intensity - potential curves were used to study the possibility of metal removal and to define the working potential range. The present study describes the use of the 3PE reactors in several electroplating industrial units for the decontamination of their effluents. These effluents were issued from different industrial solutions such as cyanide, sulfate, chloride and Watts baths. Using the stripping curves, deposition rates and electrical efficiencies were determined as function of the metal concentrations in these effluents. Their decontamination could be achieved to the level of few ppm of metals with reasonable current efficiencies. The recovery rates of zinc and copper were about 93 and 99 %, respectively. The. treated effluents contained less than 7 and 1 % of the initial contents of Zn and Cu, respec¬tively. This process allows the recycling of the recovered metals and leads to water saving.

Feb 13, 2014

By G. Song

Magnesium has excellent bio-compatibility in terms of its density, strength, elastic modulus and toxicity. However, due to its poor corrosion performance, so far magnesium has not been successfully used in the human body as a permanent implant material. Nevertheless, there is a possibility to utilize the low corrosion resistance of magnesium to make magnesium into a temporary implant component that can gradually dissolve in the human body after surgical region heals. This will avoid the secondary operation to remove the temporarily implanted component and the chronic inflammatory discomfort caused by the implant. This paper is aimed at exploring the possibility of using magnesium as a degradable bio-material through investigating the corrosion behaviors of pure magnesium and surface treated magnesium in a simulated body fluid (SBF) solution. It was found that magnesium corroded rapidly in the SBF solution, resulting in vigorous hydrogen evolution and a strong alkalization effect. Hence, it is impractical to use magnesium as a permanent implanted material or even a degradable implant. However, a proper anodizing treatment can significantly improve the corrosion resistance of magnesium, and hence slower down the hydrogen evolution and alkalization processes, which will allow to control the corrosion or degradation of magnesium at a desired rate in the human body. With a controllable corrosion rate, it is believed that magnesium as a degradable implanted material will be eventually achievable.

Jan 1, 2006

Mount Isa Mines Limited (MIM) and the Commonwealth Scientific and Industrial Research Organization (CSIRO) have, over the past 15 years, jointly developed the Isasmelt process. This process is based on the use of the Sirosmelt top-entry, submerged combustion lance, developed by the CSIRO in 1973. While the Isasmelt technology was first applied to lead smelting, it has more recently been adapted to smelt copper concentrate. A 15 t/h demonstration Copper Isasmelt plant was commissioned in MIM's Mount Isa copper smelter in April 1987. The success of the Copper Isasmelt demonstration plant, which smelted over 532,000 metric tons of copper concentrate, has led to the construction of two full-scale furnaces: a 104 t/h furnace in the Mount Isa copper smelter, and a 585,000 t/y (650,000 short t/y) furnace at the Cyprus Miami Mining Corporation smelter at Miami, Arizona. The commissioning of these furnaces commenced in August and June 1992, respectively. The MIM Copper Isasmelt furnace will raise the Mount Isa copper smelter's capacity to 265,000 t/y of copper. The plant includes several innovative features, including: Andritz pressure filters, a rotary holding furnace, and an Ahlstrom flux-flow boiler.

Jan 1, 1993

By Fredy Llerena B.

El presente trabajo describe la geología del depósito minero Candelaria, perteneciente al distrito minero de Castrovirrey, Huancavelica. Dicho depósito está asociado a la actividad ígnea de centros y domos volcánicos del terciario medio o superior, mientras que la veta Candelaria está constituida por tetrahodrita, enargita, boulangerita, bournouita, jamesonita, esfalerita, galena, bismutinito, chalcopirita y como minerales de ganga, pirita, cuarzo, barita, oropimente, regelgar, marcasita, arsenopirita, así como hay lazos cimoidea. De otro lado, las intersecciones de vetas favorecen la mineralización y el Domo Volcánico Candelaria es favorable a la mineralización al igual que los tufos.

Oct 14, 1980

By O. Hall

STOPING at Noranda" is a sequel to "Mining at Noranda". "Mining at Noranda", presented in 1937 (1), sketches Noranda's history, metallurgical problems, exploration, mining methods, mining details, pillar extraction, and costs. "Stoping at Noranda" deals in greater detail with our stoping, the use of sub-level drifts instead of benches, and the drilling out of the stopes with jointed rock drill steel and diamond drills. Sun-LEVEL DRIFT STOPING: Sub-level drift stoping is almost universal throughout the mine and is the standard sroping method in both sulphide ore and rhyolite flux ore. The features that have led to the adoption of this standard are: (1) Continuous symmetrical drilling in sub-level drifts with no delay for blasting. (2) Large-tonnage blasts Saturday night after the drillers have left. (3) Comparative freedom from gas and smoke during the working days. ( 4) The daily safety achieved by having all stope drilling done in drifts. (5) The safety and security achieved by drilling out stopes, floors, and pillars before there is any weighting or cracking.

Jan 1, 1939

By J Rayner, R P. Langmead, J A. R Coote

Gosowong is situated within the Neogene magmatic arc of Halmahera island in the Maluku province of eastern Indonesia. It was discovered as the result of a rigorous ground reconnaissance program in an area with no previous mining activity. The broad structural setting in the Gosowong District comprises an elongate dome formed by the forceful upward intrusion of magma along a deep-seated structure, resulting in associated tensional fracturing trending parallel to the long axis of the dome. Four copper-gold porphyries and numerous low-grade epithermal veins occur within this mineralised corridor, with the Gosowong Deposit being the only economic occurrence discovered to-date. Gold mineralisation is hosted within multiphase epithermal quartz-adularia and quartz-chlorite fissure veins, breccias, and stockworks. High-grade gold mineralisation is emplaced in two gently south-plunging ore shoots along a 400 m section of the north-striking, east-dipping, Gosowong Fault, the primary control on mineralisation. The Gosowong Fault is believed to be a tensional fracture associated with uplift of the dome. Lithological variation and structural intersections play a large role in grade distribution within the vein zone. Host rocks comprise a wide range of shallow marine, intermediate-basic volcanic and volcaniclastic rocks of ?late Miocene age. The Gosowong gold deposit is a classic example of a low-sulphidation epithermal gold deposit, based on the abundance of adularia and illite in the alteration assemblage, and low base-metal sulphide content within quartz-adularia veins. The indicated resource is estimated at 0.99 Mt at 27 g/t Au and 38 g/t Ag for a total of 870 000 ounces Au, using a cut-off grade of 2 g/t Au.

Jan 1, 1999

By James O'Brien, Lyman Frost, S. Elangovan, J. Stephen Herring, Joseph Hartvigsen, Carl Stoots, Anthony Nickens

"Carbon dioxide recovered from concentrated sources, such as metallurgical reduction furnaces, cement kilns and fossil power plants can provide a valuable feedstock for a synthetic fuels industry based on energy from nuclear, solar, wind and hydropower sources. High temperature co-electrolysis of CO2 and steam to produce synthesis gas has been demonstrated using reversible solid oxide fuel cell technology. Where a source of high temperature process heat is available, such as from an advanced high temperature nuclear reactor or solar dish concentrator, the endothermic electrolysis reactions can utilize both thermal and electrical inputs in such a way that the conversion efficiency within the cell is 100%. Synthesis gas produced in a coelectrolysis cell has been further reacted over a catalyst to produce conventional hydrocarbon fuels. Widespread implementation of synfuel production from CO2 will enable a much larger reliance on intermittent renewable energy than can be accommodated by conventional electric demand profiles.IntroductionFor the past several years, Ceramatec, Inc and the Idaho National Laboratory (INL), have been studying the feasibility of high temperature solid oxide electrolysis for large-scale, nuclearpowered hydrogen production under the U.S. DOE’s nuclear hydrogen initiative (NHI) as an alternative to the thermochemical process. Parallel to this effort, the INL and Ceramatec have been researching high temperature co-electrolysis of mixtures of steam and CO2 to produce syngas:"

Jan 1, 2008

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing clay mining and crushing methods and costs at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might perhaps, in many instances, cause embarrassment to the individual operator as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this distinction in order that no misunderstanding of the scope of the cost tabulation shall ensue. The following report deals specifically with the methods employed by the Camp Brothers Company, Mogadore, Summit County, Ohio.

Jan 1, 1936

By J. J. Denny

IN November, 1932, an investigation of silicosis was undertaken at the Mcintyre Porcupine mine, Schumacher, Ont., after a discussion of the p"roblem with Sir Frederick Banting and his staff. As a result, it was decided to carry on dusting experiments with animals at the mine in a manner that would duplicate as far as possible actual industrial conditions. At that time 50 guinea pigs were placed in the crusher house tunnel of the mill where a considerable quantity of fine dust, containing approximately 35 per cent of free silica, was being constantly produced. These animals lived in this atmosphere for periods up to one year, and, while on autopsy large amounts of dust were found in the lungs, not a single case of silicosis had developed. These negative results suggested, among other things, that the mine gases might be a predisposing factor in the production of silicosis, and the results of this investigation (1) led us to undertake the study of the hydrogen-ion concentration of the condensate of the atmosphere, both in the mine and in various sections of the mill. The CO, combining power of blood serum on a series of 400 miners was also studied at this time. While these results were inconclusive, the variation in the hydrogen-ion concentration of the condensate between the surface and underground atmospheres encouraged us to investigate the effect of neutral, weak acid, and alkaline solutions on the solubility of siliceous materials. Gye and Purdy (2) were the first to point out that the chemical reaction, and not the physical presence of siliceous material, was responsible for the production of the fibrosis in silicosis. This work was investigated by Gardner and Cummings (3), who showed that the tissue reaction to quartz was definitely proportional to the size of the particle. They found that 1-3 micron particles of quartz produced an acute proliferative fibrotic response, while the 10-12 micron particles produced only a foreign-body reaction up to a period of three years. It is accepted that the dangerous silica particles retained by the lung are under 5 microns in diameter.

Jan 1, 1937

By B Oostendorp, R van der Merwe, P

In order to assess whether polysaccharide depressants are strongly or weakly and reversibly bound to the surface of talc, a series of experiments was conducted on New York talc in which the floatability of the talc in a microflotation cell was determined. The talc was conditioned in solutions of carboxymethyl cellulose (CMC) or guar gum in 10-2 ionic strength Ca(NO3)2 or Mg(NO3)2. The talc was then washed with four successive aliquots of water, or cation solution, to try to remove the polymer and the flotation response of the talc was assessed. CMCs of different charge (DS) were used to assess the effect of charge on the strength of bonding. The results show that CMC and guar gum could be removed to a large extent from the talc surface by washing with water (the floatability was restored), however very little could be removed from the surface by washing with cation solution. The higher charge CMC was easier to remove from the talc planes in the absence of cations than the lower charge CMC. Thus CMC bonding to talc has been shown to be irreversible or very slowly reversible only if cations are present, implying that cations are necessary to keep the polymer bound to the surface of the planes to effect depression. The presence of ions in solution also had the effect of maintaining surface coverage of the talc by guar gum.

Jan 1, 2005

By E. G. Noble

The potential for using heterotrophic microorganisms to solubilize manganese from low-grade domestic ores is being assessed at the Reno Research. center, U.S. Bureau of Mines. More than 90 pct of the manganese has been extracted from a variety of oxide ores in shake-flask tests using molasses as a source of .. nutrients for the microorganisms. It has also been demonstrated that high recoveries of manganese can be obtained from a domestic wad ore using column bioleaching. 'l'he isolation and identification of organisms responsible for manganese extraction is discussed, as are the mechanisms responsible for manganese solubilization.

Jan 1, 1991

Anomalous geologic or stress conditions ahead of the longwall face can cause great harm to both the individual miner and the mining operation as a whole. The U.S. Bureau of Mines has been developing seismic tomography techniques to image the panel ahead of the face. This paper presents the results of a field effort in which a 60-m (200-ft) segment of a longwall panel containing a fault zone was surveyed daily as the face approached. Stress distribution, geologic structure, and dynamic elastic properties within the panel were plotted and compared to static laboratory measurements. The surveys successfully imaged an anomalous stress concentration, likely influenced by the presence of the fault zone. The calculated dynamic physical properties generally agreed with laboratory measurements.

Jan 1, 1995

By P. C. Good

Tungsten metal in fused form and of high purity was prepared by reducing tungstic oxide with redistilled calcium metal in a heavy-walled sealed reactor. Alloys of tungsten with vanadium, molybdenum) chromium, columbium, and tantalum were prepared by coreduction of mixed metal oxides in the same manner. This work was undertaken by the Bureau of Mines to investigate new approaches for preparing tungsten and its alloys in high-purity form. The standard method of producing tungsten metal has been the reduction of tungstic oxides by hydrogen. The resulting metal powder is compacted, sintered, and fabricated by powder metallurgy methods. Long experience in this field has resulted in the development of a technology that (by careful control of the variables such as metal composition, particle size, and sinterng technique) is well adapted to producing wire and the small shapes usually prepared from tungsten metal.

Jan 1, 1961

By W. A. Crosby

All mine operators using explosives want to maximize explosive performance while minimizing blasting costs. Use of bulk explosive products such as AN/FO, heavy AN/FO, slurries and emulsions has greatly improved blasting efficiency over the years. Many operators have improved energy output from these products by adding aluminum. A major problem facing them is the fluctuation in aluminum price. The question therefore becomes, when is it economically advantageous to use aluminum in bulk products? This paper answers this question by first reviewing the energy output from the main types of aluminized and non aluminized bulk mixed explosives and then by showing the relationship between the different products on a cost and energy basis. The paper finally presents examples of charts and tables which will aid mine operators to conveniently select the most economically correct bulk explosive, including the level of aluminum addition.

Jan 1, 1991

A mini- or micro-machine is a small electro- mechanical device. There are several existing applications of micro-sensors such as the accelerometers used in automobile airbags or the force sensors and grippers used at the ends of micro-surgery tools. Potential applications of existing mini- and micro-technologies are possible and could be used to improve the control and efficiency of fragmentation, heap leaching and other mining and mineral processing operations. A more radical proposition is to devise mass-produced, possibly disposable, minimachines that would operate in large groups. These would be the basis of highly selective, efficient, flexible, and clean mining and mineral processing methods. The paper is intended to promote discussion of how innovative applications of mini-technologies can be used to improve and radically change current mining and mineral processing methods.

Jan 1, 2002

By L. Y. Sadler

The Bureau of Mines conducted a study Lo determine the loss in weight of silica (Si02) volatilization from low-alumina (A1203) refractories used as hot face liner materials in such process equipment as coal gasifiers, synthesis gas transfer lines, and ammonia plant secondary re-formers. Small specimens of 80-and 40-pct-A1203 brick and 95-pct-SiO2 brick were exposed to steam in high-pressure furnaces at pressures of up to 1,000 psig and temperatures up to 1,400° C for periods ranging up to 120 h. Weight losses from the 40-pct-A1203 brick after 40 h of exposure were highest, 2.75 pet at 1,400° C and 1,000 psig. The rate of weight loss had dropped to near zero after 80 h of exposure at all temperatures. No relationship between total silica content of the specimen and weight loss could be established nor did scanning electron microscopic examination of the specimens before and after exposure identify specific regions (e.g., surface) suffering a disproportionate share of the silica loss. It was concluded that minor silica volatilization is likely to occur, if at all, at temperatures of less than 1,000° C and pressures below 1,000 psig, and that low-alumina refractories should be used as dry-ash coal gasifier hot face linings.

Jan 1, 1986

By D. D. Aksenova, V. A. Ignatkina, L. A. Samatova, A. V. Lygach, E. D. Shepeta

Calcium minerals such as scheelite, phosphate, apatite are valuable minerals, which have similar flotation properties to the calcium gangue minerals. An additional problem is the fine dispersion and close mineral association of valuable and other minerals. Low polar compounds (non-ionic surfactant), such as fatty iso alcohols, neonol and phosphol, and their combinations with sodium oleate have been studied using flotation of monominerals and ore flotation; ATR IR spectroscopy and TEM for study surface of minerals; UV spectroscopy for control solubility, aggregation and de-aggregation processes. Increase in solubility of fatty acid collectors was confirmed by low soluble (heteropolar) compounds. Oxyethylated esters of phosphoric acid are adsorbed on phosphorite by -O2PO2R2 and on other rock minerals by donation of OH bond. Same effect shows difference of adsorption of fatty iso alcohols on calcite and scheelite. The different forms of adsorption of ionic and nonionic compound on a sparingly-soluble mineral surface creates distinction of the flotation kinetics and technological balance of ore flotation. The results of the separation of flotation of scheelite from calcite depend on the order of pouring into pulp of fatty iso alcohols and oleate, and their ratio in the mixture. Increasing scheelite recovery into rougher scheelite concentrate by 3.6% for both the flotation and sludge classes was obtained. Calcite recovery varied slightly upwards or downwards by 0.8-2.4%. The use of the non-ionic surfactant phosphol in combination with a fatty acid soap allows for obtaining a phosphate concentrate with more than 28% P2O5 content and almost 80% recovery in flotation operation. It is not obtainable with other reagent regimes. Keywords: Flotation, calcium minerals, oleate, fatty isoalcols, neonol, oxyethylated esters, adsorption

Jan 1, 2020

By D. P. Patil, B. K. Parekh

Water is the mainstay for beneficiation of fine size coal and minerals; however, it is also the least desirable constituent in the final product. The basic concept of the novel process described in this paper is based on the differential surface heat conduction/ absorption capacity of individual particles, which differs for different species of minerals. When a mixture of fine material is exposed to a radiant energy source, the various solids present in the mixture will absorb heat energy depending on their heat-conducting properties and there will be a difference in the surface temperature of the particles. When this differentially heated solid mixture is placed on a moving belt, which is coated with a low temperature melting resin, the hotter component of the mixture will stick to the belt and relatively cooler particles will stay free on the belt and fall off at the end of the belt run. Experiments were conducted with pyrite, coal, and quartz of 6 × 18 mesh particle size. The goal of the test program was to find the optimum conditions at which there exists a required temperature difference between minerals and coal particles by controlling the operating system variables. Preliminary tests results showed that there is a potential for separating mineral matter from coal using the thermo-adhesive separation technique.

Jan 6, 2022

By L Nienaber

Mines, after becoming operational, often retain the same support and reinforcement designs developed in the feasibility study. These designs are conceived from limited drilling data and regional experience, thus having an empirical flavour. Empirical designs are perceived to be conservative, catering for a variety of failure mechanisms, which are not always present in mine development drives.This begs the question: If you were to invest in the necessary resources to obtain sufficient data and complete the required analyses for the different development drives in the mine, to engineer a support and reinforcement scheme with the capacity to match the demand of the rock mass, what is the difference in cost when comparing an empirical design to an engineered design?To answer this question, mine tunnels with different geometries and orientations, where detailed structural data was available, were selected for a comparative design exercise. Material cost, development cost, cycle time and professional fees for engineered and empirical designs were estimated. The outcome is summarised in the following paper that discusses the process followed and the results of the design comparison.

Mar 8, 2011

By AJ LYNCH

Broken Hill metallurgists have been responsible for some of the most important developments in mineral processing technology. These occurred mainly in two periods, 1902 - 15 and 1955 - 70. Mineral flotation was developed as an industrial process during the first period and this happened in two stages, the recovery of zinc minerals from the tailings dump accumulated during the gravity concentration of the oxidised ores and the selective recovery of galena and marmatite during flotation of the primary ores. During the second period fast accurate analytical procedures were developed to provide rapid assessment of process performance, and new means of controlling the process were devised which improved throughputs, grades and recoveries. These technological successes were due to the skills of the metallurgists and the commitment of the companies. They brought large financial returns. They were achieved under difficult circumstance. There are important lessons to be learnt from these successes.

Jan 1, 1992