Search Documents

By E. Neumann

With fuel costs unstable but escalating, solid fuels are playing an increasingly larger part in industrial concerns. Coal, petroleum coke and wood are examined from a burner system design viewpoint and from operational experience in kilns, hot gas generators, etc. The burner of today must also handle multi-fuel tasks and allow immediate, painless switching from one fuel to the next as well as the simultaneous burning of two or mope fuels. The paper discusses the principle of burning alternate pulverized fuels as well as the practice both in the United States and around the world.

Jan 1, 1983

By W. G. Pariseau

Introduction Caverns of 50 m in linear dimension at depths below 2300 m with a life of more than 25 years are proposed for the next generation of water-filled neutrino detectors. Little precedent exists for excavations in such an extreme environment, although some guidance is available from mining experience at great depths, for example, in South Africa, in Canada and at the former Homestake Mine in the U.S.A. Unlike mining for ore, there are choices available in the construction of such caverns that may mean the difference between success and failure. These choices should be informed by rock engineering principles. Recently proposed guidelines for orientation of brick-shaped caverns where the long dimension is a small multiple of the short dimension indicate that the most favorable orientation is with the long and short dimensions parallel to major and minor preexcavation principal stresses (Pariseau, 2005). Numerical analyses at reduced strength indicate some yielding at cavern walls should be expected but that an equilibrium state is quite possible and is aided by arching the back into a spherical dome when the cavern is an empty cylinder (Tesarik and others, 2002). The same indications of stability occur with brick-shaped caverns. However, the most dangerous situation occurs during the excavation sequence to final cavern dimensions. There are any number of excavation sequences that lead to the same final cavern shape, so there is an opportunity to partially optimize the sequence with construction guidelines that minimize peak stress concentrations during construction. This contribution discusses three practical excavation sequences that lead to the same brick-shaped cavern in the strong, massive Yates formation at the Homestake Mine where considerable rock mechanics data has accumulated through the years(e.g., Pariseau, 1985, Pariseau and others, 1995) and where actual mining on the 8000 Level indicates a strong possibility of successful investment in the next generation of large, deep neutrino detectors. The main results are: (1) a favorable brick-shape is one with dimensions in the same proportion as the preexcavation principal stresses (compressionpositive), and (2) favorable orientation of the most extreme but temporary shape of excavation is also best for the construction sequence. Analysis results from a mix of Homestake Mine data and possible excavation geometry illustrate the advantages of these guidelines.

Jan 1, 2006

By P. C. Miller

The paper reports laboratory results from the bioleaching of chalcopyrite ores and concentrates using a mixed moderate thermophile culture. Copper dissolution in excess of 95% was achieved in all cases with the majority of tests indicating copper dissolution in excess of 98%. Aspects of downstream processing are discussed in relation to iron rejection by precipitation. The laboratory results indicate the need for careful control of the pH value to prevent co-precipitation of the copper with iron. A comparison of capital and operating costs is given indicating potential differences between the use of toll smelting and bacterial leaching on site. A discussion is given highlighting the sensitive cost areas of these two process routes.

Jan 1, 1997

By M. M. Monte

A method for removing metallic mercury from contaminated tailing, using the flotation process, is described. In order to define some relevant parameters for the mercury flotation system, microflotation and electrophoretic mobility tests were carried out on (pure) metallic mercury in the presence of several surfactants. Based on the results obtained from fundamental studies a series of bench scale flotation experiments with mercury containing tailings from two wetland sites in Brasil were done. The results of microflotation tests with mercury showed that by using cetyl trimethyl ammonium bromide, an increase in mercury flotability is observed in the acid pH range, whereas in the presence of potassium oleate the highest mercury flotability was found in the alkaline pH region. The mercury flotability using potassium amyl xanthate was improved by the addition at sodium dithionate as an activator. The bench scale flotation tests with contaminated tailings from Poconé (brazilian wetland site) showed a recovery of 70% when sodium dithionate was used as activator and potassium amyl xanthate as collector. The resulting coefficient of separation is around 60%. However, the results of the flotation experiments with fine fractions from amalgamation tailings from Peixoto de Azevedo (brazilian wetland site) showed a low mercury recovery (32%).The results from this work suggest that since in the Poconé site tailings, the metallic mercury is not completely associated to the finer particles, the flotation process to recover the metallic mercury seems very promisor.

Jan 1, 1996

By P. D. Lee

The effect of strontium on porosity formation in aluminum-silicon alloys is not well understood and there is no consensus upon the cause of the effects observed. This paper describes a series of experiments where the effect of adding strontium on pore formation was observed directly with combination of a traditional temperature gradient stage and real time micro-focus radiography. These in situ observations provide a new insight into the effect of strontium on the nucleation and growth kinetics of porosity. The addition of strontium was found to have a minor effect on the growth of the pores in the mushy zone. However, strontium appeared to alter the nucleation and stability of hydrogen bubbles within the melt. The interaction of strontium with titanium-boride grain refiners produced an even stronger change in the nucleation and stability of the bubbles formed.

Jan 1, 2002

By Calvin Konya, Anthony Konya

Presplitting is a form of blasting that when executed properly will create a smooth wall that will minimize secondary conditioning. In recent years, presplitting has become a popular technique to be used in both the mining and construction industries, however, presplitting fails on many occasions because of ‘geologic conditions’. This is typically because of improper explosive loads consisting of overloading and underloading blastholes. In this paper the authors introduce new factors such as a presplit factor which varies for different rock types, selection criteria for the spacing of presplits, and the optimization of explosive load for the technique of Precision Presplitting.

Jan 1, 2017

By A. Gakwaya, K. Ba, M. Guillot, J. Levesque

"In the aerospace industry, parts requiring tight dimensional tolerances and high mechanical properties are often produced by forging. This forming process allows for an optimal use of the material and can produce high quality parts at a reasonable cost. Thanks to CAD techniques, it is now easier to predict flow profiles and in-process defects occurrence as well as wear of the forging dies. However, in order to determine the properties of the forged part with computer simulation methods, a good material constitutive law is a prerequisite. This paper presents a virtual manufacturing process modeling for the closed die forging of a workpiece performed with Abaqus. The hot closed die forging is a regular process applied to manufacture metallic components used in aerospace industry. In this forming process, the material flow and final properties depend on the microstructure evolution during the process that is why it is important to include the microstructure effects in the material model. Based on the stress-strain data measured experimentally, the material parameters of the standard (classical) Johnson-Cook constitutive model and of a modified Johnson-Cook constitutive law including the microstructure effects have been determined. The obtained simulation results are compared with the experimental results for validation.INTRODUCTIONDue to their good physical and mechanical properties such as ductility, fatigue strength, corrosion resistance and rupture, aluminium alloys are often used in the aeronautic and the automobile industries. In this work, we present the forging of an Al-Zn-Mg-Cu alloy, a high strength aerospace alloy recognized for his good combination of physical and mechanical properties. The forging process is simulated in Abaqus Explicit using both the standard Johnson-Cook law (Johnson & Cook, 1983; Hor, 2011; Lin et al., 2012), and its modified version as proposed by Andrade et al., (1994). The Johnson-Cook law offers the advantage of considering the coupled effect of the plastic strain, the plastic strain rate, the temperature of forging and the hardening effect. However, it is a phenomenological model which does not account for the effect of the microstructure evolution. In this work, a modified Johnson-Cook model implemented in a user subroutine is used. It includes the effect of the dynamic recrystallization phenomenon during the hot deformation. The dynamic recrystallization has a noticeable influence on the microstructure and on the properties of the material. The term dynamic means that the process starts and acts during the deformation and this is different from the static mechanism of recrystallization which occurs during an annealing and after cold or hot deformation. Since properties of the alloy used in this work are not readily available in the literature then characterization tests have been done at various temperatures and strain rates, in order to determine the thermomechanical properties and the material behavior during the process of hot forming, more precisely during the hot forging process."

Jan 1, 2016

By Heribert F. Broicher, Arne Volland

The application of remote sensing techniques combined with fluorescence spectroscopy is realised in analytical devices called LIF Analysers. The analysis of laser-induced fluorescence facilitates non-destructive, non-contact, on-line and real-time rock identification and quality control of bulk solids in transport. LKAB of Sweden was the first company to test LIF Analysers in the Kiruna Mine for bulk sorting of run-of-mine ores depending on the phosphorus content. Other applications tested in Germany so far are quality control of limestone (iron and/or dolomite content) and rock identification in lignite mining. Of special interest also is rock identification in diamond mines for dilution control. The paper summarises the present state of the application of LIF Analysers.

Jan 1, 2003

By D Laurence, L Ge

This paper demonstrates use of remotely sensed imagery in promoting sustainable mining. Remote sensing technology can be used during all phases of a mining project û from evaluating the resource, to making extraction more cost-effective, through to monitoring, mine closure and remediation. Use of the new generation of satellite platforms with the capability of acquiring satellite data with higher spectral and spatial resolution have the capability to emerge as essential indicator for sustainable development in the minerals industry. A life cycle approach to satellite imagery is discussed. The use of an imagery of the site prior to mining activity establishes the environmental baseline, guides mitigation measures and eventual help in suggesting remediation. Remote imagery provides the cost-effective means of monitoring reclamation, including the growth of planted vegetation, of the mine site and surrounding area. The latest advancements in satellite remote sensing are highlighted to meet the newer challenges of sustainable mining practices. Some of the worldwide successful remote sensing applications for the measurement and evaluation of the sustainable development impact of mining operations are described. Presently available source of imagery and its comparative advantages and disadvantages are provided as a guide. Finally, the limitations of this tool are indicated.

Jan 1, 2009

By Beall, John V.

THIS is not simply the story of how a water filled shaft was developed into a million-ton- a-year producing mine in the space of four critical years, although it is reason enough for telling it, but it is also the saga of an engineering achievement in which knowledge nurtured by years of experience in coal and ore mines was blended together and the best from each type of mining selected. The entire system of mining was detailed on maps by the mining engineering department before the shaft was unwatered, and subsequent development followed these plans nearly to perfection. The selection of machinery was particularly critical as it was necessary to push production from only a few headings in the early stages of development and metal mine machinery was being used in a coal panel-system of mining. At the start of World War I1 the demand for iron ore to supply Woodward blast furnaces, and rapid exhaustion of the main source of Wood- ward ore, No. 3 Red Ore mine, necessitated speedy opening of the Pyne mine. The mine is three miles southwest of Bessemer and is responsible for 80 pct of Woodward ore, the rest coming from the Songo mine. The Woodward Iron Co. is one of the old producers of the Birmingham district. S. H. Woodward, an iron-master of Wheeling, overheard two Union soldiers conversing about ore and coal lands in Alabama, which lead to the acquisition of the first ore lands of the Woodward Co. in 1869. Development was not begun until after the death of S. H. Woodward; his two sons, W. H. Woodward and J. H. Woodward, formed the Woodward Iron Co. in 1881 and purchased a tract of land midway between the ore vein on the southeast and the coal field on the northeast about 12 miles southeast of Birmingham for the

Jan 1, 1950

By Huan-Qiang Zhang, Gang-Hai Huang, Yu-Yong Jiao, Fei Zheng, Zhang. Xiu-Li

An efficient and accurate three-dimensional (3-D) contact detection algorithm is of vital importance in large-scale computing of discontinuous deformation analysis. The contact detection algorithm takes up a large proportion of the whole calculation time because of the increasing calculation number in three-dimensional case. For block systems which consist of convex polyhedrons, the efficiency and accuracy of the contact detection algorithm is a great challenge. The presented contact detection algorithm in discontinuous deformation analysis (DDA) method is carried out in three phases: the global neighbour searching, the local contact type searching and the contact transferring. A contact detection algorithm for 3-D DDA is presented with some improvements on the three phases. A grid-based global neighbour searching algorithm is used to eliminate unnecessary neighbour blocks to the exact number. The local contact type searching includes two steps. In the first step, the common plane method is used to determine the contact type between convex polyhedrons. In the second step, the contact pairs detected by the common plane method are divided into four basic types. In the third phase, the four contact types are transferred into two basic contact types, vertex-to-face contact type and edge-to-edge contact type, which are managed in a uniform procedure. Three verification examples are calculated, the results show that the proposed algorithm based on the three contact detection phases is robust and efficient.

Jan 1, 2015

By Adrian Moore, Bryan Goodwin, David Fales, David Lam

This paper describes the development of blasting protocols used to successfully create a 450m long blast fractured permeable trench in a basalt aquifer up to 20m thick, at a petrochemical facility in Australia, to enable the remediation of contaminated groundwater.

Jan 1, 2011

By Y. Ren, B. Yang

The magnetic field characteristics due to electromagnetic stirring in the secondary cooling zone of an extra-thick slab during continuous casting are numerically determined using Maxwell's equations, with particular emphasis on the distribution of magnetic induction intensity and electromagnetic force, as well as the influence of process parameters on the magnetic field. The orientation of the electromagnetic force is the same when the electromagnetic stirrers at the 30° and 60° posistions of the arc-shaped slab are powered in the same direction; otherwise, the orientation is opposite. The magnetic induction at the centre of the section of the stirrer's central axis at the 30° positio, as well as the current, frequency, and fitting formulae, are as follows: B = {0.075I.(1/A)-0.3} mT and B = {-1.75f.(1/Hz)+22} mT. The electromagnetic force and current fitting formula at the central point of the B-B section is F = {0.03168I2.(1/A2)-03.762I.(1/A)+326.7} N/m3, and the fitting formula of electromagnetic force and frequency at the centre point is divided into two segments. The first takes the form of a parabola: = {-21((f-4.3).(1/Hz)2)+970} N/m3, and the second segment is negative linear: F = {-1.65f.(1/Hz)+51.5} N/m3.

Apr 16, 2024

By Thales Renó Grilo

O presente trabalho teve como objetivo analisar as diferentes microestruturas do aço inoxidável duplex UNS S32304 obtidas pelo processo de soldagem Gas Metal Arc Welding (GMAW). As regiões do metal base, zona fundida e zona afetada pelo calor foram investigadas nos corpos de prova com diferentes aportes térmicos. As microestruturas obtidas foram caracterizadas utilizando-se a microscopia óptica (MO). As imagens de Mo obtidas na zona afetada pelo calor mostram que a fração de austenita aumentou com o aumento do aporte térmico. Este aumento está relacionado ao alto teor de cromo e molibdênio presentes no metal de adição utilizado na soldagem. Na zona fundida, a fração de austenita de widmansttaten foi observada com maior frequência na microestrutura do corpo de prova soldado com o aporte térmico de 1,87KJ/mm. Essa maior fração de austenita de widmansttaten observada para o aporte térmico de 1,87KJ/mm está relacionada com o maior tempo de permanência em altas temperaturas deste corpo de prova em relação aos outros corpos de prova investigados. Vale ressaltar que a adição de nitrogênio também promove a formação desta fase. De modo geral, os resultados da metalografia quantitativa mostram que a porcentagem de ferrita foi superior a 65% nas zonas termicamente afetadas e fundidas.

Aug 17, 2017

By Heloíza Döering Gasparin

Os efeitos de elevadas temperaturas e do tempo de exposição sobre as propriedades mecânicas de um ferro fundido cinzento hipoeutético foram avaliados em amostras de dois ferros fundidos da classe FC300, de mesma base, com diferentes percentuais de molibdênio. Ensaios de tração até ruptura a quente foram realizados em corpos de prova com diâmetro de 10 mm, usinados de um pino bruto de 30 mm de diâmetro. Os ensaios foram realizados a frio (temperatura ambiente) e a quente (200°C, 300°C, 350°C, 400°C, 450°C, 500°C e 550°C). Os tempos de exposição a elevadas temperaturas, após homogeneização térmica do material, foram de 0, 60, 90 e 120 minutos. As amostras com maior percentual de molibdênio (0,27% em peso) apresentaram melhores propriedades mecânicas para todas as condições ensaiadas. De acordo com a literatura a redução na resistência mecânica com a elevação da temperatura é atribuída à ocorrência de decomposição da perlita, como resultado da difusão do carbono vindo da cementita às lamelas de grafita, que é o responsável pelo aumento da quantidade de grafita no material. As análises metalográficas evidenciam a ocorrência deste fenômeno. Aumentos no tempo de exposição a temperaturas elevadas também contribuíram para a degeneração da perlita.

Aug 7, 2018

By Gabriel Mendes de Almeida Carvalho

O processo de soldagem de pontos por resistência elétrica é uma técnica econômica e adequada para a união de chapas, pela alta velocidade e adaptabilidade, torna-se um método amplamente difundido para a produção em massa. É utilizado principalmente em carrocerias de automóveis por apresentar elevada eficiência e qualidade. Este artigo analisa as diferenças apresentadas nas microestruturas de pontos de solda produzidos através do controle da refrigeração do eletrodo. Para garantir a qualidade de uma junta soldada e aumentar a vida útil do eletrodo é importante que os parâmetros empregados na soldagem sejam bem ajustados, para que o ponto de solda também apresente características que irão garantir uma boa performance do produto final. O objetivo deste trabalho é fazer a comparação da qualidade dos pontos de solda produzidos, além de avaliar a estrutura formada em diferentes temperaturas do eletrodo no momento da soldagem.

Aug 17, 2017

By G. A. Gamble

Fans used to ventilate subway, passenger rail and vehicular tunnels are similar to the fans used to ventilate underground mines. However, tunnel ventilation fan systems are typically designed to meet NFPA 130 or 502 standards, while mine ventilation fan systems must comply with the appropriate federal mine safety regulations. As a result, fan operation requirements and performance criteria, as well as typical fan and duct configurations differ significantly for tunnel and mine ventilation applications. Variations in environmental conditions in tunnels as compared to mines also result in differences in fan performance and material specifications. The need to enclose tunnel fans within building structures creates space restrictions impacting fan size selection that are not commonly encountered in mine fan installations, resulting in different approaches to selecting fans for the two types of tunnels. This paper discusses the various similarities and differences in design considerations for tunnel and mine ventilation fans.

Jan 1, 2009

By D. Brady

The need for onsite gas monitoring during, or following, a major incident at an underground coal mine has long been recognised. Recommendations from inquiries following Queensland mine disasters have included ?qualified persons and equipment for rapid analysis of gas samples be available in times of emergency? and that ?this may be accomplished by either mobile laboratories or laboratories established in each mining locality.? Following the Moura No. 2 disaster, the Queensland Government allocated funds to Simtars for a mobile laboratory to respond should such a disaster occur again in the future. This vehicle was commissioned in 1997 and has been used at many mine sites under a wide range of scenarios. Simtars, armed with over ten years of operational experience with this mobile laboratory, has taken an active role in the design and construction of a modernised replacement unit. With a twenty point tube bundle system and ultrafast gas chromatograph the result is, arguably, the best equipped mobile gas analysis laboratory for mine emergency response in the world. This paper outlines the features of the new laboratory, its capabilities and the philosophy behind the design and inclusions.

Jan 1, 2012

By D. Loring, J. Almgren

Climax Molybdenum Company’s Henderson Mine is a large panel caving molybdenum mine located about 43 miles west of Denver, Colorado. Three Joy M120-72-880 fans are installed in parallel on the No. 1 exhaust shaft. Throughout the mine’s history, ventilation changes such as the completion of the No. 5 exhaust shaft have decreased the utilization of these fans. To optimize fan performance they have been run with the full complement of 16 blades, down to as few as four blades. Since the completion of ventilation upgrades associated with the Henderson 2000 project, one surface fan has been operated under normal conditions with 10 or 12 blades. With the completion of a new network model of the Henderson ventilation system, a tool was built to develop fan curves for possible future fan configurations and predict future fan performance. This paper describes the tool and its use at Henderson.

Jan 1, 2007

By V. I. Lakshmanan, D. A. Mackie

"1. INTRODUCTIONIn the past two decades, low-grade gold and silver ore bodies in the United States have been exploited by heap leaching, primarily with sodium cyanide solutions. This method has proven to be a viable alternative to conventional milling due to its low capital and operating costs. Successes have been made, particularly in Nevada, where ores are well oxidized and the climate is conducive to this method. in recent years, heap leaching has been tried in northern latitudes with some success, however, in using this method, operators face more severe limitations than do their neighbours to the south.This paper evaluates the limitations of heap leaching with particular emphasis on northern climates and introduces an alternative method to recover precious metal values in a continuous vat. This proprietory technology, known as the Mackie Vat Leaching Jig, shows promise, with improved gold recovery and potential to operate in cold climates.2. WHAT ARE THE LIMITATIONS TO HEAP LEACHING?Heap leaching of non-refractory ores is subject to the following limitations:1. Minimum amount of free gold and nuggets in the ore.?. Minerology of the ore--accessibility of gold to lixiviant.3. Minimum particle size and size distribution of crushed product to allow percolation of lixiviant through the heap.4. Minimum amount of clays or clay-like slimes that can cause coating of ore particles and channelling of lixiviant.5. Minimum strength of ore particles or agglomerations to allow economic height of heaps to be built.6. Amount and suitability of real estate.7. Amount and type of precipitation.8. Ambient temperatures.9. Possible poorer lixiviant diffusion.10. Possible lower oxygen content in dissolved cyanide solution with higher heaps, particularly with ice and snow cover."

Jan 1, 1989