Search Documents

By J Rock, K Bambrook

"Hanwha Mining Services was approached by Glencore Coal to provide a series of (trial) demonstration blasts at its Clermont coalmine. The intent of the project was to trial a bulk explosive product that would be able to provide sufficient energy for the ground type encountered without production of post-blast fume. Three blasts were loaded using the patented XLOAD bulk explosives with a density of 1.00 g/cc. XLOAD bulk products are water resistant explosives that can be loaded at densities much lower than traditional (generic) water resistant heavy ammonium nitrate – fuel oil (ANFO) or pumped blends with significantly reduced risk of fume. In addition, these products have detonation characteristics that generally deliver a higher heave partition than conventional bulk products and hence improve muck pile looseness and digability.The priority key performance measures included the absence of fume from blasting, being at least cost neutral and providing similar if not improved shovel dig rates. The design for the initial blast took a conservative approach to ensure the key blast outcomes of fume control and fragmentation were achieved.The second blast used the same pattern dimensions as the benchmark bulk product used in this area to provide a cost neutral comparison with the benchmark products that had been used over the prior six months. This resulted in a 20 per cent lower powder factor than would have otherwise been used. To test the suitability of XLOAD, this shot was slept for over two weeks between loading and firing in geology where the sleep time is typically kept to a few days to minimise the fume risk.The third blast utilised a slightly larger drill pattern to push the capabilities of XLOAD and provide a cost neutral comparison between the trial product and the traditional benchmark products. All three blasts were fired with no fume observed, no recordable incidents and good fragmentation. Shovel productivity from all three of the trial blasts was excellent with higher average instantaneous dig rates being recorded (average six per cent improvement against the instantaneous dig rates recorded for the benchmark blasts).Citation:Rock, J and Bambrook, K, 2016. Controlling Blast Related Fumes with Unconventional Explosives, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 39–49 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By M A. González, J A. Romero, D L. Fuentes, C J. Poblete, O Abdrashitova

"Robustness can be defined as the ability of a system to resist change without adapting its initial stable configuration. Robust design methodology, which is widely accepted in the manufacturing industry, allows the establishment of robustness and reliability metrics in scenario analysis.In the mining industry, a mine can be considered as a system with design parameters such as processing plant and mining capacities. Traditionally, a limited number of scenario iterations are performed in an attempt to determine optimal capacity values. An important strategic decision such as process plant capacity in particular is made during the very early stages of a mining study, often based on a low level of information. Lack of time and tools to run and analyse a larger number of possible scenarios for different design parameter combinations are usually the main reasons for not performing a full analysis. In addition, the uncertainty of other mining study input parameters creates more risk in decision-making.With advances in technology, it is now possible to automate the process of generating several thousands of scenarios in an affordable and timely manner. This allows performing the results analysis and assessing robustness and reliability criteria within a reasonable time frame. It is possible to generate a surface of results based on the net present value (NPV) for each scenario. This surface will reflect the efficiency level of the capture of the economic rent for each production scale. In addition, each scenario can be tested under diverse conditions of volatility of other external variables such as prices, costs or recoveries for example.This paper aims to establish a methodology that applies robustness criteria to determine the best scenario on several surfaces of value, which is then assessed with real data from a mining project. Obtained results demonstrate the advantages of using the proposed methodology in dealing with the above-mentioned multidimensional problems. It allows better decision-making on key design parameters and better control of the risks of a strategic mine plan.Citation:Poblete, C J, González, M A, Romero, J A, Fuentes, D L and Abdrashitova, O, 2016. Use of Robust Design Methodology for Production Scale Definition in Open Pit Mining, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 284–291 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By A K. Ghosh

"Inrush of water is always an issue, especially for mines located in heavy rainfall areas. Nowadays, mining companies and research institutes have developed many advanced technologies for study and analysis of hydrological processes. In this paper, an advanced method is introduced, which uses the Shuttle Radar Topography Mission Digital Elevation Model (SRTM DEM) data in the Geographical Information System (GIS) platform to simulate the stream distributions around two specific mines: Super Pit and Griffin coalmine in Western Australia. The impact of this approach is important because it reduces the time and economic cost by creating a high spatial resolution hydrological map in the specific areas. The study identifies the flow path of the run-off water, which helps in adopting a suitable water management plan surrounding the case study mines. The results match with the ground reality. Based on the results, the stream structure around Griffin coalmine is more complicated than that of Super Pit. The bifurcation ratio and drainage density are computed to estimate the subsoil permeability characteristics of the two mines. Recommendations have been put forward to prevent and reduce the potential risks of water accumulation around the open pit mines.Citation:Ghosh, A K, 2016. Application of Shuttle Radar Topography Mission Data in Hydrological Analyses of Super Pit and Griffin Coal Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 162–169 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By N Redwood, N Fowkes, A Bassom, S Durkin

"It is well known that from time-to-time a vehicle will interact with a bund or windrow and often the barrier is insufficient to safely arrest that vehicle. The result of such an incident is often catastrophic. Regulations around the requirement for edge protection near pit edges vary between jurisdictions. Generally in Australia regulations tend to be around placing the responsibility on the mine operator to provide ‘adequate’ or ‘appropriate’ edge protection. Guidelines often place a minimum height of bund at between half and two-thirds the diameter of the largest tyre on-site.Safescape has identified the opportunity to improve safety in open pit edge protection and is currently developing the Edge Protector (EP) product. The EP is designed to create a vertical front face to a conventional broken rock safety bund. The fundamental premise of the product is that by creating a vertical front face to the bund, trucks cannot easily drive up over the bund and instead have to push through the rock to get to the other side.In addition to providing a safer system for arresting vehicles, the vertical front face also means that extra space is made available in the haul road. This can either be used to facilitate larger trucks or when designing a new mine, with an increase in overall pit slope.This paper outlines the research and development of a new edge protection product. Discussion will include project objectives, economic incentive for mines to apply the system, mathematical analysis of the truck/bund interaction and physical testing of the product.Citation:Durkin, S, Fowkes, N, Redwood, N and Bassom, A, 2016. Innovative Approach to Open Pit Edge Protection, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 138–149 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By S Casas Castellanos

"Tyres consumption is one of the costliest branches of the operation in a truck-based haulage mine. Off-the-road (OTR) tyres working within undesirable conditions have a considerable negative impact on the whole mine’s productivity. Only the rolling resistance due to underinflated tyres could increase truck fuel consumption by 15 per cent. The impact of other conditions such as road surface quality and temperature are difficult to estimate. Tyre management is a demanding activity that requires a high level of coordination between maintenance and production departments.The project is aimed to develop a smart decision tool to assist mine managers to optimise tyre resources. By identifying factors that have significant impact on tyres, managers are able to take timely action to mitigate undesirable working conditions.The proposed model utilises real-time tyre measurement of pressure, temperature, speed, load, deformation and surface profile to report tyre performance in terms of tonne-kilometre-per-hour (TKPH) and tyre longevity. Both indicators are permanently monitored in order to trigger a warning system designed to keep tyres under optimal working conditions.An interactive database ‘Octo-Mine’ wirelessly receives records from a programmable logic controller (PLC) deployed on the truck. PLC records are the integration of multiple sensor signals with a time stamp. Octo-Mine utilises real-time and historical tyre records to generate online performance and longevity reports, as well as preventative and corrective tyre maintenance scheduling, by comparing current tyre status with established standards.To validate the model, the prototype database was populated with hypothetical data to simulate ideal working conditions subject to comparison with real field observations. Additionally, a laser-based technology prototype device successfully measured a new 9 mm tyre tread and a 60 000 km rolled tyre tread in the laboratory.In conclusion, optimal tyre management contributes not only to reduction of tyre waste but also to truck energy efficiency. This project is a first step in proving these benefits under real field conditions. It suggests that further development of sensor equipment and its integration with a communication system is a worthwhile focus for future research.Citation:Casas Castellanos, S, 2016. Optimum Management of Truck Tyres in a Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 212–228 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By W Zeng, D Walker, D Cai, E Baafi

"The efficiency of the truck-shovel haulage system is significantly influenced by the truck fleet size. A discrete event simulation model with 3D animation has been developed to estimate the productivity of a truck-shovel network system, shovel efficiency, truck cycle time, truck utilisation and the optimal fleet size. The simulation model considers the dynamic variability of traffic conditions and also the truck as an individual entity. The resulting truck cycle time was found to be realistic and thus providing a better tool for strategic mine planning.Citation:Zeng, W, Baafi, E, Walker, D and Cai, D, 2016. A 3D Discrete Event Simulation Model of a Truck-shovel Network System, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 265–273 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By M Brockman, M Cowan, A Robeson

"Sunrise Dam Gold Mine (SDGM) is located 820 km from Perth, 220 km from Kalgoorlie—Boulder and 55 km south of Laverton in Western Australia. The SDGM main pit had successfully operated since 1997 and was due to be completed during 2012. An opportunity existed to extract the high-grade crown pillar – 600 kt @ 7 g/t for 135 koz by either open pit or underground methods.The crown pillar was the 60 m (vertically) thick remaining part of the high-grade Cosmo orebody between the top of the paste filled underground mine stopes and the planned base of the final open pit shell.There were two major difficulties being considered when choosing the underground or open pit options:a major wall failure in the upper section of the main pit wall directly above the crown pillar restricting access from the base of the open pit to the top of the crown pillarimpact of a high rainfall event while the crown pillar was being mined from either surface or underground resulting in flooding of the underground mine workings.This paper will discuss the following issues:the process to identify and evaluate the risks in both options using knowledge based modelling software; this technique allowed the evaluation of a complex set of assumptions to arrive at the preferred optionremediation of the Watu failurethe selection of the preferred option and the challenges encountered before, during and after the extraction of the crown pillarthe planning and geotechnical work to ensure the safe extraction of the crown pillarsuccessful outcomes transitioning from open pit operation to a solely underground operation.Citation:Robeson, A, Cowan, M and Brockman, M, 2016. A Case Study on the Assessment, Planning and Extraction of the Crown Pillar at Sunrise Dam Gold Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 115–136 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By N M. Player, R P. Varden, E Jones

"An effective geotechnical design provides an accurate and appropriate assessment, balanced with a mining company’s risk profile. Justifying the cost of slope assessment requires an understanding of the input sensitivities, and resultant risk, to achieve a slope of a required functionality. As a project progresses from Scoping to Feasibility, the geotechnical risk becomes better resolved through increased expenditure on drilling, testing, analysis and modelling as long as the input data is appropriately spatially distributed. Providing accurate and appropriate geotechnical assessments in the early stages provides confidence in all following stages, especially where initial analysis indicates difficult geotechnical conditions. It is also in the early stages of project definition that there is most opportunity to maximise the value of the deposit through investigations into optimal mining methods.This paper examines the advantages of geotechnical engineering input through a project study period. Early geotechnical involvement allows the Scoping and Pre-Feasibility Studies to be more effective. Operational risks can then be better understood and dealt within the Feasibility Study phase, also ensuring that the correct risks and management controls are put in place.With commodity price pressure and cost of resource recovery in a downturned industry, reducing the risk to cash flow, resource recovery and safety should be a primary goal for all mining companies. Reduced risk can be effectively achieved through geotechnical design of slopes to achieve a required performance as part of an integrated study to the Reserve definition and mine design.Citation:Varden, R P, Player, J R, Player, N M and Jones, E, 2016. Justifying Slope Design Risks and Costs, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 185–201 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By D J. Robinson, L L. Kuhar

"Regardless of orebody value, at some stage, the pit will reach a depth where the reward for mining wider and/or deeper is not justified by the anticipated returns. ‘Last-blast’ strategies may help to some degree in recovering additional quantities of the resource but when a pit remains, there is often significant value left in the ground. In addition, in many cases, one or many good reasons may dictate why going underground and pursuing the orebody below the pit is also not justifiable. Whereas the company can hopefully move on to other more prospective parts of the orebody, the remaining options for the pit are usually very limited. Typically the pit is either held for potentially more favourable future pit expansion opportunities or it could be used for an alternative purpose, such as tailings or waste storage. This paper will present an alternative option that involves the direct extraction of values using in situ recovery (ISR) methods to recover additional value metals from the walls and/or floor of the pit. ISR involves circulating a fluid through the remaining orebody, solubilising the target metal and subsequently returning the solution to the surface for metal recovery. ISR is not the panacea to all but it has been employed selectively in the minerals industry for some time and the production of metals, such as uranium, rely heavily on this approach. ISR is not yet considered by many operators as an approach to compete with open pit or underground mining, largely because of the perceived limitations of this approach and the perceptions of risk. Rapid recent development of tools and enabling technologies relevant to ISR have made us reconsider the most economic approach to extracting many other metals from known mineral systems, even those currently listed as subeconomic. We suggest that ISR has the potential to make mine operators rethink the end of the pit life and adopt an innovative ISR approach to work toward a more complete recovery of value metals from existing pits.Citation:Kuhar, L L and Robinson, D J, 2016. In-pit In Situ Recovery - a New Approach That May Allow for Increased Value Extraction before Pit Closure, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 275–283 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By Alberto Martín Ríos Carranza

"El presente texto señala la información técnica del proyecto de Santa Gloria. Dicho plan revisa las estimaciones de reservas, recursos y potencial exploratorio, información metalúrgica, infraestructura y otras generalidades. El proyecto se ubica en la provincia de Huarochirí en la región Lima, cuya infraestructura tiene permisos ambientales, certificado de operación minera (COM), uso de aguas, convenios para la utilización de energía eléctrica y buenas relaciones con las comunidades campesinas del entorno. Adicionalmente, cuenta con una planta de flotación para el tratamiento de mineral con una capacidad de 30 TM/día. La concentración de estructuras mineralizadas (vetas) está distribuida en tres áreas que se han denominado zonas Eleine, Tembladera y Santa Cruz. La mena de sulfuros tiene una recuperación alta en la planta de flotación (90.79% en plata) puesto que los sulfuros (tetraedrita y galenas argentíferas) no contienen minerales de manganeso."

Nov 1, 2016

By W. R. Reed, J. P. Rider

"The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) recently developed a series of models using computational fluid dynamics (CFD) to study airflows and respirable dust distribution associated with a mediumsized surface blasthole drill shroud with a dry dust collector system. Previously run experiments conducted in NIOSH’s full-scale drill shroud laboratory were used to validate the models. The setup values in the CFD models were calculated from experimental data obtained from the drill shroud laboratory and measurements of test material particle size. Subsequent simulation results were compared with the experimental data for several test scenarios, including 0.14 m3/s (300 cfm) and 0.24 m3/s (500 cfm) bailing airflow with 2:1, 3:1 and 4:1 dust collector-tobailing airflow ratios. For the 2:1 and 3:1 ratios, the calculated dust concentrations from the CFD models were within the 95 percent confidence intervals of the experimental data. This paper describes the methodology used to develop the CFD models, to calculate the model input and to validate the models based on the experimental data. Problem regions were identified and revealed by the study. The simulation results could be used for future development of dust control methods for a surface mine blasthole drill shroud. IntroductionIn surface mines, production drilling is an essential process in blasting to fracture the hard rock overburden for removal. During the process, considerable amounts of respirable dust are produced. Past sampling at the shroud area of blasthole drills had documented time-weighted-average respirable dust concentrations ranging from 8.68 to 95.15 mg/m3 (Organiscak and Page, 1995) and 1.04 to 52.30 mg/m3 (Listak and Reed, 2007). These high dust concentrations, which may contain silica, can lead to respirable dust overexposures for the miners working nearby. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is ultimately fatal.Two basic methods are used to control drilling dust: a wet suppression system or a dry collection system (Cecala et al., 2012). Dry drilling techniques using a dust collection system are preferred in rural mining locations where a constant water supply is not available, and in the case of rotary drilling where water is associated with accelerated bit wear due to bearing degradation and hydrogen embrittlement. In addition, dry drilling eliminates freezing-related issues with water in colder climates. Dry dust collectors are highly effective at removing dust, especially the finer material, as long as they are properly operated and maintained (Listak and Reed, 2007; Organiscak and Page, 2005)."

Nov 1, 2016

By C. L. Kosmoski, B. M. Eiter, B. P. Connor

"In the recent past, the mining industry has witnessed a substantial increase in the numbers of fatalities occurring at metal and nonmetal mine sites, but it is unclear why this is occurring. One possible explanation is that workers struggle with identifying worksite hazards and accurately assessing the associated risk. The purpose of this research was to explore this possibility within the mining industry and to more fully understand stone, sand and gravel (SSG) mine workers’ thoughts, understandings and perceptions of worksite hazards and risks. Eight mine workers were interviewed and asked to identify common hazards they come across when doing their jobs and to then discuss their perceptions of the risks associated with those identified hazards. The results of this exploratory study indicate the importance of workers’ jobrelated experience as it applies to hazard identification and risk perception, particularly their knowledge of or familiarity with a task, whether or not they had personal control over that task, and the frequency with which they perform that task. IntroductionAccording to the U.S. Mine Safety and Health Administration (MSHA, 2015a), 37 mine workers were fatally injured in accidents at metal and nonmetal mine sites between October 2013 and January 2015, following a record low of 16 in 2012 and in 2011. In 2014 alone, 29 mine workers were fatally injured at a metal or nonmetal mine site, and 52 percent of these fatalities occurred at a surface stone, sand or gravel (SSG) mine. In January 2015, Joseph A. Main, Assistant Secretary of Labor for Mine Safety and Health wrote to stakeholders in the metal and nonmetal mining community and identified several areas where improvement was necessary to promote the health and safety of mine workers. One area identified was an increased focus on “daily and effective workplace exams to find and fix hazards” (MSHA, 2015b).Hazard detection is challenging in the mining industry, despite the existence of regulation. Mining is a major undertaking involving the use of complex heavy machinery, equipment and processes as well as numerous and diverse worker activities that take place in a dynamic, challenging environment (Scharf et al., 2001). In other industries that are similarly dynamic and unpredictable, such as the construction industry, a large proportion of hazards go undetected (Carter and Smith, 2006). It is critical that miners are able to both recognize worksite hazards and accurately assess the risk associated with the hazards, because their health and safety depend on their deciding whether and how to remove hazards and mitigate risks."

Nov 1, 2016

By R Dunne

"Continuous improvement on metallurgical treatment plants is possible only when good data and analysis of the data are available. Good data implies appropriate and accurate mass measurement coupled with good sampling practices and accurate chemical analysis especially when carrying out monthly metallurgical metal reconciliations. Adequate characterisation of key samples (eg tailings, feed, concentrates and others) at timely intervals is an important part of a good continuous improvement program. The data from this will help identify opportunities to improve operation performance and thus profitability. Examples are provided of projects that have led to improved plant performance based on good metallurgical data collection and analysis.Citation:Dunne, R, 2016. Using Metallurgical Data to Drive Continuous Improvement, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 201–206 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By E Beltran, S Ngunz, F Orrante, F van Zyl, M Westcott

"The primary control objective of the project is to achieve milling optimisation by ensuring that the energy available for rock breakage is used as efficiently as possible. This is achieved by increasing the level of mill filing until a process constraint is reached. Stable operation against this limiting constraint is then maintained to ensure long-term optimised operation.Semi-autogenous grinding (SAG) mill control optimisation presents a number of challenges. SAG mills have multiple inputs that are used to control multiple outputs (MIMO process). Secondly, the SAG mill loading process is a ‘high inertia’ process that can be approximated as an integrating process. This means that it is open-loop unstable. The hybrid control strategy presented implements an advanced ‘load stabiliser’, which transforms this integrator process into a more manageable first order process, which can be steered stably against the constraints. This SGS hybrid Expert control strategy implemented on both SAG mills at the Porgera concentrator therefore consists of two integrated parts responsible for:stabilising the mill load to a targetdriving the mill load target to the maximum determined by the process constraints (eg maximum power draw) to maximise efficiency and throughput. A comparative study is done between the operation of the plant for a period of a month before and a month after the implementation of this strategy. The results indicated a significant improvement in the SAG mills’ stability and operation as well as a reduction of overload situations leading to a loss of throughput.Citation:Ngunz, S, van Zyl, F, Orrante, F, Beltran, E, Westcott, M and Wilson, S, 2016. Simplified Hybrid Semi-autogenous Grinding Mill Control - Explanation and Practical Results at the Porgera Concentrator, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 313–320 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By B Murphy, T Mattsson, R Crosbie, T Maksimainen

"An Outotec e500 TankCell, with 500 m³ of actual flotation volume, was commissioned at the Kevitsa Cu-Ni-PGE concentrator in northern Finland during 2014. This flotation cell was implemented at the head of the existing copper circuit as the first Cu rougher flotation cell. This was the first flotation cell of this size to be run under production conditions by any supplier anywhere in the world.The cell has been in continuous operation since start-up in October 2014 and has provided improvements in metallurgical performance at very low specific power consumption. On average, the cell has recovered 71 per cent of copper contained in the 0.37 per cent Cu flotation feed at a concentrate grade of 17 per cent Cu. The specific power consumption for the cell (excluding blower power) is typically around 0.4 kW/m³.After start-up, the impeller speed and superficial gas velocity were varied and the impact on metallurgical performance measured. In this paper a review of the cell operation at Kevitsa is given. Furthermore, the impact of mixing and gas dispersion on metallurgical performance is presented.Citation:Crosbie, R, Mattsson, T, Murphy, B and Maksimainen, T, 2016. Metallurgical Performance of Outotec's e500 TankCell at the Kevitsa Cu-Ni-PGE Concentrator, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 127–134 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By R A. Pax, B Cornish

"Although it is well known and easily experienced that the feed size distribution influences the throughput and stability of operation of a semi-autogenous grinding (SAG) mill, the details are poorly understood since it is often only the input and output measurements that are used to identify unfavourable in-mill conditions. Load cells and power monitoring are sometimes used but are generally poor indicators of the mechanisms that lead to such unwanted conditions.At the MMG Century operation a 12-microphone array around the SAG mill using non-contact acoustic measurement methodology has been used to diagnose the in-mill conditions to facilitate improved throughput and stability of operation. Use of acoustic measurement and control has provided a demonstrated increased throughput of at least 20 per cent as well as improved stabilisation of the mill. Since the information derived from the acoustic noise from a mill allows discrimination of the behaviour of the steel balls and the rock, a number of in-mill conditions can be identified with signals that include toe and shoulder angles, water holdup and the ball to rock ratio.Feed size variations, measured online with an imaging system, have been used to determine their effect on the internal charge behaviour. It has been found that circumferential segregation of steel balls and rock occurs as well as poor mixing of large rocks. Both of these effects are not conducive to optimal breakage rates of different size fractions. Longitudinal segregation effects also occur. This paper presents and discusses these results and illustrates how the new acoustic knowledge can be used to manage and improve mill operation and stability.Citation:Pax, R and Cornish, B, 2016. Understanding Size Effects of Semi-autogenous Grinding (SAG) Mill Operation as a Pathway to Solving Feed Disturbances - Case Study using the MMG Century SAG Mill, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 321–330 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By T Day, I G. Robertson, G J. Lyman

"Various approaches are used in the industry for establishing procedures (sample mass estimation and method of subsampling) for sampling and analysis of gold ores. The key factors that determine the accuracy of the results that can be expected for a given set of procedures are widely misunderstood.Recent developments in sampling theory show that the estimation of the accuracy that can be expected for a given gold ore as a function of sample mass is actually a simple matter. For a given sample mass, the accuracy that will be achieved depends only on the grade of the ore and the range of masses of the grains of the gold in the ore. This, of course, demands that a reasonable estimate of the distribution or spread of gold grain masses in the ore be known. But this is something that should be known if the gold is to be efficiently recovered in the processing plant.This paper provides a simple explanation of the real facts about sampling of gold, either in the field or in the plant, and provides results for a number of cases of combinations of fine and coarse gold in an ore. The prerequisites for accurate gold sampling are:correct sampling with no loss of sample or contaminationsample preparation procedures that recognise the impact of the gold grain mass spreadpractical analysis of the sample masses required to provide acceptable accuracy.Issues of corporate governance are also discussed.Citation:Lyman, G J, Robertson, I G and Day, T, 2016. The Simple Facts about Sampling Gold Ores, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 159–172 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By B Nielsen, H Lehto, B Musuku

"The demand for fine and ultra-fine grinding associated with the processing of more challenging, finer grained orebodies and the global driver of minimising energy consumption has been an increased focus in our industry. Outotec’s stirred milling technology, the high intensity grinding mill (HIGmill™), was launched in 2012 in response to this industry need. First Quantum Minerals Ltd selected HIGmill™ technology for its Kevitsa mine in Northern Finland. The 700 kW mill is grinding copper rougher concentrate to improve copper/nickel separation and copper recovery. Selection of the HIGmill™ followed mineralogy analysis and laboratory and pilot testing for HIG milling in parallel with flotation tests to determine optimum grind size and energy input.The paper discusses the challenges and successes of the test work, manufacture, installation, commissioning and subsequent operation of the mill. Grinding performance is presented and a comparison between predicted and operating energy efficiency is made. In addition, the various steps to optimise wear rate and minimise maintenance and downtime are made, with particular reference to internal geometry of the mill.Citation:Nielsen, B, Lehto, H and Musuku, B, 2016. Design, Installation, Commissioning and Operation of Fine Grinding Technology at the Kevitsa Mine, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 59–66 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By H Kurth

"The focus of this paper is on measuring the composition to improve mill feed quality to minimise the processing of waste, optimise process performance, reduce processing costs and minimise the generation of tailings.Technologies used since the 1990s in the cement and coal industries for measuring conveyed materials have been operationally proven and effectively derisked. Despite this the acceptance by the minerals industry has been very slow except in iron ore. Real-time penetrative full stream measurement using prompt gamma neutron activation analysis (PGNAA) for multielemental analysis and microwave transmission for real-time moisture analysis provide representative, tonnage weighted dry weight per cent results on a minute by minute basis. Analysis is unaffected by particle size, dust, layering/segregation, mineralogy and belt speed. The technologies are explained and performance examples given. The benefits derived from real-time compositional analysis are predicated upon a good understanding of deposit geology, mineralogical associations, waste to ore interfaces, amenability to mining, metallurgical processes and downstream customer requirements. Processing may include basic preparation in the case of direct shipping ores, minor beneficiation using simple upgrading methods, or concentration using more complex processing systems such as flotation, leaching or many others. The value of real-time data from primary crushed conveyed flows, using analysis of increments smaller than a single haul truck’s load, is very beneficial in process plants aiming to reduce waste processing, increasing feed grades and increasing metal recoveries. Grade variability can be utilised to divert conveyed increments of waste, direct shipping ore (DSO) quality material bypassing beneficiation, and subeconomic material amenable to upgrading diverted for further preconcentration by particle separation (sorting, heavy medium etc). Paybacks of a few months have been commonly achieved where the real-time technologies have been applied in the minerals sector. The paper outlines proven applications and case studies and proposes some innovative applications.Citation:Kurth, H, 2016. Measuring and Utilising Ore Quality Variability Using Real-time On-belt Elemental Analysis to Improve Mill Feed Quality, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 239–244 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By T D. H McGrath, R Byleveld, W P. Staunton, J J. Eksteen

"The Gold Technology Group at Curtin University through the AMIRA P420 series of projects has recently developed the integrated liberation leach model (ILLM) for optimisation of gold plants. The model encompasses recovery by both gravity (batch centrifugal concentrators or BCCs) and leach adsorption (CIP/CIL) circuits. The ILLM essentially combines the Group’s well-known standalone models (ie gravity and SIMCIL) to create a robust simulation package.The ILLM process model provides a tool for sites to determine optimum set points for operations to optimise recovery (eg target grind size). It can also be used to predict the effect on gravity recovery, leach recovery and overall recovery when changes are made to circuit design, either temporarily (eg a leach tank taken off-line for maintenance) or as part of a circuit expansion (eg expanded gravity circuit capacity, or addition of leach tank capacity).This paper discusses the capability of the ILLM process model by highlighting a recent case study. The paper also addresses the test work and plant data required as model inputs, as well as limitations and the application of the ILLM to greenfield projects.Citation:McGrath, T D H, Staunton, W P, Eksteen, J J and Byleveld, R, 2016. Application of an Integrated Liberation Leach Model for Process Optimisation, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 173–178 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016